ZCM 11 very slow Windows 7 image restore

Hello NG
In our enviroment we work with ZCM11. We made a Windows 7 image. The zcm
filesize is about 4.7 GB. The disksize is 40 GB.
Now the restore take long time. For restoring 4.7 GB Zenworks Imaging need
about 85 Minutes. It can not be true!!
The cause why ZCM imaging has problems is the winsxs folder, with a lot of
small files. Here ZCM do lose much time.
Does exist a patch or hotpatch that do solve this issue?
Regards
Ramon

Hi Domicicm
could you send me a link where i can download this imagex tool? I didn't
find a third party software for imaging.
Ramon
"dominicm" schrieb im Newsbeitrag
news:[email protected]..
hi ramon, if you read older posts on this concern, yes it is "normal"
.... it seems that's the limitation of the actual imaging engine (10.3
or 11).
I'm in the same boat as you, Novell recommends to use imagex the
third-party tool, that works really fast (about 12 min to restore an
win7 image, even with the winsxs folder) but the problem with imagex is
we can't multicast, so big problem here..... no real solution, and
Novell is expecting to release a new Imaging Engine for about the
spring....
dominicm
dominicm's Profile: http://forums.novell.com/member.php?userid=4271
View this thread: http://forums.novell.com/showthread.php?t=432403

Similar Messages

Very slow Windows domain login over IPSec VPN

Hi
I'm experiencing very slow Windows domain logins over an IPSec VPN connection. The AD is in Site 1, some users are in Site 2. Two Cisco ASA firewalls connect both sites by an IPSec VPN over the Internet.
I made some registery changes on the Windows XP client on site2 to let Kerberos communicate over TCP instead of UDP. Still the logins take extremely long (45 minutes). Profiles are very small, so there had to be a problem with Kerberos, MTU sizes or somethin like that. I already changed the clients MTU settings to 1000 byes, but login is still very slow. I made some sniffer logs...
Does anybody know what the problem can be ?
Regards
Remco

Hi Remco,
The most common issue with slowness over VPN is going to be fragementation. In general below are the recommendations to avoid fragmentation
1. For TCP traffic, use "ip tcp adjust-mss 1360" on the Internal LAN Interface on the Router. If you are using GRE then configure "ip mtu 1400" under the Tunnel Interface.
If you are not using GRE then the value of "ip tcp adjust-mss" depends on the type of transform-set being used E.g. AES\3DES etc, so you can increase the value of TCP adjust command from 1360 to a higher value. Though I will start from 1360 first for testing.
Also take a look at the below article for MTU Issues
http://www.cisco.com/en/US/customer/tech/tk827/tk369/technologies_white_paper09186a00800d6979.shtml
Thanks,
Naman

After Photoshop CC 2014 update - Photoshop is very slow (Windows 7)

After updating today to the latest photoshop cc2014 Version, Photoshop starts very slow and is not useable.
I updated from V. 2014.1.0 to 2014.2.1 20141014.r.257.
Starting Photoshop Needs 6 minutes (before 1.5 minutes). The menue and button reactiontime is more than slow, you cant work with this Setup.
Is there a Problem with the new release?
And please Adobe, dont tell me, my System has a problem. Did only an update on the CC2014 Suite via creative cloud. Old PS Version (2014.1.0)runs great.
After testing a few time, I recovered my System back to Version 2014.1.0 with Windows recovery and Photoshop works good again.
So whats wrong with the new release?
My PC config:
Adobe Photoshop Version: 2014.2.1 20141014.r.257 2014/10/14:23:59:59 CL 987299 x64
Windows 7 64-Bit
Version: 6.1 Service Pack 1
Intel CPU-Familie:6, Modell:10, Stepping:5mit MMX, SSE (ganze Zahl), SSE FP, SSE2, SSE3, SSE4.1, SSE4.2, Hyper-Threading
Physischer Prozessor: 8
Logischer Prozessor: 16
Prozessor-Taktfrequenz: 2664 MHz
Memory: 20463 MB
Thanks for any tipp!
BR.
Werner

The CC 2014 update 2014.2.1 is a month old and ACR 8.7 is two days old. Something strange is happening to you. First try resetting your Photoshop Preferences. This is a Adobe Photoshop User forum your not dealing with Adobe here. You seem to think you are and your attitude seems like you not open to to possibility that your system may have a problem. I think you may have one..
Adobe CC 2014 Product Updates/Downloads for Windows
Photoshop CC 2014
File Download
Size
Date
Notes
Adobe Photoshop 2014.2.1 Update for CC 2014 (64-bit)
249 MB
10/20/2014
Release 15.2.1
Adobe Photoshop 2014.2.1 Update for CC 2014 (32-bit)
223 MB
10/20/2014
Adobe Photoshop 2014.2.0 Update for CC 2014 (64-bit)
249 MB
10/6/2014
Release 15.2
Adobe Photoshop 2014.2.0 Update for CC 2014 (32-bit)
223 MB
10/6/2014
Adobe Photoshop 2014.1.0 Update for CC 2014 (64-bit)
236 MB
8/5/2014
Release 15.1
Adobe Photoshop 2014.1.0 Update for CC 2014 (32-bit)
210 MB
8/5/2014
Adobe Camera Raw – ACR
Adobe Camera Raw 8.7 Update for CC
122 MB
11/18/2014
Release 8.7
Adobe Camera Raw 8.6 Update for CC
106 MB
7/28/2014
Release 8.6
Adobe Camera Raw 8.5 Update for CC
100 MB
6/18/2014
Release 8.5

Photoshop CS6 very very slow (Windows 7)

Hi, im desperate as ive run out of options i think. Photoshop CS6 behaves slow, very slow.
Even with no document open, right after launch it reacts with delay on any mouseclick, sometimes it takes
more than 20 seconds before a menu pops open after clicking. Painting paintbrushes are impossible slow.
Basically any action is dragged.
Its impossible to work like this. With all previous versions of PS i never encountered this.
Things i tried :
- turned off gpu acceleration (i read that gpu can cause performance issues, some ppl solved slowness by turning it off)
- updated latest nvidia drivers
- reinstalled photoshop
- tried to inspect photoshop processes with ProcessHacker, even when at 5% cpu it runs extremely slow
specs :
Windows 7
Nvidia GT545
1 terrabyte free scratch disk space (on C:)
8 gb ram
CPU i7 2600

Has it always run slow, or did this start recently?
What anti-virus are you using? Have you tried disabling it to see it that make a difference?
Are you working over a network?

Very Slow Windows Networking

My department is running OS X 10.4, and we're networked with a Windows server for storage and job backup. One of our main backup servers is very slow. Logging into the server can take up to 5-7 minutes, and for a period of 5-7 minutes after that the machine logging into the server will run very slow, even when not copying a file.
Now the backup server is quite large (almost a terrabyte), which is my belief why it runs so slowly. We have two other servers on the same network that behave fine.
Is there something on my end (OS X) that can speed up the problem, or is this a server issue? My boss is demanding answers and our Windows IT guy is placing the blame solely on our Macs (with no evidence of course). Help!

Google for "SMB performance". There are a bunch of discussions on macosxhints on how to tweak SMB performance on Max OS X. I have tried a few different ones, which all seem to help in some small way. YMMV.
Apple SMB is not known for its performance.

Sattalite Pro 6100: Very slow Windows installation

I have a Sattalite Pro 6100 series.
The harddrive crashed, so I bought a new one. It is 40 GB / 5700 RPM, so supposedly slightly faster than original equipment.
When I placed it, BIOS did not see it.
I removed it, put it back and BIOS did see it.
I placed the Dutch Windows XP Home CD and NTFS formatted (not fast) the entire HD.
After that Windows took a good 3 hours to install even though it claimed it would only take 39 minutes to start with.
Booting up to Windows takes a long time.
Windows operation seems slower than what I am used to, but I have not actually used the (crashed) laptop for 2 months, so I can't be sure.
Any idea's?
David

Well, yeah. I kinda figured it would be hard to answer, but maybe, just maybe it was a known issue?
HDD manufacturer is Toshiba.
I have downloaded the BIOS update and will install this later today. Will this fix the installation of Windows, or is everything just slow due to lack of BIOS update and it will fix itself. In other words: do I need to re-install Windows because it took forever to install?
No image recovery possible. The old HD is DEAD! No image was made before it died.
David

Time Machine is very slow after I restored my Mac from a backup

My computer went in for repair because of a damaged logic board. Upon it's return the hard drive was blank so I restored all my data from a Time Machine back up. Everything seems to work fine except for Time Machine.
It is unbelievably slow. It takes an hour to back up 50 megabytes.
I have checked Activity Monitor and the process 'backupd' rapidly fluctuates between 20-100% CPU usage.
The behavior of Time Machine seems odd as well. Backing up small amounts of data minutes apart. e.g. It will back up 100mb, then a few minutes later back up another 100mb or so. I realize things run in the back ground but this goes on for hours and hours even if the computer is not being used. I have left the computer on overnight to find it still backing up the next morning.
Also, occassionally it will tell me that it is preparing 30,000+ files (which takes a good 10-15 mins whereas it used to take a few seconds) and only back up 10mb. This never happened before. Again I know, 30,000 small files *could* equate to 10mb but the bahvior just seems off to me.
I have been backing up my MBP plus 2 other computers to a Western Digital My Book II 4TB drive successfully (and quickly) for about 3 or 4 months. The other computers still back up quickly to the drive.
I have found solutions saying to quit Finder while backing up and add your back up drive to Spotlight's Privacy list etc. Nothing has worked for me and I would like to find a real solution.
Thanks in advance.

Ok, thanks.
The preferences file might be damaged; try a "full reset" of Time Machine, per #A4 in Time Machine - Troubleshooting.It's a long shot, but quick and easy.
Download and install the "combo" update, per Installing the ''combo'' update and/or Reinstalling OSX.
If that doesn't help, consider reinstalling OSX (that won't disturb anything else).

Very slow create, image is local

All
Installed the VM template for Oracle 10g, seemed successful (using Oracle VM Manager)
Trying to create VM from the template and its really slow. The create has been running for 1/2 hr so far
and the stats below are pretty constant over this period. CPU mostly waiting
This is a HP DL140G3 with dual 5150 and 7Gb ram.
Is this expected behaviour, previous experience with VMWare on the SAME box
was very different (MUCH faster at loading VMs)
2 drives, 147Gb 15K SAS
500Gb SATA
Filesystem Size Used Avail Use% Mounted on
/dev/sdb1 3.0G 738M 2.1G 27% /
/dev/sdb2 462G 150G 313G 33% /OVS
/dev/sda1 99M 36M 59M 38% /boot
tmpfs 324M 0 324M 0% /dev/shm
/dev/sda2 133G 192M 126G 1% /opt
top - 21:35:16 up 56 min, 1 user, load average: 1.95, 1.83, 1.65
Tasks: 106 total, 2 running, 102 sleeping, 0 stopped, 2 zombie
Cpu0 : 0.0%us, 0.7%sy, 0.0%ni, 0.0%id, 99.3%wa, 0.0%hi, 0.0%si, 0.0%st
Cpu1 : 2.0%us, 0.7%sy, 0.0%ni, 97.4%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st
Cpu2 : 0.7%us, 0.7%sy, 0.0%ni, 98.6%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st
Cpu3 : 0.0%us, 0.0%sy, 0.0%ni,100.0%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st
Mem: 662704k total, 658344k used, 4360k free, 968k buffers
Swap: 1052248k total, 108k used, 1052140k free, 514572k cached
PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND
6251 root 18 0 18312 8724 1544 D 1 1.3 0:11.66 python
3600 root 15 0 12376 5316 2156 D 0 0.8 0:05.19 python
9758 root 18 0 0 0 0 Z 0 0.0 0:00.01 python <defunct>
1 root 15 0 2044 628 540 S 0 0.1 0:00.32 init
2 root RT 0 0 0 0 S 0 0.0 0:00.04 migration/0
3 root 34 19 0 0 0 S 0 0.0 0:00.03 ksoftirqd/0

haven't tried the vm.cfg create yet
[root@oraclevmserver init.d]# ./iptables status
Table: filter
Chain INPUT (policy ACCEPT)
num target prot opt source destination
1 DROP tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:21
2 DROP tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:80
3 RH-Firewall-1-INPUT all -- 0.0.0.0/0 0.0.0.0/0
Chain FORWARD (policy ACCEPT)
num target prot opt source destination
Chain OUTPUT (policy ACCEPT)
num target prot opt source destination
Chain RH-Firewall-1-INPUT (1 references)
num target prot opt source destination
1 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0
2 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 255
3 ACCEPT esp -- 0.0.0.0/0 0.0.0.0/0
4 ACCEPT ah -- 0.0.0.0/0 0.0.0.0/0
5 ACCEPT udp -- 0.0.0.0/0 224.0.0.251 udp dpt:5353
6 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:631
7 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:631
8 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED
9 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:21
10 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22
11 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 state NEW udp dpt:53
12 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:53
13 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:80
14 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:2049
15 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpts:5900:5950
16 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:8002
17 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:8003
18 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:8899
19 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:7777
20 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited

PE7 very slow Windows 7 64 bit

Hi guys,
PE7 is running very slowly for me.
I'm running an i7 920 with 8GB of ram.
Windows 7 64 bit
Graphics card is Nvidia GeForce 9600GT running the latest driver V270.61
I am importing AVCHD videos into PE7 and then just dragging them across onto the work timeline and it just takes ages and hangs there for quite a while.
I can't edit the video on the timeline at all as it is just taking too long.
Any suggestions out there would be appreciated.
thanks

Since AVCHD is a video file, not just a static picture, hard drive configuration is important
My 3 hard drives are configured as... (WD = Western Digital)
1 - 320G WD Win7 64bit Pro and all program installs
2 - 320G WD Win7 swap file and video project files
3 - 1T WD all video files... read and write files
Trying to use only ONE Hard Drive for Video Editing
You are a music conductor, with a baton that you use to point to various parts of the orchestra... this is like Windows pointing to various parts of the hard drive to do Windows housekeeping or to load program segments for various functions
Now, at the same time and with the same hand... while still using the baton to conduct the orchestra... pick up a bow and play a fiddle... this would be doing something with your video file at the same time as all the other work
You as a person cannot do both at the same time with the same hand
A computer is a LITTLE better, in that it can switch from one kind of task to another very quickly... but not quickly enough for easy video editing
One hard drive is not as good as two which is not as good as three

Very slow Windows 7 boot time

Hey,
I recently bootcamped my MacBook with Windows 7 for the second time and I've noticed a huge difference in booting speeds. I have Windows set as my boot device. After the white screen, the laptop stays at a black screen with a flashing white underscore for around a minute. After that, the computer starts as normal.
How can I remove the black screen, considering there isn't a BIOS for bootcamp?
Thanks in advance,

What happens is Bootcamp has work its magic with the Mac EFI system that is similar to what PC systems call Bios. Its the basics startup instructions for the hardware. Because Windows does not work well with EFI boot systems. A longer boot time can be expected. You can check your Windows portion of the boot with MSconfig although I would not mess with changing anything unless you know what your doing. Otherwise you could corrupt the boot config. I would say my Macbook Pro 2011 takes about 20 seconds to boot into Windows from power up to Windows sign in. Remember your not booting Windows on a PC your booting Windows on a Mac which although BootCamp is a decent way to do that. Its not tweaked as well as say a PC which was designed and built around running Windows. Drivers, hardware, and Bootcamp are Apple. Only Windows is Microsoft. I highly doubt Microsoft worries a lot about making Windows boot well on a Mac.

MOVED: 880gm-e43 with Crucial SSD = very slow windows boot times

This topic has been moved to Windows 64bit.
https://forum-en.msi.com/index.php?topic=155325.0

Hi,
Thank you for your post.
From your description, I see the issue you are facing is there is no menu to choose OS when booting dual boot(Windows 7 & Windows 8). Please let me know if I have misunderstood anything.
It seems that the Windows 7 entry is missing, currently, we can use a tool –
EasyBCD to get it back. After downloading it, choose the Add/Edit panel item, select the OS you're missing and let the program detect it. Then simply click the Add button to add the missing OS entry.
At the meantime, here is a related link which demonstrates how to keep Windows 7 as the default OS in dual boot, you may use it for a reference.
How to Dual-Boot Windows 8 While Keeping Windows 7 As Your Default OS
http://blog.laptopmag.com/how-to-dual-boot-windows-8-while-keeping-windows-7-as-your-default-os
[Please Note: Since the website is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy
of this information.]
Regarding your second questions in your first post, you can refer to the following link to know more about dual boot.
Dual
Booting Explained: How You Can Have Multiple Operating Systems on Your Computer
http://www.howtogeek.com/187789/dual-booting-explained-how-you-can-have-multiple-operating-systems-on-your-computer/
[Please Note: Since the website is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy
of this information.]
Hopefully the information is helpful. Please let me know if you have any questions. Thanks for your time.
Best Regards,
Sophia Sun
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

Very slow DVD image creation: is there a faster way.

Hi to everybody.
I often need to create images from DL DVD2 and each image takes around 45 minutes. All this time for just 7,8Gbytes of datas (using Disk Utility)? Is there a faster software for doing this?
TIA
majortom67

Make sure you set Disk Utility's "Image Format" to "DVD/CD master", not "compressed". (Video data is already compressed, so "compressed" will not be much smaller but takes a lot more computing.)

E4200 Very Slow Windows 7 Wireless to attached HD speeds ( 800k/sec)

I'm running 1.0.03.
I have a Toshiba T400 running Win7 Professional.
I have a WD USB Drive connected to the router. (No problems transffering files to it directly from my laptop)
Distance to router doesn't matter.
Right now, all I would like to do is transfer files [video] to the HD attached to the router so that they can be accessed by anyone - primaily by my PS3.
My wireless speeds range anywhere from 300k/sec to 800k/sec (usually somewhere in the middle - depending on settings I change). My wired speeds range from 3-4MB/sec. Both of which I find unacceptable considering even the theoretical speeds of GBe and USB 2. I've tried disconnected everything but just my computer and the HD from the router as well with no change.
I've tried MTU, RD protocol disabling, firewall disabling, A/V disabling, Homegroup disabling, adjusting properties in the driver properties (for both wired and wirelss), looking for network driver updates... Basically anything Google would throw at me with no luck.
Considering the number of posts I see - I'm guessing it's the router? Has anyone come up with a solution yet or are we stuck waiting for Firmware upgrades?
At this point, my max torrent speeds (2-2.5MB/sec) via wireless are faster than LAN transferring and that's just not right. When I return home, I may just try "bypassing" Local Network and transfer the files via Media FTP and see how that fares.
Thanks.

Did you update the firmware to latest or was it pre-installed. If you have updated the firmware of the router recently then it is recommended to reset the router. Push the reset button on router for 30 seconds, turn off the router wait for 30 seconds and then power it on. After this process reconfigure the router. Power light should blink when you perform the reset process.
Then install the Cisco Connect Software. It will help you in configuring the Router.
But if you want to configure it manually then here are the links for configuring the according to the ISP setup…
For DSL Connection:
http://www6.nohold.net/Cisco2/ukp.aspx?pid=93&login=1&vw=1&app=search&articleid=2210&userrole=Linksy...
For Cable Connection:
http://www6.nohold.net/Cisco2/ukp.aspx?pid=93&login=1&vw=1&app=search&articleid=1040&userrole=Linksy...
Secondly do the rest of the wireless settings again and then check the speed of both wired and wireless connection...

Very slow performance running Mavericks - need troubleshooting help

Hello folks:
I have a MBP 2011 which was upgraded to Mavericks from Mountain Lion about 6 weeks ago. Since then I have had a major performance drop - slow machine, very slow window renderings, etc. I know a number of people have been facing these issues and have been recommended to clean up 3rd party extensions/agents. I ran Etrecheck (report below) and I need some help with fixing the failed kernel extensions and launch daemons. Thanks much!
Pavan
Hardware Information:
MacBook Pro (13-inch, Late 2011)
MacBook Pro - model: MacBookPro8,1
1 2.8 GHz Intel Core i7 CPU: 2 cores
4 GB RAM
Video Information:
Intel HD Graphics 3000 - VRAM: 384 MB
Audio Plug-ins:
BluetoothAudioPlugIn: Version: 1.0 - SDK 10.9
AirPlay: Version: 1.9 - SDK 10.9
AppleAVBAudio: Version: 2.0.0 - SDK 10.9
iSightAudio: Version: 7.7.3 - SDK 10.9
System Software:
OS X 10.9 (13A603) - Uptime: 6 days 4:6:6
Disk Information:
TOSHIBA MK7559GSXF disk0 : (750.16 GB)
EFI (disk0s1) <not mounted>: 209.7 MB
Hurricane (disk0s2) /: 749.3 GB (257.76 GB free)
Recovery HD (disk0s3) <not mounted>: 650 MB
MATSHITADVD-R   UJ-8A8
USB Information:
Western Digital My Book 1148 3 TB
EFI (disk4s1) <not mounted>: 209.7 MB
disk4s2 (disk4s2) <not mounted>: 3 TB
Boot OS X (disk4s3) <not mounted>: 134.2 MB
Apple Computer, Inc. IR Receiver
Apple Inc. FaceTime HD Camera (Built-in)
Memorex TRAVELDRIVE 005B 16.01 GB
EFI (disk2s1) <not mounted>: 209.7 MB
Untitled (disk2s2) /Volumes/Untitled: 15.67 GB (15.63 GB free)
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
FireWire Information:
Thunderbolt Information:
Apple Inc. thunderbolt_bus
Kernel Extensions:
com.wdc.driver.USB_64HP (1.0.0 - SDK 10.6)
Problem System Launch Daemons:
[failed] com.apple.AOSNotificationOSX.plist
[failed] com.apple.installd.plist
[failed] com.apple.softwareupdated.plist
[failed] com.apple.wdhelper.plist
Problem System Launch Agents:
Launch Daemons:
[loaded] com.adobe.fpsaud.plist
[loaded] com.adobe.versioncueCS3.plist
[loaded] com.barebones.textwrangler.plist
[loaded] com.cisco.anyconnect.vpnagentd.plist
[loaded] com.google.keystone.daemon.plist
[loaded] com.microsoft.office.licensing.helper.plist
[loaded] com.oracle.java.Helper-Tool.plist
[loaded] org.macosforge.xquartz.privileged_startx.plist
Launch Agents:
[loaded] com.cisco.anyconnect.gui.plist
[loaded] com.google.keystone.agent.plist
[loaded] com.oracle.java.Java-Updater.plist
[loaded] org.macosforge.xquartz.startx.plist
User Launch Agents:
[failed] com.apple.CSConfigDotMacCert-[redacted]@me.com-SharedServices.Agent.plist
[loaded] com.google.Chrome.framework.plist
User Login Items:
Flux
iTunesHelper
Google Drive
Google Chrome
AdobeResourceSynchronizer
3rd Party Preference Panes:
Flash Player
Java
Internet Plug-ins::
o1dbrowserplugin: Version: 4.9.1.16010
Default Browser: Version: 537 - SDK 10.9
Flip4Mac WMV Plugin: Version: 2.2.0.49
Loki: Version: 3.0
net.juniper.DSSafariExtensions: Version: (null)
RealPlayer Plugin: Version: Unknown
FlashPlayer-10.6: Version: 11.9.900.170 - SDK 10.6
DivXBrowserPlugin: Version: 1.3
Silverlight: Version: 5.1.20513.0 - SDK 10.6
Flash Player: Version: 11.9.900.170 - SDK 10.6
AmazonMP3DownloaderPlugin: Version: Unknown
googletalkbrowserplugin: Version: 4.9.1.16010
npgtpo3dautoplugin: Version: 0.1.44.29 - SDK 10.5
iPhotoPhotocast: Version: 6.0
QuickTime Plugin: Version: 7.7.3
SharePointBrowserPlugin: Version: 14.3.9 - SDK 10.6
JavaAppletPlugin: Version: Java 7 Update 45
User Internet Plug-ins::
Picasa: Version: 1.0
Google Earth Web Plug-in: Version: 7.1
Bad Fonts:
None
Old applications:
Audacity: Version: 1.3.14.0 - SDK 10.4
/Applications/Audacity/Audacity.app
Hugin: Version: 2011.4.0 - SDK 10.4
/Applications/Hugin/Hugin.app
Keynote: Version: 5.3 - SDK 10.5
/Applications/iWork '09/Keynote.app
Microsoft Alerts Daemon: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/Microsoft Alerts Daemon.app
Microsoft AutoUpdate: Version: 2.3.6 - SDK 10.4
/Library/Application Support/Microsoft/MAU2.0/Microsoft AutoUpdate.app
Microsoft Chart Converter: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/Microsoft Chart Converter.app
Microsoft Clip Gallery: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/Microsoft Clip Gallery.app
Microsoft Database Daemon: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/Microsoft Database Daemon.app
Microsoft Database Utility: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/Microsoft Database Utility.app
Microsoft Document Connection: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Microsoft Document Connection.app
Microsoft Error Reporting: Version: 2.2.9 - SDK 10.4
/Library/Application Support/Microsoft/MERP2.0/Microsoft Error Reporting.app
Microsoft Excel: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Microsoft Excel.app
Microsoft Graph: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/Microsoft Graph.app
Microsoft Language Register: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Additional Tools/Microsoft Language Register/Microsoft Language Register.app
Microsoft Office Reminders: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/Microsoft Office Reminders.app
Microsoft Outlook: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Microsoft Outlook.app
Microsoft PowerPoint: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Microsoft PowerPoint.app
Microsoft Ship Asserts: Version: 1.1.4 - SDK 10.4
/Library/Application Support/Microsoft/MERP2.0/Microsoft Ship Asserts.app
Microsoft Upload Center: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/Microsoft Upload Center.app
Microsoft Word: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Microsoft Word.app
My Day: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/My Day.app
Open XML for Excel: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/Open XML for Excel.app
PTBatcherGUI: Version: 2011.4.0 - SDK 10.4
/Applications/Hugin/PTBatcherGUI.app
Picasa: Version: 3.9.16 - SDK 10.4
/Applications/Picasa.app
SLLauncher: Version: 1.0 - SDK 10.5
/Library/Application Support/Microsoft/Silverlight/OutOfBrowser/SLLauncher.app
Solver: Version: 1.0 - SDK 10.5
/Applications/Microsoft Office 2011/Office/Add-Ins/Solver.app
Spotify: Version: 0.8.4.107.g4fa0003f - SDK 10.5
/Applications/Spotify.app
SyncServicesAgent: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/SyncServicesAgent.app
calibrate_lens_gui: Version: 2011.4.0 - SDK 10.4
/Applications/Hugin/calibrate_lens_gui.app
Time Machine:
Skip System Files: NO
Mobile backups: ON
Auto backup: YES
Volumes being backed up:
Hurricane: Disk size: 697.84 GB Disk used: 457.78 GB
Destinations:
Gasolina [Local] (Last used)
Total size: 3
Total number of backups: 18
Oldest backup: 2013-07-09 19:11:24 +0000
Last backup: 2013-12-13 19:35:36 +0000
Size of backup disk: Excellent
Backup size 3 > (Disk size 697.84 GB X 3)
Time Machine details may not be accurate.
All volumes being backed up may not be listed.
Top Processes by CPU:
      22% storeagent
      2% WindowServer
      1% backupd
      1% Google Chrome
      1% EtreCheck
Top Processes by Memory:
119 MB Google Chrome
102 MB Google Chrome Helper
82 MB mds_stores
57 MB Finder
33 MB WindowServer
Virtual Memory Statistics:
45 MB Free RAM
792 MB Active RAM
748 MB Inactive RAM
1.06 GB Wired RAM
37.63 GB Page-ins
1.98 GB Page-outs

Here’s your report with some comments:
Hardware Information:
MacBook Pro (13-inch, Late 2011)
MacBook Pro - model: MacBookPro8,1
1 2.8 GHz Intel Core i7 CPU: 2 cores
4 GB RAM
Video Information:
Intel HD Graphics 3000 - VRAM: 384 MB
Audio Plug-ins:
BluetoothAudioPlugIn: Version: 1.0 - SDK 10.9
AirPlay: Version: 1.9 - SDK 10.9
AppleAVBAudio: Version: 2.0.0 - SDK 10.9
iSightAudio: Version: 7.7.3 - SDK 10.9
System Software:
OS X 10.9 (13A603) - Uptime: 6 days 4:6:6
Disk Information:
TOSHIBA MK7559GSXF disk0 : (750.16 GB)
EFI (disk0s1) <not mounted>: 209.7 MB
Hurricane (disk0s2) /: 749.3 GB (257.76 GB free)
Recovery HD (disk0s3) <not mounted>: 650 MB
MATSHITADVD-R   UJ-8A8
USB Information:
Western Digital My Book 1148 3 TB    WD drives are one of the worst things that can happen to a mac. They have software on the drive and also in the firmware of the drive enclosure that is incompatible with Mavericks. The software that they also want you to install on your mac (to run the drive with the shitware on it that is incompatible with Mavericks) is also incompatible with Mavericks. The best thing to do with this drive is to open it and remove the hard drive and put it into a new (non-WD) enclosure. Then smash the WD enclosure into little bits with a sledgehammer and mail it back to WD.
EFI (disk4s1) <not mounted>: 209.7 MB
disk4s2 (disk4s2) <not mounted>: 3 TB
Boot OS X (disk4s3) <not mounted>: 134.2 MB
Apple Computer, Inc. IR Receiver
Apple Inc. FaceTime HD Camera (Built-in)
Memorex TRAVELDRIVE 005B 16.01 GB
EFI (disk2s1) <not mounted>: 209.7 MB
Untitled (disk2s2) /Volumes/Untitled: 15.67 GB (15.63 GB free)
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
FireWire Information:
Thunderbolt Information:
Apple Inc. thunderbolt_bus
Kernel Extensions:
com.wdc.driver.USB_64HP (1.0.0 - SDK 10.6)     This would be part of the shitware that you installed from WD. I would uninstall the WD application that installs this driver. If the driver is still there after that, I'd look for the extension in /System/Library/Extensions and delete it from there. This may have damaged your kernel, though. If your performance is not improved after removing the WD app and this extension, you should probably back up your documents, erase your HD, and do a clean reinstall of Mavericks.
Problem System Launch Daemons:
[failed] com.apple.AOSNotificationOSX.plist
[failed] com.apple.installd.plist
[failed] com.apple.softwareupdated.plist
[failed] com.apple.wdhelper.plist    These four are all apple software. I would try repairing your hard drive: Boot into your recovery partition (restart, hold down ⌘R until you see the Apple logo), and use Disk Utility to repair your hard drive. Repair permissions too while you're there. OS X: About OS X Recovery . Then restart, reassess your mac’s performance, and rerun Etrecheck. If that doesn’t work, I’d reinstall Mavericks over your current installation. If that doesn’t work, I’d do a clean install.
Problem System Launch Agents:
Launch Daemons:
[loaded] com.adobe.fpsaud.plist
[loaded] com.adobe.versioncueCS3.plist
[loaded] com.barebones.textwrangler.plist
[loaded] com.cisco.anyconnect.vpnagentd.plist
[loaded] com.google.keystone.daemon.plist    spyware from google
[loaded] com.microsoft.office.licensing.helper.plist
[loaded] com.oracle.java.Helper-Tool.plist
[loaded] org.macosforge.xquartz.privileged_startx.plist
Launch Agents:
[loaded] com.cisco.anyconnect.gui.plist
[loaded] com.google.keystone.agent.plist
[loaded] com.oracle.java.Java-Updater.plist
[loaded] org.macosforge.xquartz.startx.plist
User Launch Agents:
[failed] com.apple.CSConfigDotMacCert-[redacted]@me.com-SharedServices.Agent.plist   see the suggestions above.
[loaded] com.google.Chrome.framework.plist    This is why I prefer Safari. It doesn’t install all this extra junk.
User Login Items:
Flux
iTunesHelper
Google Drive   Last I heard Google drive was incompatible with Mavericks.
Google Chrome
AdobeResourceSynchronizer
3rd Party Preference Panes:
Flash Player
Java
Internet Plug-ins::   Way too many of these. If you have poor browser performance, get rid of these, and then only reinstall ones you absolutely need, and make sure they are mavericks compatible and up-to-date.
o1dbrowserplugin: Version: 4.9.1.16010
Default Browser: Version: 537 - SDK 10.9
Flip4Mac WMV Plugin: Version: 2.2.0.49
Loki: Version: 3.0
net.juniper.DSSafariExtensions: Version: (null)
RealPlayer Plugin: Version: Unknown
FlashPlayer-10.6: Version: 11.9.900.170 - SDK 10.6
DivXBrowserPlugin: Version: 1.3
Silverlight: Version: 5.1.20513.0 - SDK 10.6
Flash Player: Version: 11.9.900.170 - SDK 10.6
AmazonMP3DownloaderPlugin: Version: Unknown
googletalkbrowserplugin: Version: 4.9.1.16010
npgtpo3dautoplugin: Version: 0.1.44.29 - SDK 10.5
iPhotoPhotocast: Version: 6.0
QuickTime Plugin: Version: 7.7.3
SharePointBrowserPlugin: Version: 14.3.9 - SDK 10.6
JavaAppletPlugin: Version: Java 7 Update 45
User Internet Plug-ins::
Picasa: Version: 1.0
Google Earth Web Plug-in: Version: 7.1
Bad Fonts:
None
Old applications:
Audacity: Version: 1.3.14.0 - SDK 10.4
/Applications/Audacity/Audacity.app
Hugin: Version: 2011.4.0 - SDK 10.4
/Applications/Hugin/Hugin.app
Keynote: Version: 5.3 - SDK 10.5
/Applications/iWork '09/Keynote.app
Microsoft Alerts Daemon: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/Microsoft Alerts Daemon.app
Microsoft AutoUpdate: Version: 2.3.6 - SDK 10.4
/Library/Application Support/Microsoft/MAU2.0/Microsoft AutoUpdate.app
Microsoft Chart Converter: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/Microsoft Chart Converter.app
Microsoft Clip Gallery: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/Microsoft Clip Gallery.app
Microsoft Database Daemon: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/Microsoft Database Daemon.app
Microsoft Database Utility: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/Microsoft Database Utility.app
Microsoft Document Connection: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Microsoft Document Connection.app
Microsoft Error Reporting: Version: 2.2.9 - SDK 10.4
/Library/Application Support/Microsoft/MERP2.0/Microsoft Error Reporting.app
Microsoft Excel: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Microsoft Excel.app
Microsoft Graph: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/Microsoft Graph.app
Microsoft Language Register: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Additional Tools/Microsoft Language Register/Microsoft Language Register.app
Microsoft Office Reminders: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/Microsoft Office Reminders.app
Microsoft Outlook: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Microsoft Outlook.app
Microsoft PowerPoint: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Microsoft PowerPoint.app
Microsoft Ship Asserts: Version: 1.1.4 - SDK 10.4
/Library/Application Support/Microsoft/MERP2.0/Microsoft Ship Asserts.app
Microsoft Upload Center: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/Microsoft Upload Center.app
Microsoft Word: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Microsoft Word.app
My Day: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/My Day.app
Open XML for Excel: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/Open XML for Excel.app
PTBatcherGUI: Version: 2011.4.0 - SDK 10.4
/Applications/Hugin/PTBatcherGUI.app
Picasa: Version: 3.9.16 - SDK 10.4
/Applications/Picasa.app
SLLauncher: Version: 1.0 - SDK 10.5
/Library/Application Support/Microsoft/Silverlight/OutOfBrowser/SLLauncher.app
Solver: Version: 1.0 - SDK 10.5
/Applications/Microsoft Office 2011/Office/Add-Ins/Solver.app
Spotify: Version: 0.8.4.107.g4fa0003f - SDK 10.5
/Applications/Spotify.app
SyncServicesAgent: Version: 14.3.9 - SDK 10.5
/Applications/Microsoft Office 2011/Office/SyncServicesAgent.app
calibrate_lens_gui: Version: 2011.4.0 - SDK 10.4
/Applications/Hugin/calibrate_lens_gui.app
Time Machine:
Skip System Files: NO
Mobile backups: ON
Auto backup: YES
Volumes being backed up:
Hurricane: Disk size: 697.84 GB Disk used: 457.78 GB
Destinations:
Gasolina [Local] (Last used)
Total size: 3
Total number of backups: 18
Oldest backup: 2013-07-09 19:11:24 +0000
Last backup: 2013-12-13 19:35:36 +0000
Size of backup disk: Excellent
Backup size 3 > (Disk size 697.84 GB X 3)
Time Machine details may not be accurate.
All volumes being backed up may not be listed.
Top Processes by CPU:
      22% storeagent
      2% WindowServer
      1% backupd
      1% Google Chrome
      1% EtreCheck
Top Processes by Memory:
119 MB Google Chrome
102 MB Google Chrome Helper
82 MB mds_stores
57 MB Finder
33 MB WindowServer
Virtual Memory Statistics:
45 MB Free RAM
792 MB Active RAM
748 MB Inactive RAM
1.06 GB Wired RAM
37.63 GB Page-ins
1.98 GB Page-outs This is the highest amount of page-outs I have ever seen. I'd get rid of Chrome and Google Drive. Dropbox works fine and doesn't screw up my mac.

Very slow graphics when using AMD Radeon HD 6490M with Yosemite

I'm using a 15" MacBook Pro early 2011. When I switch to the GPU using gfxCardStatus (or because an app requires it), all graphics become very slow: window dragging, window miniaturize animation, moving the mouse in the menubar etc. 3D view in Maps.app is very slow. All is fine when using the integrated Intel HD 3000. I did not have this problem with Yosemite Developer Previews (I did not install the GMs), nor with Mavericks.
I tried using AMD kext from the DP, but things are worst (I suppose the kext are not loaded at all because the signature does not match).

Hi. I tried to do that with the same download package on my Pavilion DV6 CTO Quad edition and it fails to install the driver because of a conflict with the C++ Redistributable 2010 package build into the installer. Does anyone know if HP is going to update the switchable graphic drivers for Windows 8? They better!

ZCM 11 very slow Windows 7 image restore

Similar Messages

Maybe you are looking for