Z77A-GD65 and SSD Crucial M4 512 gb doesn't recognize on boot

Hi all, i bought a SSD crucial M4 512 gb and connected to my Z77A-GD65, i set it on bios as AHCI mode and have the lasted firmware of my Z77A-GD65 vers. 10.5 and cricual m4 lasted firmware 000F.
when i connect the power cord and start my pc, on boot SSD not recognize, boot hangs on A2 status for 10 seconds, then boot without recognize M4, if i push reset button, no way to recognize.
the only way to work, is to power off pc, leave the power cord and reconnect immediatly and power up the pc, then on boot M4 will recognize perfectly, what is it this problem? i search on internet and i found that other have the same unsolved problem with other mainboard, not with MSI Mb, MSi can help me?, this is my system:
PSU: Corsair silent pro gold edition 600W
MB: Z77A-GD65 lasted bios update 10.5
CPU: I5-3750K
SSD: Crucial M4 512 gb with lasted firmware 000F
RAM: 8gb (4gb x 2) Corsair Vengeance DDR3 1600 cas 9
VIDEO CARD: Gainward GTX 670 phantom
S.O: Windows 7 X64 ultimate
mouse: Razer Deathadder 3.5 G
Keyboard; Thermaltake TT esport meka G unit.
bye!

Quote from: xmad on 25-September-12, 21:01:07
Have you tried updating the firmware of the ssd?
Also, try the newest bios for the z77 as well.
>>Use the MSI HQ Forum USB flasher<<
https://forum-en.msi.com/index.php?topic=158257.50
Hi, yes i've updated my crucial M4 with the lasted firmware 000F, and i try to use MSI lasted beta bios E7751IMS.A6E for my Z77a-gd65 as you suggest, but the problem remain ...
i try to make a post about it on Crucial's forum ... i want to see what Crucial answers! ......
thank you for your interest !

Similar Messages

Z77A-GD65 and front panel audio problem !!

I have a Z77A-GD65 and a case CM 690 II advanced window, and i connected the front panel audio correctly in the right port, and when i plug my headphones in the front audio jack, there is no sound !!!
Please help me !!

Quote from: CalinTM on 11-May-12, 16:25:29
Ok, i've did this thing, now works, but the sound sounds only in the right side of the headphones, and the sound is very very slow....
which of the 2 audio header plugs did you connect to the mother board ac97 or HDaudio?
have you connected the headphones to the rear pannel connector of the motherboard to see if its better?

My iPod will not charge though it is turned on. and I've tried multiple adapters and computer usb. My computer doesn't recognize it either.

I've tried multiple adapters and computer usb. My computer doesn't recognize it either.

Try:
iPod touch: Hardware troubleshooting

I have firefox os 19 and silverlight 5.1 but firefox doesn't recognize it but silverlight works fine in safari what can i do?

I have firefox OS x 19 and silverlight 5.1 but firefox doesn't recognize it but silverlight works fine in safari what else can i do?

Application
User Agent: Mozilla/5.0 (Macintosh; Intel Mac OS X 10_7_5) AppleWebKit/536.28.10 (KHTML, like Gecko) Version/6.0.3 Safari/536.28.10
Ok, how's this? and flashback isn't installed, what else?

Z77a-gd65 and evga 660ti pci question

Hey folks,
I have been updating/rebuilding a system and have gone with a z77a-gd65 MB with the evga 660ti graphics card. My question is that when booting on the initial splash screen I can see that the system is using PCI 2.0 instead of PCI 3.0, is there something in the BIOS that I missed?
What are the main benefits of PCI3.0 over PCI2.0.
Rgds

Flash the bios with the attached archive. (Full release version A70 + ME flash)
>>Use the MSI HQ Forum USB flasher<<
Use option 1 and point it at the compressed archive and it will prepare the usb stick for flashing.
When complete, do a full cmos clear, then install the most recent ME 8 Drivers:
http://www.msi.com/product/mb/Z77A-GD65.html#/?div=Driver&os=Win7%2064

Z77A-GD65 and Radeon R9 290 multi GPU problem

Hi
I am trying to setup four R9290 GPUs on the Z77A-GD65 board and for the life of me cannot get it to work. Using Windows 7 64bit with 8GB memory. I have tried installing the cards from the CPU end and backwards. Using the latest AMD drivers (13.12). Using 1x to 16x riser cables not powered.
I think the problem is either not enough power on the PCIE bus or Crossfire is not working.
Can anyone offer any help please?
Thanks

Quote
Only team members may post here, or those willing to join.
Are you joining the Red Rockets? If not, this thread is in the wrong part of the forum. The mainboard is only rated and certified to run a total of 3 AMD graphics cards in Crossfire. It also depends on the CPU used. With a Sandy Bridge, only a maximum of 2 graphics cards can be used, 3 with an Ivy Bridge.
Quote
I think the problem is either not enough power on the PCIE bus or Crossfire is not working.
Nope! Only 16 PCI-E lanes in the processor. If you want 4 GPU's, get a pair of dual GPU nVidia graphics cards.
Allocation with 3 graphics cards is 8X 4X 4X for a total of all 16 available lanes.

Z77A-GD65 and frontal USB 3.0 randomly disconnect

Hi i use on my case Enermax Hoplite ST the front USB 3.0 port that have a 20 pin usb 3.0 header cable to connect on my Z77A-GD65 MB, i use this port with external usb 3.0 feed powered enclosure hard-disk Samsung F3 - 3,5 " 1TB SATA for back up .... randomly, without any reason, enclosure disconnect , why? i haven't this problem if i connect the enclosure on frontal usb 2.0 and even if i connect to REAR USB 3.0 port .... only frontal USB 3.0 have this problem ... why? any idea? maybe frontal USB 3.0 have less ampacity of rear USB 3.0, than disconnect my enclosure?
bye

Could be a problem with your Enermax case's front cabling. If you have another USB 3 front or rear connection bracket, then you could plug that into the USB 3 header to test.
Else you will have to check with MSI technical what the max amps are on the USB 3 header. Mine works just fine with a portable 500GB external portable drive.

Z77A-GD65 and fan controls

I'm considering buying MSI Z77A-GD65. It has the better Realktek audio chip and Intel LAN chip. But I need to know what kind of fan controls it has:
1. What kind of fan headers it has? (PWM, voltage controlled, how many?)
2. What BIOS settings it has for fans? Ie. What is the minimum duty cycle for manual PWM fan control? What other settings and modes?
3. Are there any plans to improve the BIOS fan controls in later BIOS updates?
This is essential thing for a silent computer. If MSI is good enough, I'll get it. Otherwise I have to consider Intel DZ77BH-55K.
PS. I'm only interested in BIOS settings, not possible Windows software settings. I use both Windows and Linux so everything must be controlled from BIOS.

Hi
I just bought that exact board for the same reasons you are considering it. The only Z77 board in that price range with both Intel nic and the better realtek Audio chip
The only thing this board is lacking is exactly fan control. But i knew this before i bought board. You have the standard CPU fan Auto setting, but that's pretty much it. (at least what i have found)
I invested a few extra euros in Silent case fans. For CPU i use the Corsair H80 that has its own fan control anyway.
So i ended up with a relatively silent PC anyway.
The board is brilliant for OC, and in general a very good board.

My iPod Classic 160 is in disc mode and won't turn off, itunes doesn't recognize it - ¿how can I make it work again?

My iPod Classic 160 is in disc mode. I responds to nothing. iTunes doesn't recognize it. It doesn't sync. I've tried to restore and got error 1429. Now it just stays in disc mode and won't turn off. I'm keeping it connected to the charger so it doesn't go dead. Is there anything I can do to resurrect my pod?

To get out of disk mode do a iPod Hard Reset.
Toggle the Hold switch till you dont see the red mark.
Press Menu and Center buttons simultaneously for about 10 secs till the Apple logo comes ON then release the buttons
Select your preferred language.
See this Apple support Article on the 5Rs.
http://www.apple.com/support/ipod/five_rs/classic/
If you try to restore and get a1429 error message, read this Apple Support Article
http://support.apple.com/kb/TS1372
Good Luck!

My laptop has windows 7 64bit and when i downloaded itunes it doesn't recognize my 3gs or my Ipod touch, but will charge them both

Recently purchased a laptop, came with windows 7 64bit, downloaded itunes and tried to sync both the 3gs and Ipod touch, itunes doesn't recognize either. The computer doesn't show the devices on the device manager but I am able to charge them both from the usb ports. Tried uninstall and reinstall itunes and rebooting the apple mobile device support. Need suggestions

If the above fails, try this
https://discussions.apple.com/thread/5546702

What can I do when I try to access a URL and get the message "MAC OSX doesn't recognize internet addresses starting with "c:"?

I recently tried to download a pdf file from a website in the UK. Up popped a message saying the website could not be accessed, followed by this message: "MAC OSX doesn't recognize internet addresses starting with "c:". I was able to access the website easily (its domain was "www") and the page listing the pdfs, but could not download a pdf. Of course," c:" appears not to be a valid domain name, but why would anyone use "c:" in place of a domain name in their URL? And what can I do about the problem? I'm using Snow Leopard 10.6.8 and Safari 5.1.10, but also have Firefox and Chrome loaded. Thanks.

An address starting with c: wouldn't be any kind of domain name. C: is the drive lettering system DOS and and later uses. By default, A: and B: are reserved for your first and second floppy disk drive. All hard drives are then named C: through Z:, if you have that many. C: is normally your startup disk.
Anyway, their PDF file is incorrectly linked to a file directly on the C: drive of someone's computer. It's not going to work no matter what you do.

Iphone in recovery mode and DFU mode but PC still doesn't recognize device

HELP! My iphone 4 just keeps blinking the apple logo for hours! I tried the recovery mode and DFU mode, the first time went well, but it started to blink again after I restored it. Now I'm doing the same steps going to recovery mode and DFU mode, they work on the phone but for some reason, my laptop doesn't recognize any device connected. I tried everything on the internet and still wont work. WHAT CAN I DO???
by the way, Mine is windows 7.

it needs repair
Peace, Clyde

Z77A-GD65 and Intel Rapid Start -suddently a problem ?

Greetings.
Have been using Fast Boot with my mobo since I learned how to do it, and it has worked flawless. But suddently something annoying is begun.
When power on with IRS active, it starts to load with black screen, but after about 5 seconds, the hdd-led turns off, and my monitor goes to sleepmode (no signal from graphic-card). It then just hold there for 15-25 seconds, then wake on again and boot to windows 7.
At first I had an access-code to log into windows, and with this active the pause 15-25 seconds is after the screen to type password is on, but BEFORE I can actually type anything.
What can cause this error?
On a secondary SSD I have installed Windows 8, incl. Intel Rapid Start, and the error is ALSO there! So my guess is, that it is something in the BIOS, but I have not changed anything in BIOS (just the bootorder to start from either SSD1 or SSD2 (Win7 or Win8).
Please help if you can. I have braged about my 10 seconds start to a friend, but when I showed it to him, I had this silly error, so instead of 10 seconds it took 33 seconds. It was so embarrassing for me

Quote from: xmad on 11-December-12, 04:20:20
http://download.intel.com/support/motherboards/desktop/sb/rapid_start_technology_user_guide_v11.pdf
Is the hibernation partition large enough? (= to the amount of ram you have installed)
Since this worked for awhile, what changed?
Did you install some new drivers, new bios or new hardware?
Might want to update the firmware of the ssd's
If you wish, you can try the newest bios: >>Beta BIOSes<< When used with the forum flash tool, it will update the me versions. Aftwards, you will need to re-install the me drivers.
Yes, it has worked, so partitions is OK. The strange thing is, that I have not changed drivers (oh yes, a driver for my Nvidia graphic card, but that was after the error began, and only in Windows 7), no new BIOS settings I can remember of, no new hardware. It just started this about a week ago without I have changed anything. I have tried to reset BIOS, and load an earlier setup-profile of BIOS (my OC-settings), but that did not help.
Oh, BTW, I can't install Microsoft SDK tool as seen here:
http://www.sevenforums.com/tutorials/177443-gathering-startup-shutdown-sleep-hibernate-reboot-trace.html
It begin install, but suddently under install, it starts to uninstall again without any error. I have an idea, that this tool might show me what is going on when starting IRS, but that might be a mistake?

Z77A-GD65 and Intel ME bios upgrade error ...

When uploading computer bios to reset !
There is now no ME N/A
BIOS 10.11
How to upload ME ?

Quote from: Svet on 08-November-13, 02:17:25
you can't update the ME by this way
did you pickup update: BIOS + ME , option?
YES !
only bios upgrade - restart
bios and ME - restart
https://plus.google.com/115202106830499885914/posts/diA6bUppHJY

My ipod touch is disabled and won't turn off, itunes doesn't recognize the device and i can't see the serial number on the back

My NOSY (now ex) husband did something to my ipod touch and it is now disabled. It was dead and I charged it and NOW the sucker won't turn off. When I connect to itunes i see a message that says i have to UNLOCK it with a passcode. I tried to get apple support but they want my serial number. Well...the ipod wont turn on!!! I've had it at least 6 years and have moved and I can't find my paperwork and WHO can read that serial number on the back? I know its kind of outdated (third generation, I believe)but its mine, I love it and it has ALL my music on it.

Disabled
Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Wrong passcode results in red disabled screen
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: Back up and restore your iOS device with iCloud or iTunes
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store
If problem what happens or does not happen and when in the instructions? When you successfully get the iPod in recovery mode and connect to computer iTunes should say it found an iPod in recovery mode.

Z77A-GD65 and SSD Crucial M4 512 gb doesn't recognize on boot

Similar Messages

Maybe you are looking for