Z77A-GD65 / Video issues

Hey All
Got a real weird issue going on
Randomly when playing games my computer will shutdown and reboot. When it boots up the video card is blurry during Post and bios splash screen. Once windows attempts to load the computer reboots again.
Changing to the onboard video card works fine
If I swap the PCI-E to another slot it will work again but the issue will reoccur in a matter of time - can be days or minutes
Video Card runs in high load environments such as ARMA3 and Starcraft with issues. Previously had not experienced an issue.
It's just really weird
System
MB: MSI Z77A-GD65
Video: GTX 580
Memory: 16GB Gskill 2400
Any help or ideas would be awesome
Regards,
Mag

could be overheating for sure so like dude said check the temps under load and see if its temp is very high?
also it could be RAM errors so try >>Memtest86<< and see if it throws errors or if the computer restarts while its active?
could also be PSU related as you have not listed what power supply you have as it may be having a power shutdown issue as the PSU is not capable of sustaining a stable power delivery?

Similar Messages

Z77A-GD65 power issue/bad system board?

Looking for advice. I am afraid its a bad board, but some symptoms point at power which also makes no sense.
This is what the WHOLE system should look like.
MSI Z77A-GD65 system board
Intel 3770K 3.5Ghz
Anted Kuhler H20 620
G.Skills RipJaws 16GB 1600Mhz DDR3 F3-14900CL9Q-16GBXL (on the test list)
Asus nVidia GTX 680 video card
OCX Vertex 3 256MB SSD
Seagate 500GB data drive
Razer Lycosa Keyboard
Razer DeathAdder Mouse
Antec Sonata IV case with Neo ECO 620W power supply
It seems to me that 620W should be more than enough. According to my calculations thats roughly 330W of power draw against a 620W powersupply.
I am not currently over clocking.
So what the system does look like is:
If I connect the 500GB drive then windows starts rebooting as soon as the Windows logo comes up.
If I place all four sticks of RAM in the system windows starts rebooting as soon as the Windows logo comes up.
If I leave the 500GB standard sata drive off and only use 3 sticks of RAM... well we get a solid system and I am writing this message on it.
3 sticks of ram appear to work in any 3 slots and allow the system to boot, except 1,3,4. That combo also resulted in the reboots at the windows logo.
I first thought it was RAM, originally I was using Corsair Vengeance. I saw some posts here about people having the same problem, and noted that the Corsiar RAM was not tested and switch to a the tested G.Skill instead.
Any ideas? It does not completely seem like a System board issue, but it certainly should not be power. All heat levels are well within normal and as I said the system works great if I leave off the drive and one stick of RAM.
Thanks guys....

System torn down, and put back together. (Found out I was out of Thrermal Compound, so I had to run to the store to get some.)
No long leads, only 9 stand offs matching each mount point on the systemboard.
Back together... problem is the exact same.
However, back to the hard drive issue. I decided to play with that since I was getting no where with 4 sticks of RAM.
What I have discovered is that with NO sata cable connecting the drive to the system board, if I try to power the two 250GB standard sata drives the system reboots just as the Windows logo should come up.
The fact that this behavior is so close to the RAM behavior... I am back to thinking its a power issue, though system board is still a chance... its just easier to buy a new better power supply than the Antec Neo Power 620 that came with the case. (I have not ever had a problem with Antec before, and will likely just buy one of their higher end power supplies to replace it, but I think I will try it next, just in case.)
I am not seeing any strange behavior power wise as far as any monitor shows... but connecting power to a sata drive that is NOT connected with a sata cable and causing a reboot just screams power at me.
Anymore thoughts today. In the mean time off to play Secret World with just the SSD and two sticks of RAM, which still runs rock solid.

Z77A-GD65 boot issue!

Hey.
I have this Z77A-GD65 motherboard which I bought around July 2012, which has been working great until this morning. First of all, I don't do any overclocking, It has no meaning to me and I didn't change anything on the BIOS, not even used it prior to this problem.
Problem is, PC won't post, It will turn on for 3-4 secs until reaching debug code 55 then it will simply shutdown and restart by itself, going into a cycle, just let me repeat, there is no BIOS, no post only black screen.
I tried switching Bios A and B, clearing data on both Bios A and B, replacing the Bios battery. I replaced the Core i5 3750K with a Core i7, I changed memory sticks, even replaced the 670 GTX card with a 660Ti card. Replaced my CoolerMaster PSU with a Corsair one and none of these changes helped.
I did this both inside the case and outside the case and gave the motherboard a good airblow to remove the little dust it had on it.
All the other component worked just fine in another PC.
So basically, I did every troubleshooting I know, It feels like a shortcut but I inspected the motherboard and it seems to be in good physical condition.
I think it needs a RMA, whats the best thing to do now?
Thx for any help!

You are in South America?
You could also just email [email protected] if you wished. Might be recommended if that is the case due to the nearest service center being in the USA. Unless they opened a new one recently.
Yup:
Quote
South American
MSI Computer do Brasil Ltda
Tel: (+5511) 4949-8888
Fax: (+5511) 4949 8808
Website:http://br.msi.com/
Sede Central de América Latina
Dirección: 901 Canada Court, City of Industry, CA 91748 U.S.A.
Tel: + 1-626-913-0828
Horario de Atencion :Lunes-Viernes (9:00AM - 6:00PM PST)
Para enviarnos un e-mail, por favor diríjase a alguna de las siguientes direcciones:
Departamento de Placas Madre, Tarjetas de Video & AIl-in-One PC
Ventas: [email protected]
Marketing: [email protected]
Departamento de Notebook PC y Tablet
Tel: + 1-305-591-2229
E-mail: [email protected]
Centros de Servicio Autorizados para Notebooks en Latinoamérica
Por favor ir a la página de Servicio y Soporte en la Sección de Centros de Servicio.
Departamento de Soporte Técnico RMA(toda linea de productos)
RMA: [email protected] o marcando 1-305-591-2229 (opcion 5)
Soporte técnico: [email protected] o marcando 1-305-591-2229 (opcion 5)
FAX:
Soporte Técnico & RMA : +1-626-581-1551
Ventas & Marketing: +1-626-913-0818
Departamento de RR.HH. : +1-626-913-0819
Departamento Contable: +1-626-913-0897

Z77a-gd65-having issues running 2 gtx 560 sc in sli--any help out there???

I just built this unit last night and I have a issue that is beyond me....Normally I just throw them together and throw to cards in download all the drivers and turn on sli.......
But with this one the driver keeps crashing and I have no idea what it is--everything is brand new....
z77a-gd65-----I7 3770k
16gb g.skill ripjaws-----------4x4 sticks running in 1333 not 1600
samsung ssd.....
water loop....plenty of cooling....
2 gtx 560 sc 2gb version in sli
BCCode:   117
BCP1:   FFFFFA800D7DC010
BCP2:   FFFFF880049C0198
BCP3:   0000000000000000
BCP4:   0000000000000000
OS Version:   6_1_7601
Service Pack:   1_0
Product:   256_1
It only does this in sli......Right now I have only one card in and i took the other card out...so far no issues......I just can not figure it out..
I tried a new sli brindge and that did not work....Than I switched power supply to 850 from a 750 and that did not work....each 6 pin has it own power rail..nothing brindged on the cable.....Is there a setting In bios I am missing............
Help me out guys....I am at a loss..I really want to run 2 cards.....will be testing the single card for a few more hours and that I will swap it out with the other.....But am I missing something.....Voltage on each card is kind of weird I guess..1.00 volts to .850........

Quote
I know this is besides the point...But you learn something new everyday.....so far no crash....Only difference---I have 2 sticks of ram and not 4....I really would like to know more about this. as of right now. I want to just leave the 2 sticks and make 100% sure the cards are not the issue. You would figure with this set up...I should not have any issues like that what so ever......so why would the i7 3770k have issue like this? Is it know to have problems like that? I even spent the extra cash on this build....now I am second guessing my choice. should have stuck with the z77a-gd55 or lower. So you think the cpu was having issue with the IMC and bandwidth...Talk about weird....I will keep testing like it is right now and than tmr-try uping the voltage & I/O.....I need to make 100% sure its not my cards...
I think you mis-understood (as i wasn't clear)
Set the voltage to 1.65 & 1.1 and install all 4 sticks and re-test.
I wasn't saying the cpu was broken or anything like that. What I was getting at was that the Integrated Memory Controller on dual channel machines sometime have a bit of trouble with all of the band width when hooked up to quad channel. Can also be cause by the memory itself as Froggy was saying:
Quote
Test the other two sticks individually in the primary DIMM slot to see if one or both are faulty.
Virtu-MVP was an exciting idea that hasn't really worked as well as it should due to a lack of support from LUCID. I disabled mine long ago due to nusiance issues.
Quote
Right now---since I have taken out the 2 extra sticks of Ram.....I have not had a single crash..."2 hours".I even turn up the stick to the suggested 1600...Running great...I am a firm believer if it an't broke.....Leave it alone>>>>>>>>>>LOL!!!!!I like the way it is running....
If this is the case, you can reset the dramv and I/o voltage to "Auto".
Perhaps even enable the XMP profile of the ram.

Z77A GD65 Network Issue

Not sure what would be the cause hopefully someone here in the forums can shine some light on this problem.
When I turn the computer off and let it sit for a very long time and I turn the PC on the internet will not work windows rejects to pick it up. Only way to get internet on the system is to restart again and then you have internet.
If I reboot anymore with the system internet works just fine. It seems to do it when you let it stay off for a long time from what am looking at. So when I wake up I have to turn the system on let windows boot to desktop then restart again and I have internet.

I've got the same network problem at cold startup with Z77A GD65. So I used the recomanded driver for Windows 8 64bit.
After just update It seems to work fine, but is see that instead of the 82579LM now its says 82579V. Is that OK?
I still got a unknown device in my devicemanager saying:
De installatie van stuurprogramma NULL Driver voor apparaat-id ACPI\INT33A0\0 is voltooid door Stuurprogrammabeheer met de volgende status: 0x0.
Translation:
The installation of driver NULL Driver for device-id ACPI\INT33A0\0 is done bij driver program manager with the folowing status: 0x0
Just read at intel website that the LM is not the same as V. (82579-gbe-phy-datasheet-vol-2-1.pdf)
It has less capabillities. Is there another driver avalable for Windows 8 64bit for the LM version that solves the cold startup problem?
Sorry, I am confused. I'm sure my device manager said LM before i updated, but in the documentation by the MS-7751 (v2.x) and on the MSi website is says V.
Dues this mean that MSi Live Update 5 did download the wrong driver before?

Z77A-GD65 issues with Geforce GTX 780 Video Card

Hey Guys,
I have a issue with a new PC build.
I think it may be a driver or BIOS setting issue, I hope
I bought a MSI Z77A-GD65 motherboard and below are the specs:
- Intel Core i7-2600 CPU 3.4 Ghz
- BIOS Version E4451IMS V10.8
- Balistix Sport 8GB sticks (Total of 24 GB memory installed)
- Kentek 875w power supply
- Geforce GTX 780 Graphics Card
My problem is with the Geforce GTX 780 video card, I installed a fresh install of Windows 7 64 bit and
everything runs and works fine,but when i install the Geforce GTX 780 video card and install the
drivers its all good up to this point but when i restart the computer i get this message in the device
manager ""Windows has stopped this device because it has reported problems (code 43)"
I have installed different versions of the driver, a few older and few newer versions with the same
outcome.
I tried to flash the BIOS to the latest version 10.11 but had problems with it picking up my harddrive
after it flashed successfully. I even checked the boot up setting and it all looked good just would not
boot up, so i had to revert back to the v10.8 BIOS version for it to work.
I'm not sure if there is a setting in the BIOS that i need to turn on or off. I'm not familar with this BIOS,
is there a place in it so i can see if the BIOS is picking up the video card, it has to or Windows would
not see it right?
I'm stumped here, do you guys know of a Geforce driver version that works well with this video card?
I truely think the card is fine because when i install the card to the motherboard i dont get any weird
issues until the driver is installed and Windows is restarted.
I would greatly appreciate any help and advise that you guys can give me.
Thanks alot

UPDATE
Well i wanted to post an update on my new build issue.
Here are my specs:
I bought a MSI Z77A-GD65 motherboard with BIOS v10.8
- Intel Core i7-2600 CPU 3.4 Ghz
- BIOS Version E4451IMS V10.8 (i had a issue with the newest BIOS flash v10.11 it wouldn't detect the harddrive, could figure that one out so i went back to v10.8)
- Balistix Sport 8GB sticks (Total of 32 GB memory installed) I first had 3 sticks so i got another 8GB stick to fill all 4 banks for total of 32 GB
- Corsair Professional Series 860 Watt Digital ATX/EPS Modular 80 PLUS Platinum Power Supply AX860i (Bought this PS to replace the Kentek PS)
- N780 TF 3GD5/OC (GeForce GTX 780 GAMING) (traded Geforce GTX 780 card for the MSI version of the GTX 780 card)
OK... I got the new Corsair 860w power supply installed and i installed the new MSI GTX 780 video card with the specs above everything installed fine no problems and my son was playing the Bio Shock Infinite game on Steam and about 1 hour into the game he got a blue screen of death, says something like "to prevent damage windows is now resetting" and it turns off so fast can't read the rest of the message.
I'm going to here in a little bit and update all device drivers with MSI Live update utility and also update the motherboard BIOS again to v10.11.
I'm really confused here, I'm also going to take out some memory and try to run it with sticks only in slot 2 & 4 to see if it runs more stable like that, also should i update the video card to the latest driver, i know the latest is not always the greatest driver.
I want to think you guys again for your help & time with this issue. I really dont know what else to do here, everything is new in this PC.
Thanks

MOVED: Z77A-GD65 issues with Geforce GTX 780 Video Card

This topic has been moved to Intel Core-iX boards.
https://forum-en.msi.com/index.php?topic=177652.0

UPDATE
Well i wanted to post an update on my new build issue.
Here are my specs:
I bought a MSI Z77A-GD65 motherboard with BIOS v10.8
- Intel Core i7-2600 CPU 3.4 Ghz
- BIOS Version E4451IMS V10.8 (i had a issue with the newest BIOS flash v10.11 it wouldn't detect the harddrive, could figure that one out so i went back to v10.8)
- Balistix Sport 8GB sticks (Total of 32 GB memory installed) I first had 3 sticks so i got another 8GB stick to fill all 4 banks for total of 32 GB
- Corsair Professional Series 860 Watt Digital ATX/EPS Modular 80 PLUS Platinum Power Supply AX860i (Bought this PS to replace the Kentek PS)
- N780 TF 3GD5/OC (GeForce GTX 780 GAMING) (traded Geforce GTX 780 card for the MSI version of the GTX 780 card)
OK... I got the new Corsair 860w power supply installed and i installed the new MSI GTX 780 video card with the specs above everything installed fine no problems and my son was playing the Bio Shock Infinite game on Steam and about 1 hour into the game he got a blue screen of death, says something like "to prevent damage windows is now resetting" and it turns off so fast can't read the rest of the message.
I'm going to here in a little bit and update all device drivers with MSI Live update utility and also update the motherboard BIOS again to v10.11.
I'm really confused here, I'm also going to take out some memory and try to run it with sticks only in slot 2 & 4 to see if it runs more stable like that, also should i update the video card to the latest driver, i know the latest is not always the greatest driver.
I want to think you guys again for your help & time with this issue. I really dont know what else to do here, everything is new in this PC.
Thanks

Z77A-GD65 Quick Sync with Virtu MVP Issue

Hi everyone! My apologies if this has been answered elsewhere but my searching didn't find anything conclusive. I'm a very happy convert from an EVGA P67 SLI board (ugh) to an MSI Z77A-GD65 (YAY!) So far, I absolutely love this board but I'm having an issue I hope someone can answer. I run a YouTube channel and render a lot of video using Sony Movie Studio Platinum. This product is supposed to support Intel's Quick Sync technology to greatly speed up processing times. Normally, you need to have a monitor running off the IGP for this to be available but Virtu MVP is supposed to get around this. I have a GTX770 as my main video card and a Core i7-2600K which is confirmed to support Quick Sync. However, I've had no luck getting Quick Sync to appear as available to Movie Studio Platinum. Here's what I've done:
1. Enabled IGP in the BIOS (also tried making it the primary display adapter, didn't change anything.)
2. Installed latest drivers for both Intel HD 3000 and my GTX770. Both are available to the system.
3. Set Virtu MVP as D-Mode (either mode supposedly enables Quick Sync and D-Mode's obviously better for gaming.)
4. Installed the Virtu MVP software and created a profile for Movie Studio Platinum. Tried it in both D-Mode and I-Mode through the software.
The short of it is that Movie Studio Platinum does not recognise Quick Sync as being available. It's just not selectable which means it can't detect it. I've also tried plugging my secondary monitor directly into the IGP. This isn't supposed to be necessary with Virtu MVP but I don't game on my second monitor so whatever. Still nothing. I'm kind of at a loss for what to do now. I've been told that most mainboards require you to enable Quick Sync specifically in the BIOS but I don't see that option. Is it just always enabled when the IGP is on this board or does it have to be toggled elsewhere?
If anyone has advice on this, I would really appreciate it. My purchase of this board wasn't contingent on Quick Sync but given the amount of video rendering I'm doing right now, having that acceleration would be a massive boon to me. This feels like I'm just missing something simple. Any advice people can offer? Thanks a ton everyone!

I actually did download the latest MVP from their site, is that what you're talking about or something else?
I'm pleased to report that my Quick Sync issue has been resolved and well, it was pretty much my fault. Turns out only certain rendering profiles in Movie Studio Platinum are able to use Quick Sync. Their documentation didn't make this clear but I stumbled over the solution and it's working like a charm. Thanks!

Z77A-GD65 Multiple BIOS Issues - B4 Hang, Splash Screen Blinking

Back in November 2012, I built a home server with a Z77A-GD65. Lately, I've noticed some strange things happening that I've been trying to research but to no avail.
First off, I get the B4 code hang-up whenever I'm booting. This doesn't matter if it's a cold boot or a reboot, it hangs on B4 for about 10-15 seconds, flashes 92 really quick, and then goes to A2 which it stays for another 5 or so seconds. After that I get the MSI splash screen for about 1 second, then it blinks 5 times. After that it goes into Windows just fine.
The blinking is a new issue, the B4 hang is not. I've read from multiple posts that this is a USB issue. When I disable USB legacy support, the issue goes away, but of course then I can't have legacy support. I have yet to figure out what exact device is causing it. In the process of trying to figure this out, I updated BIOS to A.A0. After updating to this version of BIOS the splash screen blinks 5 times before going to the "Starting Windows" splash screen. This is a more difficult issue to figure out why it's doing this because if you search for "BIOS" and "flash" or "flashes" or "flashing", you typically get results for flashing your BIOS. Hence, why I'm using the term "blinking". But even then I can't really find a solution out there.
I also happened to see that the website for the Z77A-GD65 is showing a newer BIOS version, but I'm unable to flash this (at least using M-Flash). I threw it on a USB, re-enabled USB legacy and whenever I click on it to install, the BIOS screen hard locks. The screen just freezes exactly where it's at in the BIOS and the mouse is dead. However, I can CTRL+ALT+DEL on the keyboard and it will reboot the system so I don't need to power cycle the computer. Not sure why this is happening either. Perhaps I need to flash this a different way? Maybe I don't need to flash this at all?
I could really use some input here on why this is happening.
As for the specs on my system, they're as follows:
i7-3770K overclocked to 4.2 Ghz by using the Turbo Mode in BIOS
32GB Komputerbay DDR3 PC3-12800 1600MHz DIMM with Low Profile Blue Heatspreaders Quad Channel RAM | 9-9-9-24 XMP ready
AMD PowerColor 7870 Myst Edition GPU - currently not overclocked although overclocking this doesn't seem to affect any issues
2 - 128 GB Corsair SATA III SSD - one runs the OS, the other I use to load games from
2 - 500 GB Seagate Barracuda 7200 RPM Sata II HDD's mirrored via Windows 7
1 - 750 GB Seagate Barracude 7200 RPM Sata II HDD
1 - 1 TB Western Digital MyBook USB 2.0 external
2 - 3 TB Seagate USB 3.0 external
ASUS DVD Burner - not sure which one, it's a cheapy $20 from Newegg
1 - PCI USB 3.0 expansion card
Antec TruePower New TP-550 Modular 550W Continuous Power ATX12V V2.3 / EPS12V V2.91 SLI Certified CrossFire Ready 80 PLUS BRONZE Certified Active PFC "compatible with Core i7/Core i5" Power Supply
NZXT Switch 810 gunmetal - currently have 4 fans running but plan on more, also the Switch 810 has the multi-card reader in the front with 1x SD Card, 2x USB 2.0, 2x USB 3.0
for peripherals
1 - Microsoft 360 Wireless controller adapter (legit one, not the knockoff although I had a knockoff prior to getting the real deal)
1 - Logitech Wireless USB Keyboard with Touchpad
I tried to be thorough. Thanks in advance for any help!

Quote from: PirateDog on 26-August-13, 12:45:18
Probably a USB device problem.
This is a candidate, as well as mouse and keyboard. Disconnect USB devices one at a time to find the culprit.
A lot of devices running. PSU a +12V single rail or is it multi rail? A rail going to the graphics or components may not be enough amps. My best guess is the card reader.
For UEFI/BIOS flashing, select your mainboard here and use the forum flash method;
I'll definitely try unplugging some of these USB devices to see if that helps with the B4 hang issue.
As for the PSU, according to the description for it on Newegg: "Four industry-leading independent +12v rails are provided for more stable and safer power output." It has two rails going to the GPU. The GPU is a new addition to the system and so I wasn't running it until recently. The issues were occurring beforehand, but you're right that this PSU is underpowered for the rig considering PowerColor recommends a minimum of 500w. I'm going to be buying a larger capacity one sometime in the very near future. Any recommendations on good modular PSU's? What's a good way to tell what wattage to get?
Thanks for letting me know about the forum flash method. I'll be back later when I have some results.

Z77A-GD65 Intermittent Power Up Issue

Ever since I've had this board, it's been problomatic getting it to start at times. Most of the time it starts just fine, other times the fans just barely spin and it fails to start. Repeatedly pressing the start button usually gets it going after maybe a dozen rapid pressings (think Morse Code).
I've tried jumping the pins on the header on the board, no difference. I've tried pressing the power button on the board, no difference.
Sometimes, however, repeatedly pressing the power button does not get it to start. These times I have to disconnect the power cord and wait for the power button on the board to go out, usually takes 30 seconds or so for the board to totally discharge. Now it will power up right away, I have the BIOS set to power up after a power loss.
Of course I've tried the usual things like one stick of RAM only in Slot 2, different sticks of RAM, only one GPU, no GPU, check for shorts to the case, properly seated CPU, etc. But as it is an intermittent issue, it'll seem fine for a while then go right back to not starting, then start right up the next time without any issues. It will always start with a CLEAR CMOS, but that is not a very handy method of booting the computer.
The system is very stable after it is running, which leads me to think the individual components are not faulty. It never has any problem establishing a restart, only a cold boot. The HEX readout is always A0 when it's running, it's never had any problem booting up after it establishes power.
Board: MSI Z77A-GD65 BIOS 10.5
VGA: MSI GTX 680 Lightning X 2
PSU: SeaSonic 860W (71a 12v rail)
CPU: Intel i7 3770K Ivy Bridge
MEM: Samsung 30nm 2x4gb MV-3V4G3D/US Slots 2&4
HDD: Samsung 830 256gb SSD
COOLER: Thermalright HR-02
OC: Multiplier 4.5Ghz 1.275 CPUV ram: 1800 Mhz 1.43V

Quote from: xmad on 02-August-12, 03:27:35
What is the ME version in bios?
If you remove the OC does the problem go away?
I'm at work right now, not sure about the ME version. Can you elaborate what that is?
OC has no effect, it's been doing this since long before I even attempted to OC anything. It's a fairly random issue. I could, for example, take the OC out and maybe it'd boot issue free for a number of tries, I'd think the issue was resolved. Then, without changing anything, it'll go back to doing it. I had this happen when I read that RAM slot 2 was determined to be the primary slot. I loaded one stick of RAM into slot 2 and got several clean starts. I was convinced I had resolved the issue, only to have it fail on the next attempt.
One thing, time appears to be an issue. I can play around with it in the evening, make multiple cold boots no problem. Then it won't start up in the morning. Or maybe it will start up in the morning, but not at lunch. Or not in the evening. But if it's just a couple or a few minutes, it'll start. And restart.

Z77A-GD65 USB3 port with Seagate Freeagent go desk issues

I have a Z77A-GD65 motherboard, with an intel i5 Ivy Bridge 3570k processor. Kingwin LZP-550 PSU and have attached via USB3 (using a USB3 cable of course) a seagate Free Agent Go Desk 2TB external hard drive.
On my old system the drive when the system is on, is running just spins down when its not in use.. power light stays on for the drive all the time. That was also a USB3 system, just another USB3 chipset.
On this motherboard, sometimes the drive when the system is powered up doesn't turn on and I have to unplug the USB cable and replug it in, after that the drive power LED comes on and spins up.
Any reason why this motherboard is acting like this? The drive should come on with the system like it did on my old system.
Anything I can do to fix this or change the USB ports behavior? It's almost like its not telling the device it's on.

Quote from: xmad on 25-August-12, 00:30:38
Attached is the latest beta bios for your board.(MSI recommended this)
>>Use the MSI HQ Forum USB flasher<<
MSI tried to duplicate the problem but couldn't does this testing procedue seem right to you?
1.   Install System driver and reset
2.   Connect USB HDD to USB 3.0 port. The device can be recognized.
3.   Reboot the system
4.   Check Computer and still can find the USB HDD
5.   Power off the system
6.   Power on and check Computer.
Z77A-GD65
BIOS: E7751IMS.A50
WIN7 64 bit
USB 3.0 driver: 1.0.4.225
Seagate FreeAgent Goflex STAA1500301 1.5TB
I installed that BIOS and still have the issue, one easy way to reporduce this is to power up the system into windows 7 x64, sleep the computer in (sleep mode in bios is set to S3) when you wake it, the USB3 drives are offline

Boot Loop Issues - MSI Z77A-GD65 - Solved

Picked myself up an MSI Z77A-GD65 as well as some Kingston 2x 4GB RAM sticks with a i5 2500k.
After getting everything installed, it just boot-loops on me showing me no boot menu, with a debug code of 55.
If I take out one of the RAM sticks and just use the #2 slot, it boots fine (but after starting windows, it flashes some blue screen and it boots again. I'm thinking that's only because I haven't installed any drivers and still have the old drivers from my motherboard. Yes/No?).
But as soon as I put the second stick in, it will not boot (swapped sticks and it boots fine with one stick). I've tried 1/3 and 2/4 and the only slot that seems to work is #2 (#4 slot won't boot with one stick in it). Tried each stick in each slot. 1/2 work, but 3/4 will not
I'm guessing this isn't a RAM issue but a MOBO issue? I sense an RMA in my future....

Quote from: XFM on 24-December-12, 08:29:56
Can you take a good quality, in focus hi-rez picture of the socket and post it so we can see what you are talking about?
I would if I could. Best way I can describe it is that the pins are all kind of bent at an angle (imagine an L shape, but upside down). Now take the bottom of the L (where it's small and turns) and kind of bend that facing the ceiling. It's kind of like that...
Quote from: Froggy Gremlin on 24-December-12, 08:30:08
Why is this thread in the Intel duo/quad section?
What are the amps on the PSU +12V rail(s)? And how old is it? Suggest to keep just the one RAM stick in the primary DIMM slot and do a fresh OS install with the Mode set to AHCI. BTW, what is the OS? 32 or 64 bit?
Good question. I think I was very tired/annoyed when I made this, and I guess I didn't look properly. If any mods can move it, or need me to take it down, I can.
PSU - http://www.newegg.com/Product/Product.aspx?Item=N82E16817703005
I don't have a problem doing a fresh install, but would like to make sure it's nothing else before hand. If I do a fresh install, and I still have to RMA the board, I would have to do another one to put all my old stuff back in, and I wouldn't really have a PC until the new board came (I mean I could still use it, but would have to re-install stuff and it seems like a bit of a pain if I don't *have to).
64-bit OS

Z77A-GD65 + MSI Control Center (version 2.5.053) = FAN speed control issue

OK,
I've got Z77A-GD65 board and I am using MSI Control Center (version 2.5.053). I have one fan connected to CPU fan header and another fan connected to System Fan1 header on the motherboard. The problem is that while trying to use Smart fan control in MSI Control Center (under Green Power tab) only CPU fan changes speed according to load and the one connected to System Fan1 always stays at the same "System Fan1 Min" set speed. In BIOS the system fan1 is set to auto as all other options are constant speed from 50% to 100%, both fans have 4 wires, so they can change speed. I want both fans to change speed according to CPU load. I know I can use Y (split) cable to connect both fans to the same CPU fan header but I would like to avoid this if possible.
Anybody experiencing the same thing? Issue with bios? Control center bug?

As long as the amps of the two fans doesn't exceed the limit for the CPU fan header, go ahead and use a splitter. Not positive, but believe the fan header amp limit is 1A?

Z77A GD65 - Samsung Green Memory Issue

Hi all,
I have just built my new Ivy Bridge Machine:
MSI Z77A GD65 (BIOS V10.5)
i5 3570K
16GB Samsung Green Memory DDR3 PC3-12800 30nm (4x4GB)
There has been a lot of forum chatter regarding the Samsung Green memory and its incredible overclocking potential. Unfortunately the MSI Z77A GD65 fails to POST at anything above the default 1600MHz. I have tried different RAM timings and increasing the voltage to 1.65V, but nothing got my system to POST.
After doing some forum digging I discovered I am not alone, with other GD65 users having exactly the same problem.
As a result this feels like a BIOS issue with V10.5. Can anyone help?
Cheers,
Matt.

Quote from: Bernhard on 25-May-12, 16:34:48
To OC that RAM higher than 1600 makes virtually no difference to your real performance but adds a lot of potential instabilities. CPU OC yields the real performance gains.
With a Sandy Bridge CPU... I would agree with you.
This is most definitely not the case with Ivy! There are noticeable real-world improvements - if there weren't, I wouldn't be so fussed.
Gigabyte have recognised the similar (same) issue they're suffering with Z77 boards... it's now been a month since anyone replied to me on this issue.
Asus/ASRock do not have this issue - so it's not related to Z77 or the RAM.

No video on MB Z77A-GD65 or GPU

So my last MSI MB killed itself. I received my RMA board and installed it. I have no monitor output from either the MB or GPU output. Any ideas on this one? Cannot see bios info. Grrrr. Thanks.
1 x OCZ Vertex 4 VTX4-25SAT3-128G 2.5" 128GB SATA III MLC Internal Solid State Drive (SSD)
1 x Refurbished: EVGA 02G-P3-1559-RX GeForce GTX 550 Ti (Fermi) 2GB 192-bit GDDR5 PCI Express 2.0 x16 HDCP Ready SLI ...
2 x G.SKILL Ares Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Desktop Memory Model F3-1600C9D-8GAB
1 x Intel Core i5-3570K Ivy Bridge 3.4GHz (3.8GHz Turbo) LGA 1155 77W Quad-Core Desktop Processor Intel HD Graphics ...
1 x MSI Z77A-GD65 LGA 1155 Intel Z77 HDMI SATA 6Gb/s USB 3.0 ATX Intel Motherboard with UEFI BIOS
1 x ABS Majesty series MJ1100-M Continuous 1100W@50°C ATX12V/EPS12V 80 PLUS GOLD Certified, Single 12V Rail, Modular ...
1 x COOLER MASTER Hyper 212 Plus RR-B10-212P-G1 "Heatpipe Direct Contact" Long Life Sleeve 120mm CPU Cooler Compatible ...
1 x Thermaltake Element V Black Edition Steel Full Tower Computer Case Colorshift Fans VL200K1W2Z

Remove the discrete card and clear the cmos, then test the onboad.
If still no vga at all, remove the main board from the case and check for extra stand offs or other shorts. While the board is out, remove the cpu and check the pins with a bright light and hd zoom or magnifying glass.

Z77A-GD65 / Video issues

Similar Messages

Maybe you are looking for