Z87-g45 won't detect video card

I just got a 87-g45 and the on board graphics work fine with my dvi cable. I put in my gtx 660 but it won't detect it at all. I tried putting it in another computer and the card works fine. I saw another thread with a similar problem: https://forum-en.msi.com/index.php?topic=174991.0
I just flashed the bios to the one linked in the thread, but it didn't help. Should I plan to get a new motherboard or is there another way to solve this?

Quote from: XrBob on 29-December-13, 14:23:50
1. The computer runs fine through the onboard video, I'm using it right now to type this. Is it possible that the computer runs fine even with a bent pin? Is it easy to tell if I have a bent pin?
yes it may run fine if a pin that connects to the PCI-E connector is bent! you need to remove the cooler and CPU and look in the underlying socket with a Bright light and a magnifier to see if they are all strait and in line! with each other from a few angles like from above and then at a 45 degree angle to make sure they all look exactly the same!
Quote from: XrBob on 29-December-13, 14:23:50
3. Does that mean having the motherboard just hanging outside the case?
put the board on a piece of plain cardboard or wood (to prevent shorting) on a table and plug up the power and so on and see if it posts there (most builders do that before they put it in a case or place it on the motherboard box itself)!

Similar Messages

Z77A-G45 will not detect video card.

I though that I was having trouble with a new gtx 760sc, so I RMA'd it. On-board video works fine. Still can't detect video card. Bought a new power as well(antec HCG-750). After i received the new video card and still had the same issues I tried out other video cards. Tried two different nvidia cards. One was a 4 series and one a 5 series. Tried in both pci-e slots, and yes the correct power cables were plugged in.

CPU looks fine.
Was finally able to breadboard the thing today. Had the same issues at first. Then I tried the third pcie slot and got post. This one is pcie2.0, so I tried the other slots again. Was able to get the 760 to boot on th second pcie slot. Put the mb back in the case and lost boot on card again. Reseated, same issue. Breadboarded and was able to get the card to post. Still no post in case. Can't see what could be causing a short. Rearranging the risers right now to see if is one of the risers causing a short, or maybe not enough clearance. Any other suggestions would be appreciated.

MOVED: K9N Neo V3 Won't detect video card

This topic has been moved to Linux/Unix.
https://forum-en.msi.com/index.php?topic=137985.0

Quote from: XrBob on 29-December-13, 14:23:50
1. The computer runs fine through the onboard video, I'm using it right now to type this. Is it possible that the computer runs fine even with a bent pin? Is it easy to tell if I have a bent pin?
yes it may run fine if a pin that connects to the PCI-E connector is bent! you need to remove the cooler and CPU and look in the underlying socket with a Bright light and a magnifier to see if they are all strait and in line! with each other from a few angles like from above and then at a 45 degree angle to make sure they all look exactly the same!
Quote from: XrBob on 29-December-13, 14:23:50
3. Does that mean having the motherboard just hanging outside the case?
put the board on a piece of plain cardboard or wood (to prevent shorting) on a table and plug up the power and so on and see if it posts there (most builders do that before they put it in a case or place it on the motherboard box itself)!

H55m-e23 not detecting video card

Hello i recently upgraded my pc with new video card (asus engtx570 directcu ii gtx 570) the problem is that main board(MSI H55M-E23) is not detecting video card, so here is what happens when i turn the pc on it starts to beep 1long beep and 2 short beeps. First i thought it might be power suply so i bought new power suply with 700w and still the same thing happens, then i tryed with LC850w and same thing so i guess the power supply is not the problem. I removed rams and tryed with 1 stick, i have 4 different sticks and same thing happened with each stick. i tested the videocard on different mainboard (ASUS P5Q PRO and ASUS P8H67-M PRO REV. 3.0) and videocard worked fine. i tested my mainboard H55M-E23 with sapphire ATI HD 6950 and it worked too so the pci slot is ok, and now i dont know what to do more i tested all things possible. So what is the problem? my mainboard does not want to detect videocard (asus engtx570 directcu ii gtx 570) 3beeps ( 1long and 2 short) PLEASE HELP!

CPU: Intel® Core™ i5-760 Processor Clock Speed 2.8 GHz Max Turbo Frequency 3.33 GHz
Main Board: Msi h55m-e23 Bios: AMI BIOS Version 17.4
Video Card: Asus GeForce ENGTX 570 Direct Cu II
Memory: Kingston 1x2GB 1333MHz DDR3 CL9 DIMM 1.5V
Apacer 1x2GB 1333Mhz DDR3 CL9 1.5V
PSU: LC 850W Arkangel LC8850, 140mm FAN, V2.2
850W max., ATX V2.2, Free-Plug cable-Management, Active-PFC, 3 x PCI-Express, 4 x +12V: 60A, S-ATA,
+3,3V: 30A
+5V: 28A
+12V1: 18A
+12V2: 18A
+12V3: 18A
+12V4: 18A
HD: Seagate Baracuda 7200 - 320GB
Windows 7 x64
For the memory ( i did try with only 1 stick at the time... they go well together with my other card Sapphire ATI HD 6950)

IMac won't detect SD card

My iMac won't detect any SD card's. It doesn't seem to matter the size (2GB-16GB) or brand, it is just like I haven't inserted one. I have never used one with it before so it isn't from failing to "safetly remove hardware" and I have tried cleaning the slot (with air can)

Have you checked to see if the SD card reader is listed in system profiler? (apple menu, about this mac, more info button) it should be listed under Hardware, under USB, it would be labeled some thing like "Internal Memory Card Reader".
If the card reader isn't listed:
Have you tried a NVRAM Reset?
Have you tried a SMC Reset?
If the card reader is listed, but your not seeing the inserted cards:
Have you checked to see if the cards are reconised in Disk Utility? (go to the dock, click on finder, go to the menu bar, click on the go menu, chose Utilties, double click on disk utility) Do you see the sd card listed?

Detect video card in 32 and 64 bit.

How can I get both the 32 and 64 bit versions of CS6 to detect my graphic processor (AMD Radeon HD7700) for GPU usage in Win 7 ? Cuiurently, it is only seen in 64 bit.

Thanks again Chris.
I again completely uninstalled the AMD Catalyst and drivers and reinstalled the latest one from their site. I am still unable to select Again, the card is not detected in the 32 bit version of CS6 and is readily available in 64 bit. Also very interesting is what the System info shows. i.e. Windows XP and yet I installed the lastest version of CS after I had updated to Win 7 on a new computer.
Here's what the system info shows in CS 6 32 bitr ..
Adobe Photoshop Version: 13.0.1 (13.0.1.2 20130522.r.24 2013/05/22:21:00:00) x32
Operating System: Windows XP 32-bit
Version: 5.1 Service Pack 3
System architecture: Intel CPU Family:6, Model:10, Stepping:9 with MMX, SSE Integer, SSE FP, SSE2, SSE3, SSE4.1, SSE4.2, HyperThreading
Physical processor count: 4
Logical processor count: 8
Processor speed: 3403 MHz
Built-in memory: 16344 MB
Free memory: 12841 MB
Memory available to Photoshop: 3255 MB
Memory used by Photoshop: 62 %
Image tile size: 128K
Image cache levels: 4
OpenGL Drawing: Disabled.
OpenGL Drawing Mode: Normal
OpenGL Allow Normal Mode: True.
OpenGL Allow Advanced Mode: False.
OpenGL Allow Old GPUs: Not Detected.
Video Card Vendor: ATI Technologies Inc.
Video Card Renderer: AMD Radeon HD 7700 Series
And here's what it shows in CS 6 64 bit version ...
Adobe Photoshop Version: 13.0.1 (13.0.1.2 20130522.r.24 2013/05/22:21:00:00) x64
Operating System: Windows 7 64-bit
Version: 6.1 Service Pack 1
System architecture: Intel CPU Family:6, Model:10, Stepping:9 with MMX, SSE Integer, SSE FP, SSE2, SSE3, SSE4.1, SSE4.2, HyperThreading
Physical processor count: 4
Logical processor count: 8
Processor speed: 3403 MHz
Built-in memory: 16344 MB
Free memory: 13122 MB
Memory available to Photoshop: 14730 MB
Memory used by Photoshop: 71 %
Image tile size: 128K
Image cache levels: 4
OpenGL Drawing: Enabled.
OpenGL Drawing Mode: Advanced
OpenGL Allow Normal Mode: True.
OpenGL Allow Advanced Mode: True.
OpenGL Allow Old GPUs: Not Detected.
Video Card Vendor: ATI Technologies Inc.
Video Card Renderer: AMD Radeon HD 7700 Series
In my powerful mind, it appears that CS will only see the card in the 64 bit version. Not that it's a big problem with easy work-arounds but it puzzles me and I was hoping that someone else has had a similar experince and was willing to chime in.
Appreciate your time.

Cannot Detect Video card (Radeon 6750m)

Dear sir,
I would like to know why my laptop cannot detect my video card (Radeon 6750m). It only shows the built in graphic card intel. I already try to use system restore and reset to original factory mode. It will appear but after updating my drivers and reboot my laptop. My laptop cannot detect again the video card.
Please help me resolve this problem,
for you reference
http://tinypic.com/r/2it67ex/8
This question was solved.
View Solution.

You will have to enable the Radeon HD adapter by using the Catalyst Control Center.
Once you do that the adapter will appear in the Device manager.
If you are using the Intel HD graphics, only the Intel graphics will be seen in the Device Manager.
I know that may sound strange, but it is one of the pecularities of having a switchable graphics capable notebook.
The following URL goes to an overview of switchable graphics. Take a few minutes and read it. It should help make understanding it simpler.
http://support.hp.com/us-en/product/HP-Pavilion-dv4-Entertainment-Notebook-PC-series/5048648/model/5...
Do not instal the Intel graphics driver seperately!
Doing that breaks the switchable graphics feature.
Only install the HP ADM ATI graphics softpaq. It will install both drivers automatically and let you use the switchable graphics featrure og your notebook.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

10.4.7 won't detect EDVO Card

I purchased a Sprint Merlin S720 Mobile Broadband card. According to Sprint I had to initialize the card in a PC with Win XP then insert the card in my Powerbook.
The card worked fine in the PC, but when I inserted the card in my Powerbook it didn't detect the card. The card lit up and a card icon showed on the top bar next to my Airport icon, but when I click on it it indicates "Unknown Vendor". The only workable option there is to turn off the card.
When I go to "Internet Connect" application, or in Preferences "Network" there is no indication that the card is there. When I to "About this Mac" "More Info" the Hardware PC Card section shows vendor Unknown and the USB section of Hardware shows USB Bus, Novatel Wireless CDMA.
????????

The Sprint 5740 card will work without a hack... on my powerbook g4 15", running 10.4.7, I had the same problem you had. Somewhere I read to use "#777" for the phone number in Network setup, use the actual card phone number for Phone Number, and the 6 digit NPA/NXX number from Sprint for the password. Select Sprint PCS Vision for the modem, and it's done. I couldn't believe it, after 4 hours of trying.
Powerbook G4 Mac OS X (10.4.6)
Powerbook G4 Mac OS X (10.4.6)

Z87-G45 won't reboot?

Hello all!
I recently finish my build, and upon initial testing my MSI board booted into BIOS. Without changing anything, I turned it off and went to dinner. Upon returning, I plugged in my cd drive and hdd to try and get an OS and now I have no output. I tried reseating the video card, moving the hdmi input directly to the motherboard, unplugging the other components and USB stuff....nothing. I even tried taking the mother board battery out and putting it back in after 10 minutes out of desperation.
Is there anything I'm missing here or is my motherboard mysteriously shot?

Try the card in the second slot, if that is of no help, flash the bios to the most recent release and retest.
>> BIOSes<<
If still no help, try the card in another computer or another card in your computer to verify where the problem lies.

No detect video card

Hallo i would like to post a problem when my computer boots up i get message using pcei gen 1then it says cant find device and then boots furtherinto
vga graphics mode i have a pce video card in pci 16 slot. I have in bios set as primary pce and internal video turned of .I hope someone can give me advice here are my specs taken with live update
Operating sys Windows 7 64 bit
Motherboardmodel 760ga-p43fx ms-7699
Curent Bios Ver 1.20
Graphics card standaard-vga adapter But i have msi hd 7750
Psu XFXpro 550Wat
I thank you

>>Posting Guide<<

T520 won't detect Network card in WDS/WinPE/Ghost image disk

Hello all,
I figured I would just post this so I could save 2 days of someone elses life.
I'm not sure how many other modes have the EFI and UEFI bios's in them but this has caused a lot of problems when trying to capture an image / image the Lenovo T520. So for anyone else that is having these problems here is how I got around the problem.
The Problem:
While trying to boot up off a Capture image with a CD or PXE boot for our WDS server the laptop would not detect the network card giving no IP address and listing the adapter as a hybrid. When trying to do a ipconfig /renew it would give an error around the lines of the loopback something or other ....... the adapter could not be contacted or initated.
I instantly thought this was due to the vanila WinPE / Capture image not having the drivers for the Lenovoo T520, so I went to the website downloaded the new drivers and injected them into the WinPE disk(You will want ot use the NDIS Drivers which are included in the package for this). Following this process it would still not detect or install the NIC. After many hours of searching it would apear this was due to the EFI/UEFI bios options not going through the proper boot cycle when in a PE enviroment. The solution was to mess around with the EFI/UEFI switches in the WinPE boot image during the creation proccess as listed below:
ocdimg -m -o -u2 -udfver102 -bootdata:2#p0,e,bc:\winpe_x64\etfsboot.com#pEF,e,bc:\winpe_x64\efisys.bin c:\winpe_x64\ISO c:\winpe_x64\winpeuefi.iso
The link with more details is here: http://support.microsoft.com/kb/947024
Eseentially once the new boot image was complied with the proper EFI / UEFI options enabled it went through the proper boot process detected the NIC and installed the drivers which I previously provided on the disk and we where off to the races imaging the new laptop.
Hopefull this will help some others who are struggling with this or any other model that has this type of bios.
Cheers, and thanks
Please feel free to post any additional comments to help others if you found better ways to get around this
One side note the EFI/UEFI to legacy mode only does nothing for the NIC problem, I have seen some posts where they can help with the hard drive issues when imaging, however as for the nic not loading in PE enviroments this setting in the BIOS did not reslove the problem.

Hi Rusty1234
If I did not remember wrongly, you may present or add drivers (network, hardware) under WDS / Ghost software or copy necessary drivers (e.g. your T520 network card drivers) under it's PXE / boot section.
Happy 2012!
Peter
W520 (4284-A99)
Does someone’s post help you? Give them kudos as a reward, as they will do better to improve | Mark it as solved if the solution works for you, so it could be reference for others in the future
=====================================
Sound Enthusiast and Enhancement (Post comments, share mixes, etc.)
http://forums.lenovo.com/t5/General-Discussion/Dolby-Home-Theater-v4-for-most-Lenovo-Laptops/td-p/62...

Photoshop CS5 64-bit does not detect Video Card

I just updated from CS4 to CS5. I have a core i7 with an ATI HD 5700 series graphics card with the most recent driver 10.9. Photoshop is also updated to 12.0.1. For some reason, only the 64-bit version does not detect the graphics card. Photoshop CS4 64-bit and Photoshop CS5 32-bit see the graphics card fine. I noticed a few others have had the same issues. Has this problem been addressed yet? If not, is there a workaround?

It's a recently-reported issue with Catalyst 10.9 on the Radeon 57xx.
See this thread: http://forums.adobe.com/message/3184458
-Noel

IPod Won't Detect Video

hello, my video iPod will not detect that a video is video and categorizes it as a music file, and when I select "get info" on the particular video, all the tabs (summary, info, options, lyrics, artwork) are all available except the video tab. I can't make my iPod detect a video if this tab is not available for selection. So how do I get the iPod to detect these videos and not play them as simply audio files with no visuals
basically my iPod puts all the videos in the audio playlist and I want to know how to get my videos out of the audio playlist and into the video playlist as none of them show up in the video playlist

You might want to try a different port on your computer. Also check with a different cable. I know I've personally run in to issues with a bad USB port, it will read a keyboard/mouse just fine, but if I try it with an external drive or iPod, nothing.

HELP!!! iPhone randomly reset and now it won't detect SIM card?

Ok so here's what I was doing when this all happened.
I had called the Linksys support for a new router I just bought that wasn't working right. After waiting about 8 mins I was connected to a gentlmen in India, we worked on my problem for about 10mins or so and then all of sudden my phone just reset, or at least went to the apple logo and just sat there.
then after 30 seconds it started ringing (before it fully restarted) and it was the tech gentlemen call me back. So I slide the thing to answer and the screen froze with the slider on the right but not unlocked but I could see the time and my back ground, just no buttons and I could still hear him and talk to him.
After we fix my problem with the router he hung up, but my phone was still froze and then it started ringing (a friend had tried to call me before it reset while I was on the phone so I assume it was him again). I couldn't answer and it just kept ringing and ringing so I held the wake button and slide the red slider to shut it off.
Left it off for 30 seconds or so then press and held it again to turn it on. Now it says restore need, connect to itunes!
ok, so I did and after wait about 30sec to a minute after connecting it to itunes it comes up with this error:
*"iTunes cannot activate your iPhone because the SIM card is not inserted or a SIM PIN is required. Disconnect your iPhone, make sure the SIM card is inserted correctly and, if you use a SIM PIN, tap Unlock to enter it, and then reconnect your iPhone."*
What the heck?! I've had it randomly reset once before about a month and a half ago and which point I did have to restore, and it did and it worked fine after that.
The SIM card IS in there, and I have no idea what my SIM PIN would be, nor do I see the option for it they speak of! And this happened about 9:30pm, well after any Apple or AT&T stores are closed! I even turned off the phone, took the SIM card out and put it back and it still did the same thing!
What would cause this to randomly just mess-up like this? I loved this phone when I got it but now that this is the 2nd time this has happened and much worse I'm pretty ticked about it. And it's not like I hacked it or unlocked it or whatever that is even called, the only things I've put on my iphone are music, pictures, and programs I all got thru itunes!
PLEASE HELP!

Hi Guys,
I'm writing this from the UK. Got an iPhone 3G bought a few weeks ago and activated (no jailbreak or other stuff)it. It worked fine but last night it gave the same error as originally reported in this thread.
Went into the O2 store (this is the provider selling iPhones in the UK) and they told me is the SIM card. Got a new one but still the same...
There is something going on here because I've seen lots of claims with the exact same description. Its almost like there is a bug in the software that gets activated on the 3rd of January.
Will go tomorrow again and ask for a new phone.

T400 won't detect WWAN card

Hello all,
I am a newcomer to this forum and I'm glad to see such support for such great products!
I just got my first ever ThinkPad after some research - the T400. I bought it equipped with this:
SBB ERICS.F3507GUSA-WIWANCARD
I noticed immediately that the SIM card was installed in already, so I powered it on, but in the Lenovo Welcome center part, it told me that I do not have any kind of mobile broadband card installed.
What?
I see the slot for the SIM, and I have a guy on Tech Support telling me it's a PCMCIA card and that I need to pull it out and put it in again!
I've already tried reinstalling the drivers, etc. Did I just get a defective card? Has this happened to anyone else?
Thanks for your help
Spencer

Have you checked to see if the SD card reader is listed in system profiler? (apple menu, about this mac, more info button) it should be listed under Hardware, under USB, it would be labeled some thing like "Internal Memory Card Reader".
If the card reader isn't listed:
Have you tried a NVRAM Reset?
Have you tried a SMC Reset?
If the card reader is listed, but your not seeing the inserted cards:
Have you checked to see if the cards are reconised in Disk Utility? (go to the dock, click on finder, go to the menu bar, click on the go menu, chose Utilties, double click on disk utility) Do you see the sd card listed?

Z87-g45 won't detect video card

Similar Messages

Maybe you are looking for