Z87 XPower Board and multiple Single video cards?

I'm lost and can't find an answer anywhere. I use 3 video cards to connect to 6 monitors but for some reason this mobo won't recognize any of my other cards except for the one in PCI_2 since that's wired to the CPU directly... I need to get the other ones working too how can I do this? I checked the CeaseFire switch and they're all set to "On" so they should be working, but alas they are not. Hopefully someone can help me figure out what I am doing wrong.
BTW, these are standalone cards, not crossfire or sli capable.

Quote from: XFM on 29-June-13, 10:27:36
Not that it make much difference to any of us but just out of curiosity why do you need that many cards and 6 displays?
I'm a multi-tasker. I'll have Adobe Premiere running on my primary display, After effects on a neighboring screen, browser in another, e-mail client in another, dreamweaver in another, and I have the final screen designated so I can fly through the files I need to find for easy drag and drop utilization. It's just the setup I like to use more than anything.
Anyway I got it to work finally in Slots 1, 3, & 7. After my last post I rebooted with no cards, added them into slots 1, 3, 5 and then magically the drivers were installed for them. I didn't do anything different which is why I am still a bit confused, but it is working now.
Anyway, time to troubleshoot my last issue. HDD in SATA slots 1-8 work fine but when I add drives to 9 & 10 my computer won't boot, it'll only show a flashing underscore. Kind of like the old issue where a WD external drive would do that on boot... but, anyway I can start a new thread for that if need be.

Similar Messages

  • Multiple X1900XT video cards?

    Can someone tell me whether it is possible to run multiple X1900XT video cards in the Mac Pro? I understand that there's only one double-wide slot, so mechanically, plugging in a second X1900XT would obstruct an additional PCIe slot. The question is whether OSX will support more than one X1900XT.
    Thanx - Andy

    You can put X1900XT video cards in slots 1 and 2. The second board will cover slot 3, but there is enough power to run a 7300 in slot 4. Set the bus to x8 x8 x1 x8.

  • Have imac osx 10.6.8  with 2 gb 667 mhz ddr2 sdram. Can I get more ram and a good video card to use CS6 Premiere Pro

    I'd like to upgrade with more ram and a proper video card to properly use Adobe Premiere Pro CS6.
    I have an imac version 10.6.8  Can I boost this mac.
    Hardware Overview:
      Model Name:          iMac
      Model Identifier:          iMac5,2
      Processor Name:          Intel Core 2 Duo
      Processor Speed:          1.83 GHz
      Number Of Processors:          1
      Total Number Of Cores:          2
      L2 Cache:          2 MB
      Memory:          2 GB
      Bus Speed:          667 MHz
      Boot ROM Version:          IM52.0090.B09
      SMC Version (system):          1.6f0
      Serial Number (system):          W86510LAWH5
      Hardware UUID:          00000000-0000-1000-8000-0017F2CA47EB

    Sorry, you have the maximum amount of RAM in your computer, as shown in the specs below. Also the video card can not be upgraded.
    Maximum Memory     2.0 GB
    Memory Slots     2 - 200-pin PC2-5300 (667MHz) DDR2 SO-DIMM

  • So im about to buy a mac pro, I just need help cause im not sure if it's worth paying more for instance, a hi-res screen compared to the stock screen, and will i really miss the .2 ghz and the upgraded video card if I get the 2.0 ghz mbp?

    So im about to buy a mac pro, I just need help cause im not sure if it's worth paying more for instance, a hi-res screen compared to the stock screen, and will i really miss the .2 ghz and the upgraded video card if I get the 2.0 ghz mbp?

    The_Tiger92 wrote:
    So im about to buy a mac pro, I just need help cause im not sure if it's worth paying more for instance, a hi-res screen compared to the stock screen, and will i really miss the .2 ghz and the upgraded video card if I get the 2.0 ghz mbp?
    It appears the 15" 2.2 ghz isn't worth spending $400 more for, but you get the 1GB Radeon 6750M that has four times the VRAM than the 15" 2.0Ghz model and about 167% more performance. High settings on all current games with over 50 fps.
    If your not into 3D gaming or just light weight, then the 2.0 Ghz (last years performance) will suffice on low-medium settings at about 30 fps.
    The 13" is rather poor as it has integrated graphics. 30 fps on only some games.
    The high res screen is a excellent choice and the anti-glare is great for viewing just about anywhere.
    No messy films to replace at $30-$40 a pop.
    A lot of people bring the glossy screens back once they hear about the anti-glare.
    http://www.pcpro.co.uk/blogs/2011/05/23/glossy-vs-matte-screens-why-the-pc-indus trys-out-of-touch/
    Here's my 17"
    In my opinion the extra $400 for another 2-3 years of use out of the computer is worth it.
    Quad cores are more than enough for most uses for most people for many years, it's just a slow card is going to make the machine feel slow in rendering graphics in the future.

  • Interval selection and multiple single values in WAD Graphs

    Hi ,
    I am developing a Web Application Designer Graph  by combining multiple reports. I have 0CALMONTH,Country as my variable selections. By default I am able to select only single values (January,Feb etc.) But I need to select intervals(From-To) for 0CALMONTH and Multiple Single values for 0COUNTRY .
    I found the below link to use intervals by generating javascript
    http://help.sap.com/saphelp_nw2004s/helpdata/en/43/f5daaddfdb4c60e10000000a155369/frameset.htm
    But the issue here is, I am not able to change 'From' value i.e. according to this document , Interval start  is to be fixed in the script and I cannot change it later .But I want to change the interval start  any time later. I am not sure how to achieve this using this option.  Also I want to use mulitple single values variable for Country .
    Kindly let me know if there is any other possible options or work-around available.
    Thanks for your time.
    Thanks & Regards,
    Raja.

    Hi Janine,
            Thanks for your reply.I am using 7.0 Templates.Sorry to miss that part.  I think I need to explain the issue little more . I am developing a Chart  using Web Application Designer.  My Chart should be having the Variable in the top of the page and I can able to see that variable . Even I am able to change the values after the execution. But this is working fine only for the Single values, for ex. I can change the selection from June to July in the Chart and I am getting the correct result in my chart based on the selection .
          But the issue is ,I need to select Intervals for the month .Even though I created another variable with the option 'Interval' in the Query Designer , it is not showing the interval screen (From..To) ,instead still it is showing the single values option. I am using two different variables for these purposes and everything is correct with the query designer query. I am able to see the variable in the template,but I am not able to choose the interval values (only the intervals ,single value is ok)
    Thanks for your response
    Thanks & Regards,
    Raja

  • What is the difference between mxm30 viper and hd5570 1gb video cards

    What is the difference between mxm30 viper 1gb and hd5570 1gb  video cards in the Touchsmart 610 quad

    Hi renegade3,
    Same answer as last . . .
    Interface: MXM 3.0A
    Maximum resolution:HDMI resolution: up to 1080p
    1 GB onboard memory

  • Help! data manipulation for high speed streaming to disk from multiple boards and multiple channels

    I am using Labview 7.1 and have been trying to capture data from 12 channels simutaneously sampled at 2MS/s each and streaming to disk for up to a minute or more.  The hardware I am using is 2 x PXI 6133 S series boards with a MXI4 link to a Pentium D 2.8 Ghz machine with 2Gb ram.   I have 2 sata drives set up in a raid 0 configuration which should give me hard disk write speed faster or equal to the MXI-4 transfer speed. 
    I have first started off by using the example code "multi device sync - analog input- cont acquisition" which has enabled me to sync the two boards and sample at the required speed. 
    To stream the data to disk, I have first merged the data from each board  together to save it to one file.  I have tried using the storage vi's but I end up with a Daqmx read error (trying to read data that is no longer available).  I have played around with the read data size to the point that I either get a insufficient memory error, or I get the "trying to read data that is no longer available"  error.  I have also tried using the file IO blocks with some success and have found that I have been able to stream to disk only if I configure the daqmx read block to output the data in "raw 1D I16" format and plugging it into the file-write block.  In doing this, I have noticed that using  multiple channels on one daqmx read task, I will get all the channels in one 1D array rather than a 2D array organized by channels.  This makes it messy to read at the end of this, and I also don't want to write another vi to separate the channels, due to the high chance of getting the data mixed or messed up if I happen to change the number of channels on a board
    Is there a cleaner way of streaming this data to disk and keeping the channel data separated from each other?, and/or is there a better way to capture and handle the data I need? 
    I have attached the vi which I have got to consistantly work streaming to disk using the raw 1D I16 format.
    Thanks in advance to anyone who can help.
    Attachments:
    multidevicesync_analoginput_streamtodisk.vi ‏197 KB

    Hi,
    i can suggest following
    Refer to an example VI called as "High speed data logger.VI"  in conjunction with "High Speed data logger reader.vi" in Labview examples. Alhrough the logger might be in Tradiditional Daq format, it can be quite easily converted to Daq Mx format to store data in Binary (I32 format) . I have used this for many of my applications and i have found that the data retrieved does not have any "messups".
    Why not keep a seperate file for each card? This way, you do not have to load your application with extra process. You only have to acquire and save. After saving in Binbary format, you can retrive it offline, convert it to ascii format and merge the data files of various cards to get one consolidated ascii data file.
    hope this helps
    Regards
    Dev

  • Mac Pro Locked Up and Now  One Video Card and Audio Not Working

    Last night, my Mac Pro totally locked up to the point I had to power it off to get it to do anything. When restarted, one of my video cards and my audio are no longer working. I have dual monitors so tried switching the connections to see if it was the monitor and that was not the problem.
    I tried doing a formal shutdown after the restart and this also did not clear up my problem.
    Everything was working fine prior to the lockup. Any suggestions would be much appreciated.

    If you've added RAM and are using the nVidia 9400m video driver, you may be using incompatible RAM
    http://www.nvidia.com/docs/IO/60555/MemoryCompatibility_List_DA-04576-001v01.pdf
    My wife's MB is locking up when watching videos; hulu, iTunes, VLC. The above is the only answer I've found.
    BOL

  • LIVE Video Tutorial! How to Replace and Configure a Video Card - HP Expert Day "How-To" Video Series – Today at 1:00pm PST

    Join us at 1:00pm Pacific time for a LIVE video tutorial of how to replace a video card and configure video settings! The video features HP experts who work with the products every day!
    I am an HP employee.

    #test

  • I cannot open any photo in Photoshop CC 2014 after upgrade the application and drivers of video-card.

    Since I have made an upgrade of Photoshop CC 2014 I got a lot of problems.
    At first, I could not open any pictures in Photoshop. It works only if I disable "Use Graphic processor". I installed a new driver for my video-card, but it did not help. I use AMD FirePro V4800 for 10-bit colour.
    I had to return the system to the restore point (before the upgrade), then it worked somehow, but not stable. ACR from time to time had a blue screen with a white cross.
    Now I tried to install drivers for my video-card again, but it resulted in the same issue: Photoshop cannot open any photo. (Other converters and editors and also a new Lightroom work well).
    I use Win7x64, i7 2600, 16 Gb RAM, two SSD's, AMD FirePro V4800. I have never had any problems before the upgrade. And I do not want to reinstall Photoshop because I would have to reinstall a lot of plug-ins, I have already lost a whole day.

    Glad it's not just me!
    Interestingly, when I spoke with Apple, I tried it in a new user account and the problem went away. Apple said to speak to Adobe which I have done and after deleting settings/prefs again the problem remained. Adobe say as it's fine in a new account then it's an Apple issue not Adobe.
    I did find a workaround for now though, when using file - open, set it to list view instead of column view - this fixed my problem but sadly I'm used to working in column view so it's not ideal!
    I also got the same error message when trying to replace a set of brushes yesterday too. I need to go back to Apple now but just need to schedule some time to sit and troubleshoot!

  • Adobe CS4 OpenGL issues with 10.6.2 and Intel GMA950 video card

    I just upgraded to Adobe CS4 and in PS I cannot enable OpenGL. I'm running 10.6.2 on a Macbook with the Intel GMA950 video card.
    I was wondering if 10.6.2 does not have the relevant drivers for CS4 to recognize this chipset or that since the video card is integrated (as opposed to a stand alone with the newer Macbooks) that Intel has not update the drivers? It ***** since I cannot use some functions inside PS without OpenGL.

    Hello blue20 & welcome to discussions
    1.) You can search these forums for the topic of:
    Adobe CS4 GMA950
    As an example, if you haven't already, in an effort to parse what's already been discussed.
    2.) Have you looked at any of the Adobe forums:
    http://forums.adobe.com/message/2356530
    3.) How many fonts are you working with?
    The general approach at this time is to ask if you've checked for any problematic fonts (all languages) with Apple's Font Book (look in the Applications folder). Find and remove all duplicates also.
    Start there to be sure all fonts that are in play come out with a clean bill of health.
    Don't hesisate to perform wholesale deletion of old and/or little used fonts - be skeptical of anything that has come from Office 2008, including those related to an Equation Editor installation.
    By all means be sure any 3rd party apps AND plug-ins are Snow Leopard compatible.
    An additional measure is to clear the existing font caches:
    http://www.macworld.com/article/139383/2009/03/fontcacheclear.html
    That said, 10.6.2 release notes have this to say about fonts:
    http://support.apple.com/kb/HT3874
    Fonts fixes provided for:
    • an issue with font spacing
    • an issue in which some Fonts are missing
    • font duplication issues
    • an issue with some PostScript Type 1 fonts not working properly
    Good luck in any case.

  • Selecting from multiple installed video cards

    I have a ATI video card in slot 1 and the factory card in slot 3. My machine is a G5 Quad powerpc. Is there a way to tell specific applications which card to use? For example, I am running iTunes and want to use slot 1 card and have Motion use slot 3 card?

    Yes I just used HP to install the drivers. It worked unlike the AMD website, but it still doesn't seem to be working. It has all the updates now, but games stil don't seem to recognize the Radeon card, just the Intel HD video card.

  • Satellite L650-1M6 and problem with video card

    Good evening!
    I have new Satellite L650-1M6 with no OS. When i made a fresh Windows 7 32bit installation i got several device problems. Most of them i manage to resolve my self (like wlan drivers) but now i need your professional help.
    At this moment i had left this Problem Devices (from System information):
    Not Available ACPI\TOS6205\4&4A257CF&0 The drivers for this device are not installed.
    I think it could be video card (need to be ATI HD5470) but SysInfo say:
    Adapter Type Not Available, (Standard display types) compatible
    Adapter Description Standard VGA Graphics Adapter
    Would appreciate any help on this.
    Thank you in advance.

    Hello
    As I can see you got notebook without operating system and you try to install and configure your own OS.
    In many postings I wrote here I write again and again that most important thing is to install all drives and Toshiba specific stuff following right installation order so here is installation order for your notebook model:
    Win7
    TOSHIBA Assist 3.00.10_O
    TOSHIBA Extended Tiles for Windows Mobility Center V1.01
    Synaptics Touch Pad Driver 15.0.8.1
    Realtek Card Reader 6.1.7600.30111
    TOSHIBA HW Setup Utility v2.0.0.6
    TOSHIBA Supervisor Password Utility v2.0.0.3
    TOSHIBA Web Camera Application V1.1.1.15
    TOSHIBA HDD_SSD Alert 3.1.64.6
    Intel Chipset SW Installation Utility 9.1.1.1024
    Intel Management Engine Interface 6.0.30.1203
    Display Driver
    Intel Turbo Boost Technology Driver 1.1.1.1007
    Intel Rapid Storage Technology Driver 9.5.7.1002
    Conexant Audio Driver 4.119.0.61
    TOSHIBA Value Added Package 1.3.3_64
    LAN Driver
    TOSHIBA Software Modem 2.2.97(SM2297ALS05)
    Conexant Modem Driver 7.80.4.50
    Bluetooth Stack for Windows by Toshiba v7.10.10(T)
    Wireless LAN Driver
    ConfigFree 8.0.29
    I recommend you to install Win7 again and continue with all other stuff flowing this install order and I hope everything will be OK.

  • 694T Pro and Asus v8200 video card

    I can't seem to make my MSI 694T Pro run at AGP 4x mode with my Asus v8200 (a GeForce3 video card). It's running at 2x only with this card, but with GeForce2 cards it runs at 4x. I tried different versions of nVIDIA drivers and updating the BIOS to no avail.
    Any ideas?

    Okay, this is starting to suck, my new Mac Pro is acting up too. I have posted about crashing to another thread where NVChannel has problems and the screen freezes. And now I have this problem too. It's hard to get any new windows to appear (such as context lists, menu views or just normal application windows).
    And my log is full of this:
    28.2.2008 21:43:48 Dock[356] CGSResolveShmemReference : reference offset (65376) exceeds bounds (32768) on shmem obj 0x4a6e
    28.2.2008 21:43:48 Safari[532] CGSResolveShmemReference : reference offset (65296) exceeds bounds (32768) on shmem obj 0x4f1d
    28.2.2008 21:43:48 Safari[532] Error (1000) creating CGSWindow
    28.2.2008 21:43:48 Dock[356] CGSResolveShmemReference : reference offset (65296) exceeds bounds (32768) on shmem obj 0x5879
    28.2.2008 21:43:49 Safari[532] CGSResolveShmemReference : reference offset (65232) exceeds bounds (32768) on shmem obj 0x641a
    28.2.2008 21:43:49 Safari[532] Error (1000) creating CGSWindow
    28.2.2008 21:43:51 Safari[532] CGSResolveShmemReference : reference offset (65232) exceeds bounds (32768) on shmem obj 0x641a
    28.2.2008 21:43:51 Safari[532] Error (1000) creating CGSWindow
    28.2.2008 21:43:48 [0x0-0x8008].com.apple.dock[356] Thu Feb 28 21:43:48 myhost.com Dock[356] <Warning>: CGSResolveShmemReference : reference offset (65376) exceeds bounds (32768) on shmem obj 0x4a6e
    28.2.2008 21:43:48 [0x0-0x21021].com.apple.Safari[532] Thu Feb 28 21:43:48 myhost.com Safari[532] <Warning>: CGSResolveShmemReference : reference offset (65296) exceeds bounds (32768) on shmem obj 0x4f1d
    28.2.2008 21:43:48 [0x0-0x8008].com.apple.dock[356] Thu Feb 28 21:43:48 myhost.com Dock[356] <Warning>: CGSResolveShmemReference : reference offset (65296) exceeds bounds (32768) on shmem obj 0x5879
    Here is a screenshot some of the graphical mess I have now: http://img3.freeimagehosting.net/uploads/32f69aaf83.png

  • MSI Hetis G41 and double decker video cards

    Hi everybody, I'm interested in buying an MSI Hetis G41 as a starting point for my new small form factor computer:
     http://www.newegg.ca/Product/Product.aspx?Item=N82E16856167040&cm_re=hetis-_-56-167-040-_-Product
     But I have no idea it can properly hold a double decker video card, since there are no pictures of the inside anywhere and reviews of the Hetis don't really exist. Specifically, can it fit the Sapphire 5750:
    http://www.newegg.ca/Product/Product.aspx?Item=N82E16814102859&cm_re=sapphire_5750-_-14-102-859-_-Product
     Thanks for any help you can give.

    From the Newegg link:
    Quote
    This tiny system measures only 3.7” x 12.6” x 12.99”
    I don't see any way that card could fit.
    Besides, you miss the point of these 'ultra-small form factor' units, they are designed as low-consumption, simple desktop PCs. Not everyone wants to play games on a PC, some people just like to browse the net, send/receive emails, watch/listen to videos/music, and type letters. Thats the market these units are aimed at.
    If you want a machine you can put a 5700-series (or other equivalent) graphics card for gaming, then MSI's small-form factor systems are not for you.

Maybe you are looking for