Zen 2gb and Vongo

Is it possible to use the Zen 2gb and Vongo downloads, in other words are the Vongo downloads too big in file size to be viewed or do I need a larger size player or a SD card to upload them to?
If its not possible to do this then why do they advertise Vongo with these players with smaller flash dri'ves?

I can tell you that the Zen 2gb is not as great with audio books as it ought to be.
Audible?format audio books have chapter markings that the Zen can see. Overdri've?Media files?do not.
Yes, you can bookmark. However, when you go to the bookmark, the player does not remember that the bookmarked file was part of a playlist. Therefore, it loads only the one file and stops playing when it gets to the end. At that point you have to go back through the main menu to reload your playlist.
The "resume" function would make the bookmark problem less annoying, if it worked properly. The player will remember where you stopped and begin there the next time you turn the player on, unless you wait more than 2 hours. In that case, it starts at the beginning of the track and you have to FF till you find your place (hopefully you remembered to note the timer position before shutting down). This is the method I've settled on, because although I have to FF to my place every morning and evening, at least I don't have to keep reloading playlist.
Interestingly, although you can't bookmark videos on the Zen, you don't need to, because it remembers where you left off playing it no matter how long you wait, and even after synching.

Similar Messages

  • Zen 2gb and audio book chapters and bookma

    Hello,
    Right now I have a Zen Stone which I use mainly to download audio books and which I have outgrown. It was a good, cheap starter mp3, but now I want something better. (The tech upgrade?bug strikes again, I guess.) The main peeeve I have with the Zen Stone is that I cannot bookmark where I stopped in a book's chapter. Books download in sections whcih contain more that one actual chapte, so, when I have to recharge the battery, the Stone restarts at the last section, not where I quit to recharge. Thus, I have to re-listen to old material. Also, since there is no screen, I can't see where and what section/chapter I am anyway.
    Will a better model Zen allow me to save and bookmark where I am in a book so that i can restart anywhere without going back over old material? Will I be able to see sections nad chapter headings (section 4, chapter6, e.g.) on the screen.
    Any help appreciated. I am fairly new to mp3-land, but not to computers. Thanks

    I can tell you that the Zen 2gb is not as great with audio books as it ought to be.
    Audible?format audio books have chapter markings that the Zen can see. Overdri've?Media files?do not.
    Yes, you can bookmark. However, when you go to the bookmark, the player does not remember that the bookmarked file was part of a playlist. Therefore, it loads only the one file and stops playing when it gets to the end. At that point you have to go back through the main menu to reload your playlist.
    The "resume" function would make the bookmark problem less annoying, if it worked properly. The player will remember where you stopped and begin there the next time you turn the player on, unless you wait more than 2 hours. In that case, it starts at the beginning of the track and you have to FF till you find your place (hopefully you remembered to note the timer position before shutting down). This is the method I've settled on, because although I have to FF to my place every morning and evening, at least I don't have to keep reloading playlist.
    Interestingly, although you can't bookmark videos on the Zen, you don't need to, because it remembers where you left off playing it no matter how long you wait, and even after synching.

  • My Zen 2gb wont even start up anymore

    Hello,?When i inserted my Creative Zen 2GB and was planning on removing some music from it..i picked out the music folders and pressed <delete>, so it started deleting, but at some point it didn't go on for 0 minutes so i did?<ctrl> + <alt> + <delete> and i closed down the process manually. Then i pulled out my Creative Zen and it did NOT go to its menu's again it kept saying? <Connected> (with the PC). Then i tried to plug it back in and again and again but it had no result, it kept saying <connected>.After i while i quited trying and was looking at my Zen when i saw the <reset> button on the side. I pressed this with a blunt needle and the sreen went black...and now i cant Boot it up or do anything with it, when i plug it into my PC i DO here a sound that something got connected but my Zen's sreen doesn't light up. So please, does anyone have ANY suggesting on how to solve this problem?Should i get it repaired or...
    Please help,?Mark

    I Tried now, but it seems my Zen doesn't work anymore, because if i try to turn it on, on the side, the blue light doesn't pop on :S..and there is no-way i can get to the battery because this Zen doesn't contain any screws..so i cant check if that is the problem.

  • Zen 2GB - a blue light is flicker

    Hello,
    first of all, please excuse my bad english. Unfortunately there is no german board.
    I've bought an Zen 2GB and have watched the following: Sometimes the screen flickers in a blue light and turns off after about one second. Remarkable is, that when it happens the player is not in use, for example the player is laying on the table and is turned off. This flickering effect also happens, when I plug in an earphone. But it doesn't happen with every earphone (only some models, I've tested) and only in about 80 percent of the times, when I plug it in.
    Recently I've exchanged the player at my local dealer. But the new one still shows the same effect.
    My question now: Has anyone made the same experience with his Zen and is the Zen not ok?
    I would be glad for your answers.
    Bernd

    I also encountered this same behavior when using a different headphone for my ZEN 4GB...sometimes it restarts, sometimes it totally hangs up..leaving only the blue light on... I cannot turn it off... I have to do a reset on the thing which forced me to bring along a hair pin everyday... I think it has something to do with the antenna incorporated in the headphone slot...any other idea what's causing this?Message Edited by daywalkerz on 02-2-200809:4 PM

  • Disk Full on Zen 2GB with 1,70GB of space le

    Hey everyone,
    I have a Zen 2GB and when I try to rip songs of a cd onto my Zen, it says the disk is full and I should make more room on my computer(?).
    In the Creative Audio CD ripper I did not select the option to rip the files to my computer and on my Zen is still ,7 GB left!
    I searched the forums, but couldn't find a solution there.
    I also tried a full format, a reset of the settings and a firmware upgrade, but nothing seems to work..
    Please help me out, all suggestions are welcome!
    Thanks.

    Nope, that didn't work either..
    It is also quite strange that the cd ripper talks about "Computer" as the location being full. The only option checked is to copy the ripped music to the Zen music device and NOT to the computer (eitherway; there is also plenty of space on my computer).
    I completely removed and reinstalled the Creative software, but that also didn't help...
    Message Edited by Wesko on 04-23-2008 06:32 AM

  • Is it worthy to buy a Zen with 2Gb and a SD card of 4 or is it better to buy a Zen with 4

    Hi.
    I'm thinking on buying a Zen, but i'm a bit confused on the issue of if is it better to buy a Zen with 4Gb or a Zen with 2Gb and a SD card with 4Gb, because the diference on the pricefrom the 2Gb to the 4Gb fits a SD card with 4Gb, and will result in a Zen with 6Gb...
    Does the zen works fine with the reading times of the SD cards? Or does the performance drops when reading from the card?
    I would apreciate your experience/knowing opinions.
    Thanks
    BM

    Ask that question here.http://epizenter.net/e07_plugins/forum/forum.php

  • Zen 2GB Battery Issue - Please help!

    $? I bought two Creative Zen 2GB as their battery life is up to 30 hours. I have a Microsoft Zune and it gets the 4 hours listed but both of the Zen's only get 0- hours per full charge. I fully charge, then run the recovery tool and run disk clean up, format, new firmware. I then add all mp3's at 28 bitrate, EQ off, bass off and keep the volume on 3. In the setup I the brightness down as far as it will go at 0%, I think you should be able to set it to 0%. But what am I missing to only get 0-2 hour max on these two new units? I recently read about Idle shutdown, but yesterday I charged the Zen 8 hours to be sure, then with all the optimal settings I cut it on at 0pm and let it run througout the night and at 9am it had very little charge left...please help with any ideas/suggestions as I just get links from Creative tech telling me things I am already doing.
    Mickey

    Micktarheel wrote:
    Excellent, thanks for the replies and I read about the lock function online but it said for 4GB and up I think, but not 2GB. I thought, even with the screen at the lowest, 0% that it was too much lcd and a battery drainer...thanks!
    Yes, I have the 2G ZEN player and it does have the "lock function" (often on the Creative's web site they neglect to mention the 2G) - I "lock it" every time I listen to my audio books. By using this function it "closes" (blackens) ?the LCD screen and saves the battery considerably.
    When I first bought this player it was the first time I had an internal battery, all the other ones I had used -AAA battery. I was hesitant about using the type of battery in the ZEN player but I can listen ALL day and ALL night and still have battery life left. Then I recharge the battery in the wee hours of the morning, ready to listen to more books and music that day.
    Just some thoughts,
    katdesigns

  • ZEN 2GB driver with vi

    I purchased a ZEN MP3 Player 2GB, using windows vista home basic and cannot install the driver for this device on my computer. I have tried many times to install it but all attempt had the same result with the message on my display that the driver cannot be found, please contact creative.
    I am not talking about the software which comes on a CD, I am talking about once I plug in the device my computer with windows vista home basic simply is unable to find the driver or whatsoever. Once I have contacted the local dealer and they recommended that I should download the latest firmware for my device which I did but the result was the same because to install the firmware you need to plug in your device but since my device cannot be installed the firmware does not recognise any device and cannot be installed. After that the local dealer changed the device for me but nevertheless the new device cannot be installed as well. Is there anyone who can help me out with this problem
    It is kind of frustrating if you buy a Christmas present for your partner and it cannot be used even you install, uninstall, install, uninstall the whole thing a several times.
    Thanks, your help is appreciated here

    I have got my Zen Stone Plus working like this: I plugged the Zen in and waited for Vista to do its stuff, then when the installed failed I was able to use the browse function it offered, when you don't have a disk, I just put c:/ and let Vista search my hard drive. Vista was able to find the drivers and complete the install. If I look in devise manager it now has the same drivers and route as stormy3 (see other post) Working fine now.

  • Zen Kernel and new ati radeon oss driver

    Hey together!
    A few days ago I get new ati-driver from testing and since then, I can't start the xserver with the zen kernel and ums. I can use the normal kernel 2.6.33 normally.
    Here is my Xorg log:
    X.Org X Server 1.7.6
    Release Date: 2010-03-17
    X Protocol Version 11, Revision 0
    Build Operating System: Linux 2.6.33-ARCH i686
    Current Operating System: Linux linux-laptop 2.6.33-ZEN #1 ZEN SMP PREEMPT Fri Mar 5 13:29:19 CET 2010 i686
    Kernel command line: root=/dev/disk/by-uuid/5394d0b7-4952-4f87-87bc-a4762f73b8c4 ro quiet
    Build Date: 18 March 2010 07:32:34PM
    Current version of pixman: 0.16.6
    Before reporting problems, check http://wiki.x.org
    to make sure that you have the latest version.
    Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
    (==) Log file: "/var/log/Xorg.0.log", Time: Fri Mar 19 14:12:54 2010
    (II) Loader magic: 0x81e4c60
    (II) Module ABI versions:
    X.Org ANSI C Emulation: 0.4
    X.Org Video Driver: 6.0
    X.Org XInput driver : 7.0
    X.Org Server Extension : 2.0
    (--) using VT number 7
    (--) PCI:*(0:1:0:0) 1002:5653:144d:e003 ATI Technologies Inc Radeon Mobility X700 (PCIE) rev 0, Mem @ 0xd0000000/134217728, 0xc0100000/65536, I/O @ 0x00003000/256, BIOS @ 0x????????/131072
    (==) Using default built-in configuration (30 lines)
    (==) --- Start of built-in configuration ---
    Section "Device"
    Identifier "Builtin Default ati Device 0"
    Driver "ati"
    EndSection
    Section "Screen"
    Identifier "Builtin Default ati Screen 0"
    Device "Builtin Default ati Device 0"
    EndSection
    Section "Device"
    Identifier "Builtin Default vesa Device 0"
    Driver "vesa"
    EndSection
    Section "Screen"
    Identifier "Builtin Default vesa Screen 0"
    Device "Builtin Default vesa Device 0"
    EndSection
    Section "Device"
    Identifier "Builtin Default fbdev Device 0"
    Driver "fbdev"
    EndSection
    Section "Screen"
    Identifier "Builtin Default fbdev Screen 0"
    Device "Builtin Default fbdev Device 0"
    EndSection
    Section "ServerLayout"
    Identifier "Builtin Default Layout"
    Screen "Builtin Default ati Screen 0"
    Screen "Builtin Default vesa Screen 0"
    Screen "Builtin Default fbdev Screen 0"
    EndSection
    (==) --- End of built-in configuration ---
    (==) ServerLayout "Builtin Default Layout"
    (**) |-->Screen "Builtin Default ati Screen 0" (0)
    (**) | |-->Monitor "<default monitor>"
    (**) | |-->Device "Builtin Default ati Device 0"
    (==) No monitor specified for screen "Builtin Default ati Screen 0".
    Using a default monitor configuration.
    (**) |-->Screen "Builtin Default vesa Screen 0" (1)
    (**) | |-->Monitor "<default monitor>"
    (**) | |-->Device "Builtin Default vesa Device 0"
    (==) No monitor specified for screen "Builtin Default vesa Screen 0".
    Using a default monitor configuration.
    (**) |-->Screen "Builtin Default fbdev Screen 0" (2)
    (**) | |-->Monitor "<default monitor>"
    (**) | |-->Device "Builtin Default fbdev Device 0"
    (==) No monitor specified for screen "Builtin Default fbdev Screen 0".
    Using a default monitor configuration.
    (==) Automatically adding devices
    (==) Automatically enabling devices
    (==) FontPath set to:
    /usr/share/fonts/misc,
    /usr/share/fonts/100dpi:unscaled,
    /usr/share/fonts/75dpi:unscaled,
    /usr/share/fonts/TTF,
    /usr/share/fonts/Type1
    (==) ModulePath set to "/usr/lib/xorg/modules"
    (II) Cannot locate a core pointer device.
    (II) Cannot locate a core keyboard device.
    (II) The server relies on HAL to provide the list of input devices.
    If no devices become available, reconfigure HAL or disable AutoAddDevices.
    (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
    (II) LoadModule: "extmod"
    (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
    (II) Module extmod: vendor="X.Org Foundation"
    compiled for 1.7.6, module version = 1.0.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 2.0
    (II) Loading extension MIT-SCREEN-SAVER
    (II) Loading extension XFree86-VidModeExtension
    (II) Loading extension XFree86-DGA
    (II) Loading extension DPMS
    (II) Loading extension XVideo
    (II) Loading extension XVideo-MotionCompensation
    (II) Loading extension X-Resource
    (II) LoadModule: "dbe"
    (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
    (II) Module dbe: vendor="X.Org Foundation"
    compiled for 1.7.6, module version = 1.0.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 2.0
    (II) Loading extension DOUBLE-BUFFER
    (II) LoadModule: "glx"
    (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
    (II) Module glx: vendor="X.Org Foundation"
    compiled for 1.7.6, module version = 1.0.0
    ABI class: X.Org Server Extension, version 2.0
    (==) AIGLX enabled
    (II) Loading extension GLX
    (II) LoadModule: "record"
    (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
    (II) Module record: vendor="X.Org Foundation"
    compiled for 1.7.6, module version = 1.13.0
    Module class: X.Org Server Extension
    ABI class: X.Org Server Extension, version 2.0
    (II) Loading extension RECORD
    (II) LoadModule: "dri"
    (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
    (II) Module dri: vendor="X.Org Foundation"
    compiled for 1.7.6, module version = 1.0.0
    ABI class: X.Org Server Extension, version 2.0
    (II) Loading extension XFree86-DRI
    (II) LoadModule: "dri2"
    (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
    (II) Module dri2: vendor="X.Org Foundation"
    compiled for 1.7.6, module version = 1.1.0
    ABI class: X.Org Server Extension, version 2.0
    (II) Loading extension DRI2
    (II) LoadModule: "ati"
    (II) Loading /usr/lib/xorg/modules/drivers/ati_drv.so
    (II) Module ati: vendor="X.Org Foundation"
    compiled for 1.7.5.902, module version = 6.12.192
    Module class: X.Org Video Driver
    ABI class: X.Org Video Driver, version 6.0
    (II) LoadModule: "radeon"
    (II) Loading /usr/lib/xorg/modules/drivers/radeon_drv.so
    (II) Module radeon: vendor="X.Org Foundation"
    compiled for 1.7.5.902, module version = 6.12.192
    Module class: X.Org Video Driver
    ABI class: X.Org Video Driver, version 6.0
    (II) LoadModule: "vesa"
    (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so
    (II) Module vesa: vendor="X.Org Foundation"
    compiled for 1.7.5, module version = 2.3.0
    Module class: X.Org Video Driver
    ABI class: X.Org Video Driver, version 6.0
    (II) LoadModule: "fbdev"
    (WW) Warning, couldn't open module fbdev
    (II) UnloadModule: "fbdev"
    (EE) Failed to load module "fbdev" (module does not exist, 0)
    (II) RADEON: Driver for ATI Radeon chipsets:
    ATI Radeon Mobility X600 (M24) 3150 (PCIE), ATI FireMV 2400 (PCI),
    ATI Radeon Mobility X300 (M24) 3152 (PCIE),
    ATI FireGL M24 GL 3154 (PCIE), ATI Radeon X600 (RV380) 3E50 (PCIE),
    ATI FireGL V3200 (RV380) 3E54 (PCIE), ATI Radeon IGP320 (A3) 4136,
    ATI Radeon IGP330/340/350 (A4) 4137, ATI Radeon 9500 AD (AGP),
    ATI Radeon 9500 AE (AGP), ATI Radeon 9600TX AF (AGP),
    ATI FireGL Z1 AG (AGP), ATI Radeon 9800SE AH (AGP),
    ATI Radeon 9800 AI (AGP), ATI Radeon 9800 AJ (AGP),
    ATI FireGL X2 AK (AGP), ATI Radeon 9600 AP (AGP),
    ATI Radeon 9600SE AQ (AGP), ATI Radeon 9600XT AR (AGP),
    ATI Radeon 9600 AS (AGP), ATI FireGL T2 AT (AGP), ATI Radeon 9650,
    ATI FireGL RV360 AV (AGP), ATI Radeon 7000 IGP (A4+) 4237,
    ATI Radeon 8500 AIW BB (AGP), ATI Radeon 8500 AIW BC (AGP),
    ATI Radeon IGP320M (U1) 4336, ATI Radeon IGP330M/340M/350M (U2) 4337,
    ATI Radeon Mobility 7000 IGP 4437, ATI Radeon 9000/PRO If (AGP/PCI),
    ATI Radeon 9000 Ig (AGP/PCI), ATI Radeon X800 (R420) JH (AGP),
    ATI Radeon X800PRO (R420) JI (AGP),
    ATI Radeon X800SE (R420) JJ (AGP), ATI Radeon X800 (R420) JK (AGP),
    ATI Radeon X800 (R420) JL (AGP), ATI FireGL X3 (R420) JM (AGP),
    ATI Radeon Mobility 9800 (M18) JN (AGP),
    ATI Radeon X800 SE (R420) (AGP), ATI Radeon X800XT (R420) JP (AGP),
    ATI Radeon X800 VE (R420) JT (AGP), ATI Radeon X850 (R480) (AGP),
    ATI Radeon X850 XT (R480) (AGP), ATI Radeon X850 SE (R480) (AGP),
    ATI Radeon X850 PRO (R480) (AGP), ATI Radeon X850 XT PE (R480) (AGP),
    ATI Radeon Mobility M7 LW (AGP),
    ATI Mobility FireGL 7800 M7 LX (AGP),
    ATI Radeon Mobility M6 LY (AGP), ATI Radeon Mobility M6 LZ (AGP),
    ATI FireGL Mobility 9000 (M9) Ld (AGP),
    ATI Radeon Mobility 9000 (M9) Lf (AGP),
    ATI Radeon Mobility 9000 (M9) Lg (AGP), ATI Radeon 9700 Pro ND (AGP),
    ATI Radeon 9700/9500Pro NE (AGP), ATI Radeon 9600TX NF (AGP),
    ATI FireGL X1 NG (AGP), ATI Radeon 9800PRO NH (AGP),
    ATI Radeon 9800 NI (AGP), ATI FireGL X2 NK (AGP),
    ATI Radeon 9800XT NJ (AGP),
    ATI Radeon Mobility 9600/9700 (M10/M11) NP (AGP),
    ATI Radeon Mobility 9600 (M10) NQ (AGP),
    ATI Radeon Mobility 9600 (M11) NR (AGP),
    ATI Radeon Mobility 9600 (M10) NS (AGP),
    ATI FireGL Mobility T2 (M10) NT (AGP),
    ATI FireGL Mobility T2e (M11) NV (AGP), ATI Radeon QD (AGP),
    ATI Radeon QE (AGP), ATI Radeon QF (AGP), ATI Radeon QG (AGP),
    ATI FireGL 8700/8800 QH (AGP), ATI Radeon 8500 QL (AGP),
    ATI Radeon 9100 QM (AGP), ATI Radeon 7500 QW (AGP/PCI),
    ATI Radeon 7500 QX (AGP/PCI), ATI Radeon VE/7000 QY (AGP/PCI),
    ATI Radeon VE/7000 QZ (AGP/PCI), ATI ES1000 515E (PCI),
    ATI Radeon Mobility X300 (M22) 5460 (PCIE),
    ATI Radeon Mobility X600 SE (M24C) 5462 (PCIE),
    ATI FireGL M22 GL 5464 (PCIE), ATI Radeon X800 (R423) UH (PCIE),
    ATI Radeon X800PRO (R423) UI (PCIE),
    ATI Radeon X800LE (R423) UJ (PCIE),
    ATI Radeon X800SE (R423) UK (PCIE),
    ATI Radeon X800 XTP (R430) (PCIE), ATI Radeon X800 XL (R430) (PCIE),
    ATI Radeon X800 SE (R430) (PCIE), ATI Radeon X800 (R430) (PCIE),
    ATI FireGL V7100 (R423) (PCIE), ATI FireGL V5100 (R423) UQ (PCIE),
    ATI FireGL unknown (R423) UR (PCIE),
    ATI FireGL unknown (R423) UT (PCIE),
    ATI Mobility FireGL V5000 (M26) (PCIE),
    ATI Mobility FireGL V5000 (M26) (PCIE),
    ATI Mobility Radeon X700 XL (M26) (PCIE),
    ATI Mobility Radeon X700 (M26) (PCIE),
    ATI Mobility Radeon X700 (M26) (PCIE),
    ATI Radeon X550XTX 5657 (PCIE), ATI Radeon 9100 IGP (A5) 5834,
    ATI Radeon Mobility 9100 IGP (U3) 5835,
    ATI Radeon XPRESS 200 5954 (PCIE),
    ATI Radeon XPRESS 200M 5955 (PCIE), ATI Radeon 9250 5960 (AGP),
    ATI Radeon 9200 5961 (AGP), ATI Radeon 9200 5962 (AGP),
    ATI Radeon 9200SE 5964 (AGP), ATI FireMV 2200 (PCI),
    ATI ES1000 5969 (PCI), ATI Radeon XPRESS 200 5974 (PCIE),
    ATI Radeon XPRESS 200M 5975 (PCIE),
    ATI Radeon XPRESS 200 5A41 (PCIE),
    ATI Radeon XPRESS 200M 5A42 (PCIE),
    ATI Radeon XPRESS 200 5A61 (PCIE),
    ATI Radeon XPRESS 200M 5A62 (PCIE),
    ATI Radeon X300 (RV370) 5B60 (PCIE),
    ATI Radeon X600 (RV370) 5B62 (PCIE),
    ATI Radeon X550 (RV370) 5B63 (PCIE),
    ATI FireGL V3100 (RV370) 5B64 (PCIE),
    ATI FireMV 2200 PCIE (RV370) 5B65 (PCIE),
    ATI Radeon Mobility 9200 (M9+) 5C61 (AGP),
    ATI Radeon Mobility 9200 (M9+) 5C63 (AGP),
    ATI Mobility Radeon X800 XT (M28) (PCIE),
    ATI Mobility FireGL V5100 (M28) (PCIE),
    ATI Mobility Radeon X800 (M28) (PCIE), ATI Radeon X850 5D4C (PCIE),
    ATI Radeon X850 XT PE (R480) (PCIE),
    ATI Radeon X850 SE (R480) (PCIE), ATI Radeon X850 PRO (R480) (PCIE),
    ATI unknown Radeon / FireGL (R480) 5D50 (PCIE),
    ATI Radeon X850 XT (R480) (PCIE),
    ATI Radeon X800XT (R423) 5D57 (PCIE),
    ATI FireGL V5000 (RV410) (PCIE), ATI Radeon X700 XT (RV410) (PCIE),
    ATI Radeon X700 PRO (RV410) (PCIE),
    ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X700 (RV410) (PCIE),
    ATI Radeon X700 SE (RV410) (PCIE), ATI Radeon X1800,
    ATI Mobility Radeon X1800 XT, ATI Mobility Radeon X1800,
    ATI Mobility FireGL V7200, ATI FireGL V7200, ATI FireGL V5300,
    ATI Mobility FireGL V7100, ATI Radeon X1800, ATI Radeon X1800,
    ATI Radeon X1800, ATI Radeon X1800, ATI Radeon X1800,
    ATI FireGL V7300, ATI FireGL V7350, ATI Radeon X1600, ATI RV505,
    ATI Radeon X1300/X1550, ATI Radeon X1550, ATI M54-GL,
    ATI Mobility Radeon X1400, ATI Radeon X1300/X1550,
    ATI Radeon X1550 64-bit, ATI Mobility Radeon X1300,
    ATI Mobility Radeon X1300, ATI Mobility Radeon X1300,
    ATI Mobility Radeon X1300, ATI Radeon X1300, ATI Radeon X1300,
    ATI RV505, ATI RV505, ATI FireGL V3300, ATI FireGL V3350,
    ATI Radeon X1300, ATI Radeon X1550 64-bit, ATI Radeon X1300/X1550,
    ATI Radeon X1600, ATI Radeon X1300/X1550, ATI Mobility Radeon X1450,
    ATI Radeon X1300/X1550, ATI Mobility Radeon X2300,
    ATI Mobility Radeon X2300, ATI Mobility Radeon X1350,
    ATI Mobility Radeon X1350, ATI Mobility Radeon X1450,
    ATI Radeon X1300, ATI Radeon X1550, ATI Mobility Radeon X1350,
    ATI FireMV 2250, ATI Radeon X1550 64-bit, ATI Radeon X1600,
    ATI Radeon X1650, ATI Radeon X1600, ATI Radeon X1600,
    ATI Mobility FireGL V5200, ATI Mobility Radeon X1600,
    ATI Radeon X1650, ATI Radeon X1650, ATI Radeon X1600,
    ATI Radeon X1300 XT/X1600 Pro, ATI FireGL V3400,
    ATI Mobility FireGL V5250, ATI Mobility Radeon X1700,
    ATI Mobility Radeon X1700 XT, ATI FireGL V5200,
    ATI Mobility Radeon X1700, ATI Radeon X2300HD,
    ATI Mobility Radeon HD 2300, ATI Mobility Radeon HD 2300,
    ATI Radeon X1950, ATI Radeon X1900, ATI Radeon X1950,
    ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
    ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
    ATI Radeon X1900, ATI Radeon X1900, ATI Radeon X1900,
    ATI AMD Stream Processor, ATI Radeon X1900, ATI Radeon X1950,
    ATI RV560, ATI RV560, ATI Mobility Radeon X1900, ATI RV560,
    ATI Radeon X1950 GT, ATI RV570, ATI RV570, ATI FireGL V7400,
    ATI RV560, ATI Radeon X1650, ATI Radeon X1650, ATI RV560,
    ATI Radeon 9100 PRO IGP 7834, ATI Radeon Mobility 9200 IGP 7835,
    ATI Radeon X1200, ATI Radeon X1200, ATI Radeon X1200,
    ATI Radeon X1200, ATI Radeon X1200, ATI RS740, ATI RS740M, ATI RS740,
    ATI RS740M, ATI Radeon HD 2900 XT, ATI Radeon HD 2900 XT,
    ATI Radeon HD 2900 XT, ATI Radeon HD 2900 Pro, ATI Radeon HD 2900 GT,
    ATI FireGL V8650, ATI FireGL V8600, ATI FireGL V7600,
    ATI Radeon 4800 Series, ATI Radeon HD 4870 x2,
    ATI Radeon 4800 Series, ATI Radeon HD 4850 x2,
    ATI FirePro V8750 (FireGL), ATI FirePro V7760 (FireGL),
    ATI Mobility RADEON HD 4850, ATI Mobility RADEON HD 4850 X2,
    ATI Radeon 4800 Series, ATI FirePro RV770, AMD FireStream 9270,
    AMD FireStream 9250, ATI FirePro V8700 (FireGL),
    ATI Mobility RADEON HD 4870, ATI Mobility RADEON M98,
    ATI Radeon 4800 Series, ATI Radeon 4800 Series, ATI FirePro M7750,
    ATI M98, ATI M98, ATI M98, ATI Mobility Radeon HD 4650,
    ATI Radeon RV730 (AGP), ATI Mobility Radeon HD 4670,
    ATI FirePro M5750, ATI Radeon RV730 (AGP),
    ATI RV730XT [Radeon HD 4670], ATI RADEON E4600,
    ATI Radeon HD 4600 Series, ATI RV730 PRO [Radeon HD 4650],
    ATI FirePro V7750 (FireGL), ATI FirePro V5700 (FireGL),
    ATI FirePro V3750 (FireGL), ATI Mobility Radeon HD 4830,
    ATI Mobility Radeon HD 4850, ATI FirePro M7740, ATI RV740,
    ATI Radeon HD 4770, ATI Radeon HD 4700 Series, ATI Radeon HD 4770,
    ATI FirePro M5750, ATI RV610, ATI Radeon HD 2400 XT,
    ATI Radeon HD 2400 Pro, ATI Radeon HD 2400 PRO AGP, ATI FireGL V4000,
    ATI RV610, ATI Radeon HD 2350, ATI Mobility Radeon HD 2400 XT,
    ATI Mobility Radeon HD 2400, ATI RADEON E2400, ATI RV610,
    ATI FireMV 2260, ATI RV670, ATI Radeon HD3870,
    ATI Mobility Radeon HD 3850, ATI Radeon HD3850,
    ATI Mobility Radeon HD 3850 X2, ATI RV670,
    ATI Mobility Radeon HD 3870, ATI Mobility Radeon HD 3870 X2,
    ATI Radeon HD3870 X2, ATI FireGL V7700, ATI Radeon HD3850,
    ATI Radeon HD3690, AMD Firestream 9170, ATI Radeon HD 4550,
    ATI Radeon RV710, ATI Radeon RV710, ATI Radeon HD 4350,
    ATI Mobility Radeon 4300 Series, ATI Mobility Radeon 4500 Series,
    ATI Mobility Radeon 4500 Series, ATI FirePro RG220, ATI RV630,
    ATI Mobility Radeon HD 2600, ATI Mobility Radeon HD 2600 XT,
    ATI Radeon HD 2600 XT AGP, ATI Radeon HD 2600 Pro AGP,
    ATI Radeon HD 2600 XT, ATI Radeon HD 2600 Pro, ATI Gemini RV630,
    ATI Gemini Mobility Radeon HD 2600 XT, ATI FireGL V5600,
    ATI FireGL V3600, ATI Radeon HD 2600 LE,
    ATI Mobility FireGL Graphics Processor, ATI Radeon RV710,
    ATI Radeon HD 3470, ATI Mobility Radeon HD 3430,
    ATI Mobility Radeon HD 3400 Series, ATI Radeon HD 3450,
    ATI Radeon HD 3450, ATI Radeon HD 3430, ATI Radeon HD 3450,
    ATI FirePro V3700, ATI FireMV 2450, ATI FireMV 2260, ATI FireMV 2260,
    ATI Radeon HD 3600 Series, ATI Radeon HD 3650 AGP,
    ATI Radeon HD 3600 PRO, ATI Radeon HD 3600 XT,
    ATI Radeon HD 3600 PRO, ATI Mobility Radeon HD 3650,
    ATI Mobility Radeon HD 3670, ATI Mobility FireGL V5700,
    ATI Mobility FireGL V5725, ATI Radeon HD 3200 Graphics,
    ATI Radeon 3100 Graphics, ATI Radeon HD 3200 Graphics,
    ATI Radeon 3100 Graphics, ATI Radeon HD 3300 Graphics,
    ATI Radeon HD 3200 Graphics, ATI Radeon 3000 Graphics,
    ATI Radeon HD 4200, ATI Radeon 4100, ATI Mobility Radeon HD 4200,
    ATI Mobility Radeon 4100, ATI Radeon HD 4290, ATI Radeon HD 4290,
    CYPRESS, ATI FirePro (FireGL) Graphics Adapter,
    ATI FirePro (FireGL) Graphics Adapter,
    ATI FirePro (FireGL) Graphics Adapter, ATI Radeon HD 5800 Series,
    ATI Radeon HD 5800 Series, ATI Radeon HD 5800 Series,
    ATI Radeon HD 5900 Series, ATI Radeon HD 5900 Series,
    ATI Mobility Radeon HD 5800 Series,
    ATI Mobility Radeon HD 5800 Series,
    ATI FirePro (FireGL) Graphics Adapter,
    ATI FirePro (FireGL) Graphics Adapter,
    ATI Mobility Radeon HD 5800 Series, ATI Radeon HD 5700 Series,
    ATI Radeon HD 5700 Series, ATI Radeon HD 5700 Series,
    ATI Mobility Radeon HD 5000 Series,
    ATI Mobility Radeon HD 5000 Series,
    ATI FirePro (FireGL) Graphics Adapter,
    ATI FirePro (FireGL) Graphics Adapter, ATI Radeon HD 5670,
    ATI Radeon HD 5570, ATI Radeon HD 5500 Series, REDWOOD,
    ATI Mobility Radeon HD 5000 Series,
    ATI Mobility Radeon HD 5000 Series, CEDAR, CEDAR, CEDAR,
    ATI FirePro (FireGL) Graphics Adapter,
    ATI FirePro (FireGL) Graphics Adapter, CEDAR, ATI Radeon HD 5450,
    CEDAR
    (II) VESA: driver for VESA chipsets: vesa
    (II) Primary Device is: PCI 01@00:00:0
    (II) [KMS] drm report modesetting isn't supported.
    (WW) Falling back to old probe method for vesa
    (II) RADEON(0): TOTO SAYS 00000000c0100000
    (II) RADEON(0): MMIO registers at 0x00000000c0100000: size 64KB
    (II) RADEON(0): PCI bus 1 card 0 func 0
    (II) RADEON(0): Creating default Display subsection in Screen section
    "Builtin Default ati Screen 0" for depth/fbbpp 24/32
    (==) RADEON(0): Depth 24, (--) framebuffer bpp 32
    (II) RADEON(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
    (==) RADEON(0): Default visual is TrueColor
    (II) Loading sub module "vgahw"
    (II) LoadModule: "vgahw"
    (II) Loading /usr/lib/xorg/modules/libvgahw.so
    (II) Module vgahw: vendor="X.Org Foundation"
    compiled for 1.7.6, module version = 0.1.0
    ABI class: X.Org Video Driver, version 6.0
    (II) RADEON(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
    (==) RADEON(0): RGB weight 888
    (II) RADEON(0): Using 8 bits per RGB (8 bit DAC)
    (--) RADEON(0): Chipset: "ATI Mobility Radeon X700 (M26) (PCIE)" (ChipID = 0x5653)
    (--) RADEON(0): Linear framebuffer at 0x00000000d0000000
    (II) RADEON(0): PCIE card detected
    (II) Loading sub module "int10"
    (II) LoadModule: "int10"
    (II) Loading /usr/lib/xorg/modules/libint10.so
    (II) Module int10: vendor="X.Org Foundation"
    compiled for 1.7.6, module version = 1.0.0
    ABI class: X.Org Video Driver, version 6.0
    (II) RADEON(0): initializing int10
    (II) RADEON(0): Primary V_BIOS segment is: 0xc000
    (II) RADEON(0): ATOM BIOS detected
    (II) RADEON(0): ATOM BIOS Rom:
    SubsystemVendorID: 0x144d SubsystemID: 0x5653
    IOBaseAddress: 0x3000
    Filename:
    BIOS Bootup Message:
    M26-P Samsung M26 Firenze ATOMBIOS BR14537/rel9.10.1.0/CL199610
    (II) RADEON(0): Framebuffer space used by Firmware (kb): 20
    (II) RADEON(0): Start of VRAM area used by Firmware: 0x7ffb000
    (II) RADEON(0): AtomBIOS requests 20kB of VRAM scratch space
    (II) RADEON(0): AtomBIOS VRAM scratch base: 0x7ffb000
    (II) RADEON(0): Cannot get VRAM scratch space. Allocating in main memory instead
    (II) RADEON(0): Default Engine Clock: 358000
    (II) RADEON(0): Default Memory Clock: 345000
    (II) RADEON(0): Maximum Pixel ClockPLL Frequency Output: 500000
    (II) RADEON(0): Minimum Pixel ClockPLL Frequency Output: 200000
    (II) RADEON(0): Maximum Pixel ClockPLL Frequency Input: 13500
    (II) RADEON(0): Minimum Pixel ClockPLL Frequency Input: 1000
    (II) RADEON(0): Maximum Pixel Clock: 400000
    (II) RADEON(0): Reference Clock: 27000
    drmOpenDevice: node name is /dev/dri/card0
    drmOpenDevice: open result is 10, (OK)
    drmOpenByBusid: Searching for BusID pci:0000:01:00.0
    drmOpenDevice: node name is /dev/dri/card0
    drmOpenDevice: open result is 10, (OK)
    drmOpenByBusid: drmOpenMinor returns 10
    drmOpenByBusid: drmGetBusid reports pci:0000:01:00.0
    (II) RADEON(0): [dri] Found DRI library version 1.3.0 and kernel module version 1.32.0
    (==) RADEON(0): Page Flipping disabled
    (II) RADEON(0): Will try to use DMA for Xv image transfers
    (II) RADEON(0): Generation 2 PCI interface, using max accessible memory
    (II) RADEON(0): Detected total video RAM=131072K, accessible=131072K (PCI BAR=131072K)
    (--) RADEON(0): Mapped VideoRAM: 131072 kByte (128 bit DDR SDRAM)
    (II) RADEON(0): Color tiling enabled by default
    (II) Loading sub module "ddc"
    (II) LoadModule: "ddc"
    (II) Module "ddc" already built-in
    (II) Loading sub module "i2c"
    (II) LoadModule: "i2c"
    (II) Module "i2c" already built-in
    (II) RADEON(0): PLL parameters: rf=2700 rd=7 min=20000 max=50000; xclk=40000
    (WW) RADEON(0): LVDS Info:
    XRes: 1280, YRes: 800, DotClock: 68900
    HBlank: 128, HOverPlus: 21, HSyncWidth: 32
    VBlank: 16, VOverPlus: 4, VSyncWidth: 4
    (II) RADEON(0): Skipping TV-Out
    (II) RADEON(0): TMDS PLL from BIOS: 16500 b0112
    (II) RADEON(0): Skipping Component Video
    (II) RADEON(0): Output VGA-0 has no monitor section
    (II) RADEON(0): I2C bus "VGA-0" initialized.
    (II) RADEON(0): Output LVDS has no monitor section
    (II) RADEON(0): I2C bus "LVDS" initialized.
    (II) RADEON(0): Output DVI-0 has no monitor section
    (II) RADEON(0): I2C bus "DVI-0" initialized.
    (II) RADEON(0): Port0:
    XRANDR name: VGA-0
    Connector: VGA
    CRT1: INTERNAL_DAC1
    DDC reg: 0x60
    (II) RADEON(0): Port1:
    XRANDR name: LVDS
    Connector: LVDS
    LCD1: INTERNAL_LVDS
    DDC reg: 0x1a808
    (II) RADEON(0): Port2:
    XRANDR name: DVI-0
    Connector: DVI-D
    DFP1: INTERNAL_TMDS1
    DDC reg: 0x64
    (II) RADEON(0): I2C device "VGA-0:ddc2" registered at address 0xA0.
    Dac detection success
    (II) RADEON(0): Output: VGA-0, Detected Monitor Type: 0
    finished output detect: 0
    Backtrace:
    0: /usr/bin/X (xorg_backtrace+0x3b) [0x809f7db]
    1: /usr/bin/X (0x8048000+0x54715) [0x809c715]
    2: (vdso) (__kernel_rt_sigreturn+0x0) [0x7785e40c]
    3: /usr/lib/xorg/modules/drivers/radeon_drv.so (0x77226000+0x83208) [0x772a9208]
    4: /usr/lib/xorg/modules/drivers/radeon_drv.so (0x77226000+0x3790c) [0x7725d90c]
    5: /usr/lib/xorg/modules/drivers/radeon_drv.so (0x77226000+0x3988b) [0x7725f88b]
    6: /usr/bin/X (InitOutput+0x5c8) [0x80ab048]
    7: /usr/bin/X (0x8048000+0x1a550) [0x8062550]
    8: /lib/libc.so.6 (__libc_start_main+0xe6) [0x7747db86]
    9: /usr/bin/X (0x8048000+0x1a2f1) [0x80622f1]
    Segmentation fault at address 0x7734f808
    Fatal server error:
    Caught signal 11 (Segmentation fault). Server aborting
    Can anyone help me? Thanks!

    When I install an old xf86-video-ati package from 27.02.2010, everything works. So the problem seems to be the new ati-driver.

  • Creative Zen products and "Frozen" probl

    Hi,
    I'm one of many owners of the zen micro who faces this very problem. I don't really want to caveman it but it seems like creative is intent on not really helping as I don't see a FAQ or an answer to this oh-so-common problem anywhere on the website or doesn't give tech support on products older than 6 months (which is a very short amount of time for an electronic device that costs almost as much as month of my rent). Would you please be so kind as to indicate me the proper technique to fix this?
    Because you see I bought an iPod following the departure of my zen micro and it's been working really well so far but I'd really like to make use of the money I spent previously as a backup player and I don't think it's fair that a problem so common seems to get ignored.
    A brief example, early playstation 2's optic dri've were a major problem, most of them broke in x years/months/days. This was a known problem which anyone using a playstation 2 of that generation would experience at some point. I bought a PS2 second hand which managed to work for 3 years and bam the optic dri've stops working. I call Sony and I get told "mail us the unit, this is known problem and we will fix it for you". Granted it did cost me 5$ to mail the unit, I was very satisfied with Sony's service and now own a PlayStation 3.
    My Creative Zen Micro breaks in a common way and I get told to either smash it hard and have it work for a few more weeks, or I mail it, pay for pieces, repair and mail-cost to have it work for... less than 6 months apparently? I am lost for words, I truly am! Please provide us with a solution because I believe most people using a Creative facing this problem do NOT intend to buy another Creative product.
    Thanks for reading this long text, but I believe it's a fair review of the situation,
    Khanate

    Hey,
    If you tried it on a friend's computer and you're still having problems then it may be a problem with the Zen. Before you call or e-mail tech support, here is what they will tell you do to first before they really get in depth with helping you. Go into Rescue Mode (there is an explanation on how to do this at the top of the forum) and do a disk clean up. After that, try it. If that doesn't work then click the reload OS option which will take the firmware (like windows to your PC) off the Zen. Don't worry you can easily put it back on. Go to Support>Downloads>select Zen Touch, etc, etc. and download the latest firmware and run it. Hopefully that will fix it....
    I had some connection problems myself with my ZT as soon as I got it as well. and simply reflashing the firmware fixed and now I love my Zen. I hope everything works out for you.
    Wilco

  • Creative ZEN TOUCH and Macs, plz h

    Hi,
    I am considering buying a Creative Zen Touch and would like some help
    I was wondering if anyone could answer this for me, and yes, I have the read the FAQ and about Macs and how it isnt officially supported, yada yada
    What I would like to know is, I have a PC at home which I will use to transfer music
    HOWEVER
    At Uni'versity, I am forced to use a Mac computer. What I want to know is, I would like to use the Zen Touch as a portable hard dri've so I can copy my homework (not mp3s, but school work) on to the Zen Touch, then go to Uni'versity, plug in the mp3 player into the Mac and access my DATA files from the Mac WITHOUT having to install any software (i.e. plug n play)
    Thanks,

    peterh85,
    I'm afraid you can't. The player will need driver and application installed in order to link up with the computer for file transfer. Even when MTP firmware is available, you will need to be using Windows XP and Window Media Player 0 to interact with the player.
    Jason

  • Windows XP driver problem - Nomad Zen Xtra and Zen To

    I have both a Nomad Zen Xtra 60GB and a Zen Touch 20GB, both of which were working fine with my Windows XP Pro SP2 computer until a couple of days ago. I had recently put firmware 2.0.03 onto the Zen Xtra, and was using the drag-and-drop method in Windows Explorer to copy loads of albums across to it from my music folder. It seems I might have tried to copy too much over at one go, because eventually the file copying just stopped, and I had to unplug the Zen Xtra from the PC to abandon the copy process. Since then, neither Zen device has been properly recognised by any of my PCs. When I plug the Zen Xtra into?a USB port, Windows brings up the messages: "Found new hardware: Nomad Jukebox Zen Xtra" and "Found new hardware: MTP device", then brings up the Found New Hardware Wizard, even though firmware 2.0.03 is supposed to provide "seamless support with any computer running Microsoft? Windows Media? Player 0 and Windows? XP - no drivers or software needed" (I have WMP0.00.00.4036 installed). The Zen Xtra's display does not show the "docked" icon except when plugged into my laptop (running XP Home Edition)... but even on the laptop Windows still asks for a driver, which it then fails to install properly. When I plug my Zen Touch into my PC, it detects that an MTP device has been connected, but Windows Media Player doesn't list it under the Sync tab, and when I try to install the "Creative Software Suite for PlaysForSure-enabled Creative Zen Touch Players", the installer complains that "Setup could not detect any portable device on your system... please ensure that Zen Touch PlaysForSure Firmware is properly installed". The device's firmware version is 2..0, and as I have already said, both this and the Zen Xtra were working fine with my PC up until a couple of days ago. Additionally, the "docked" icon?no longer appears?on the Zen Touch's display when plugged into the PC. I have made the registry change suggested in Creative Knowledge Base Solution ID #9287, and my PC is up-to-date with Windows Hotfixes. I've also tried uninstalling all Creative programs and reinstalling them one at a time, but I can not get my PC to correctly work with the Zen devices anymore. Any suggestions? Also, is there some kind of Factory Reset that I can do to get my Zen Xtra back to an earlier firmware?

    I had the same issue. My battery ran down during a sync, then I was unable to sync again.
    The Zen is showing up fine in the device manager, but none of the software (Media Player, MediaSource) sees it.
    Finally, after a day of trying new drivers, running cleanup, etc. I decided to go into the Zen's recovery menu. To get there, press and hold the Play button and press and hold the reset (use a paperclip) button while powering up.
    Once there, select the first option in the menu to Clean up the system. I forgot what it's called and I'm in the middle of a sync now, so can't look.
    Worked fine after that. Phew!
    If your device is being detected fine, but cannot sync, try that and post here if it fixes it.
    Tooner
    evokefrank.googlepages.com

  • Develop software for connecting to creative zen touch and other devices not recognized by wind

    hi there,
    as a programmer i wonder, is it possible to obtain information of how to connect to usb-connected creative device (which is not recognized automatically by windows, as the zen touch) and how to communicate with it's is there any documentation about that available to "non-creative" ;-) developers?
    the idea is to create a plugin (e.g. for musikcube) that enables the programm to access the files on the device.
    i know there are third party companies that do provide software for connecting to e.g. zen touch, but i do not think that they have figured out every little bit by themselves, have they?
    greetings and thanks a lot
    asdf

    Try this:
    Download <a href='http://www.delldjsite.com/forums/attachment.php?attachmentid=444' target=_blank>this[/url] file. Extract it to whatever folder you like. Inside that folder run the file fixup.cmd. A DOS window will open up and start display messages on what its doing, when its done it will instruct you to remove the device from Device Manager and reconnect it.
    Try this and see if it works.

  • My new iPhone 5 won't connect to iTunes, and when I connect to my computer it comes up as a usb storage device, also in the phone itself under usage it shows internal memory of 2gb and sd card 64 gb, is this an original iPhone or have I been sold a copy

    My new iphone 5 can not connect to itunes, it comes up as a usb storage device when I plug it in, also in the phone under settings/usage it shows internal memory of 2gb and SD card of 64gb, I cannot get it to connect to itunes at all so cannot sync etc, is this a genuine Iphone or a copy. I have owned 4 iphones and never had a problem with connecting to iphones and restoreing to a backup.

    According to http://en.wikipedia.org/wiki/IPhone_5
    the iPhone5 has 1GB of RAM, and internal storage of 16, 32, or 64GB.
    It does not use SD cards.
    Fake iphones are really Android phones using the skin of iOS6.
    Click on the App Store icon. If it takes you to Apple's App Store, then it's a real iPhone.
    But if you are directed to Google Play, then I'm afraid you've gotten a copy.

  • Adobe Acrobat 7.0.0, ZEN AO and .MSP files

    I'm currently having the following problem...
    I've got two ZEN AO's. One for Adobe Acrobat 7.0 Professional and one for
    Adobe Acrobat 7.0 Standard. I've added the latest Adobe Acrobat 7.0.5 .msp
    (Windows Installer Patch) file to it's respective ZEN AO and incremented the
    AO version number. On my test workstations that are cleanly imaged I
    associate and install either Adobe Acrobat 7.0 ZEN AO and neither object
    applies the 7.0.5 msp during the initial installation of the object/package.
    What gives? I've noticed that during the last part of the installation when
    it looks like it's applying the .msp I see "gibberish" in the text field
    right above the progress bar of the ZEN "Distributing blah blah blah" dialog
    box. I can launch Adobe and verify that the patch has not been applied. I
    can then verify (via NAL in myapps.html) the application and the patch
    applies as expected (I can verify that by launching the application). A new
    install of these objects/packages should include the patch should it not?
    Also if the application was previously installed by this "same" AO (only the
    patch has been added and the version number incremented) and I "install" the
    application (keep in mind it's already installed) NAL / Windows Installer
    goes through the routine of installation and then appears to apply the .msp,
    again I notice the gibberish in the text field right above the progress bar
    of the ZEN "Distributing blah blah blah" dialog box. I can then verify the
    application and the patch applies as expected (again, I can verify that by
    launching the application). What is up with this? I can't believe after
    roughly fifteen agent releases (I say fifteen based on the # of releases on
    the agent release TID) that Novell can't get this basic functionality right.
    Windows 2000 SP4 Update Rollup 1 (including all updates)
    Windows XP SP2 (including all updates)
    Novell Client 4.9 SP1 (including all updates)
    ZEN Agent IR5 and ZEN Agent IR6
    Bryan

    Bryan,
    It appears that in the past few days you have not received a response to your
    posting. That concerns us, and has triggered this automated reply.
    Has your problem been resolved? If not, you might try one of the following options:
    - Do a search of our knowledgebase at http://support.novell.com/search/kb_index.jsp
    - Check all of the other support tools and options available at
    http://support.novell.com.
    - You could also try posting your message again. Make sure it is posted in the
    correct newsgroup. (http://support.novell.com/forums)
    Be sure to read the forum FAQ about what to expect in the way of responses:
    http://support.novell.com/forums/faq_general.html
    If this is a reply to a duplicate posting, please ignore and accept our apologies
    and rest assured we will issue a stern reprimand to our posting bot.
    Good luck!
    Your Novell Product Support Forums Team
    http://support.novell.com/forums/

Maybe you are looking for

  • One TREX server for multiple Portals?

    I have the same requirement as that contained in this thread: TRex for Multiple Portals I wonder if anyone can technically elaborate a bit what the procedure for this configuration. I would have to install a TREX and create a TREX instance for each P

  • How to add hint in a text field

    Hello, How do I add a hint in a text field to let the user know what to type in and the hint will disappear when they click on it?

  • Widget Meltdown

    Widget Meltdown! I did my weekly update for my Mac Mini G4 software from Apple. After the update, most of the Widgets do not fuction properly. Some do not work at all, others do not work if you flip them over, buttons are missing, they scroll off the

  • ICC Profile Version 4 in Photoshop CS3

    I am using photoshop cs3 and printing with onyx rip software. when i export the icc profile for the printer to use in photoshop for soft proofing, it is not showing up. after talking with an onyx rep. they said that the icc profile for the printers a

  • NI-VISA step by step configuration under linux

    Hi! I need to connect and acquire a codebar reader connected to RS232. I have: P4 2.4GHz with PCI6023E, mdk 9.1, LV 6.1 comedi, nicvirte and nivisaserver - nivisa drivers correctly installed and running. Serials RS232 are named ttyS00 and ttyS01 unde