Z77A-G45: XMP works with one and only one ram stick.

I am having a problem when using XMP with two ram sticks. One and only one ram stick works fine. Here is the story.
I recently update my build with a set of G.Skill Ripjaws X Series 8GB (2 x 4GB) DDR3 2133. It had one Kingston 4GB 1333 stick in the past.
The new rams work fine at 1600 if I don't use XMP profile. However, every time when I load XMP, it fails to post. The power goes on for one or two seconds then goes off; then it restarts after a few seconds and fail again. This cycle goes on and on until occasionally it loads the bios and says OC setting failed and click F1 to setup.
I thought maybe the rams were bad so I unpluged one stick, then it started and worked perfectly. I tried either sticks with all the slots. If only one stick plugs in any slot, it always works with XMP; if both two sticks plug in, whatever combination of slots I use, it failed to start.
Does anyone have a clue about this?
Thanks.

G.Skill Ripjaws X Series 8GB (2 x 4GB) DDR3 2133
Due to most likely non standard SPD profiles, they probably need to be manually set up. That or the CPU IMC is weak. Some of the Beta UEFI/BIOS revisions may be available that addresses problems with this RAM. The change logs might indicate such. There are several variations of G45, so make sure the one I linked is the right one;
https://forum-en.msi.com/index.php?topic=161033.0

Similar Messages

ITunes has stopped allowing me to import CDs. if I reboot it will import one, and only one. all was working fine before. the itunes diagnostics have all green lights

iTunes has stopped allowing me to import CDs. if I reboot it will import one, and only one. all was working fine before. the itunes diagnostics have all green lights

For general advice see Troubleshooting issues with iTunes for Windows updates.
The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down page in case one of them applies.
Your library should be unaffected by these steps but there is backup and recovery advice elsewhere in the user tip.
If you've already tried a complete uninstall and reinstall try opening iTunes in safe mode (hold down CTRL+SHIFT as you start iTunes) then going to Edit > Preferences > Store and turning off Show iTunes in the Cloud purchases. You may find iTunes will now start normally.
You could also try working through
TS1717: iTunes for Windows Vista, Windows 7, or Windows 8: Fix unexpected quits or launch issues
tt2

ERROR ITMS-9000: "META-INF/container.xml must contain one and only one root file reference."

Hi all,
After correcting a table-of-contents error in my .epub file, I am unable to upload it via iTunes Producer. It lists this error message:
ERROR ITMS-9000: "META-INF/container.xml in 9780615431727.epub must contain one and only one root file reference." at Book (MZItmspBookPackage)
The file has been verified and only has one root file reference in the container.xml file.
Has anyone been able to find a solution to this problem?
Thanks!

Hello Forum Users…
For those of you who have run into the upload roadblock, getting an error message similar to this:
Package Summary:
1 package(s) were not uploaded because they had problems:
          /Users/slm/Desktop/MUSIC to PICTURE for IBOOK/2012 MTP for iTUNES Bookstore/9780615600918.itmsp - Error Messages:
                    Apple's web service operation was not successful
                    Unable to authenticate the package: 9780615600918.itmsp
                    ERROR ITMS-9000: "OPS/ibooks.ncx(5): 'p50': fragment identifier is not defined in 'OPS/content9.xhtml'" at Book (MZItmspBookPackage)
Following is a "specific" fix, but the idea of the fix will help you with your specifics too.
I tried for 17 days to upload a book that looked and worked perfectly in iPAD via Preview.
After many discussions with Apple, who to their credit stayed with me over 2-3 days, I decided to play a hunch.
I went into a duplicated copy of the book and on every page, (because the error message was not telling the whole story), looked for what InDesign would call "Overset Text."
Now... the "flaw" in iBOOK Author (hint) is that it won't advise you of this "overset text" as does InDesign.
And to compound the matter, the exported ePUB document WORKS in iPAD Preview.
See Screenshots from InDesign:
Okay... Couldn't add it but it is a Warning Box that says there is overset text. (Characters which exceed the text box.)
Nevertheless, I played this hunch, and sure enough found a few boxes with the + in them. In other words I clicked on EVERY text holder and every text block in the entire document.
Where I found + signs, I simply deleted some carriage returns from the iBOOK file... (please note… carriage returns and literally empty spaces that caused the overset text) and then erased all previous copies of the Music to Picture Book on my hard drive, iTUNES and iPAD.
The result? A "text-book" upload with no snags! As my Son would say… "Victory!"
So, first make sure that you are using only PNGs, Jpegs and Movie files to iBook Specs. Then... make sure there are no overset text boxes, which you must do manually.
Enjoy & Godspeed!
Steve
Stephen Melillo, Composer
STORMWORKS®
209 Spinnaker Run
Smithfield, VA 23430-5623
USA
v/f 757-356-1928
stormworld.com
“History is a vast early warning system.” Norman Cousins, editor and author (1915-1990)
"This will be our reply to violence: to make music more intensely, more beautifully, more devotedly than ever before." Leonard Bernstein
“If you have a chance to help someone, and you don’t, you are wasting your time on this earth.” Roberto Clemente

How do I make one (and only one) device use my Apple ID and iCloud account?

How do I make one (and only one) device use my Apple ID and iCloud account? I currently have an iPad mini, iPhone 5, and MacBook pro attached to my apple accounts, but I want only my iPhone 5 to be assosiated with either one. Whenever I use any of the three devices, I get a notification on the other two telling me that these devices are now using these accounts from these services, etc. and I want these notifications to stop, along with the devices using to them. How do I do this? I completely reset the iPad mini so I don't know how I'm still getting notifications from it, and I deleted and signed of of all of my accounts everywhere I could find on my Mac. So, to restate exactly what I want to do, I want ONLY my iPhone 5 to use ANY of my Apple/iCloud accounts and ONLY it can receive emails, iMessages, and FaceTime calls. Thanks!

If you want to disconect your Mac from iCloud, go to System Preferences>iCloud and click Sign Out. If you only want to stop using iCloud email, just uncheck Mail. To stop iMessage, open the Messages app, go to Messages>Preferences, click the Accounts tab, click your iCoud ID on the left-hand side, then to the right click Sign Out. To stop FaceTime, open the FaceTime app, then click "Apple ID" then click Sign Out.
On your iPad, go to Settings>iCloud and tap Delete Account (or if you only want to stop using iCloud email, turn Mail off). For FaceTime, go to Settings>FaceTime, tap the ID and sign out. For iMessage, go to Settings>Messages>Send & Receive, tap the ID and sign out.

IPhone 3GS suddenly stopped working with wifi in only one location

This is the situation. I have an iPhone 3GS and it the wifi suddenly stopped working at my house (just with the iPhone).
I have an Airport express (latest generation) and a time capsule (1st generation). All of my devices (except a PC laptop which isn't much of an issue, and the iPhone) cannot connect to it. The devices I have are as follows: Apple TV, iPod Touch, iPad 2, the "new" iPad, a macintosh computer.
However, when I move the Airport express to my work location, and plug it into the ethernet there, the iPhone works totally fine. It seems like the issue is just at my house. The Time Capsule works intermittently sometimes; random devices cannot connect to the network sometimes. The airport express seemed to fix this problem. I have read that this problem is related to the operating system "Lion" but the network was working fine for months and months after I have upgraded to lion. Sometimes both devices cease to work, and there is no internet to any devices in my home.
The network is password protected, so that removes the possibility of neighbors connecting to the network. The name of the network contains spaces and "symbols" which I have heard is an issue for PC's trying to connect to networks. Both my home and my workplace are on the same internet provider.
My questions are:
Why does the airport express work with the iPhone at my workplace and not at my house?
How many devices can a 1st gen Time Capsule handle at once?
If I buy an airport extreme, will it fix this issue?
How can I fix this?
I have restarted the device several times (both the iPhone and Time Capsule) and it still didn't fix anything.

Using the delete all content and settings option is not restoring the iPhone. Using the delete all content and settings option does exactly that - all content and settings are securely deleted except for the firmware, which is not a restore.
If you do this followed by re-installing an app via the iTunes sync process, the app settings and any data created and stored by the app will be lost. 3rd party app settings and data created and stored by a 3rd party app is not stored with the app on your iPhone and is not stored with the app or synced with the app in your iTunes library on your computer.
3rd party app settings and data created and stored by a 3rd party app is stored separately from the app on your iPhone and is included with your iPhone's backup which is updated as the first step during the iTunes sync process.
Restoring an iPhone with iTunes completely erases the iPhone first followed by the firmware being re-installed. After the firmware is re-installed, you are prompted to restore your iPhone from your iPhone's backup, which is the default selection. The other selection available is as a new iPhone. After either one, this must be followed by a sync with iTunes. If you restore from your iPhone's backup followed by re-installing an app that stores data you need to access, the data will be restored with the app. If you restore as a new iPhone or not from your iPhone's backup followed by re-installng an app, the app settings and any data created and stored by the app will not be restored with the app since you didn't restore your iPhone from your iPhone's backup where this data is stored.
If you restore your iPhone with iTunes as a new iPhone or not from your iPhone's backup with no change, you can follow this by restoring your iPhone with iTunes from your iPhone's backup to recover the 3rd party app settings and the data created and stored by the app along with all other data included with your iPhone's backup.

Problem with videos and only one album playback

Hey everyone.
I'm having two problems.First off,there's one album on my iPod that plays weird.It sounds like it's skipping,but not like what I'm seeing a lot of you having problems with when it goes to the next song instead of finishing the current one.Mine sounds like a CD skipping,only it's constant and all throughout the song and sounds horrible,it ruins the song.It only does it with one album though,and it's my favorite album by my favorite band,so I'm kinda bummed.I initially had three songs on this album that I brought over from Windows Media Player after uploading it onto the from my CD about two years before I got the iPod.I later added a few more and they do the same thing.I'm wondering if it's a problem with the licensing,since it's only this album,because that's the same way I got most of my other songs and they're fine.I tried deleting them and re-uploading them from the CD,but that didn't help.Tried converting the file to AAC;that didn't help either.I'm utterly befuddled.
The second question is that I've got two videos I downloaded from Limewire that I converted to iPod format and everything you're supposed to do,but I can only get the video and not the audio.My video podcasts work fine,it's just these two I'm having a problem with.Any help would be greatly appreciated.

On the second question...
If the videos are multiplexed MPEG files then the audio and the video are muxed onto the same track. QuickTime, and therefore any application that uses QT like iTunes, the iPod, iMovie (Mac app), etc. expect two separate tracks, one video and one audio. So when you play these muxed files, the video is played and the audio is not heard.
So you need to do a conversion on the file first. MPEG Streamclip is a popular one that comes in both Mac and Windows versions and is known to "repair" this problem.
See this other link for other applications that might be able to do the same thing. But your root cause is the muxed MPEG files.
GUIDES TO: Converting Video for iPod - Mac & Window
http://forums.ilounge.com/showthread.php?s=&threadid=123067
Patrick

Program Help, working with spaces and only letters

I'm writing a program that takes an input string and gets the length and/or gets the number of vowels and consonants in the string. I've gotten it working except for consideration of spaces (which are allowed) and error checking for input other than letters. Here is what I've got so far. ANY suggestions would be greatly appreciated. Thank You
import java.io.*;
import javax.swing.*;
import java.awt.*;
import java.awt.event.*;
import java.util.*;
public class LetterStringManip extends JFrame
{//declaring variables
     private JLabel stringOfLettersL, lengthL, lengthRL, vowelsL, vowelsRL, consonantsL, consonantsRL;
       private JTextField stringOfLettersTF;
       private JButton lengthB,vowelB, quitB;
       private LengthButtonHandler lbHandler;
       private VowelButtonHandler vbHandler;
       private QuitButtonHandler qbHandler;
       private static final int WIDTH = 750;
       private static final int HEIGHT = 150;
       public LetterStringManip()
       {// setting up GUI window with buttons
           stringOfLettersL = new JLabel("Enter a String of Letters", SwingConstants.CENTER);
               lengthL = new JLabel("Length of String: ", SwingConstants.CENTER);
               lengthRL = new JLabel("", SwingConstants.LEFT);
               vowelsL = new JLabel("Number of Vowels: ", SwingConstants.CENTER);
               vowelsRL = new JLabel("", SwingConstants.LEFT);
               consonantsL = new JLabel("Number of Consonats: ", SwingConstants.CENTER);
               consonantsRL = new JLabel("", SwingConstants.LEFT);
               stringOfLettersTF = new JTextField(15);
               lengthB = new JButton("Length");
               lbHandler = new LengthButtonHandler();
               lengthB.addActionListener(lbHandler);
               vowelB = new JButton("Vowels");
               vbHandler = new VowelButtonHandler();
               vowelB.addActionListener(vbHandler);
               quitB = new JButton("Quit");
               qbHandler = new QuitButtonHandler();
               quitB.addActionListener(qbHandler);
               setTitle("String Of Letters");//Window title
               Container pane = getContentPane();
               pane.setLayout(new GridLayout(3,4)); //Window layout
               pane.add(stringOfLettersL);
               pane.add(stringOfLettersTF);
               pane.add(lengthL);
               pane.add(lengthRL);
               pane.add(vowelsL);
               pane.add(vowelsRL);
               pane.add(consonantsL);
               pane.add(consonantsRL);
               pane.add(lengthB);
               pane.add(vowelB);
               pane.add(quitB);
               setSize(WIDTH, HEIGHT);
               setVisible(true);
               setDefaultCloseOperation(EXIT_ON_CLOSE);
       }//closes public LetterStringManip()
       private class LengthButtonHandler implements ActionListener
           public void actionPerformed(ActionEvent e)//Length Button is clicked, getLength() method is performed
                  getLength();
               }//closes public void actionPerformed(ActionEvent e)
       }//closes private class LengthButtonHandler implements ActionListener
       private class VowelButtonHandler implements ActionListener
           public void actionPerformed(ActionEvent e)//Vowels Button is clicked, getVowels() method is performed
                  getVowels();
               }//closes public void actionPerformed(ActionEvent e)
       }//closes private class VowelButtonHandler implements ActionListener
       private class QuitButtonHandler implements ActionListener//Quit Buttton is pressed
           public void actionPerformed(ActionEvent e)
                   System.exit(0);
               }//closes public void actionPerformed(ActionEvent e)
       }//closes private class QuitButtonHandler implements ActionListener
                 public void getLength()//gets the length of the string
                   String letString = (stringOfLettersTF.getText());
                   String lengthString;
             int length;
                     length = letString.length();
                     lengthString = Integer.toString(length);
                     lengthRL.setText(lengthString);
                }//closes public void getLength()
                 public void getVowels()//gets the number of vowels in the string
             String letString = (stringOfLettersTF.getText());
                   String vowString;
                     String conString;
             int countVow = 0;
                     int countCon = 0;
                     int i;
                     int length = letString.length();
                     char[] letter = new char[length];
             for (i = 0; i < letString.length(); i++)
                 letter[i] = letString.charAt(i);
                 if (letter=='a' || letter[i]=='e' || letter[i]=='i' || letter[i]=='o' || letter[i]=='u')
countVow++;
                    }//closes for
                    countCon = letString.length() - countVow;
vowString = Integer.toString(countVow);
                    conString = Integer.toString(countCon);
                    vowelsRL.setText(vowString);
                    consonantsRL.setText(conString);
               }//closes public void getVowels()
     public static void main(String[] args)
     LetterStringManip stringObject = new LetterStringManip();
     }// closes public static void main(String[] args)
}//closes public class LetterStringManip extends JFrame

OK, per the instructions above: I will re-post my code that I have now. I have dealt with the space not being counted now, I only need to figure out how to validate my input so that only letters are allowed. If anyone has any suggestions, or can help me out in any way, it'd be great. The suggestions with creating word and sentence objects is still a little beyond what we have gone over thus far in my Java course, I feel like I can almost grasp it to code it, but end up getting really confused. anyways, hear is my 'crude' code so far:
                 public void getLength()
                   String letString = (stringOfLettersTF.getText());
                   String lengthString;
                      int finalLength;
                      int countSpace = 0;
                            int length = letString.length();
                   char[] letter = new char[length];
                    int i;
                             for (i = 0; i < letString.length(); i++)
                                letter[i] = letString.charAt(i);
                                if (letter==' ')
countSpace++;
          finalLength = length - countSpace;
               lengthString = Integer.toString(finalLength);
               lengthRL.setText(lengthString);
               public void getVowels()
String letString = (stringOfLettersTF.getText());
               String vowString;
               String conString;
int countVow = 0;
               int countCon = 0;
               int countSpace = 0;
               int i;
               int length = letString.length();
               char[] letter = new char[length];
for (i = 0; i < letString.length(); i++)
letter[i] = letString.charAt(i);
if (letter[i]=='a' || letter[i]=='e' || letter[i]=='i' || letter[i]=='o' || letter[i]=='u')
countVow++;
               if (letter[i]==' ')
countSpace++;
               countCon = (letString.length() - countVow) - countSpace;
vowString = Integer.toString(countVow);
               conString = Integer.toString(countCon);
               vowelsRL.setText(vowString);
               consonantsRL.setText(conString);

MSI Z77A G45 not detecting Sapphire HD 7950 , only integrated graphic works

First of all - sorry for my poor english,
I've build my setup today.
MSI Z77A G45
i5 3570k with Macho Hr 02
Sapphire HD 7950 Vapor-X
2x4 GB Corsair Low Profile 1600
XFX Core 550W
The problem is MOBO is not dectecting my HD7950 Sapphire when connect to HD7950 HDMI out (using SONY Bravia as display) It works only with integrated graphic on MOBO hdmi out. I've installed Win7 64-bit. System boots fine but only on i5 graphic.
I'm using nearest CPU PCIe port. Unfortunately can't try plug HD7950 in with other PCIe port, Radeon won't fit in case I own (Fractal Core 3000 usb 3.0)
BIOS version 2.9
Need your help

Has the VGA been tested in another machine to verify it works? Do you have access to other VGA's you can test in the primary graphics PCI-E 16X33 slot? If nothing works, then it can be a troubleshooting extravaganza! First recommendation would be to test outside the case on a plain piece of cardboard or untreated wood surface, barebones configuration. Inspect the case for any errant standoffs that may be shorting/grounding the PCI-E slot. The primary graphics PCI-E slot not working can also be caused by a pin problem in the CPU socket. A bright light and magnifier will be needed for socket pin inspection.

I have an email account causes the machine to hang up after being in use for a day. It only occurs on my Macbook Pro and only one particular account. The problem account works fine on my iMac and Windows Machines. Any ideas what is causing this?

I have an email account causes the machine to hang up after being in use for a day. It only occurs on my Macbook Pro and only one particular account. The problem account works fine on my iMac and Windows Machines. I have been to the local Genius bar and through trial and error we have determined that Mail is working ok but somehow the account is causing the problem. I have used this account for years. Any ideas what is causing this?

No idea why, but one thing you may try if you have the time, is create a new user, and set up the problem mail account in the new user space. See if it causes your MBP to hang as well. That will tell you if it is something wrong with your main User, or something wrong with MBP.
Assuming this works, I'd nuke the problem account in your main user space, re-start, and reinititate the account and see if that helps.
Depening on how many email accounts you have setup, it may be necessary to nuke the whole Mail folder in your User/Library.... Hard way to get it to work, but just my idea.

HT5622 Have Family Mobile with 2 phones and only one Apple ID can all be controlled by the main phone?

Have Family Mobile with 2 phones and only one Apple ID can all be controlled by the main phone?

angiefromaustin wrote:
Yes I know the password for Apple ID.
Then there should be no issue for you.
angiefromaustin wrote:
I do not know the password to get onto the 3G phone to make changes or update apps etc.
Then there is more than one Apple ID involved.... Or a Restrictions Passcode has been set.
angiefromaustin wrote:
2 phones and only one Apple ID
Then what do you mean by this ?

I get a dialog box with a copy of firefox is open and only one copy of firefox can be open at one time.

I get a dialog box with the following: "a copy of firefox is open and only one copy of firefox can be opened at one time."
I do not see where firefox is open.
How do get back into firefox so that i can read the links that are in my emails?
Thank you.

Sometimes when FF is closing, not all of it shuts down properly.
On Windows, start the '''Task Manager''' (Other systems may have
different names and / or commands). Select '''Processes'''.
Look down the list for Firefox. Right click and select '''End Task'''.
If this problem keeps coming up, ask for more help.

HT4060 iPad will not charge if hooked by USB to pc or plugged into wall. How do I know if the problem is with iPad, cable or power adapter. I have a 12, 10 and 5W adapters no success with any. Only one lightening cable so can't swap cables.

iPad will not charge if hooked by USB to pc or plugged into wall. How do I know if the problem is with iPad, cable or power adapter. I have a 12, 10 and 5W adapters no success with any. Only one lightening cable so can't swap cables.

I'm sorry but this is too funny to pass up.

How can I order an iphone 6 and pick it up from one of the apple stores in London. It doesn't work with reserve and pick up because the 64 gb is never in stock.

How can I order an iphone 6 and pick it up from one of the apple stores in London??? It doesn't work with reserve and pick up because the 64 gb is never in stock.

Thank you for replying. Yes I deleted the old email address..

Why not to be unlocked iPhone working with GSM and CDMA/LTE in one device?

why not to be unlocked iPhone working with GSM and CDMA/LTE in one device?

I'll explain, does Verizon unlocked iPhone 5s work with CDMA networks (with SIM or without SIM), and if I travlled to another country that provide GSM operators, does the phone will work with GSM SIM normally?

Why is my airportxpr only working with Itunes and not with another music program

why is my airportxpr only working with Itunes and not with another music program??
I can not select/see other outputs in my sound selector.

You have not indicated which OS or which music program you have so I have listed a program called Airfoil to try for both Windows and Mac - it may work for you
for Windows - http://rogueamoeba.com/airfoil/windows/
for Mac - http://rogueamoeba.com/airfoil/mac/

Z77A-G45: XMP works with one and only one ram stick.

Similar Messages

Maybe you are looking for