Z97g43 connect front panel audio to computer case

I have z97g43.
Front panel audio computer case to mainboard not work.
i have connect:
JAUD1
mainboard chassis ( all pin available connected )
mic_L mic_L
mic_r mic_power
headphone_r headphone_r
headphone_L headphone_L
ground ground
not connect:
Sense send
mic detenction
headphone detenction
what is the right schematic connect?
thanks

What case do you have? If it is an older case with AC97 audio then you would need to purchase something like one of these: http://www.amazon.com/s/?ie=UTF8&keywords=hd+audio+front+panel&tag=googhydr-20&index=electronics&hvadid=54539991636&hvpos=1t2&hvexid=&hvnetw=g&hvrand=11069445173547096755&hvpone=&hvptwo=&hvqmt=b&hvdev=c&ref=pd_sl_2w99a9udvo_b
I simply got me an inexpensive case for my last upgrade since I also needed front panel USB 3 and up to date card reader in addition to the HD audio. My case was only $10 more (free shipping at time of purchase ) than the front panel module I needed so I got the new case you see in my signature instead.

Similar Messages

Connecting Front Panel Audio to K8NGM2

I am trying to connect the front panel Audio(Headphone Jack and Mic) I front panel wires are labeled R-In, R-Out, L-In, L-Out, Mic Bias and Mic and GND.The MBconnectors are labeled port 1L, GND, Port 1R, Presence #, Port 2R, Sense1_Return, Sense_Send, Key, Port 2L, Sense2_Return.
Can this be done?

I quess you guys got a AC97 configuration wire and have HD audio on board.
I bough a new case some days ago and that one had a HD audio and a AC97 wire.
you guys just cant connect it without the right wire.
You can try to manualy put it in the right configuration because HD and AC97 use the same wires but other sequence.
but I quess you cant pull them out of the jack so maybe you need to get a emty one and cut the wires off and put them in the right holes or something
or just buy a new case

Connecting Front Panel Audio(in Lian-Li PC Ca

I can't seem to find any decent documentation, what i need to do is connect the front panel audio rack that's at the bottom of my case to my audigy 2 ZS(just the regular one, not gamer or any of those). The only two things that need to be connected are the headphone jack and the mic jack. I need to know where i pluge them in though.

I quess you guys got a AC97 configuration wire and have HD audio on board.
I bough a new case some days ago and that one had a HD audio and a AC97 wire.
you guys just cant connect it without the right wire.
You can try to manualy put it in the right configuration because HD and AC97 use the same wires but other sequence.
but I quess you cant pull them out of the jack so maybe you need to get a emty one and cut the wires off and put them in the right holes or something
or just buy a new case

Connecting front panel audio(case) to x-fi xtreme mu

Hi,
Im trying to connect the front panel mic and headphone jacks on my antec sonata 2 case to my x-fi xtreme music s card,here is what i have/havent found out:?.after 2 hours of trying ,then 35 seconds of looking here,i tried to stick the mics jack into the wired remote mic jack of my t7900 speakers thinking it would work,can someone pls clarify that input on wired remote is ONLY for mp3 players etc,and not for microphones?2.there appears to be a way of connecting the single pins coming from my front audio panel on case(there is also a 0 pin block ,but that doesent fit,i think it for intel something or other) to the long 0 strip pin thing on the x-fi card,i have see various diagrams on the net etc,but some different,most labelled -0 but i dont know which one is and one is 0 etc....again,if any? one can explain how i could do this pls?3.is it just easier to buy the x-fi 5.25inch front panel jobbie,if the above is not possible?,and if so i have problems sourcing that too anywhere in uk?srry for asking so many questions,but im a bit peeved to have all this gear,go out to buy a headset and mic for playing games,and find out its harder than the krypton factor to set up... many thanks in advance?sc_

Lazy to search? It's been here (and there) 'bout thousand times already so it shouldn't be hard to find...
?....actually no,i thought my post clearly stated that i had seen conflicting posts and diagrams with regards to which was the right way to conenct the headers to the pins,and i was just looking for clarification. I apologise if i wasent clear in enough in this. Anyway,thankyou for taking yor time to respond and i will look into the link you gave me and see if its a good solution. Incidenatlly,another thought occured to me this morning.As i have the t7900 wired remote sat on my desk its entirely possible to run a?3.5mm male/female jack extension from the mic input of my x-fi card and place it next to my wired remote,having the mic jack of headset in this extension,and the headphones jack in the wired remote input.....is this a viable solution,and would this not compromise quality?again ty for your time. sc_

How connect front panel audio on audigy sb0090 Platinu

Hello i have an audigy platinum Sb0090 but i don't have the rack creative optional... I would like to connect a front pannel audio from my Super Lanboy Antec. I can't find the schemas of the audigy platinum connectors.Could you help me ?

Djowoz wrote:
Hello i have an audigy platinum Sb0090 but i don't have the rack creative optional... I would like to connect a front pannel audio from my Super Lanboy Antec. I can't find the schemas of the audigy platinum connectors.Could you help me ?
Here is one place to start from - http://audigy2zshowto.blogspot.com/.
Follow the links found on that page to other sources --> you may find the pin-order for your card/case models too.
NOTE: Pin order on 0-pin properiatry connector may vary a bit from A2Zs what's been used there (like it did for Audigy 2) but it's not very difficult to find out the right pins.
jutapaMessage Edited by jutapa on 03-22-20062:57 PM

Problem Connecting Front Panel Audio to P965 Neo-F

Here is the layout of pins on motherboard:
Casing jumpers: (Casetek 1026-10)
Do you know how to connect this one? Thanks!

Try this:
PIN 1 - MIC IN
PIN 2 - GND
PIN 3 - MIC PWR
PIN 4 - No connector
PIN 5 - SPKOUT R
PIN 6 - REAR R
PIN 7 - Not used
PIN 8 - No connector
PIN 9 - SPKOUT L
PIN 10 - REAR L
Cheers

MSI P965 Platinum - Front Panel Audio u/s

Finally after managing to get XP Pro SP1 CD to install, I have a stable system, and thanks to those whom freely gave advice.
But we hit the next issue with this motherboard, the front panel audio.
Firstly the Realtek detection software doesn't detect anything plugged into the front panel.
Connected the cables as follows from my Coolermaster Stacker case;
mobo = case wires/colour
pin1 aud-mic = mic-in - yellow
pin2 aug-gnd = gnd - black
pin3 aud-mc-bas = mic-pwr - red
pin4 aud-vcc = empty
pin5 aud-fpout-R = R out - green
pin6 aud-ret-R = R ret - green
pin7 hp-on = empty
pin8 key
pin9 aud-fpout-L = L out - white
pin0 aud-ret-L = L ret - white
The above pin out gives nothing at all, but audio from rear ports on the computer motherboard is fine.
I also tried the following,
where the microphone wires were left disconnected, therefore just the speakers plugged into the front panel audio header
mobo = case wires/colour
pin1 aud-mic =
pin2 aug-gnd = gnd - black
pin3 aud-mc-bas =
pin4 aud-vcc = empty
pin5 aud-fpout-R = R out - green
pin6 aud-ret-R = R ret - green
pin7 hp-on = empty
pin8 key
pin9 aud-fpout-L = L out - white
pin0 aud-ret-L = L ret - white
The above still gave me no audio out from the front panel.
Intrestingly if I leave the front panel audio header blank, I still get rear audio fine, where I would have expected to have put jumpers across the L and R outputs as is the norm.
I have removed the front panel from the computer to ensure that the wires terminate OK, and have not been pulled out/off.
Have I plugged in the wires correctly?
Is there some hidden setting that I have missed, I admit that I do not like the Realtek audio software?
I cannot find any way to boost the microphone input since Realtek audio software has been installed.
One day case/mobo manufactures will use a standard for the front panel headers and front panel audio headers, and we will have a simple single plug to insert, rather than a group of single fiddly connectors that have to be attached to a header that was at the last minute attached to the motherboard as far away from the front of the case, and in the darkest most fiddle corner.
Oh well......
Cheers

AaronYuri - you're are so right there my friend. I just pity Joe User whom might attempt such a move themselves.
In the end my entire issue was software related, and that has to be blamed on Realteks software, far too many options approached from far too many different angles. Audio is really simple, plug your cables in, and it should just work, certainly in the simple case of 2-1 speakers and a microphone. Why exactly it took a couple of hours to figure out how to get the front panel microphone to be seen in the first place, let alone any signal, is beyond me.
So my cables were all connected correctly as per the MSI manual, confirmed by my Abit manual and other post here and on other forums.
In the Realtek MSI audio software, on the I/O Audio tab, connector settings, I had to select 'disable front panel jack detection' and 'mute rear panel output when front headphones plugged in'. The other option here 'enable auto pop up...' is unchecked.
After this the Realtek software mentioned something about a new profile had been set up?
I then went to Windows Control Panel, Sounds and Audio devices, and selected the voice tab, on this page I selected 'mic IN at front panel [pink]' from the drop down list for Voice Recording'. Proceeded to 'test hardware' and the microphone is now working. This option to select the input in the drop down list was not available before.
All a bit of POKE and HOPE.
But we seem to be there.

MSI K9N PLATINUM FRONT PANEL AUDIO

Hi everybody
I recently mounted an MSI K9N Platinum mainboard. When connecting front panel audio from case connectors on JAUD1, case connectors are marked as follows:
MIC POWER
MIC IN
GROUND
R-RET
L-RET
R-OUT
L-OUT
which does not match with those written on mainboard user manual for JAUD1 which are FRO PIN 1 TO 9 as follows:
PORT1L
GROUND
PORT 1R
PRESENCE
PORT 2R
SENSE1_RETURN
SENSE_SEND
KEY
PORT2L
SENSE2_RETURN
.I´ve tried to connect it on many combinations but yet it is not working.
Could someone tell me the right way to do it?
Thanks in advance.

I think you better ask this question to the manufacturer of the frontpanel stuff, as I have no clue.

K9N Neo Front Panel Audio

Hi all -
I have a K9N Neo (MS-7260 v2.0) that I am trying to wire in the front panel audio from my case. I'm having some major problems trying to figure out how to match up my case wires with those on the MSI board. I'm hoping that one of you experts will have the answer.
My case has the following signals for a microphone and headphone connection:
MIC GND
MIC PWR
MIC IN
HPOUT R
HPOUT -R
HPOUT L
HPOUT -L
HPOUT GND
In other words, the mic has power, ground, signal; and the headphone has two wires for each channel (+/-) and a common ground.
Now, here is the listed pinout from the manual for JAUD1. I could only find the manual for a PCB v1.0, so if that is the issue then please help me find the right manual:
PIN SIGNAL DESCRIPTION
1 PORT 1L : Analog Port 1 - Left channel
2 GND : Ground
3 PORT 1R : Analog Port 1 - Right channel
4 PRESENCE# : Active low signal - signals BIOS that a High Definition Audio dongle is connected to the analog header. PRESENCE# = 0 when a High Definition Audio dongle is connected.
5 PORT 2R : Analog Port 2 - Right channel
6 SENSE1_RETIRN : Jack detection return from front panel JACK1
7 SENSE_SEND : Jack detection sense line from the High Definition Audio CODEC jack detection resistor network
8 KEY : Connector Key
9 PORT 2L : Analog Port 2 - Left channel
10 SENSE2_RETIRN : Jack detection return from front panel JACK2
It doesn't seem like there are enough signals to hook up a +/- for both L/R on the headphones. And where do I put the mic??
Thanks in advance for ANY insights!
Dave

Hello!
I dare not answer your question yet, but I know that many with this kind of question have been helped by contacting the case manufacturer's support some way.
Sure it is not life or death for your problem, but Moderators here are under death penalty not to help people who don't describe their complete system. Motherboard we know. Processor, memory, hard disks, PSU and it's max. amperes and a few other things remain unknown.

P35 Platinum front panel audio with Antec P180 case?

God I have a headache after reading all those "front panel audio" threads. Why can't mb's all use the same freaking pinouts!!!!
The case doesn't have a HD front panel.
MB pinouts are:
1. Mic_L (MIC Left Channel)
2. GND
3. MIC_R (MIC Right Channel)
4. PRESENCE#
5. LINEout_R (analog port right channel)
6. MIC_JD (MIC jack detect)
7. Front_JD
8. NC (empty)
9. LINEout_L (analog port left channel)
10. LINEout_JD
Case Front Panel connector is a preconfigured block with pigtails hanging off in case it doesn't match up.
1. MIC Signal
2. MIC Power (MIC BIAS)
3. Ground
4. FPOUT-R (front right)
5. FPOUT-L (front left)
6. RET-R (rear right)
7. RET-R (rear left)
glaring differences are the ground and the MIC connectors.
How do I connect these? I don't want to fry anything.
Thanks.

They do have the same pinouts. There are two standards is the reason for two different pinouts. It's just that your MB is Intel HD and your case is AC-97.
For Intel® High Definition Front Panel Audio
Pin Signal Name Description
1 PORT 1L Analog Port 1 - left channel (Microphone)
2 GND Ground
3 PORT 1R Analog Port 1 - right channel (Microphone)
4 PRESENCE# Active low signal that signals BIOS that an Intel® HD Audio dongle is connected to the analog header. PRESENCE# = 0 when an Intel® HD Audio dongle is connected
5 PORT 2R Analog Port 2 - right channel (Headphone)
6 SENSE1_RETURN Jack detection return for front panel (JACK1)
7 SENSE_SEND Jack detection sense line from the Intel® HD Audio CODEC jack detection resistor network
8 KEY Connector key
9 PORT 2L Analog Port 2 - left channel (Headphone)
10 SENSE2_RETURN Jack detection return for front panel (JACK2)
For AC-97 Front Panel Audio
Pin Signal Name Description
1 MIC Front panel microphone input signal (biased when supporting stereo microphone)
2 AUD_GND Ground used by analog
3 MIC_BIAS Microphone power / additional MIC input for stereo microphone support
4 AUD_GND Ground used by analog audio circuits
5 FP_OUT_R Right channel audio signal to front panel (headphone drive capable)
6 FP_RETURN_R Right channel audio signal return from front panel (when headphones unplugged)
7 AUD_5V Filtered +5 V used by analog audio circuits
8 KEY No pin
9 FP_OUT_L Left channel audio signal to front panel (headphone drive capable)
10 FP_RETURN_L Left channel audio signal return from front panel (when headphones unplugged)

K8NGM2-FID - connecting of front panel audio (AC'97)

Hello,
I have a K8NGM2-FID based pc running XP Prof. I have a Chieftec LCX-01B-B-SL case with front panel audio. This panel is compatible with AC'97 standard. PIN Assigment of the internal Frontpanel connectors for Audio is below described:
I red in manual of my mobo:
"The JAUD1 front panel audio connector allows you to connect to the front panel audio and is compliant with Intel® Front Panel I/O Connectivity Design Guide."
I red Front Panel I/O Connectivity Design Guide (downloaded from intel site) and:
"2.3.3 Audio Design Considerations
Front panel audio design in conjunction with motherboard audio header design is dependant upon the type of audio CODEC being used on the motherboard. In the past, AC97 Integrated Audio CODECs were prevalent. With the introduction of Intel High Definition Audio, many new motherboard designs are switching over to High Definition (HD) audio CODECs. Designersshould note that AC’97 and Intel High Definition Audio front panel motherboards and I/O cardsimplementations are different and may not be directly compatible or interchangeable
CAUTION
It is strongly recommended that motherboard designers only use Intel® HD Audio analog front panel dongles with the Intel® HD Audio analog front panel header to insure that the jack detection and dynamic re-tasking capability is preserved. Passive AC’97 analog front panel dongles (ones which leave the 5V Analog pin-7 line unconnected on the dongle) may be used with the Intel® HD Audio analog front panel header. But note that the front panel jack detection and re-tasking functionality will be lost as the AC’97 jacks cannot support connection to the SENSE line. In addition, software must be aware that an AC’97 dongle is being used with an Intel® HD Audio analog header since the software might need to dedicate codec ports that are connected to the header to meet the product’s intended functionality.
2.3.4.4 AC’97 Header Pin Jumpers
The rear panel audio output jacks are disabled when headphones are plugged in. If the front panel interface board is not connected to the front panel audio header, jumpers should be installed across header pin pairs 1-2, 3-4, 5-6, and 9-10. If these jumpers are not installed, the rear panel line out connector will be inoperative and microphone input pins 1 and 3 will be left floating, which could lead to elevated back panel microphone noise and cross talk.
NOTE
Motherboards that have the foot print for a front panel header, but depopulate the front panel audio header must have 0 ohm resistors as options to connect the FP_OUT and FP_RETURN signals. These resistors must be installed when the header is depopulated to insure audio is routed
to the back panel."
Can I connect this front panel audio to front Panel Audio Connector (JAUD1) of K8NGM2-FID (Realtek High Definition Audio)? Will it be work correctly?

No I don't think it will, I had the same problem with my Coolermaster Centurion case, the pin out configs are different. I just left it disconnected, and didn't worry about it

Connecting the chassis-mounted front panel audio I/O module to the X-Fi Extreme Mu

Hello to everybody.
Many pc chassis provide two audio connectors on the front side, usually for the headphones with microphone.
I need to know if I can connect the chassis-mounted front panel audio I/O module to the Sound Blaster X-Fi Extreme Music.
I saw that the X-Fi Extreme Music has the internal connector (named AD_EXT) to connect . Is there a pin mapping of the AD_EXT connector? Is it possible to connect the chassis-mounted front panel I/O module cable to the proper pin of the AD_EXT connector?
Thank you.

Hi and thank you for your response.
Unfortunatelly I actually haven't got a X-Fi card, because I need to know if I can connect the chassis-mounted front panel audio I/O module to the card before buying it.
For this reason I don't know what is the J you're talking about. Is it an internal connector avaiable in the X-Fi Extreme Music card? Can I use this J to connect the chassis-mounted front panel audio I/O module to the card?
Thank you.

Fronta panel audio connections on KM4M

I got a pc case, and the cables for the front panel audio are: left , right , mic, and ground. The front panel works fine, but the rear ports dont.
What should i do to make it work?
Maybe conect left in with left out and right in with right out?

There must be a return from fron panel audio for rear ports to work
What i did was to solder a piece of solid wire on the jumper, and simply plug in the front panel audio left and right in that wire and it works FINE
to Wonkanoby: u know fak all dont u?

Front panel audio jack is not working on K9N Neo V2

My front panel audio jack is not working on K9N Neo V2. I check the JAUD1 cable and it appears to be connected to the front panel audio jack. My soundcard driver cannot detect any gadgets when I plug it in the front panel. My audio drivers and BIOS are up to date. Is there any known solution to this? My computer is only a few months old and I have not tried the front audio jack until recently. I'm on Vista home premium btw.
Also, I've got another problem, my processor is AMD 64x2 4400+ overclocked to 2.63Ghz. I've been using that clock value ever since I built this computer and stress tested the processor and found that it would not cause any problems like hanging or overheating. However, I recently decided the need for AMD's Cool & Quiet technology and enabled it. It caused BSODs every few days or per week that didn't happen before. I tried it with the default clock value and it still causes BSODs. Can someone help me?

Quote
Thanks. Its ironic that disabling it actually enables it.
It has to day with the front panel audio wiring of your case. How many wires are there that can be connected to the board's pin header?
Quote
Sound quality isn't very good
Can you be more descriptive? Is the quality better if you plug the headphone into one of the jack at the back panel? (Also, make sure you tell the Realtek HD Audio Manager, that a headphone is connected (and not regular speakers).

MSI K9A2-CF front panel audio problem

Just rebuilt a computer using the board. Please note, I have not updated the BIOS at all and I am using XP Pro. Anywho, I've tried everything under the sun, so far, aside from previously stated, to get this sucker to work. I have it connected properly, I've installed every audio driver on the motherboard CD. I can't find a setting in the BIOS to turn on front panel audio either. Everything else works fine though. USB's, HD audio connections in the back, etc. The program in windows will detect all inputs except for the front audio in and out.
I'm a bit stumped. Any suggestions?

Quote from: Bas on 17-August-09, 22:22:14
You have to check the wires on the plug, looks like they are wrong or the case-module is broken somewhere.
You have to start checking and measuring with an Ohm-meter.
Remember, neither case front worked. I'm not saying it couldn't be the case, but I'll try to get my hands on an Ohm-meter. Where can I find out what values I'm looking for? I know next to nothing about testing to that extent.
Also, what if it's the motherboard itself? Isn't there somewhere in the bios and/or windows device manager that I can confirm whether or not the device itself is working, or not working, properly?
Thanks for your replies so far.
Mike,
I honestly don't know, but the case only has one audio cable, and the MB only has one audio plug-in for the front panel. I have both drivers installed. The on-board audio plug-in on the rear of the computer works fine. I can get sound, etc, no problem from the rear. Front panel only is not working.

Z97g43 connect front panel audio to computer case

Similar Messages

Maybe you are looking for