Z77A-GD65 Problems with Ethernet (Intel 82579V) Code 10 and 55 error

it is just a day with disaster. I bought Z77A-GD65 yesterday, and now it almost driver me crazy , i have two most famous problem of the board ,the CODE10 and ERROR 55!!!
after i bought this board to home ,i spend few hour to figure out the reason why the system can not be booted.
the DIMM SLOT 3&4 of my board is malfunction,no matter what combination i use (1&3,2&3, 3&4...etc),but it works for 1 and 2(i have 4 ram sticks,all of them is fine)
i do upgrade to BIOS 10.5(thx god ,i have two computer ,otherwise i cant even do it because of following issue)
after i solve the problem by only plug in 2 ram (DIMM1&2), succeed to boot up, a new problem occurred to me ,the CODE10!
latest driver , clean system install ,cmos cleaned, does not help.
i have read this thread for code10
https://forum-en.msi.com/index.php?topic=158591.msg1167303#msg1167303
and  for error55
https://forum-en.msi.com/index.php?topic=158224.0
it seems the best way to solve it is RMA.
I notice that there is an Authorized Motherboard Repair Center (East Coast):
361 Alden Road
Markham, Ontario, L3R 3L
i live in Toronto, can i just go there and give the board to them  to fix it or i can only mail it?
If i need to mail it ,what should i do?

Code 10 means the device cannot start. You have the right driver for the Intel 82579V is shorted by either a motherboard screw or a raiser under it. The ethernet adapter has lights which light up id driver is installed (even though code 10 is in effect).
Solution: Remove 1 or 2 motherboard screws and turn the pc on. Repeat until you find out which screw caused the issue. For me it was the screw closest to the ethernet controller.
The wa i fixed it was I was used a plastic washer and I was still able to have the motherboard screw in and at the same time not get code 10 anymore and my Intel 82579V worked fine since.

Similar Messages

  • Z77A-GD65 Problems with Ethernet (Intel 82579V) Code 10

    Hi,
    on a fresh install of Windows 7 64bit i cannot make the Ethernet port on the motherboard work. It installs fine, but when i check device manager i see this message:
    This device cannot start. (Code 10)
    I downloaded the latest driver, but still no change.
    Looking in device manager, i noticed that the driver Windows had selected was Intel 82579LM, so i reinstalled the driver, and forced 82579V driver, but still no change. I assumed this must be a defect motherboard, so i rma'd it, and got a new one....with the same problem!!!
    So any ideas with to do ?

    Quote from: Warner on 11-May-12, 04:10:22
    Hello kaizerman,
    Are you in the US?
    Can you send the motherboard to me directly for analysis?
    If needed, I will replace the board for you through RMA service.
    Please email me at [email protected] but be sure to put my name in the subject field and your board model so it will come to me correctly.
    Sincerely,
    Warner
    Hi Warner
    Thanks for the reply. Unfortunately i'm not not in the US, i'm in In South Africa. Ive tried pro17 with no success... currently its showing the 82579V driver. but no still has the cannot start error code 10. I cant understand why it was working for a few days. then suddenly stopped. i made no hardware or software changes.
    regards
    Utterly perturbed 

  • Possible to update Z77A GD65 bios with latest intel raid rom?

    I was wondering how difficult it is to update the bios myself with the new intel beta rom?

    Quote from: Daffy101 on 10-June-12, 00:29:04
    I was wondering how difficult it is to update the bios myself with the new intel beta rom?
    Try this one. It's based on the e7751ims.a43 with the following updated components:
    1. intel me firmware 8.0.10.1464 (stock: 8.0.3.1427)
    2. intel raid orom 11.1.0.1413 (stock: 11.0.0.1339)
    3. sandy bridge microcode 0x28 (stock: 0x25)
    4. ivy birdge microcode 0x12 (stock: 0x10)
    I've NOT tested it because I don't have z77 motherboard but it should work fine. However I'll not be held responsible about any direct or indirect damages to (but not limited to) your board resulting from flashing and/or using this bios. USE IT AT YOUR OWN RISK!
    The checksum of the modded file e7751ims-mod1.a43 is:
    Code: [Select]
    SHA-256: f420998b3dba8a3eb68afcafeeae8297ce279d3dbd95ae88296c35d1259d4fd8
    hXXX://world-wide-web.sendspace.com/file/l539gt

  • Getting problem with safari, requires activation code and no longer opens. Restarting my devices does not help. Thie newer system the more bugs it gives us. It is getting full of bugs like this...

    MMy safari no longer works.

    What OS are you using? Can you post the error message you are getting? Try opening Safari with the shift key held down.

  • Problem with dsc shared shared variables and error 1950679023

    I'm having trouble using shared variables on my laptop PC (with Windows XP) using Labview 8.2 and DSC.   I've set up a simple project with one VI and one shared variable library.  In the VI, I have  a while loop that writes a number from a front panel control to the shared variable.  Another loop running in parallel reads the shared variable and displays to an indicator on the front panel.   The VI resides on my PC (no remote targets). This program executes just fine on my desk top PC; however I get the following error codes out of the shared variable nodes when I run the project and VI on my laptop for the write and read, respectively: ni_tagger_lv_Write 180121604 ni_tagger_lv_Read -1950679023 I've tried to manually deploy the shared variable library without success. The NI knowledge base  and other entries on this forum suggested that the Windows firewall should be disabled for a quick fix, however, the firewall was already disabled on my lap top. I didn't see any entries regarding the 180121604 error code.
    Any suggestions would be appreciated.

    The problem has mysteriously gone away.  For about the 10th time, I manually deployed the share variable library, and it started to work properly.

  • Z77A-GD65 issues with Geforce GTX 780 Video Card

    Hey Guys,
    I have a issue with a new PC build.
    I think it may be a driver or BIOS setting issue, I hope
    I bought a MSI Z77A-GD65 motherboard and below are the specs:
    - Intel Core i7-2600 CPU 3.4 Ghz
    - BIOS Version E4451IMS V10.8
    - Balistix Sport 8GB sticks (Total of 24 GB memory installed)
    - Kentek 875w power supply
    - Geforce GTX 780 Graphics Card
    My problem is with the Geforce GTX 780 video card, I installed a fresh install of Windows 7 64 bit and
    everything runs and works fine,but when i install the Geforce GTX 780 video card and install the
    drivers its all good up to this point but when i restart the computer i get this message in the device
    manager ""Windows has stopped this device because it has reported problems (code 43)"
    I have installed different versions of the driver, a few older and few newer versions with the same
    outcome.
    I tried to flash the BIOS to the latest version 10.11 but had problems with it picking up my harddrive
    after it flashed successfully. I even checked the boot up setting and it all looked good just would not
    boot up, so i had to revert back to the v10.8 BIOS version for it to work.
    I'm not sure if there is a setting in the BIOS that i need to turn on or off. I'm not familar with this BIOS,
    is there a place in it so i can see if the BIOS is picking up the video card, it has to or Windows would
    not see it right?
    I'm stumped here, do you guys know of a Geforce driver version that works well with this video card?
    I truely think the card is fine because when i install the card to the motherboard i dont get any weird
    issues until the driver is installed and Windows is restarted.
    I would greatly appreciate any help and advise that you guys can give me.
    Thanks alot

    UPDATE 
    Well i wanted to post an update on my new build issue.
    Here are my specs:
    I bought a MSI Z77A-GD65 motherboard with BIOS v10.8
    - Intel Core i7-2600 CPU 3.4 Ghz
    - BIOS Version E4451IMS V10.8 (i had a issue with the newest BIOS flash v10.11 it wouldn't detect the harddrive, could figure that one out so i went back to v10.8)
    - Balistix Sport 8GB sticks (Total of 32 GB memory installed) I first had 3 sticks so i got another 8GB stick to fill all 4 banks for total of 32 GB
    - Corsair Professional Series 860 Watt Digital ATX/EPS Modular 80 PLUS Platinum Power Supply AX860i (Bought this PS to replace the Kentek PS)
    - N780 TF 3GD5/OC (GeForce GTX 780 GAMING) (traded Geforce GTX 780 card for the MSI version of the GTX 780 card)
    OK... I got the new Corsair 860w power supply installed and i installed the new MSI GTX 780 video card with the specs above everything installed fine no problems and my son was playing the Bio Shock Infinite game on Steam and about 1 hour into the game he got a blue screen of death, says something like "to prevent damage windows is now resetting" and it turns off so fast can't read the rest of the message.
    I'm going to here in a little bit and update all device drivers with MSI Live update utility and also update the motherboard BIOS again to v10.11.
    I'm really confused here, I'm also going to take out some memory and try to run it with sticks only in slot 2 & 4 to see if it runs more stable like that, also should i update the video card to the latest driver, i know the latest is not always the greatest driver.
    I want to think you guys again for your help & time with this issue. I really dont know what else to do here, everything is new in this PC.
    Thanks

  • MOVED: Z77A-GD65 issues with Geforce GTX 780 Video Card

    This topic has been moved to Intel Core-iX boards.
    https://forum-en.msi.com/index.php?topic=177652.0

    UPDATE 
    Well i wanted to post an update on my new build issue.
    Here are my specs:
    I bought a MSI Z77A-GD65 motherboard with BIOS v10.8
    - Intel Core i7-2600 CPU 3.4 Ghz
    - BIOS Version E4451IMS V10.8 (i had a issue with the newest BIOS flash v10.11 it wouldn't detect the harddrive, could figure that one out so i went back to v10.8)
    - Balistix Sport 8GB sticks (Total of 32 GB memory installed) I first had 3 sticks so i got another 8GB stick to fill all 4 banks for total of 32 GB
    - Corsair Professional Series 860 Watt Digital ATX/EPS Modular 80 PLUS Platinum Power Supply AX860i (Bought this PS to replace the Kentek PS)
    - N780 TF 3GD5/OC (GeForce GTX 780 GAMING) (traded Geforce GTX 780 card for the MSI version of the GTX 780 card)
    OK... I got the new Corsair 860w power supply installed and i installed the new MSI GTX 780 video card with the specs above everything installed fine no problems and my son was playing the Bio Shock Infinite game on Steam and about 1 hour into the game he got a blue screen of death, says something like "to prevent damage windows is now resetting" and it turns off so fast can't read the rest of the message.
    I'm going to here in a little bit and update all device drivers with MSI Live update utility and also update the motherboard BIOS again to v10.11.
    I'm really confused here, I'm also going to take out some memory and try to run it with sticks only in slot 2 & 4 to see if it runs more stable like that, also should i update the video card to the latest driver, i know the latest is not always the greatest driver.
    I want to think you guys again for your help & time with this issue. I really dont know what else to do here, everything is new in this PC.
    Thanks

  • Problem with i915 Intel driver panic..

    Hello,
    I just recently reinstalled Arch on my laptop.  I have a problem with my laptop. When I went to install the Nvidia Optimus stuff and configure my Xorg.conf I was met with problems with the Intel Driver timing out.  When I boot up I get the normal post screen, then grub, I then go to see the GDM login and instead of getting it I just get a black screen.  When I remove the /etc/X11/xorg.conf.d/10-monitor.conf I can boot into Gnome Shell, else I have to switch run levels and login that way.  I have every package up-to-date.  And I haven't seen an /var/log/Xorg.0.log either else I would have posted it.  One other thing is I have added my user account to the Bumblebee account.  One other thing is when I move my web browser around my video flickers..  Any help I can receive with this would be greatly appreciated.
    uname -a
    Linux tux 3.17.1-1-ARCH #1 SMP PREEMPT Wed Oct 15 15:04:35 CEST 2014 x86_64 GNU/Linux
    pacman -q xf86-video-intel:
    xf86-video-intel 2.99.916-3
    pacman -Q xorg-server
    xorg-server 1.16.1-1
    pacman -Q primus
    primus 20131226-1
    pacman -Q mesa
    mesa 10.3.1-1
    pacman -Q lib32-primus
    lib32-primus 20131226-1
    pacman -Q bbswitch
    bbswitch 0.8-18
    pacman -Q gdm
    gdm 3.14.1-1
    pacman -q systemd
    systemd 216-3
    dmesg | grep i915
    [ 1.982842] i915 0000:00:02.0: irq 36 for MSI/MSI-X
    [ 2.099424] [drm] GMBUS [i915 gmbus vga] timed out, falling back to bit banging on pin 2
    [ 2.127859] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
    [ 2.127862] i915 0000:00:02.0: registered panic notifier
    [ 2.147795] [drm] Initialized i915 1.6.0 20140725 for 0000:00:02.0 on minor 0
    /etc/X11/xorg.conf.d/20-intel.conf
    Section "Device"
    Identifier "Intel"
    Driver "intel"
    Option "AccelMethod" "sna"
    Option "TearFree" "true"
    Option "monitor-LVDS" "Monitor0"
    BusID "PCI:0:2:0"
    EndSection
    /etc/X11/xorg.conf.d/10-keyboard.conf
    Section "InputClass"
    Identifier "Keyboard0"
    MatchIsKeyboard "on"
    Option "XkbLayout" "us"
    Option "XkbModel" "pc104"
    Option "XkbVariant" ",qwerty"
    EndSection
    /etc/X11/xorg.conf.d/50-synaptic.conf
    Section "InputDevice"
    Identifier "Mouse0"
    Driver "mouse"
    Option "Protocol" "auto"
    Option "Device" "/dev/psaux"
    Option "Emulate3Buttons" "no"
    Option "ZAxisMapping" "4 5"
    EndSection
    /etc/X11/xorg.conf.d/10-monitor.conf
    Section "ServerLayout"
    Identifier "Layout0"
    Screen 0 "Screen0"
    InputDevice "Keyboard0" "CoreKeyboard"
    InputDevice "Mouse0" "CorePointer"
    EndSection
    Section "Monitor"
    Identifier "Monitor0"
    HorizSync 28.0 - 33.0
    VertRefresh 43.0 - 72.0
    Option "DPMS"
    EndSection
    Section "Screen"
    Identifier "Screen0"
    Device "Intel"
    Monitor "Monitor0"
    DefaultDepth 24
    SubSection "Display"
    Depth 24
    EndSubSection
    EndSection
    sudo lspci -v
    00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) (prog-if 00 [VGA controller])
    Subsystem: Dell Device 04c8
    Flags: bus master, fast devsel, latency 0, IRQ 36
    Memory at d1400000 (64-bit, non-prefetchable) [size=4M]
    Memory at c0000000 (64-bit, prefetchable) [size=256M]
    I/O ports at 7000 [size=64]
    Expansion ROM at <unassigned> [disabled]
    Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
    Capabilities: [d0] Power Management version 2
    Capabilities: [a4] PCI Advanced Features
    Kernel driver in use: i915
    Kernel modules: i915
    01:00.0 VGA compatible controller: NVIDIA Corporation GF108M [GeForce GT 540M] (rev a1) (prog-if 00 [VGA controller])
    Subsystem: Dell Device 04c8
    Flags: bus master, fast devsel, latency 0, IRQ 7
    Memory at d0000000 (32-bit, non-prefetchable) [size=16M]
    Memory at a0000000 (64-bit, prefetchable) [size=256M]
    Memory at b0000000 (64-bit, prefetchable) [size=32M]
    I/O ports at 6000 [disabled] [size=128]
    Expansion ROM at d1000000 [disabled] [size=512K]
    Capabilities: [60] Power Management version 3
    Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
    Capabilities: [78] Express Endpoint, MSI 00
    Capabilities: [b4] Vendor Specific Information: Len=14 <?>
    Capabilities: [100] Virtual Channel
    Capabilities: [128] Power Budgeting <?>
    Capabilities: [600] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
    Kernel modules: nouveau, nvidia
    xrandr -q
    [adramalech@tux log]$ xrandr
    Screen 0: minimum 8 x 8, current 1366 x 768, maximum 32767 x 32767
    LVDS1 connected primary 1366x768+0+0 (normal left inverted right x axis y axis) 256mm x 144mm
    1366x768 60.05*+
    1024x768 60.00
    800x600 60.32 56.25
    640x480 59.94
    VGA1 disconnected (normal left inverted right x axis y axis)
    VIRTUAL1 disconnected (normal left inverted right x axis y axis)
    cat /proc/bus/input/devices
    I: Bus=0011 Vendor=0001 Product=0001 Version=ab41
    N: Name="AT Translated Set 2 keyboard"
    P: Phys=isa0060/serio0/input0
    S: Sysfs=/devices/platform/i8042/serio0/input/input0
    U: Uniq=
    H: Handlers=sysrq kbd event0
    B: PROP=0
    B: EV=120013
    B: KEY=402000000 380307af800d001 feffffdfffefffff fffffffffffffffe
    B: MSC=10
    B: LED=7
    I: Bus=0019 Vendor=0000 Product=0005 Version=0000
    N: Name="Lid Switch"
    P: Phys=PNP0C0D/button/input0
    S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2
    U: Uniq=
    H: Handlers=event1
    B: PROP=0
    B: EV=21
    B: SW=1
    I: Bus=0019 Vendor=0000 Product=0001 Version=0000
    N: Name="Power Button"
    P: Phys=LNXPWRBN/button/input0
    S: Sysfs=/devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
    U: Uniq=
    H: Handlers=kbd event2
    B: PROP=0
    B: EV=3
    B: KEY=10000000000000 0
    I: Bus=0010 Vendor=001f Product=0001 Version=0100
    N: Name="PC Speaker"
    P: Phys=isa0061/input0
    S: Sysfs=/devices/platform/pcspkr/input/input4
    U: Uniq=
    H: Handlers=kbd event3
    B: PROP=0
    B: EV=40001
    B: SND=6
    I: Bus=0001 Vendor=10ec Product=0665 Version=0001
    N: Name="HDA Digital PCBeep"
    P: Phys=card0/codec#0/beep0
    S: Sysfs=/devices/pci0000:00/0000:00:1b.0/sound/card0/hdaudioC0D0/input6
    U: Uniq=
    H: Handlers=kbd event4
    B: PROP=0
    B: EV=40001
    B: SND=6
    I: Bus=0000 Vendor=0000 Product=0000 Version=0000
    N: Name="HDA Intel PCH Mic"
    P: Phys=ALSA
    S: Sysfs=/devices/pci0000:00/0000:00:1b.0/sound/card0/input7
    U: Uniq=
    H: Handlers=event5
    B: PROP=0
    B: EV=21
    B: SW=10
    I: Bus=0000 Vendor=0000 Product=0000 Version=0000
    N: Name="HDA Intel PCH Headphone"
    P: Phys=ALSA
    S: Sysfs=/devices/pci0000:00/0000:00:1b.0/sound/card0/input8
    U: Uniq=
    H: Handlers=event6
    B: PROP=0
    B: EV=21
    B: SW=4
    I: Bus=0000 Vendor=0000 Product=0000 Version=0000
    N: Name="HDA Intel PCH Headphone"
    P: Phys=ALSA
    S: Sysfs=/devices/pci0000:00/0000:00:1b.0/sound/card0/input9
    U: Uniq=
    H: Handlers=event7
    B: PROP=0
    B: EV=21
    B: SW=4
    I: Bus=0019 Vendor=0000 Product=0000 Version=0000
    N: Name="Dell WMI hotkeys"
    P: Phys=wmi/input0
    S: Sysfs=/devices/virtual/input/input10
    U: Uniq=
    H: Handlers=kbd rfkill event8
    B: PROP=0
    B: EV=13
    B: KEY=1500b00000000 200300000 0 0
    B: MSC=10
    I: Bus=0019 Vendor=0000 Product=0006 Version=0000
    N: Name="Video Bus"
    P: Phys=LNXVIDEO/video/input0
    S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:2f/LNXVIDEO:00/input/input11
    U: Uniq=
    H: Handlers=kbd event9
    B: PROP=0
    B: EV=3
    B: KEY=3e000b00000000 0 0 0
    I: Bus=0019 Vendor=0000 Product=0006 Version=0000
    N: Name="Video Bus"
    P: Phys=LNXVIDEO/video/input0
    S: Sysfs=/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:01/input/input12
    U: Uniq=
    H: Handlers=kbd event10
    B: PROP=0
    B: EV=3
    B: KEY=3e000b00000000 0 0 0
    I: Bus=0003 Vendor=0c45 Product=6430 Version=1208
    N: Name="Laptop_Integrated_Webcam_2M"
    P: Phys=usb-0000:00:1d.0-1.4/button
    S: Sysfs=/devices/pci0000:00/0000:00:1d.0/usb1/1-1/1-1.4/1-1.4:1.0/input/input13
    U: Uniq=
    H: Handlers=kbd event11
    B: PROP=0
    B: EV=3
    B: KEY=100000 0 0 0
    I: Bus=0011 Vendor=0002 Product=0007 Version=01b1
    N: Name="SynPS/2 Synaptics TouchPad"
    P: Phys=isa0060/serio1/input0
    S: Sysfs=/devices/platform/i8042/serio1/input/input5
    U: Uniq=
    H: Handlers=event12 mouse0
    B: PROP=9
    B: EV=b
    B: KEY=6420 30000 0 0 0 0
    B: ABS=260800011000003
    glxinfo | grep OpenGL
    OpenGL vendor string: Intel Open Source Technology Center
    OpenGL renderer string: Mesa DRI Intel(R) Sandybridge Mobile
    OpenGL core profile version string: 3.1 (Core Profile) Mesa 10.3.1
    OpenGL core profile shading language version string: 1.40
    OpenGL core profile context flags: (none)
    OpenGL core profile extensions:
    OpenGL version string: 3.0 Mesa 10.3.1
    OpenGL shading language version string: 1.30
    OpenGL context flags: (none)
    OpenGL extensions:
    OpenGL ES profile version string: OpenGL ES 3.0 Mesa 10.3.1
    OpenGL ES profile shading language version string: OpenGL ES GLSL ES 3.0
    OpenGL ES profile extensions:
    sudo glxgears -info
    Running synchronized to the vertical refresh. The framerate should be
    approximately the same as the monitor refresh rate.
    GL_RENDERER = Mesa DRI Intel(R) Sandybridge Mobile
    GL_VERSION = 3.0 Mesa 10.3.1
    GL_VENDOR = Intel Open Source Technology Center
    GL_EXTENSIONS = GL_ARB_multisample GL_EXT_abgr GL_EXT_bgra GL_EXT_blend_color GL_EXT_blend_minmax GL_EXT_blend_subtract GL_EXT_copy_texture GL_EXT_polygon_offset GL_EXT_subtexture GL_EXT_texture_object GL_EXT_vertex_array GL_EXT_compiled_vertex_array GL_EXT_texture GL_EXT_texture3D GL_IBM_rasterpos_clip GL_ARB_point_parameters GL_EXT_draw_range_elements GL_EXT_packed_pixels GL_EXT_point_parameters GL_EXT_rescale_normal GL_EXT_separate_specular_color GL_EXT_texture_edge_clamp GL_SGIS_generate_mipmap GL_SGIS_texture_border_clamp GL_SGIS_texture_edge_clamp GL_SGIS_texture_lod GL_ARB_framebuffer_sRGB GL_ARB_multitexture GL_EXT_framebuffer_sRGB GL_IBM_multimode_draw_arrays GL_IBM_texture_mirrored_repeat GL_3DFX_texture_compression_FXT1 GL_ARB_texture_cube_map GL_ARB_texture_env_add GL_ARB_transpose_matrix GL_EXT_blend_func_separate GL_EXT_fog_coord GL_EXT_multi_draw_arrays GL_EXT_secondary_color GL_EXT_texture_env_add GL_EXT_texture_filter_anisotropic GL_EXT_texture_lod_bias GL_INGR_blend_func_separate GL_NV_blend_square GL_NV_light_max_exponent GL_NV_texgen_reflection GL_NV_texture_env_combine4 GL_S3_s3tc GL_SUN_multi_draw_arrays GL_ARB_texture_border_clamp GL_ARB_texture_compression GL_EXT_framebuffer_object GL_EXT_texture_compression_s3tc GL_EXT_texture_env_combine GL_EXT_texture_env_dot3 GL_MESA_window_pos GL_NV_packed_depth_stencil GL_NV_texture_rectangle GL_ARB_depth_texture GL_ARB_occlusion_query GL_ARB_shadow GL_ARB_texture_env_combine GL_ARB_texture_env_crossbar GL_ARB_texture_env_dot3 GL_ARB_texture_mirrored_repeat GL_ARB_window_pos GL_EXT_stencil_two_side GL_EXT_texture_cube_map GL_NV_depth_clamp GL_APPLE_packed_pixels GL_APPLE_vertex_array_object GL_ARB_draw_buffers GL_ARB_fragment_program GL_ARB_fragment_shader GL_ARB_shader_objects GL_ARB_vertex_program GL_ARB_vertex_shader GL_ATI_draw_buffers GL_ATI_texture_env_combine3 GL_ATI_texture_float GL_EXT_shadow_funcs GL_EXT_stencil_wrap GL_MESA_pack_invert GL_NV_primitive_restart GL_ARB_depth_clamp GL_ARB_fragment_program_shadow GL_ARB_half_float_pixel GL_ARB_occlusion_query2 GL_ARB_point_sprite GL_ARB_shading_language_100 GL_ARB_sync GL_ARB_texture_non_power_of_two GL_ARB_vertex_buffer_object GL_ATI_blend_equation_separate GL_EXT_blend_equation_separate GL_OES_read_format GL_ARB_color_buffer_float GL_ARB_pixel_buffer_object GL_ARB_texture_compression_rgtc GL_ARB_texture_float GL_ARB_texture_rectangle GL_EXT_packed_float GL_EXT_pixel_buffer_object GL_EXT_texture_compression_dxt1 GL_EXT_texture_compression_rgtc GL_EXT_texture_rectangle GL_EXT_texture_sRGB GL_EXT_texture_shared_exponent GL_ARB_framebuffer_object GL_EXT_framebuffer_blit GL_EXT_framebuffer_multisample GL_EXT_packed_depth_stencil GL_APPLE_object_purgeable GL_ARB_vertex_array_object GL_ATI_separate_stencil GL_EXT_draw_buffers2 GL_EXT_draw_instanced GL_EXT_gpu_program_parameters GL_EXT_texture_array GL_EXT_texture_integer GL_EXT_texture_sRGB_decode GL_EXT_timer_query GL_OES_EGL_image GL_AMD_performance_monitor GL_ARB_copy_buffer GL_ARB_depth_buffer_float GL_ARB_draw_instanced GL_ARB_half_float_vertex GL_ARB_instanced_arrays GL_ARB_map_buffer_range GL_ARB_texture_rg GL_ARB_texture_swizzle GL_ARB_vertex_array_bgra GL_EXT_texture_swizzle GL_EXT_vertex_array_bgra GL_NV_conditional_render GL_AMD_draw_buffers_blend GL_AMD_seamless_cubemap_per_texture GL_ARB_ES2_compatibility GL_ARB_blend_func_extended GL_ARB_debug_output GL_ARB_draw_buffers_blend GL_ARB_draw_elements_base_vertex GL_ARB_explicit_attrib_location GL_ARB_fragment_coord_conventions GL_ARB_provoking_vertex GL_ARB_sample_shading GL_ARB_sampler_objects GL_ARB_seamless_cube_map GL_ARB_shader_texture_lod GL_ARB_texture_cube_map_array GL_ARB_texture_gather GL_ARB_texture_multisample GL_ARB_texture_query_lod GL_ARB_texture_rgb10_a2ui GL_ARB_uniform_buffer_object GL_ARB_vertex_type_2_10_10_10_rev GL_EXT_provoking_vertex GL_EXT_texture_snorm GL_MESA_texture_signed_rgba GL_ARB_get_program_binary GL_ARB_robustness GL_ARB_separate_shader_objects GL_ARB_shader_bit_encoding GL_ARB_timer_query GL_ANGLE_texture_compression_dxt3 GL_ANGLE_texture_compression_dxt5 GL_ARB_compressed_texture_pixel_storage GL_ARB_internalformat_query GL_ARB_map_buffer_alignment GL_ARB_shading_language_420pack GL_ARB_shading_language_packing GL_ARB_texture_storage GL_EXT_framebuffer_multisample_blit_scaled GL_EXT_transform_feedback GL_AMD_shader_trinary_minmax GL_ARB_ES3_compatibility GL_ARB_clear_buffer_object GL_ARB_copy_image GL_ARB_explicit_uniform_location GL_ARB_invalidate_subdata GL_ARB_texture_query_levels GL_ARB_texture_storage_multisample GL_ARB_vertex_attrib_binding GL_KHR_debug GL_ARB_buffer_storage GL_ARB_clear_texture GL_ARB_multi_bind GL_ARB_seamless_cubemap_per_texture GL_ARB_texture_mirror_clamp_to_edge GL_ARB_vertex_type_10f_11f_11f_rev GL_EXT_shader_integer_mix GL_INTEL_performance_query GL_ARB_conditional_render_inverted
    VisualID 32, 0x20

    Hi
    I assume you have installed the graphic card driver from the Intel website and you use NOT a Toshiba graphic driver which was designed especially for the notebook usage.
    Well, Toshiba recommend using the Toshiba drivers. In this case you should try to use the recommended graphic driver which you can download from the Toshiba driver page.

  • Right, MacBook Pro 17" early 2011(Built March) and my new OCZ sata III 6G not working, when is Apple going to admit there is a problem with the Intel's 6 Series Chipset. In System Information it says "Link Speed: 6 Gigabit" which is sata III.

    My MacBook Pro 17" early 2011(built March) and my new OCZ sata III 6G are not working together, when is Apple going to admit there is a problem with the Intel's 6 Series Chipset. In System Information it says "Link Speed: 6 Gigabit" which is sata III and in my MacBook Pro it does not work. 
    Now MacBook Pro 17" early 2011 built May onward do not have this problem it was fixed in the Intel's 6 Series Chipset. (So there is a problem). Cam I have my MacBook Pro fixed please.

    After biting the bullet and ordering more RAM, my computer now is working a ton better. So that must have been the main issue. With 8 GB RAM, I can now even run Parallels fluidly (better than my work PC!) where before simple things like logging in to my MBP after reboot could take forever.
    The place I went to had several other people getting RAM upgrades at the same time as me, so between this and other comments I've seen in discussions here and elsewhere on the Internets, I take it to mean that either Apple should bump up the base RAM on its new machines, and/or stop charging so much for additional RAM.
    I refused to believe a Pro machine bought with Lion installed would come with too little RAM for light to medium usage, but it was apparently the case. I'll mark this as a correct answer and hope some other poor soul will come across this thread and be helped by it.

  • I have Power Mac G5 1.8 single. I have a problem with ethernet port, before it was working with the internet, but now i shows it is connected even the cable is disconnected. I'm running Leopard 10.5. any help

    I have Power Mac G5 1.8 single. I have a problem with ethernet port, before it was working with the internet, but now i shows it is connected even the cable is disconnected. I'm running Leopard 10.5. any help

    Reset the PRAM.
    http://support.apple.com/kb/HT1379
    If that fails, reset the PMU.
    Scroll down the following page and click the G5 link for instructions:
    http://support.apple.com/kb/ht1939

  • Problem with installing Photoshop elements 9 and adobe support advisor

    Hi, I've received a graphic tablet with 2 programs: the first has been downloaded and works perfectly while the second, PSE9, has been giving me problems for at least a week!
    I downloaded it and now I have a winzip file full of strange things (one of this is set up exe which tells me that I have to install adobe support advisor) and two files which said 3DF.tmp and PSEP9(1).zip.download and if I try to click them they tell me that I have to find on the Net the program to open them because I can't. And I don't know which program is required.
    I tried a lot of times to download the adobe support advisor, I have enough space on my disc and my farewall is deactivated, but when the program begins I saw this annoyant message
    cpsid_82829s5 Missing installation file bootstrapper error occured
    with this code for a support from adobe 00-67325-032018052012
    I unistalled it and retried, but nothing.
    Please, I just want to use my tablet with the programs which are comprised in the package, why it's so difficult to download this damn photoshop elements 9????????????
    Thank you

    In the error message it doesn't tell me
    "Installer has detected that a machine restart is pending. It is recommended that you quit the installer, restart try again,"
    neither "Installer failed to initialize. File not found. Please download Adobe Support Advisor to detect the problem."
    and I have enough space and I have Windows xp then I should be able to install it. I tried to unistall and install again the support advisor but nothing. I'm desperate.
    Messaggio originale----
    Da: [email protected]
    Data: 18/05/2012 22.20
    A: "Questionlady"<[email protected]>
    Ogg: Problem with installing Photoshop elements 9 and adobe support advisor
    Re: Problem with installing Photoshop elements 9 and adobe support advisor created by Jeff A Wright in Trial Download &amp; Install FAQ - View the full discussion
    Did you try the steps listed in http://helpx.adobe.com/creative-suite/kb/troubleshoot-error-messages-b ootstrapper-cs5.html which was identified by the Adobe Support Advisor?  If so can you please list each step and the result of those steps.  This will allow us to best advise you on your next steps.
    Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/4420419#4420419
    To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/4420419#4420419. In the Actions box on the right, click the Stop Email Notifications link.
    Start a new discussion in Trial Download &amp; Install FAQ by email or at Adobe Forums
    For more information about maintaining your forum email notifications please go to http://forums.adobe.com/message/2936746#2936746.

  • Problem with QT 7.1.5 and Sorensen codec?

    Has anyone noticed a compatibility problem with Sorensen video 3 codec and Quicktime 7.1.5? This problem did not seem to exist in prior versions (hence have been asking how to reinstall previous version but seems impossible). Some of the earlier postings discuss software that may be designed with Sorensen codec... these may be the ones not functioning properly now (video no longer works). Does this sounds plausible?
    Mac Mac OS X (10.4.8)
    Mac Mac OS X (10.4.8)
    Mac   Mac OS X (10.4.8)  

    That may be true, Jack, but Edmund said that the movie played in QuickTime Player. So his problem is most likely not a bug in QuickTime, though I can't say for certain.
    And as I said above, I have no problem playing Sorenson-encoded content on my Intel-based Mac with QuickTime 7.1.5, so more details about your content and setup (including any third-party codecs you may have installed) so that people can determine what the difference might be between the content that plays and the content that does not, or what's different in the systems, would be helpful, I'm sure.

  • I'm using mac with the newest operating system (snow leopard 10.6.7). since I've updated to Firefox 4 It doesn't display Hebrew fonts- I didn't have any problems with it before the upgrade and in safari I don't have this problem.

    Hello, I'm using Mac with the newest operating system (snow leopard 10.6.7). since I've updated to Firefox 4 It doesn't display Hebrew fonts… I didn't have any problems with it before the upgrade and in safari I have no problem with it. please help me- I don't like to use safari a my browser...

    elly903 wrote:
    Before commenting - I CANNOT install Mavericks because it'll mess up the versions of Filemaker Pro and Quicken that I use regularly...
    Quicken 2007 for Intel (Snow Leopard, Lion, Mt. Lion and Mavericks) for $15:
    http://quicken.intuit.com/personal-finance-software/quicken-2007-osx-lion.jsp
    It will input your Quicken PPC data file directly if it was Quicken 2005 through 2007.  If older you need Quicken 2006 or 2007 PPC first to convert your data file; and this update must be done BEFORE you upgrade to Mavericks:
    http://quicken.intuit.com/support/help/patching/quicken-2006-manual-updates--mac -/GEN82200.html
    Filemaker Pro PPC (in this case 7) running in Snow Leopard Server installed into Parallels for use in Lion, Mt. Lion and Mavericks:
                                  [click on image to enlarge]
    Snow Leopard Server: 1.800.MYAPPLE (1.800.692.7753) - Apple Part Number: MC588Z/A (telephone orders only)
    This solution allows you to run your Photoshop Elements in Mavericks concurrently with Filemaker Pro PPC.  Mavericks is a free download.

  • My host name changes every few days, since Xmas adding a macbook its changed 6 times. Do I need to stop this? Does it cause problems with sharing between the iMac and macbook?

    my host name changes every few days, since Xmas adding a macbook its changed 6 times. Do I need to stop this? Does it cause problems with sharing between the iMac and macbook?

    There are several possible causes for this problem.
    1. Two (or more) computers on the local network have the same Bonjour name, such as "X's-MacBook-Pro.local".
    2. You have two simultaneous connections to the same local network: probably Ethernet and Wi-Fi. If applicable, disconnect the Ethernet cable or turn off Wi-Fi.
    3. A Mac wakes from sleep due to network traffic. This is due to a bug in OS X that may only affect some models.
    4. A device that gets its network address from the router wakes from sleep, and the address it was using before has been assigned to another device.
    5. A third-party wireless router has incompatible settings or firmware. In that case, refer to the manufacturer or ISP for support. Restarting the router may help, temporarily.
    6. See also this support article.
    Rename the computer in the Sharing preference pane.

  • Problem with Xsan 2.1.1 and Mac Os server 10.5.6

    Hi,
    We have a big problem with xsan 2.1.1 and Mac Os server 10.5.6.
    - We have one server, is a Open Directory Master, and also is a metadata controller of xsan2. The Volumes of xsan2 are shares via afp, and the clients (moreless 50) connect with server via afp.
    - We have some problems, one of them is:
    odm fsm [341]: XSAN FSS 'VolDocs [0] ' : Invalid inode lookup: 0x7f80000000007e0 markers 0x0/0x0 nextiel 0x0
    This message is always in the log. We stop the volume, and start cvfsck -wv, but dont have anything, how fix it??
    - Another problem is with AFP service, suddenly the service stop, and the error is :
    mds [58] (error) Server: Mach error queueing checkin to peer manager: (ipc /send) invalid port right.
    -What of the meaning of (ipc/send) invalid port right??.
    And the last error is:
    -com.appelAppleFileServer [347] MDSChannelPeerRequest: (ipc/rcv) timed out.
    Need Help please!.

    My configuration:
    - Master Directory:
    Hardware Configuration:
    Model: Xserve
    Processor: 2x2,8 Ghz Quad-Core Intel Xeon
    Memory 8 Gb
    Disk: 70,04 Tb
    Software:
    Kernel Version: 9.6.0
    System Version: Mac OS X Server 10.5.6
    Xsan 2.1.1
    Services: AFP, DNS, Open Directory RADIUS
    Status: connected Users: 37
    This server is the open directory Master and metadata controller of xsan2, but we have another server that is open directory replica and metadata controller of xsan2. The fisrt server have too many errors with afp, the service stop and the server is dead, and you must restart via terminal with the command sudo reboot. I dont know what happen, do you help me please?

Maybe you are looking for