Z77A-GD65 primary bios corruped and can't restore it!!

Hi guys, last weekend was happened a very strange thing ... i used my pc with MSI mb Z77A-GD65 regulary Saturday and power off without any problem,
Yesterday i power on my PC and doesn't work, MB starts with coolers but no P.O.S.T sound error and only black screen, i try to reset bios .. nothing, i switch to secondary bios and immediatly works!
Then pc runs fine.
So I re-flash the primary bios and the procedure ends without no problem, i re-switch to primary bios and again not works like the beginning ... i try other re-flash to primary bios but same story!
So finaly Pc works only if i switch to secondary bios, primary bios not work though i re-flashed bios .......what's up? is primary bios flash eprom damage... without any apparent problem?
All of 2 bios primary and secondary have the lasted MSi Z77A-GD65 Bios ver. 10.8

Quote from: Noway77 on 16-July-13, 17:03:52
Hi, did you try flashing with M-flash Multibios flash tool under Bios?
If it doesn't work with 10.8 you need to downgrade it to 10.5 using MSI HQ USB BIOS Flash Tool, dont use the M-flash when downgrading Bios.
Then after you have 10.5 Bios use the Multibios option under your Bios, and it should work fine.
Hi, thanks for reply, i try every version of bios, i try to flash by Multibios flash tool under Bios, and by standard procudure, boot with 2nd bios with bootdisk,, than switch to primary bios and flash under dos..no way !!, primary bios don't want to boot up!
What is strange is every time i try to update primary bios with M-flash Multibios flash tool and by dos command, only secondary bios updated not the primary one!!... its seems that primary bios flash memory no longer exists .. i think that primary bios flash memory has been damaged for incomprehensible fact ...

Similar Messages

Z77A-GD65 flash bios & ME firmware

Hi,
ive z77a-gd65, with bios v10.11 but with old ME Firmware.
Please tell me how can i update that ME Firmware, using MSI Flash tool?
xmad writes in 1st post smth about that i need to ask for a proper file to write?
Im asking because i dont want to brick the board.
I know how to update bios but i didn't know that i need to flash ME firmware too, and how to do this?
Thanks

there is instructions:
https://forum-en.msi.com/index.php?topic=163874.msg1267801#msg1267801

Can not update error 1602 and can not restore error 1604 what is the solution

Have a IPod touch 4, can't update (error 1602) and can't restore (error 1604) any solution?

try this support article.

I get a black white sceen and can't restore

I get blank white screen and can't restore an ipod.

What happens when you try to restore?
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

When I statred iTunes match I lost some of my music and all my playlists, has anyone had this problem? And can I restore it?

When I statred iTunes match I lost some of my music and all my playlists, has anyone had this problem? And can I restore it?

Restore your media from the backup of the computer created prior to restoring the computer.
You did create a backup, correct? Not doing so would be extremely unintelligent.
iOS devices are NOT backup devices.

HT1553 I want to do a clean install of Mountain Lion. Can I do this without a DVD version of the OS, and can I restore only specific things like iPhoto and iTunes libraries from Time Machine backup.

I want to do a clean install of Mountain Lion. Can I do this without a DVD version of the OS, and can I restore only specific things like iPhoto and iTunes libraries from Time Machine backup.

Mountain Lion is only available as a download, so there is no DVD to purchase. What you can do is download ML and then stop it from installing as soon as it's on your drive. From there you can make your own bootable ML flash drive.
When your purchase and download Mountain Lion, it will end up in the Applications folder and automatically want to install. Press Command+Q to stop the install and exit. The installer will remain on the hard drive.
1) Right click on the installer and choose "Show Package Contents".
2) A folder will open on the desktop. Drill down to Contents > SharedSupport and double click the disk image InstallESD.dmg to mount it on the desktop.
3) From here you can either burn a DVD, or copy the contents to a flash drive. Personally, I would strongly suggest using an 8 GB flash drive formatted as Mac OS Extended. You will be able to boot to it in about 30 seconds instead of at least 10 minutes off of a DVD, and it will install MUCH faster. Make sure the flash drive is empty, or you've copied anything off it it you need as it will need to be erased.
4) Don't just drag and drop the contents you see in the open disk image to the flash drive. It won't boot that way as it will be missing some hidden files. Open Disk Utility. You will something similar to this:
5) To accomplish the above, highlight either the flash drive's single partition (as I did), or the item at the bottom (Mac OS X Install ESD), which is what you will see with the Lion disk image mounted. It doesn't matter which one you pick. You'll then have the option to select the Restore tab towards the upper right. Drag and drop from the left column into the Source and Destination fields as shown above. If you've already erased the flash drive, you can uncheck the box. Click the Restore button.
You've just made your own bootable Mountain Lion USB Flash drive installer. Once you boot to the flash drive, run Disk Utility first to erase the drive you want Mountain Lion on, then continue with the install.
As far as restoring your iPhone and iTunes libraries, I couldn't tell you. So I wouldn't do any of the above until someone else chimes in with a way to do that after a clean install of ML.

When I switch libraries I lose the majority of the material in my main library and can only restore it by repairing the database. Can anyone tell me why this is happening and how I can resolve the problem? Thanks

When I switch libraries I "lose" the majority of the material in my main library (or at least I can't see it) and can only restore it by repairing the database. Can anyone tell me why this is happening and how I can resolve the problem? Thanks

I seem to have found a way around it. Rather than switching libraries by going into files/switch libraries I used Aperture Preferences to change them. I've done it a couple of times and it appears to work OK.
That is an interesting finding. It suggests, that your "Preferences" file "com.apple.Aperture.plist" may have been corrupted and you fixed it this way. Can you now switch between libraries the usual way? If not, I'd try to remove the "preferences" file from the user library to the Desktop and relaunch Aperture.
The Aperture 3: Troubleshooting Basics:http://support.apple.com/kb/HT3805
describe how to remove the user preferences.

HT1222 i lost all my apps and can not restore it before the update can somebody help me!! cant back up from itunes nor icloud and my iphone isnt jailbroken either wth!

ive just updated my iphone it automatcially did it via itunes on my pc and now i've lost all my apps and can not restore from icloud and itunes sync and my apple id isnt accepting my password what on earth is happening im tearing my hair out!!! stupid update

Can somebody help me with this ??

Z77A-GD65 Multiple BIOS Issues - B4 Hang, Splash Screen Blinking

Back in November 2012, I built a home server with a Z77A-GD65. Lately, I've noticed some strange things happening that I've been trying to research but to no avail.
First off, I get the B4 code hang-up whenever I'm booting. This doesn't matter if it's a cold boot or a reboot, it hangs on B4 for about 10-15 seconds, flashes 92 really quick, and then goes to A2 which it stays for another 5 or so seconds. After that I get the MSI splash screen for about 1 second, then it blinks 5 times. After that it goes into Windows just fine.
The blinking is a new issue, the B4 hang is not. I've read from multiple posts that this is a USB issue. When I disable USB legacy support, the issue goes away, but of course then I can't have legacy support. I have yet to figure out what exact device is causing it. In the process of trying to figure this out, I updated BIOS to A.A0. After updating to this version of BIOS the splash screen blinks 5 times before going to the "Starting Windows" splash screen. This is a more difficult issue to figure out why it's doing this because if you search for "BIOS" and "flash" or "flashes" or "flashing", you typically get results for flashing your BIOS. Hence, why I'm using the term "blinking". But even then I can't really find a solution out there.
I also happened to see that the website for the Z77A-GD65 is showing a newer BIOS version, but I'm unable to flash this (at least using M-Flash). I threw it on a USB, re-enabled USB legacy and whenever I click on it to install, the BIOS screen hard locks. The screen just freezes exactly where it's at in the BIOS and the mouse is dead. However, I can CTRL+ALT+DEL on the keyboard and it will reboot the system so I don't need to power cycle the computer. Not sure why this is happening either. Perhaps I need to flash this a different way? Maybe I don't need to flash this at all?
I could really use some input here on why this is happening.
As for the specs on my system, they're as follows:
i7-3770K overclocked to 4.2 Ghz by using the Turbo Mode in BIOS
32GB Komputerbay DDR3 PC3-12800 1600MHz DIMM with Low Profile Blue Heatspreaders Quad Channel RAM | 9-9-9-24 XMP ready
AMD PowerColor 7870 Myst Edition GPU - currently not overclocked although overclocking this doesn't seem to affect any issues
2 - 128 GB Corsair SATA III SSD - one runs the OS, the other I use to load games from
2 - 500 GB Seagate Barracuda 7200 RPM Sata II HDD's mirrored via Windows 7
1 - 750 GB Seagate Barracude 7200 RPM Sata II HDD
1 - 1 TB Western Digital MyBook USB 2.0 external
2 - 3 TB Seagate USB 3.0 external
ASUS DVD Burner - not sure which one, it's a cheapy $20 from Newegg
1 - PCI USB 3.0 expansion card
Antec TruePower New TP-550 Modular 550W Continuous Power ATX12V V2.3 / EPS12V V2.91 SLI Certified CrossFire Ready 80 PLUS BRONZE Certified Active PFC "compatible with Core i7/Core i5" Power Supply
NZXT Switch 810 gunmetal - currently have 4 fans running but plan on more, also the Switch 810 has the multi-card reader in the front with 1x SD Card, 2x USB 2.0, 2x USB 3.0
for peripherals
1 - Microsoft 360 Wireless controller adapter (legit one, not the knockoff although I had a knockoff prior to getting the real deal)
1 - Logitech Wireless USB Keyboard with Touchpad
I tried to be thorough. Thanks in advance for any help!

Quote from: PirateDog on 26-August-13, 12:45:18
Probably a USB device problem.
This is a candidate, as well as mouse and keyboard. Disconnect USB devices one at a time to find the culprit.
A lot of devices running. PSU a +12V single rail or is it multi rail? A rail going to the graphics or components may not be enough amps. My best guess is the card reader.
For UEFI/BIOS flashing, select your mainboard here and use the forum flash method;
I'll definitely try unplugging some of these USB devices to see if that helps with the B4 hang issue.
As for the PSU, according to the description for it on Newegg: "Four industry-leading independent +12v rails are provided for more stable and safer power output." It has two rails going to the GPU. The GPU is a new addition to the system and so I wasn't running it until recently. The issues were occurring beforehand, but you're right that this PSU is underpowered for the rig considering PowerColor recommends a minimum of 500w. I'm going to be buying a larger capacity one sometime in the very near future. Any recommendations on good modular PSU's? What's a good way to tell what wattage to get?
Thanks for letting me know about the forum flash method. I'll be back later when I have some results.

Z77A-GD65 + GTX780Ti = BIOS error 99

Posted this on someone elses thread, apologies:
'Im having a similar problem, i have had a Z77a-GD65 with a GTX 670 windforce X3 card working for over a year, got the GTX 780Ti last night, removed the 670 and replaced with the 780Ti, all of a sudden getting error codes, removed all graphics cards getting error code 99, stripped down to no HDD, 1 stick of different RAM no graphics (except intel 3770K onboard graphics) and still cant get past error 99.
I have tried and reset both CMOS, removed battery etc, makes no difference.
I have a 600W PSU as recommended, has this combo fried my motherboard, as replacing my GTX670 now does not fix the problem, so Im really in trouble. I only have a spare laptop so mo way to tyest any individual parts out.'
The advice was to update BIOS, Im not sure how to do that if I cant boot the machine, any ideas?

Unfortunately using onboard graphics also produces error code 99, its impossible to get to the BIOS, even with the MOBO on my desk with just CPU and RAM, still get error code 99 on the MOBO post code readout. Is there any way to bypass error codes and get to BIOS?
Something seemed fundamentally broken so I got a cheaper MSI Z77MA-G45, put it all together and everything works perfectly, even the GTX780Ti, perhaps my old MOBO just failed. Im pretty disappointed though as it was only 18 months old.

Z77A-GD65 Buggy bios Version 10.10

Hello All
I recently got this motherboard and during a bios update through MSI tool M-Flash I faced similar problems as some users reported in other post: https://forum-en.msi.com/index.php?topic=171694.0
I have made the registration on the forum to share a solution that worked out for me.
I received the board on Bios 10.0, and I installed a Core i7 2600k and 16Gb DDR3 2133Mhz on it. First I run it without any PCI-Ex VGA.
I installed Win 7 64bits Ultimate on a SSD samsung EVO 840 256GB drive without any other drive pluged to the board.
The result was awsome, loading Windows in 10 seconds.
Then i instaled my HD6950 VGA and pluged in all my HDD (2 x 2TB + 1TB +750 MB + 500 MB) and every thing worked like a charm.
Later I thought, I have a very old Bios version, perhaps there is improvements regarding satbility or performance and there was where I mess up.
I updated the Bios to 10.10 through MSI tool M-Flash, the tool finalized the update (there was a progressing bar on the screen) and reboots the system.
Guess what? The system didn't boot and was only showing the hash blinking on the up left corner of the screen.
I switch the Multibios switch to the second bios position and the system got alive again.
After some trys, I was able to boot from the USB drive from where I have installed the OS, and i notice some strange cenario, the Windows installer was able to "see" all the drives, but if I select any one to go on with the instalation, I got a message like "The Windows can not be installed on this drive because a driver is missing" I'm not sure if these were the exactly words but this was the sense of the message.
This was the way I didi it:
1- you need get a good bios file (you can boot with 2nd bios and save it to a file or you can download a diferente version in my case I got the file for 10.8 version). When you download the bios from MSI webpage you get 3 files (7750vAx.TXT, AFUD238S.EXE and E7751IMS.A80 in case of version 10.8)
2- You need to prepare a bootable USB drive with MS DOS or equivalente, for that I have used "rufus-1.4.12" software that you can download on Rufus webpage.
3- After you create the bootable USB drive with MS DOS, copy all the files you got from MSI webpage on the root directory. You can check on a diferente PC or with the other bios if every thing is ok and if the bootable USB is working properlly.
4- Select the BIOS you want to restore with Multibios switch (the phisical switch on the board). (As far as I understood, older boards allows you to boot with bios 1 and after boot you would be able to switch to bios 2 and flash it, on this borad that won't work you will flash the bios from you have booted).
5- Power on your system, entrer the bios and set options to default, save and power off the system. (this is very importante because you can flash a diferente bios with diferente options and if this options won't exists on the version you are instaling the system can hang up and mayby this could be the end for this bios - I'm guessing but is better not to try)
6- disconnect all your sata drives.
7 - Power on the system and boot from the USB drive with MS DOS
8 - Type the folowing comand "AFUD238S.EXE E7751IMS.A80 /S" and press Enter, the software will do a full flash to the bios. Don't power off the system during this procedure otherwise this bios is dead.
8 - After every thing have finished (you should see the promt on the screen C:>\), reboot your system and you should get a functional bios, justo ensure you test it first only with the OS drive and then plug the others.
Note: This board has a multibios function on the Bios that if it is turned on the system will copy the content of one bios chip to the other, BUT, as far as i understood the system wil do a comparison between both chips and will replace the older version with the new one, that in my case would be a problema because the most recente one is the faulty one.
I hope this can help any one who is facing this or similar problems.
Best Regards from Portugal.

Hello,
4th step.
Quote from: nunofilipemartins on 28-January-15, 04:26:38
4- Select the BIOS you want to restore with Multibios switch (the phisical switch on the board). (As far as I understood, older boards allows you to boot with bios 1 and after boot you would be able to switch to bios 2 and flash it, on this borad that won't work you will flash the bios from you have booted).
Best Regards

P67A-GD65 Primary BIOS Failure

Hello there.
I was playing with memory timings, and after few harmless boot hang ups I'm here...
Thanks to blue flashing LED I know my primary BIOS has failed, however, I cant repair it using secondary BIOS ( https://forum-en.msi.com/index.php?action=dlattach;topic=145084.0;attach=7527 ). EFI just hangs up when I try to save any settings.
I did clear CMOS already - no effect.
Any help much appreciated.

Quote from: Henry on 13-February-11, 08:42:22
>> Use the MSI HQ Forum USB flasher <<
After flashing (to 1.7) and reseting cmos problem is still there ;/

Z77A-GD65 - Dual BIOS Issue

Hey guys, I believe there is an issue with the Dual BIOS feature on my board.
During some OC tests and changes, I experienced the following with my board:
1. I applied OC settings which caused the PC not to boot.
2. I switched to the second BIOS and the PC didn't boot - At this point, I should have been able to boot the PC with the second BIOS but nothing happened.
3. I cleared the CMOS by removing the battery, the PC booted fine.
4. I went into one BIOS, reapplied my old OC settings and the PC booted up fine again.
5. I switched to the second BIOS again to see if it was on default, to my surprise, it had the exact same settings as the second BIOS.
6. So today I tested again, I switched to the secondary BIOS and loaded optimized defaults on it, guess what? The PC didn't boot at ALL! On defaults!
7. Switched to the second BIOS, and again, no boot.
8. Removed the Battery again, both BIOSes reset to default.
9. Reapplied my old OC settings again on one BIOS, PC booted up.
10. Switched back to the secondary BIOS = SAME SETTINGS!
At this point, I have no backup BIOS, any change I set changes it for both of them, when I move the switch all settings are completely identical.
Either I killed one of the BIOS chips and they both act as one or my board is defective and it is not switching between them.
How's this possible?!

What ever solution you choose to cure the problem you should also notify the manufacturer so they can redesign the back plate, include spacers or whatever is needed in the future. Possibly they can offer a fix for you. I'm pretty sure they would be more than willing to make a happy customer out of you.
I would use some nylon washers of some kind from a hobby shop or hardware store if it was mine provided there was enough space between the back of the MB and the case for it. Otherwise as you say trimming the back plate would be the only other way to do it.

I have locked myself out of my iPad and can not restore unless I go onto the iPad and turn off FindMyiPhone, how do I sort this out?

After installing iOS7 I was prompted to make a passcode, I did so and stupidly forgot and now continually am disabling my iPad, ways in which I have read you can sort this is restoring your iPad, however I can not restore without iTunes telling me I need to go onto the iPad and turn off FindMyiPhone! How else can I sort this? It is logged into my apple account and everything! This is an iPad 2 also ASAP help!!

Hello shanefox,
This can be done by logging in at iCloud.com and removing your device via the Find My iPhone web interface.
iCloud: Remove your device from Find My iPhone
http://support.apple.com/kb/PH2702
Cheers,
Allen

I deleted my contacts by mistake and can't restore them from time capsule

Please Help!!
I deleted around 4000 contacts by mistake with a script deleting the annoying duplicates that come with cloud syncs.
I can't restore them from my time capsule, I have read other posts and they suggest to copy the contacts folder in a back up from my time machine, Time Machine volume -> Users ->Yued1 -> Library -> Application Support -> CONTACTS, coping the folder in to my desktop and deleting the one in my computer all with out internet connection so iCloud won't cause problems, export the contacts, connect to the internet and then once connected let iCloud do its thing and then import the exported contacts, it all sounds good but when I mount my time capsule volume I get the folder backups.backupdb>Yued's Macbook Pro>(The backup folder of the date I choose)>Macintosh HD>Users>yued1 but Inside yued1 there is no Library folder, I did the command in terminal to show all files and folders, terminal accepted it relaunched finder but still won't see library, the only folder in my time capsule with library, is inside Macintosh HD but doesn't have a contacts folder inside application support.
I have OS 10.9.4 processor 2.2 GHz i7 and 4GB 1333 MHz DDR3
I don't know what time capsule I have except that is a 1TB from 2011
I really appreciate your time helping me out. thank you!

Thanks for your help,
It takes forever to go from one window to another back in time, once I get to the one I want and click restore It goes back to my desktop as it would when restoring something else but the contacts stay the same...
I do see all the deleted contacts in the snapshots, but can't restore them

Z77A-GD65 primary bios corruped and can't restore it!!

Similar Messages

Maybe you are looking for