Z87 MSI Mpower Max Adaptive vcore not working properly?

Hi, first time MSI MB user here.
After I finished tweaking my OC settings, I changed the vcore voltage from fixed to adaptive mode, since that is said to lower the idle temps.
However, it doesn't seem to work in the way that I thought it would.
Vcore voltage stays at the same value regardless of whether the CPU is idle or under load. I thought it would lower itself when the CPU is idle.
Am I misunderstanding something here?
Voltage check done by AIDA64 and CPU-Z 1.64.3
Below are my bios settings:
BIOS ver. 1.1
CPU Ratio Mode - Dynamic
Adjust CPU Ratio - 45
EIST and Turbo boost -enabled
Adjusted Ring ratio - auto (39x)
Adjusted Ring Frequency - 3900Mhz
VCCIN Voltags - 1.95V
CPU Core Voltage Mode - Adaptive
CPU Core Voltage - 1.25
Thanks.

Quote
Once the CPU V. is taken out of auto and set manually, the voltage isn't going to drop at idle.
Quote
That's not what I was led to believe?
Yup! Turns out your belief is correct. The rules 'have' changed with Z87!

Similar Messages

MSI 865PE NEO FISR2 Audio not working properly

The audio on my board is not working properly. I have it set for 6 channel and am using Creative Labs Inspire 5.1 Speakers that have 3 inputs that match the 3 output jacks on the mobo. However, its just not right. It is sending anything to all 5.1 speakers and also to the proper speaker at same time. So every sound is coming through all speakers and it a tad louder on the speaker it should be coming out on. Anyone else have any clue as to what setting I can change to correct this or is this something wrong with the cmedia drivers?

The answer to all your suggestions is yes, already did it and in the demo app the sounds work fine. Its just so odd, I may just go to Circuit City tomorrow and buy another set of speakers and see if it is possibly them that are causing the issue. Then if so, I'll just return the Creative Labs ones as I just bought them 2 weeks ago and CC has great return policy
Actually, one of your questions I did not either understand what you meant or did not see the option Quote
Did you enable the output port correctly - LR to LR, surround to surround, center/lfe to center/lfe
The only thing I see is setting phones, 2, 4 or 6 channel in the cmedia control panel and then I plugged in the proper cables.

AC adapter light not working

When charging my Macbook Pro sometimes the indicator LED light doesn't come on at all. Everytime I checked when the LED isn't working the computer still charges, but I am not sure if when I leave it sometimes if it is charging correctly since the LED doesn't work periodically. I am also wondering if this is an issue with the adapter, rather then the actual computer port. If it is the computer port I don't feel comfortable with sending it out for repairs if its just a small issue. I guess what I am trying to see is if anyone else has experienced this issue. I would much rather go to the apple store and recieve a new adapter, and if the issue persists I can send it in for repairs. Please if anyone has experience with the same trouble I have had let me know. Thank you in advance.
-Andrew

May be the adapter is not working properly.
Take the MBP and MagSafe/Power Adapter to the Apple store for evaluation.
For:
The MagSafe power adaptor LED doesn't appear to indicate the correct activity.
Reset SMC. http://support.apple.com/kb/HT3964
Choose the appropriate method.
Best.

Bootcamp 3.2: Microsoft Virtual WiFi MiniPort Adapter shows "device is not working properly...Code 31"

Using Windows 7 Enterprise 64-bit, Microsoft Virtual WiFi Miniport Adapter shows the "device is not working properly because Windows cannot load the drivers required for this device. (Code 31).".The device is the Apple iMac10,1 All-in-one computer. Right clicking browse files (for the device) shows the Bootcamp (C:), DVD (D:); and my external hard drives can be selected.
Internet and WiFi connections all working ok. Am also running MacDrive 8 to access the Mac drives when in the Windows partition, again without any seeming issues.
Updating the driver simply generates another Code 31 error.
Appreciate this seems to be a known problem - is the a solution a novice use might be able to follow or should I simply ignore the error message?
Driver Date us 21/06/2006 and Driver Version is 6.1.7600.16385.

Hi ,
Thank you for visiting the HP Support Forums and Welcome. It is a great site for information and questions. I have looked into your issue about your HP ENVY 4-1204tx Ultrabook and issues with WiFi adapter is not working properly. Error codes in Device Manager in Windows 8.1 could be fixed by deleting any extra drivers. So I would uninstall all that is listed in the Network drivers in the Device Manager, restart the Notebook. Here is a list of Device Manager options, this might help.
Here is a link to the HP Support Assistant if you need it. Just download and run the application and it will help with the software and drivers on your system that need updating or reinstalling. Hope this helps. Thanks.

[SOLVED] Configuring SPDIF for MSI Mpower MAX

Hi people of the Arch,
I would like to play music over SPDIF, while I get no errors, I also get no sound.
I have read the Wiki here Advanced_Linux_Sound_Architecture
Also, I've been Googling and searching here on the forum, I've followed some steps but none seem to 'sound' right.
What I have not done is creating an asoundrc file with my setup, I believe that I can test if it works first, before I create such a file. Like to hear if this is right.
And I should note that I also use regular stereo out and USB headphones.
Attempt to play wav
@ThijsPC .:19:23:. {thijs}>aplay -D iec958:CARD=PCH,DEV=0 booze.wav
Playing WAVE 'booze.wav' : Unsigned 8 bit, Rate 22050 Hz, Stereo
aplay: set_params:1233: Sample format non available
Available formats:
- S16_LE
- S32_LE
Second attempt with bit-rate and new file
@ThijsPC .:19:35:. {thijs}>aplay -D iec958:CARD=PCH,DEV=0 Yamaha-SY-35-Clarinet-C5.wav -f S16_LE
Playing WAVE 'Yamaha-SY-35-Clarinet-C5.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
No error and no sound..
Third attempt with addressing using hw:0,1 and not the alias
@ThijsPC .:19:41:. {thijs}>aplay -D hw:0,1 Yamaha-SY-35-Clarinet-C5.wav -f S16_LE
Playing WAVE 'Yamaha-SY-35-Clarinet-C5.wav' : Signed 16 bit Little Endian, Rate 44100 Hz, Stereo
No error and no sound..
My motherboard:
MSI MPower Max
Receiving device:
Marantz NR1403
aplay -L
null
Discard all samples (playback) or generate zero samples (capture)
pulse
PulseAudio Sound Server
default
Default ALSA Output (currently PulseAudio Sound Server)
sysdefault:CARD=PCH
HDA Intel PCH, ALC1150 Analog
Default Audio Device
front:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
Front speakers
surround21:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
2.1 Surround output to Front and Subwoofer speakers
surround40:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
4.0 Surround output to Front and Rear speakers
surround41:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Analog
7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
iec958:CARD=PCH,DEV=0
HDA Intel PCH, ALC1150 Digital
IEC958 (S/PDIF) Digital Audio Output
hdmi:CARD=HDMI,DEV=0
HDA ATI HDMI, HDMI 0
HDMI Audio Output
hdmi:CARD=HDMI,DEV=1
HDA ATI HDMI, HDMI 1
HDMI Audio Output
hdmi:CARD=HDMI,DEV=2
HDA ATI HDMI, HDMI 2
HDMI Audio Output
hdmi:CARD=HDMI,DEV=3
HDA ATI HDMI, HDMI 3
HDMI Audio Output
hdmi:CARD=HDMI,DEV=4
HDA ATI HDMI, HDMI 4
HDMI Audio Output
hdmi:CARD=HDMI,DEV=5
HDA ATI HDMI, HDMI 5
HDMI Audio Output
sysdefault:CARD=P780
Plantronics GameCom 780, USB Audio
Default Audio Device
front:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
Front speakers
surround21:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
2.1 Surround output to Front and Subwoofer speakers
surround40:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
4.0 Surround output to Front and Rear speakers
surround41:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
4.1 Surround output to Front, Rear and Subwoofer speakers
surround50:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
5.0 Surround output to Front, Center and Rear speakers
surround51:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
5.1 Surround output to Front, Center, Rear and Subwoofer speakers
surround71:CARD=P780,DEV=0
Plantronics GameCom 780, USB Audio
7.1 Surround output to Front, Center, Side, Rear and Woofer speakers
aplay -l
**** List of PLAYBACK Hardware Devices ****
card 0: PCH [HDA Intel PCH], device 0: ALC1150 Analog [ALC1150 Analog]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: PCH [HDA Intel PCH], device 1: ALC1150 Digital [ALC1150 Digital]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 3: HDMI 0 [HDMI 0]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 7: HDMI 1 [HDMI 1]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 8: HDMI 2 [HDMI 2]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 9: HDMI 3 [HDMI 3]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 10: HDMI 4 [HDMI 4]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 1: HDMI [HDA ATI HDMI], device 11: HDMI 5 [HDMI 5]
Subdevices: 1/1
Subdevice #0: subdevice #0
card 2: P780 [Plantronics GameCom 780], device 0: USB Audio [USB Audio]
Subdevices: 1/1
Subdevice #0: subdevice #0
[edit]
Receiver was broken, replaced, config above is good.
Last edited by Thijxx (2014-11-17 07:55:21)

Try this one, v1.2B8;
https://forum-en.msi.com/index.php?topic=169759.msg1240621#msg1240621
Mine originally came with v1.1 and had no problem booting or restarting problem of holding settings above stock/auto/default.
Quote
What happens is that it will make it past the start orbs and I see the mouse with a black background and then it BSODs. The computer restarts again and then boots properly.
Usually an indicator a voltage isn't high enough. OC settings don't sound stable. Might open a thread in the OC and Undervolt forum section for help with that. I've stayed away from the DRAM Training (left it as is) and reached 2800 without any trouble. Not all IMC's are going to handle that speed though from what I've been reading. All my benchmarks so far are showing RAM speed above 1600 adds little performance value.

MSI Mpower Max 4770k Help tweek it

Hi there,
this is my first seriouse MSI board in last 3years and i have encountered few problems with overclock
My Pc Specs are:
Intel 4770k
Corsair H70 with 2xNoctua 14FLX p/p
MSI Mpower Max
Kinston Hyper X DDR3 1600mhz 9-9-9-27 2x4GB
Corsair AX860
Intel SSD 510 250GB
Seagate Barracuda 3TB
Samsung F4 2TB
Corsair 650D
all day passed and i am a bit tired of seeing bios and bsods
i think i got the lazy chip help me understand it better and learn things on the way.
this is most stable i got.
Bios E7815IMS.133
CPU ratio: x44
Ratio: Fixed
Ring: x39
Vcore 1.25v Offset 0.015V
Svid comm. Enabled
from digitall i changed only CPU Vdrop to 100%
Ram set on xmp and manualy entered timings and voltage and speed 1600
With this i pass AIDA 64 stress test for 30min no problem
cinebench pass
when i open Prime95 Blend test 15min pass and bsod..
Temps were 80-85c with room 25c
Everything else in bios is set to default (auto)
Any tips how to tweek it more?
i tried x45 with settings as above i boot into windows pass cinebench but crash on aida64.
i also tryed just x46 with voltage bump up to 1.28v with offset 0.015
I will be deliding as soon as my h220 arrives and CLU.
Also is there some special USB so i can take the screenshots?
i tried all the ports different flashes also formated to FAT32 and NTFS same its saying no usb dongle..
When i put my WD 2TB HDD it recognize it but when i want to save the Screenshot it gives this message
"allocate file system resource fail"
I would post Screanshots but as i mentioned above its annoying problem..
Thanks in advance guys.
Edit:
just to see if i have lazy chip i tryed 1.3v with settings above and x47-48 wont even post.... :(
found flash that is working

ok i tryed this also
Internal VR efficiency management - disabled in screanshots its enabled
with this i am able to make 30mind aida with no crash temps a bit high but can be managed, i boot into windows with this vcore and x45 but unstable during aida 10min bsod
i boosted the voltage to 1.275 with offset 0.015v and got me 20min aida then bsod. any way i can tweek it more?

Ac power adapter is not working

i bought this item apox. 9/10 months ago from Tesco so i dont know if i have any cover?
HP Photosmart Plus All-in-One Printer - B209a
ac power adapter is not working and i ready own hp printers and dont want to have to splash out on another.
please help...
This question was solved.
View Solution.

Hi,
You should still be under warranty, but if not you should be able to buy one from HP Parts Surfer.
I hope this helps
JonW
I work for HP

RFC adapter in XI 3.0 not working properly with BAPI in R/3 4.6C

Here is the scenario.
An XML file is received from our customer. This file contains purchase order information that is used to create a sales order in our SAP 4.6C system. Once the sales order is created an acknowledgement is generated and this is returned back to our customer in an XML format. This scenario is working perfectly fine in our XI 2.0 system but is not working properly in our XI 3.0 test environment. Our custom function module in R/3 is a wrapper function that uses a standard SAP BAPI to create the sales order. Part of the function module does use the statement
call function 'BAPI_TRANSACTION_COMMIT'
The last thing the BAPI does is call another function module that using an RFC destination that will return and order acknowledgement.
Here is what happens within XI and our SAP system.
The XML file is received and mapped to our imported RFC. The RFC adapter is called and the information is passed onto SAP where our customer function module executed. The sales order is created within SAP without any problems and the second function module is called which references an RFC destination assigned to our XI 3.0 system. The information is sent back to XI and an appropriate file is created for our customer. All seems to be working properly except that when the original RFC is sent from XI to SAP, SAP creates a short dump stating
"call to messaging system failed: com.sap.aii.af.ra.ms.api.DeliveryException:" Then it is put back into the que where 5 minutes later it executes again and trys to recreate the sales order in SAP. (again, this same function module executing from XI 2.0 works fine)
I believe I have everything configured properly because the SAP side is being executed and I am successfully passing information back from SAP to XI. However the original function module in SAP is failing with the above error message. It appears that the original function module cannot communicate back with XI. I have had SAP looking at this issue and they have not been successful yet in solving this problem.
Any ideas.
Thanks,
Jim d'Hulst

Hi,
I think the problem is with the send back of acknowledgement to XI. Does the DeliveryException state something about the sender agreement? I guess you are using a statement like below:
CALL FUNCTION 'ZABCD'
destination <tcp/ip destination>
exporting
input = ack.
In that case, check whether the TCP/IP destination is working fine. Also, to be able to exchange message, the structure of the Function Module ZABCD needs to be identified as the sender in XI Configuration (Integration Directory).
Also, check your config with the blog mentioned below:
<a href="/people/arpit.seth/blog/2005/06/27/rfc-scenario-using-bpm--starter-kit">/people/arpit.seth/blog/2005/06/27/rfc-scenario-using-bpm--starter-kit</a>
Regards,
Amitabha

Apple av adapter does not work after updating ios 5,01

apple av adapter does not work after ios 5,01. no video on vga monitor. sound goes out on iphone 4 also.

Thank you for your interest. Last night i tried again. It worked. there is still problem, so i could find out it that monitor is going to power saving mode then voice goes out and no view on monitor. I changed the power saving settings. And worked well. Thnx again.

Pick activity is not working properly while creating two or more file adapt

Hi,
pick activity is not working properly while creating two or more file adapter for bpel process.
bpel process compiled and deployed succesfully but while observing the wsdl file of deployed process you can find only one file adapter. so it polls only from that location.
can anybody help on over this? or it's limitation of jdev to use only one file adapter at time while using Pick.
Thanks
sagar

Does anybody tried this?
Thanks
sagar

Laptop adapter in not working

laptop 420 se.mo-5CG10706HG
this laptop charger is not working

Hi
Please call HP Technical support check your warranty incase your sure the Adapter is not working get it replaced.
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

Max Memory Settings Not Working (SQL Server 2008 R2)

I have 12 GB ram in sql server 2008 R2 of 64 bit server (Windows 2008 R2).
I have set the Max memory setting to 12288 MB Memory setting.
Still the usage of sql server process is around 14 GB.
Is Max memory setting not working?
I have also enabled AWE after all it is 64 bit.
Thanks

Problem is that: my OS is halting due to this RAM. I have 16 GB of ram and assigning 12 GB to SQL SERVER and rest is using for OS. Please guide me how to get information about actual memory usage from all sql server processes. like
all CLR etc
Hi,
Are you also running SSIS/SSAS/SSRS with database engine services. What do you mean by OS is halting ?
If you want to check whether SQL Server is facing memory crunch please have a look at perfmon counters from
this link
Sys.dm_OS_memory_clerks would be DMV helpful in tracking memory utilized by various processes
I have also enabled AWE after all it is 64 bit. Thanks
Please note AWE doe snot have any notable affect in 64 bit system.
Below will tell you memory used by SQLCLR
select single_pages_kb + multi_pages_kb + virtual_memory_committed_kb from sys.dm_os_memory_clerks where type = 'MEMORYCLERK_SQLCLR'
Below query will give you memory consumed by various clerk
SELECT type, SUM(multi_pages_kb)
FROM sys.dm_os_memory_clerks
WHERE multi_pages_kb <> 0
GROUP BY type
ORDER BY SUM(multi_pages_kb) DESC
Can you reduce max server memory to 11 G and see if it gives some relief
Please mark this reply as answer if it solved your issue or vote as helpful if it helped so that other forum members can benefit from it
My Technet Wiki Article
MVP

HP Pavilion Power Adapter Beeping/Not Working

I just made a post earlier tonight about how my HP Pavilion dv7-1014ca Entertainment Notebook was running too hot. Well now I've got bigger problems.
The battery on my laptop has been shot for a while now. My notebook isn't even 2 years old yet and I've gone through3 batteries. For whatever reason, they just aren't lasting. Last year I also had issues with my power jack not working properly. I got it repaired last summer, but in the past two months, it seems as if the issue has returned. Sometimes when I move the chord, the power supply cuts out. Also in the past month or so, my power adapter has been making this annoying beeping noise whenever I plugged it in. It would usually go away if I fiddled with it, but as of right now, I can't get it to stop, short of unplugging the thing. As it stands, the power adapter no longer seems to work, and since my battery is shot, my notebook has turned off. With no battery and no external power source, my laptop is unusable.
So... is the adapter fried? Is my power jack toast again? Seeing as my PC is no longer under warranty, what are my best options for replacement parts/fixes?

Hello @pxj,
I understand that your notebook's keyboard is not working, and that your alternative keyboard does not function as well. I would be happy to assist you in this matter!
Since your system's available drivers do not contain any keyboard drivers for Windows 7, I recommend obtaining a recovery disc to re-install Windows Vista on your system. This can be done by following this document on Obtaining HP Recovery Discs or an HP USB Recovery Drive.
Please re-post with the results of your troubleshooting, and I look forward to your reply!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Windows 8 Wireless Adapter do not work?

Well, i just installed windows 8 but my wireless adapter do not work ;(! I have a hp 802.11b/g wireless network adapter! I got an HP Pavilion a6023.sc stationary PC! Please help asap!
//Kevin
This question was solved.
View Solution.

Hi:
This is the only thing that I can think of that will work...see if manually installing the Vista 64 bit driver works on W8.
Run this driver. If it installs automatically, great. If not...
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=pv-65991-1&cc=us&dlc=en&lc=en&...
Go to the device manager and click on the network controller needing drivers.
Click on the driver tab. Click on Update Driver. Select the Browse my computer for driver software option and browse to the driver folder that was created when you ran the file.
That folder will be located in C:\SWSetup\sp34931. Make sure the Include Subfolders box is checked and see if the driver installs that way.

Satellite Pro U200: VGA output not working properly when AC adapter was connected

Hi,
I have a problem with vga output. When I'm working on battery and connect my notebook to external monitor it's ok, but when I connect AC adaptor then start waving also bluetooth and wlan does not work properly. In other case when I remove battery from notebook and connect AC adaptor it works properly.
thanks in advance

As long as you use a CRT you should set the refresh rate new, at least 85Hz. Standard is 60Hz as far as I know, and that hurts in your eyes.
The wireless lan behaviour is quite normal as long as your not right next to the access point. On battery power the wireless lan card reduces its energy consumption thus the connection will be poor if you dont have a perfect signal. You can turn this off in the iNTEL Pro/SET wireless software, where you can configure the adaptor. Try to change the powersafe mode to manual and full power, this should solve your problem.

Z87 MSI Mpower Max Adaptive vcore not working properly?

Similar Messages

Maybe you are looking for