Zen Connection problems (MTP driver install deni

Hi, Whenever I connect my Zen to XP (SP2) I keep getting the popup balloon saying XP has found an MTP device. However, I can't connect to my Zen through any software (explorer, WMP, mediasource etc..). I've tried the above steps in the sticky thread, but nothing has worked.
It's not my player either because it works fine on my brother's computer.
What's interesting is that when I go to the Device Manager and try and update the driver manually ( I can see the Creative Zen drivers). I get an access denied message when I try and tell Windows to update to them. Windows is infuriating like that! Since I've tried installing them through the built in Administrator account.
Another thing is that when I uninstall the drivers via Device Manager then replug my Zen into the computer again, it shows up as a Zen for a split second, then goes back to a generic MTP device. Argh!
I doubt I'll get much help, but if anyone knows or has experienced this before I'd appreciate some help if they've found a way through this!
Thanks.
Edit: My Zen Touch also works flawlessly on this computer which makes things even wierder!
Message Edited by SpaceFarm on -03-200703:3 AM

Similar Messages

JB Zen 2.0 USB Driver install is

Doh!
I did not remember to NOT have my Zen USB 2.0 connected to my system when i did the installs from the CD, and I get a "device driver" install error every time I try to install the drivers, even after un-installing, etc.
Help!
Thanks,
Scott

I installed it on another PC, by installing the software first and then connecting the device, and it was fine.
On the PC in question, when I do connect the device, I do see the device listed in device manager, but it has a ? next to it, and I can never re-install the drivers,because they are in the .exe on the disk. Also, when I plug the device in, XP identifies it as USB, cause I get the ":ding", but Creative Window does not pop up from the system tray, as it does on the other system.
Again, I think the whole issue stems from having the device connected when I installed the software.
I've run thru the uninstall of the app, rebooted, and then even done the "remove programs" from control panel, but still no go.
There has to be somethiing buried in the registery.
I'm an IT professional (but not one of those hacks), but I'm stumped, so I'm turning to the pros.
Now, If I would not have turned off the system restore point utility, I would be ok...
Thanks,
Scott

PXI 8196 connection problem: plugin not installed

Hello NI:
The host PC interacting with our PXI 8196 (1052 chassis) recently had a hard drive failure, and I have had to reinstall all of our LabVIEW software and custom VIs on a new computer. The software is up and running, but I am having problems with connectivity to the PXI. The PXI is recognized in MAX, and everything is accessible (scales for our load cells, etc etc). But when I open up my labview VI project, I cannot connect to the PXI. It has a yellow triangle with an exclamation point next to it, and when I right click, the error message says that the plug-in is not installed. I have one CD that seems to have PXI drivers on it, but after installing, I had the same problem.
I was not the one who originally connected this system, and I am having trouble finding the documentation to get me back up and running. Any help would be greatly appreciated!
Eric
Solved!
Go to Solution.

So I have attached a screenshot from MAX showing all my devices and modules. Through MAX, I am able to access test panels for my modules (like the 6259 DAQ board) as well as the custom scales I have previously set up for the 9 load cells we use. The other screenshot shows where the issue still lies... when opening my LabVIEW project.
When re-installing all the software, I do not remember seeing anything titled "PXI Platform Services". Will all of the MAX connections work without Platform Services? If not, can you direct me to the correct download? We are using Windows XP and LabVIEW 8.2.
Also, I do not see the PXI or anything from NI in the Windows Device Manager. Again, maybe this is because the above Platform Services are not installed?
Thanks for your help!
Eric
Attachments:
PXI MAX screenshot.JPG ‏133 KB
PXI LV project screenshot.JPG ‏53 KB

Connecting problems: software not installed?

Alright, lately I've been having a few problems with my iTunes. At first it wouldn't show up at all, and then when I fixed that, this happened. Whenever I connect my touch to the computer via USB cable, this message appears on my iTunes:
"This iPod cannot be used because the required software is not installed. Run the iTunes installer to remove iTunes, then install iTunes again."
So basically, I can't sync anything from my iTunes into my iPod, it just charges. I have removed and installed it again, doesn't work. Is this some kind of other virus or something else? PLEASE HELP!!

This takes a bit more work than just reinstalling iTunes. You have to do a complete removal of Apple software (see this article: http://support.apple.com/kb/HT1925 ) and re-installation.
The second half of this is make sure Apple Mobile Device Services is running properly after the install. See this article for help/information: http://support.apple.com/kb/TS1567
If Windows doesn't prompt you to reboot after the installations, make sure you do anyway.

Content Server connection problems

SAP Content Server connection problems
I have installed the SAP Content Server on a Windows 2003 server. I connected to the Max DB on the remote server from Database Manager on my PC. I created repositories in R/3 in OAC0 and CSADMIN and saved documents to the Content Server. This all took a few hours from O/S install to saving a document in the repository, so I do understand the basics of the Content Server and Max DB.
Unfortunately we are not going to use Windows; we will be running this on UNIX. Therefore I'm trying it out on a Linux system while I wait for the AIX system to be available. It's been a long road but I have finally gotten the install to finish 'successfully' however I can't connect from R/3.
When I run the check http://10.XXX.YYY.ZZZ:1090/ContentServer/ContentServer.dll?serverInfo from the browser on the Linux host I get back a good status as shown below:
serverType="SAP HTTP Content Server";serverVendorId="SAP AG";serverVersion="640";serverPatch="0";serverBuild="16";pVersion="0046";serverStatus="running";serverDate="2008-03-25";serverTime="22:39:45";startUpDate="2008-03-25";startUpTime="22:32:21";lastAccessDate="2008-03-25";lastAccessTime="22:38:33";
However when I do this from any my PC it won't connect. (Of course the real problem is I can't connect from R/3.)
If I try the same URL from a different user session on the same Content Server Linux host I get the same good status.
I thought maybe the httpd.conf file was wrong so I tried:
Listen 0.0.0.0:1090
In cs.conf I tried commenting out AdminSecurity & AdminSecurityGroup.
I also changed StorageDriver from SAPDBStorage to FSStorage.
I don't know if this is related or just another problem to tackle once I can get through this one. I was not able to add the new system to the Database Manager. I get the error "-4 could not connect to socket [10060]".
Thanks to all for any help. Points will dutifully be rewarded.
David

Hi Henk,
It looks like I am dumber than a rock. The firewall was indeed active on the Linux host. I turned it off and can now do the http connection test to the Content Server. (I awarded very helpful points.)
I still can't connect to the database with the Database Manager however the message has changed; it now says "-4 XSERVER might be inactive". I just turned off the firewall so I have a few things to try, like figure out how to start MaxDB without the DB Manager. I'll post my progress. Thanks Henk.
David
Edited by: Dave Hill on Mar 28, 2008 12:00 AM
Now I have installed the Database Studion on my PC. No I'm getting this message when I try to connect to the host/database on the Linux system: "Cannot connect to host 10.XXX.XXX.XXX:7210 [Connection refused: connect], -813."
Does MaxDB need to be started to connect? Any idea how to start it manually? Thanks,
David
Edited by: Dave Hill on Mar 28, 2008 1:06 AM
Ah, at long last. There's this tiny yet very important little program called x_server that SAP didn't include in the SAP Content Server install guide. This needs to be running in order for anything to connect. I'm sure most of you know about it but for the rest you can find it in:
/sapdb/programs/bin
Then type
./x_server start
I'm not sure what user it should run under but I started it as the sdb user.
You could automate the database startup with a script. See http://maxdb.sap.com/doc/7_7/e9/005dac1592496783e26133eb7fad0b/frameset.htm
Thank you Henk, I'll call this problem solved and award points.
Edited by: Dave Hill on Mar 28, 2008 2:10 AM

All with iTunes connection problem...

If any of you also use the stand alone Yahoo Messenger (the one you download, not the one on their website), are you still able to sign in? I have the iTunes store connection problem, and just installed Yahoo Messenger this afternoon and found that even after creating a new ID, I couldn't log in at all, while I could on Yahoo's website. Installed it on another computer on the same network and it popped right on. Something it blockin both apps from getting a connection or sending log in data, but I don't know what. Be interested to see if anyone else that can't get into iTunes also can't get into Yahoo (or maybe any other IM program).

Yes, there's something in common - a port that got blocked or some other network setting maybe changed by an update or something that's blocking the sending of log in data. The iTunes Store says it's a secure connection - I don't know that Yahoo Log In is done via secure connection or not.
Interestingly, the iTunes network diagnostics lists that it can't connect to any Apple sites at all - even apple.com yet here I am on the same machine using Firefox to type this post on an Apple.com site, so obviously this computer CAN reach Apple.com. I wish I knew an IP or URL to the iTunes Store to try a plain old ping and traceroute outside of iTunes to see if it can be reached from here, but don't know what those would be.

Connection problems with zen to

ok so i have just bought a creative zen touch 40gb used. i installed the software on my computer and tried to connect to put songs on it but the player says docked, my computer recognizes it and yet i cant connect to it using any software. i've tried it on a friends computer with the same results. i've also tried changing cords, changing usb ports, updating the driver, disk clean up on the player, updating usb and mtp drivers as well as deleting and restarting the program. i cant install new firmware since it doesnt see it as connected.
any help at all would be much appreciated as im running out of ideas and patience.
Message Edited by Numenor9 on 08-06-2006 03:8 PM

Numenor9,
So you have already updated to the PlayForSure(MTP) firmware for your Zen Touch player? Take a look at this knowledgebase article SID4763 and follow the ste
ps.
Jason

Zen Micro connection problems with media explorer (my soluti

Hi all,
just wanted to share you my sollution to the connection probs with my Zen Micro. I have installed the MTP version of the firmware and found out it did connected to my machien (media player sync works) however media explorer was not able to install properly (it could not detect the device during install).
I found out that if I closed Acti'vesync (so it is not using the USB probing) it could detect the Zen Micro during install and media explorer installed properly. After this it only detects the zen micro whenever Acti'vesync is not syncing with my PPC or smartphone.
So therefore my sollution to this problem. Make sure Acti'veSync is not connected with a device thorugh USB.

What is "Acti'veSync?" I have installed the firmware and NapsterToGo and WMP recognize my Zen Micro but Zen Explorer does not. Maybe this will work for me. I didn't install CreativeMediaSource.

A connection to the deployment share could not be made - Networking device did not have a driver installed

I have a couple of HP 8200 desktops that I think might have bad nics. When I PXE boot them and start my LiteTouch, I get a Wizard error that says
A connection to the deployment share (\\mydpshare\share) could not be made. The following networking device did not have a driver installed
PCI\VEN_8086&DEV_1502&SUBSYS_1496103C&REV_04
I have that driver in MDT and it works on other HP 8200s. Looking into the Wpeinit.log, it looks like the driver loads but maybe the nic is bad:
Installing device root\kdnic X:\WINDOWS\INF\kdnic.inf succeeded
Installing device pci\ven_8086&dev_1502 X:\WINDOWS\INF\net1ic64.inf succeeded
Spent 16903ms installing network drivers
QueryAdapterStatus: no adapters found
Spent 0ms confirming network initialization; status 0x80004005
WaitForNetworkToInitialize failed; ignoring error
Has anyone seen this before?
Orange County District Attorney

Hi,
According to your description, it should be Intel NIC driver problem. I have checked HP official website, there is new NIC driver released, please access to the link below to download the NIC driver for test:
http://h20566.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5037932&spf_p.tpst=swdMain&spf_p.prp_swdMain=wsrp-navigationalState%3Didx%253D2%257CswItem%253Dvc_111651_1%257CswEnvOID%253D4060%257CitemLocale%253D%257CswLang%253D%257Cmode%253D4%257Caction%253DdriverDocument&javax.portlet.begCacheTok=com.vignette.cachetoken&javax.portlet.endCacheTok=com.vignette.cachetoken
Roger Lu
TechNet Community Support

Re-installing Linksys Connect on laptop after new hard drive installed

I have a E4200 router and had Connect loaded on my laptop. My hard drive crashed and needed replacement. I had no problem signing on to my WiFi once I got the new hard drive installed.
With the new hard drive, I now do not have Linksys Connect installed on my laptop. My question is: Can I re-install Connect with the router running perfectly well or will re-installing Connect with the router already up and running cause me problems?
Thanks for any help.
Solved!
Go to Solution.

Here is an article on setting up the software after the router was already set up.
http://kb.linksys.com/Linksys/ukp.aspx?pid=80&app=vw&vw=1&login=1&json=1&docid=90fabd0b3674497489d42...

Apple Mobile Device USB Driver has a driver problem MTP USB DEVICE ACCESS IS DENIED

I can't do anything i tried to update driver and nothing here is what all it says apple mobile device usb driver has a driver problem MTP usb device access is denied

DON'T DO ANYTHING LISTED BY APPLE SUPPORT.
Just try this -
Start computer in safe mode, go to device manager, locate Iphone, Ipod, or Apple Mobile Device Manager. Update/install driver in safe mode and - voila, successfully installed and no more access denied errors.

MTP driver fails to install on Nokia X6

Hey guys wonder if you could help me out because this forum is simply full of experts!
I know that one of the solutions for installing the MTP driver is to change your usb connection to Mass Storage and delete a folder in the private folder but i can't find it in the private folder! plenty of other folders with lots of digits but no 10208913 folder.
I have just given up and started using WMP in mass storage but it means i can't transfer actual playlists, the songs are transfered but i have to make a playlist manually on my phone which can get real tedious.
if you guys could help that be brilliant and expect plenty of kudos and green box ticking :-)
Solved!
Go to Solution.

Hi,
I have found a work around which has now worked ok for a few months. I say work around because I'm sure this is a Nokia bug not a Windows bug and is thus not solveble entirely without Nokia's intervension.
- To start with get rid of any special drivers you have installed on Windows previously
- Next we need to separated stuff out on the memory card so the files the phone manages are separate from any you add while using at as a USB memory stick.
   -- I decided the easiest way to do this was to start from scratch but there is not need to if you'd prefer not.
- Once ony nokia stuff, music and videos are back on the card pick a single location to use for eveything else. I chose the Others folder.
- Create one or more folder under this location then using the CMD set the attributes of the folders to system, hidden.
    -- i.e. for me:
       --- attrib +s +h "\Others\My Downloads"
       --- attrib +s +h "\Others\My Documents"
- You are all done now.
SO, what are the pros and cons....
Cons:
- No access to personal files with Nokia's built in file manager
- Top level folders are not visible to you in windows so you have to type the path in in the explore address bar.
Pros:
- The phone works as an MTU device!!
- If you lose the phone there is a good chance that your personal files will not be found

I have an Epson printer on a Wifi network. Windows 7 desktop and and HP Win 7 laptop (my wifes) print to it just fine. My MacBook Pro running Yosemite won't detect it, and I have the latest driver installed. No problem when I had a Canon...

I have an Epson printer on a Wifi network. Windows 7 desktop is running the network, and my wife's HP Win 7 laptop prints to it just fine. My MacBook Pro running Yosemite won't detect it, and I do have the latest driver installed. I didn't have a problem when I had a Canon Pixma on the network, but when I replaced it with the Epson nothing seems to work. I go to add a printer to the queue and only the FAX function of the printer shows up - not the WS-4530 print function. Does anyone out there have any suggestions? Please??? :-)

Hi Kelly,
As someone who has to print from my Mac to a networked printer at home all the time, I can certainly understand how frustrating it must be to have that fail to perform as expected. Let's see if we can get you up and running.
I would suggest that you troubleshoot using the steps in this article -
OS X Yosemite: Printing troubleshooting
Start with the section titled Check the network.
Thanks for using Apple Support Communities.
Sincerely,
Brett L

I see that i have a problem after installing my new hard drive on my macbook pro mid 2009 version. I put a new hard drive, with all of my information from my old drive installed on it, into the computer. but now have the blinking question mark folder

i see that i have a problem after installing my new hard drive on my macbook pro mid 2009 version. I put a new hard drive, with all of my information from my old drive installed on it, into the computer. but now have the blinking question mark folder. I see that it means that it isn't reading the new hard drive.
did i miss a step between transferring all of my information from my old hard drive to the new hard drive and installing the new hard drive into the computer. I believe that i installed properly. it was quite easy.
thanks for your help

It means there is no bootable system on the drive. If you still have access to the old drive, then I suggest you boot from it then clone it to the new internal drive. Use OPTION boot to boot from the Recovery HD on the old drive:
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
     1. Select Disk Utility from the main menu then press the Continue
         button.
     2. Select the destination volume from the left side list.
     3. Click on the Restore tab in the DU main window.
     4. Select the destination volume from the left side list and drag it
         to the Destination entry field.
     5. Select the source volume from the left side list and drag it to
         the Source entry field.
     6. Double-check you got it right, then click on the Restore button.
Source means the external old drive. Destination means the new internal drive.

When i connect my iphone to the computer, win 7 i get the mtp driver error (Code 31).

When i connect my iphone to the computer, win 7 i get the mtp driver error (Code 31).
I must mention that connecting the phone and accesing it as a camera worked before but at some point it didn't and i keep recieving this mtp driver error. I tried everything including deleting registry entries, reinstalling multiple times, use the log administrators command in cmd, i don't have a pass on my phone, nothing worked so far. Any help would be apreciated.

Yes I did.. Everything is ready. Just when I plug the cable into the phone and the computer nothing will happen.. When I plug it into our "business" laptop immediately it will show that it is connected... With this laptop I am using now, nothing happens..

Zen Connection problems (MTP driver install deni

Similar Messages

Maybe you are looking for