Z77A-G45 - Static sounds on USB ports

(pls move to correct forum, srry for the :censored:up)
Hi all,
Problem:
I recently bought a Z77A-G45 for my new rig. However it has static\electrostatic noise on the USB ports. Meaning as soon as i plug in USB speakers or my Razor Carcharitas headset (USB powered) i hear static noise of the insides of my computer. Normal 3.5mm audio output is without static, even when amplified via external amplifier.
These noises are loudest while browsing or other internet traffic, however they are always present and start right after POST.
Troubleshooting tried:
- Different BIOS settings regarding USB
- Even the problem also exist outside the OS, i tried different combination of drivers (beta & officia) for NIC & Audio
- Check and measured all grounding (and checked for ground-loop)
- Removed all hardware except for MOBO+CPU+PSU+RAM and disconnected everything external including front-panel, to insure my perhipicals are not causing the problem
- Did a 10pass memtest
- Flashed the latest stable BIOS
- Separated all cables inside the case and grouped all power & data so no interference is present
- Tried my old Spire 650 Watt PSU
My build setup:
- Coolermaster  CM 690 II advanced
- MSI Z77A-G45
- Intel i5-3570k 3.4Ghz (Ivy) (CPUID: 0306A9
- Scythe Mugen 3 PCGH-Edition
- Corsair 8GB (2x4 dualchan in sock 2&4) 1600-999 Vengeance LP
- Samsung 840 Basic 256GB
- Seasonic G450 Powersupply (80+ gold cert)
- Sapphire HD7950 (+boost)
Details MSI Z77A-G45:
- S/N: 601-7752-040B1209097231
- BIOS: V2.9 / 20130118
Kindly help me troubleshoot to decide if my product is defect and need RMA, or if this is fixable.
EDIT: as i also had the boot problem i just updated to BIOS A02 2.10, however problem still persists as soon as computer is powered-up, i honestly do think this is hardware related ?
KR
Kamaradski

That doesn't appear to be a US model, and this is the forums for Toshiba USA. You may want to contact Toshiba in your region. If it's a European model, you could check the Toshiba Europe forums.
- Peter

Similar Messages

  • Sound and USB ports suddenly not working

    I have HP pavilion dm3-1103au which i bought about 3 years ago.. Everything was worked fine since the first time I use this notebook until about 3 weeks ago when I used it to watch a film suddenly the sound changed to noise sound and then my notebook sound not coming out at all from speaker and headset.. Then I restarted my notebook and then the sound working normally but after a moment the sound stop coming out again..
    I check my sound driver to see any updates but it say my driver are up to date.. Then I go to sound control and test my speakers but it shows a warning that says "the device is being used by another application. Please close any devices that are playing audio to this device and then try again." I dont know what application that is using the sound because it happen when I didnt open any app..
    After about several days later, the problem seems to became worst.. All USB ports suddenly have a problem too.. My USB mouse stop working at random time.. Then I try to insert my flashdisk and sometimes it can be recognized but when I try to copy files to my flashsdisk, it disconnected when the process of copying has not finished..
    when i go to device manager the 'standard openHCD USB Host Controller' have a warning sign.. I check for updates but it says the driver was up to date.. So I try to uninstall it and restart my notebook.. but it didnt solve the problem..
    I have reinstall and upgrade my windows from windows 7 to windows 8 but it still have the same problem and become worst.. now the sound not coming out at all from the speakers and headset from the windows starts.. Please help me.. I have no idea what cause the problems.. I think it's not hardware related..

    Hello lynz00,
    Did you check out this page to see if your computer has been tested by HP with Windows 8, prior to upgrading to Windows 8?  
    HP is not going to support hardware for Windows 8 on any system purchased before Oct 1st 2011.  I realize your issue began prior to upgrading to Windows 8, but don't think the upgrade is the way to fix it.
    Did you backup everything in Windows 7 in order to downgrade, prior to upgrading to Windows 8?
    ↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

  • Recording Sound via USB Port

    How do I record sound from an audio tape into iTunes? Preferably via USB port,

    iTunes does not record, so you will need other software to record from your tape. There are a number of audio recording applications available, depending on your needs, including GarageBand, Audacity and many more. Whether any will record a USB device will depend at least somewhat on the device you will be using.
    Regards.

  • Z77A-G45 - No sound

    Hi everyone!
    I bought MSI Z77A-G45
    I am using with
    Chassis Thermaltake V4 Black Edition
    Edifier X100B Multimedia Speakers
    Windows Home Premium 64
    The PC is working fine, it beeps when i turn it on, but except for that i get no sound
    I believe i made all connections right, but i cant get any sound from multimedia or even phones plugged in. I read the mainboard manual and everything seems to be right, but to be honest i am new to this and i might have made wrong connections. Anyone have any ideas about what could be wrong. I also would appreciate if anyone show me how to check if i made all the connection in the right places.
    Thank you!!

    Download and install the most recent drivers for everything:
    http://www.msi.com/product/mb/Z77A-G45.html#/?div=Driver&os=Win7%2032
    Are you connecting via analog or digital?

  • MSI Z87-G45 Gaming, sound from USB mouse?

    Hi!
    I have some issue from my new computer, see spec below.
    For the information I have a MSI Z87-G45 motherboard.
    I have some sound that occurs sometimes (specially during the first 2-5 minutes) when i move the mouse around.
    It occurs as well sometimes when I been using the computer for a while, basically random just more frequently at the start-up.
    It's hard to know from where the sound occurs, could be PSU but today I read something on another forum about the motherboard I'm using:
    - Higher sound quality using USB, thanks to special adapted current power.
    So i wounder if this can be the case? Is that the reason why i get this noise from inside the computer?
    Is there some way to disabled this "feature" in BIOS?
    Greetings
    |Asus 24" LED VG248QE 144HZ (2st) | EVGA GeForce GTX 780 3GB PhysX CUDA | Intel Core i5-4670K | MSI Z87-G45 Gaming, Socket-1150 | Corsair SSD Force Series GS 240GB 2.5" | Fractal Design Define R4 Black Pearl | Crucial DDR3 BallistiX Tactical 16GB | Corsair TX 850W PSU | Noctua NH-U14S CPU Kylare | CM Storm QuickFire TK Keyboard Brown | Ace Laser Gaming Mouse EDGE 3200 | QPAD XXXL |

    The sound sounds like the old mechanics hdd kinda.
    It comes inside the computer, not the speakers.
    My feelings is that it can be the PSU as well, just wanted to check this first, since it most often comes when i move my mouse.

  • No sound and USB ports do not work.

    Hi I have a HP Compaq SR5013WM I have a red x on the speaker no audio output device is installed I have reinstalled the driver over and over again checked the BIO download from Realtek ALC 888S, R2 57 and knowing has helped the Motherboard ASUS P5LP-LE  Leonite GL8E 2 USB in the front 4 USB in the back any thing i plug in is unknown and will not in stall. PLEASE someone help.

    Sorry I forgot to add that i have a Satellite A665-S6086.

  • USB ports and sound have stopped working

    As the subject reads, all 3 of my USB ports have stopped working and all sound.  In the device manager I receive a (code 10) for realtek high definition audio.  I have done everything I can think of at this point, I have even done a complete OS reinstall. Afterwards I have also updated with every possible driver file I can find from realtek and toshiba, I really don't know what else to do at this point, any thoughts? advice? anybody else with this problem?
    Windows 7
    Toshiba Satellite
    L505D-S5983

    Same here. I have an L505D that is doing the same exact thing. No sound device, all USB ports not working and the SD card reader not working either. Also when you close the lid and reopen it, the machine won't wake up. Have to restart to get it to come back. Haven't found ANYTHING in forums to help.
    Sound devices, USB ports and SD card doesn't show up in the Device Manager.
    Took the laptop to a local fixer-upper. Unhooked the charger, took battery out, put battery back in, then restarted the laptop without being hooked up to the charger and everything came back on. But only for a short while. After a couple of days, it does its thing all over again.
    Are we looking at a mother board issue here? SURELY someone out there in cyber space has a solution.

  • Robotic Static Sounds USB Headset

    Issue: When using any USB headset or USB audio input device on any Macintosh with any operating system from 10.5.7 to 10.6.1, after about 10-20 minutes of use, all audio from the headset becomes garbled and has a robotic static sound quality.
    Tested with: Dozens of different Macintosh Computers over the last 6 months with different USB headsets and microphone input devices.
    Reproducable: Yes, via either Garageband, Ventrilo or a number of other software applications that do USB Audio Input
    References:
    http://www.ventrilo.com/forums/showthread.php?t=37302
    http://forums.worldofwarcraft.com/thread.html?topicId=17367983174&sid=1
    http://discussions.apple.com/thread.jspa?messageID=9983346&#9983346
    http://ministryoftruthblog.blogspot.com/2008/10/fixing-usb-audio-static-on-mac-o sx.html
    http://forum.skype.com/index.php?s=d9c3718b7185c8e1caee585c248c3bab&showtopic=75 528&st=40
    Additional Information and attempted fixes:
    • Tried it with a powered USB Hub
    • Switched the Audio Midi Setup input to 48k
    • Using Audio Midi Setup to create an aggregate device
    • Tried it on different Macs, Different Headsets and Different physical locations
    • Tried different USB ports
    Message was edited by: Jaycyn

    I have a 27-inch i7 iMac running 10.6.2 and I can confirm that replacing the kernel extension from 10.5.6 works just fine. I had been having this problem every since 10.6.2 (for some reason it worked up until then). I don't think this fix will work if you are booting with the 64-bit kernel (the default on ALL macs is to boot the 32-bit kernel so you would specifically have to be doing this). I haven't tested it in 64-bit though.
    Here are the steps I followed:
    1) Download the AppleUSBAudio.kext from 10.5.6 from the following URL.
    http://evo-wiki.cern.ch/twiki/pub/FAQ/AudioProblemMacOSX1057/AppleUSBAudio.kext. zip
    2) Unzip it.
    3) Open up terminal
    4) Make a backup of the existing driver by running the following in terminal
    cp -Rp /System/Library/Extension/AppleUSBAudio.kext ~/Documents/AppleUSBAudio.kext-BACKUP
    5) Exit any applications that are using a USB audio device and unplug all USB audio devices.
    6) Unload the existing AppleUSBAudio driver from the kernel by running the below command in terminal.
    sudo kextunload /System/Library/Extensions/AppleUSBAudio.kext
    If you get an error saying " not found for unload request" your fine. If you get an error claiming it can't be unloaded because its in use (don't have the text in front of me) then stop and go back to step 5.
    7) Remove the existing driver by running the following in terminal.
    sudo rm -rf /System/Library/Extensions/AppleUSBAudio.kext
    8) Put the new driver in place by running the following in terminal.
    sudo mv ~/Download/AppleUSBAudio.kext /System/Library/Extensions/AppleUSBAudio.kext
    9) Load the new driver by running the following in terminal.
    sudo kextload /System/Library/Extensions/AppleUSBAudio.kext
    10) Confirm the new driver is loaded by running the following in terminal.
    kextstat | grep AppleUSBAudio
    The output should look like the folliowing (the 2.5.8b13 is the important bit, some of the other numbers might be slightly different):
    cfb@snarfblat:~/> kextstat | grep AppleUSBAudio
    141 0 0x96c6f000 0x28000 0x27000 com.apple.driver.AppleUSBAudio (2.5.8b13) <95 94 30 14 8 7 5 4 3 1>
    At this point you should be good to go. The only issue with this "fix" is that any time there is an update from Apple there is a chance that the driver will get replaced with a newer one. After each update you should run the command from step 10 again to confirm that you have version 2.5.8.b13. If it gets updated, repeat the above process.
    NOTE: Jaycyn I have tried to post this to your WoW forum post of the same issue (http://forums.worldofwarcraft.com/thread.html?topicId=22048900603&postId=2204747 77020&sid=1#18) as that is how I found this thread and the solutions but there is something messed up with my forum account preventing me from posting to the WoW forums.

  • I've upgraded to OS 10.8.2 and my Bowers and Wilkins MM-1 Speakers were working fine until today, and now they won't play any sound at all, even though iTunes shows the audio is playing. I've tried both the headphone jack and the USB port. Please help!

    I've upgraded to OS 10.8.2 and my Bowers and Wilkins MM-1 Speakers were working fine until today, and now they won't play any sound at all, even though iTunes shows the audio is playing. I've tried both the headphone jack and the USB port. Please help! I don't want to have to be stuck using my internal speakers!
    Thank you,
    Chris

    Michael,
    Thanks. I haven't mixed down the audio or checked the number of tracks in Prefs. Good points.
    As far as a mixdown goes, I'll definitely give it a try, though I wonder whether or not the tracks will be recognized during mix down recording - given that you can't hear either of those segments in playback. Just have to try.
    Re the preferred number of allowed tracks - I'll go check as soon as I send this off, but I'm not sure that applies in this case, since the two Channels containing the segments that are pinked out are not in additional tracks. I should have mentioned that other audio clips and segments on the same Channels in the SAME tracks ARE heard in playback. As are two additional track in the 2nd Sequence. It's only when the two sequences are joined that the pink tinted segments can't be heard. Within the sequence the same audio cuts playback as they should. Thanks again &
    Best regards,
    David

  • IPod Touch 4th gen after updating to IOS 6.0.1 no longer plays sound when connected to a JVC KW-AV60BT through USB port.

    It used to work fine, but now when you plug in to the USB, it properly identifies the head unit in settings>General>About, and the JVC unit displays album art, track info and scrolls through music fine, but no sound comes through the speakers. I've tried to reset all settings on the iPod, I've tried the reset on the head unit, even disconnected the vehicle battery and nothing changes. I can also add that my sisters iPhone 4S on IOS 6.0.1 also performs the same when connected. I've tried my Touch in the USB port of my 2010 Chevy truck and that works fine. oh, and an MP3 player worked proper with the JVC USB port.

    - Try resetting the car system if you can.
    Sometimes this works
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:       
    iOS: How to back up           
    - Restore to factory settings/new iOS device.
    However. sometimes an iOS update breaks compatibility. In that case you will have to wait for a firmware update to either the care system or the iPod.

  • I have a macbook pro4.1 and the sound chip in it failed. My speakers and microphone no longer work. Does anyone know of an external speaker and microphone set that plugs into the USB port so I can continue to use both of these functions?

    I have a macbook pro4.1 and the sound chip in it failed. My speakers and microphone no longer work. Does anyone know of an external speaker and microphone set that plugs into the USB port so I can continue to use both of these functions and not have to pay to have the entire main board replaced. Preferably something under $100.

    I don't think you're likely to find a set of external speakers that come with a microphone and plug directly into a USB port. There are USB audio cards that look like tiny flash drives but have microphone and headphone ports in them, to which you can connect a typical two-plug Windows PC headset with a microphone, or else you can connect external speakers and a stand-alone microphone. Those adapters typically cost under $10. I don't know anything about the quality of sound that can be expected from them.
    I have a Griffin iMic, which is much the same idea but larger, a bit more expensive (retail~$40), and perhaps delivers somewhat better sound quality (I hope so, but I don't know because I've never had occasion to try one of the little ones).
    http://www.google.com/products/catalog?oe=UTF-8&hl=en&client=safari&q=usb+sound+ card&um=1&ie=UTF-8&tbm=shop&cid=9618463009759678039&sa=X&ei=tgQoT5zYOMfZ0QHkiICw Ag&ved=0CHcQ8gIwAQ
    http://compare.ebay.com/like/320779457703?var=lv&ltyp=AllFixedPriceItemTypes&var =sbar

  • Iphone 4 makes an continuous intermittent vibration/buzzing sound when plugged into any of computer's 3 usb ports; does not show in itunes or Windows Vista device manager. No problem charging the phone with other power sources. What's going on?

    This problem happened intermittently in the past but now happens every time I plug in the phone. I suspect it might be a problem with my computer, an Acer Aspire 4530, perhaps with it's charging function via usb ports? The phone makes the same buzzing sound twice when I connect to other power sources, but continues when connected to computer. I have this issue even when the phone is 100% charged.

    This problem happened intermittently in the past but now happens every time I plug in the phone. I suspect it might be a problem with my computer, an Acer Aspire 4530, perhaps with it's charging function via usb ports? The phone makes the same buzzing sound twice when I connect to other power sources, but continues when connected to computer. I have this issue even when the phone is 100% charged.

  • Since windows 8.1 usb ports and sound are acting strange

    Hello,
    Since I upgraded to windows 8.1 my sound randomly stutters(very anoying) and my usb ports get turned off, only the ports that have been occupied since boot, new things work, and not reinsterting the things that were present at boot, in the same or a different
    port doesn't work.
    Hell, why do we pay for an OS that doesn't even work?
    I expect that something as simple as an USB port or sound would work just fine.
    I have installed all the latest drivers but somehow windows seems to screw things up.
    When I boot up debian, I have no problems at ALL. And did I pay a dime for Debian? No, it is free.
    I am getting really depressed here, paying for stuff that doesn't work.
    So does anyone know any other way to fix this OS than by breaking the disc and never return to it?
    Thanks in advance.

    To whom are you telling that, this is an end user forum.
    If you have problems than contact Microsoft in your country.
    http://www.microsoft.com/worldwide/
    Success
    Cor

  • Bought iPhone 6 yesterday. Also bought dock works with iPhone 5/5s. And cord connecting iPhone 6 to USB port on car stereo. No sound comes out of dock or car stereo. In store today, iPhone 5 running ios 8 worked on dock, not iPhone 6. When Apple fix?

    I bought an iPhone 6 yesterday. I also bought a stereo dock that works with iPhone 5/5s. And a cord to connect iPhone 6 to USB port on my car stereo. No sound comes out of the stereo dock or car stereo. In Best Buy today, Sales Associate tried his iPhone 5 running iOS 8 on a stereo dock. It worked, but my iPhone 6 didn't. When will Apple fix this problem? Or is Apple pushing everyone to Bluetooth?

    The iPod feature that plays through USB in my car does not work with my iPhone 6 either.  I called AppleCare and they said that the car audio system will need a firmware update.  Don't know if Apple is just passing the buck, but that is what I was told.  Thank you for posting.  I know now that I am not the only one.  Thanks also for posting about the iPhone 5 running iOS 8.  I gave away my iPhone 5 to a friend so I wasn't sure whether this is an iOS 8 issue or an iPhone 6 issue and your experience seems to confirm that it is a problem with iPhone 6.  I guess I will just be using Bluetooth in my car, at least for now.

  • ITunes 11.1.2 sound is distorted, from the library from the store, from my external DAC. Tried swapping USB ports, reloading songs in an uncompressed format, etc. Sound is awful. Thanks for any ideas.

    iTunes 11.1.2 sound is distorted on my iMac, from the library from the store, from my external DAC. Tried swapping USB ports, reloading songs in an uncompressed format, etc. Sound is awful. Thanks for any ideas.

    I have the same issue.  If I open up the Equalizer and select any setting (including the one that is already checkmarked), the sound corrects itself.  However, it goes right back to crappy when a new song comes on. 

Maybe you are looking for

  • Wireless connection problems with iTunes

    After installing iTunes for my PC(using Windows Vista if that matters). Directly after installing iTunes my wireless connection works. Once I start importing my music into iTunes I lose my wireless connection. I can still see the wireless networks bu

  • Advice on best arrangement for home network

    This is my first post so go easy on me....please?! I have moved into a new apartment and am trying to set my network is the best way, but am struggling slightly. I have a WRT150N and WRVS4400N (Don't ask why I have both) both of which are brand new,

  • IMac G5 Hanging at spinning cog

    I first posted a request for help to this problem on another thread re spinng cog problems. Unfortunately no-one answered!  So I am posting it again in the hope that SOMEONE can help me or advise me as to what to do! I tried the various usggestions o

  • Subject: Where are SAP Exit Variables and how to use them in Bex Query

    I have seen references to variables:  0cyear (Current Year), 0CALYEAR (current year), oCALMONTH (Current month/year). Under 0CALMONTH characteristic or 0CALYEAR I do not see any of the variables, so how does one use these variable in the query. For e

  • Dynamic where clause - hard-parse

    Hi there, I landed in the middle of a situation that I'm not seeing any solution possible, so I'm turning to you for help. We have a batch script that occurs once a day that handles a lot of information (we're talking about thousands of data). In man