Zen Micro with PC connection Problems and no firmw

I'm running on Windows XP Service Pack 2 and I have Windows Media Player 0.
...and my Zen Micro wouldn't be detected, so I formatted it completely and I tried reloading the firmware. My old Zen Micro with v firmware still connects perfectly well, but Windows just doesn't detect my v2 firmware (now no firmware) Zen Micro.
Advice, please?
:edit:
Windows DOES detect my Zen Micro now...but I still can't do anything with it. It appears as MTP player connected:
http://i3.photobucket.com/albums/y52/bkblade/zen.jpgMessage Edited by bkBlade on 04-25-2006 2:4 AM

bkBlade,
Check this Knowledgebase article SID0053 and make sure the USB registry entry is correct. If you do make changes to the registry base on the Knowledgebase info, then try reloading the v2 firmware again.
Jason

Similar Messages

IPod nano with computer connection problems and more

My iPod Nano is always stuck at 1:06am and on the completely wrong date. The time will not change. If I try to change the date and time, it freezes up and I have to do a hard reset so I can get it to function. This problem it has had for quite a while now, and I don't view as a very pressing issue.
The following problem however is new to just yesterday. It impedes me from updating the iPod or adding new music. I added new music to it a month or so ago and yesterday was the first time I have tried to do anything with it on a computer in 2014.
It will not connect to a computer. The moment I try to chord it up, my entire computer runs slower, and iTunes crashes. My computer also doesn't always recognize that it is plugged into the it even though the iPod will have a "Do not disconnect" screen and is charging.
Another interesting thing to note is that I have tried to synch my iPod up to a few different computers and the results are the same, and if you try to shut down or boot up a computer with my iPod attached to it, it won't. It'll stop mid process and refuse to shut down or boot up.
I have followed some of the troubleshooting guides on similar sounding problems to no avail.
I realize that my iPod is also fairly old as far as iPods go (2008) and I will probably have to just get a new mp3 player. However, I would like to avoid that outcome as long as possible.

first off , i don't think there should be any issues updating the router's firmware on a vista machine....
the other things that you can try are :
changing the MTU size to 1365 ,
under the "advanced wireless settings" subtab, change the beacon interval - 50 , fragmentation and RTS threshold - 2304 ...

Help: Problem using Zen Micro with Yahoo Unlimited Music Serv

I get a "Error reading device contents: The Data is Invalid" message when I try to synchronize my Zen Micro with the Yahoo music engine. When I first connect my Zen via usb, the Yahoo engine recognizes the Zen Micro but it is unable to read the contents of the Zen prior to my synchronizing. After trying to read my Zen for a while, I get the pop up message described above. I am using version 2..02 zen firmware and version .0..4 of the Yahoo engine.
Has anyone experienced this problem before? Does the Zen Micro actually work with the Yahoo service?
Thanks

Here is the Internet address for one of the forums for Yahoo Music Engine. You might find some possible solutions here.
http://grou 
 
 
p.../yme-feedback/
Best wishes.
luvmyrescuedogs
Message Edited by luvmyrescuedogs on 08-0-2005 07:46 PM

Problem with creating Connection pool and JNDI, driver is not detected

Hi,
I have an issue with creating Connection Pool and JNDI.
I'm using:
- JDK 1.6
- OS: Linux(ubuntu 8.10)
- Netbeans IDE 6.5.1
- Java EE 5.0
- Apache Tomcat 6.0.18 Its lib directory contains all necessary jar files for Oracle database driver
- Oracle 11g Enterprise
My problem is that the Oracle database driver is not detected when I want to create a pool (it works pretty well and is detected without any problem when I create ordinary connection by DriverManager)
Therefore after running:
InitialContext ic = new InitialContext();
Context context = (Context)ic.lookup("java:comp/env");
DataSource dataSource = (DataSource)context.lookup("jdbc/oracle11g");
Connection connection = dataSource.getConnection();and right after dataSource.getConnection() I have the following exception:
org.apache.tomcat.dbcp.dbcp.SQLNestedException: Cannot load JDBC driver class 'oracle.jdbc.OracleDriver'
at org.apache.tomcat.dbcp.dbcp.BasicDataSource.createDataSource(BasicDataSource.java:1136)
at org.apache.tomcat.dbcp.dbcp.BasicDataSource.getConnection(BasicDataSource.java:880)
at servlets.Servlet1.doPost(Servlet1.java:47)
at servlets.Servlet1.doGet(Servlet1.java:29)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:617)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:717)
at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:290)
at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206)
at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:233)
at org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:191)
at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:128)
at org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:102)
at org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineValve.java:109)
at org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:286)
at org.apache.coyote.http11.Http11Processor.process(Http11Processor.java:845)
at org.apache.coyote.http11.Http11Protocol$Http11ConnectionHandler.process(Http11Protocol.java:583)
at org.apache.tomcat.util.net.JIoEndpoint$Worker.run(JIoEndpoint.java:447)
at java.lang.Thread.run(Thread.java:619)
Caused by: java.lang.ClassNotFoundException: oracle.jdbc.OracleDriver
at java.net.URLClassLoader$1.run(URLClassLoader.java:200)
at java.security.AccessController.doPrivileged(Native Method)
at java.net.URLClassLoader.findClass(URLClassLoader.java:188)
at sun.misc.Launcher$ExtClassLoader.findClass(Launcher.java:229)
at java.lang.ClassLoader.loadClass(ClassLoader.java:307)
at java.lang.ClassLoader.loadClass(ClassLoader.java:252)
at java.lang.ClassLoader.loadClassInternal(ClassLoader.java:320)
at java.lang.Class.forName0(Native Method)
at java.lang.Class.forName(Class.java:169)
at org.apache.tomcat.dbcp.dbcp.BasicDataSource.createDataSource(BasicDataSource.java:1130)
... 17 more
My application context file (context.xml) is:
<?xml version="1.0" encoding="UTF-8"?>
<Context path="/WebApplication3">
<Resource auth="Container"
 driverClassName="oracle.jdbc.OracleDriver"
 maxActive="8"
 maxIdle="4"
 name="jdbc/oracle11g"
 username="scott"
 password="tiger"
 type="javax.sql.DataSource"
 url="jdbc:oracle:thin:@localhost:1521:database01" />
</Context>and my web.xml is:
 <resource-ref>
 <description>Oracle Datasource example</description>
 <res-ref-name>jdbc/oracle11g</res-ref-name>
 <res-type>javax.sql.DataSource</res-type>
 <res-auth>Container</res-auth>
 </resource-ref>
...I found similar threads in different forums including sun, such as
http://forums.sun.com/thread.jspa?threadID=567630&start=0&tstart=0
http://forums.sun.com/thread.jspa?threadID=639243&tstart=0
http://forums.sun.com/thread.jspa?threadID=5312178&tstart=0
, but no solution.
As many suggest, I also tried to put context directly in the server.xml (instead of my application context) and referencing it by <ResourceLink /> inside my application context but it didn't work and instead it gave me the following message:
org.apache.tomcat.dbcp.dbcp.SQLNestedException: Cannot create JDBC driver of class ' ' for connect URL 'null'
Has anyone succeeded in creating a connection pool with JNDI by using Tomcat 6 or higher ? If yes, could kindly explain about the applied method.
Regards,

Hello again,
Finally I managed to run my application also with Tomcat 6.0.18. There was only two lines that had to be modified
in the context.xml file (the context of my application project and not server's)
Instead of writing
<Context antiJARLocking="true" path="/WebApplication2">
 type="javax.sql.DataSource"
 factory="org.apache.tomcat.dbcp.dbcp.BasicDataSourceFactory"
</Context>we had to write:
<Context antiJARLocking="true" path="/WebApplication2">
 type="oracle.jdbc.pool.OracleDataSource"
 factory="oracle.jdbc.pool.OracleDataSourceFactory"
</Context>- No modification was needed to be done at server level (niether server.xml nor server context.xml)
- I just added the ojdbc6.jar in $CATALINA_HOME/lib (I didn't even need to add it in WEB-INF/lib of my project)
- The servlet used to do the test was the same that I presented in my precedent post.
For those who have encountered my problem and are interested in the format of the web.xml and context.xml
with Tomcat 6.0, you can find them below:
Oracle server: Oracle 11g Enterprise
Tomcat server version: 6.0.18
Oracle driver: ojdbc.jar
IDE: Netbeans 6.5.1
The context.xml file of the web application
<?xml version="1.0" encoding="UTF-8"?>
<Context antiJARLocking="true" path="/WebApplication2">
 <Resource name="jdbc/oracle11g"
 type="oracle.jdbc.pool.OracleDataSource"
 factory="oracle.jdbc.pool.OracleDataSourceFactory"
 url="jdbc:oracle:thin:@localhost:1521:database01"
 driverClassName="oracle.jdbc.OracleDriver"
 userName="scott"
 password="tiger"
 auth="Container"
 maxActive="100"
 maxIdle="30"
 maxWait="10000"
 logAbandoned="true"
 removeAbandoned="true"
 removeAbandonedTimeout="60" />
</Context>The web.xml of my web application
<?xml version="1.0" encoding="UTF-8"?>
<web-app version="2.5" xmlns="http://java.sun.com/xml/ns/javaee" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://java.sun.com/xml/ns/javaee http://java.sun.com/xml/ns/javaee/web-app_2_5.xsd">
 <resource-ref>
 <description>Oracle Database 11g DataSource</description>
 <res-type>oracle.jdbc.pool.OracleDataSource</res-type>
 <res-auth>Container</res-auth>
 <res-ref-name>jdbc/oracle11g</res-ref-name>
 </resource-ref>
 <servlet>
 <servlet-name>Servlet1</servlet-name>
 <servlet-class>servlets.Servlet1</servlet-class>
 </servlet>
 <servlet-mapping>
 <servlet-name>Servlet1</servlet-name>
 <url-pattern>/Servlet1</url-pattern>
 </servlet-mapping>
 <session-config>
 <session-timeout>
 30
 </session-timeout>
 </session-config>
 <welcome-file-list>
 <welcome-file>index.jsp</welcome-file>
 </welcome-file-list>
</web-app>Ok, now I'm happy as the original problem is completely solved
Regards

ZEN Micro won't turn Off and now won't turn

Hi Everyone, hope you can help me out here.
I have been using my ZEN micro for about week now and it was at first working fine.
Then it started not turning off, so i had to pull out the battery.
This is obviously very annoying, but it got worse over time.
It now won't turn on unless i switch it about 30-40 times.
What is going on, is there a way to fix it and is anyone experiencing the same problem?
Thanks very much,
Fern

FernIe, I have the exact same problem, although now my Zen Micro won't turn on at all via the switch.
My Zen Micro is 5 months old and its only been over the past few weeks I've been having problems. It started with having to hold the switch in the power on position for a least 30 secs and trying it at least 5-0 times before the player would turn on, and having to remove the battery to turn it off. Now, not matter how many times I try the switch or how long i hold it for, the player won't turn on.
The battery is fully charged and I have never had problems with the headphone jack, and I haven't dropped it or done any damage to it that I think could be causing it. I'm having to turn it on by plugging it into my computer through the USB cable and then unlpugging it once its on, it's a pain doing this and means if I want to use it later I have to keep it on, muted, in my bag all day with the lock turned on (that end of the switch works) then once its turned off I can't turn it on again until I get near a computer again.
I've searched the discussions and knowledge base but haven't found an answer. I've just emailed the support team and I'm waiting for their response, would be interested to know what they've told you.
Just letting you know your not alone and I feel your pain!
Jen

Playlist in zen micro with playsforsure firmw

I'm using a zen micro with the 2..02 firmware... and napster to go... napster to go takes forever to transfer my tracks so usually I just use WMP 0 as a standalone... The question is... why can't I view playlists that I created on the fly inside my player in WMP0.... I've already accepted the fact that you can't delete most of the mandatory Napster playlists without deleting the tracks that they are composed of... and that kinda sux... but I thought that you would at least be able to view the playlists that you created on your player in WMP 0.... Is there something that I'm not doing?

WMP0 does not handle playlists properly, well not at all, so it will not work with any device the way its intended to do. Just got to sit back and wait for the next WMP update that Microsoft releases, but this problem was posted on their KnowledgeBase since March I believe so they are well aware of it.....

Have a Zen Micro (6GB) - Lost Software CD and Firmware update confuses me. Please he

I bought my Zen Micro about 7 months ago and have been using it fine until recently formatted my computer and realized I've lost my software cd (the one that comes with the player).
I tried downloading the Creative MediaSource Organizer/Player (version 3.30.2) and updating the firmware (thereby loosing all the songs I had saved in there. Ugh.) in my Zen Player and in the beginning MediaSource still wouldn't pick up my Creative Player. Then, I don't know why, it now works...but it works like a normal External HardDri've or a PenDi've would! It not longer has that menu thing (where there's a list of artist and albums) at the left side but simply folders under the Creative Player.
Does anyone know where I can get the old firmware and download the required software? I greatly prefer the way my player worked before I updated the firmware/software and I would like to just have that back even if it doesn't have as much features or whatever came with the upgrade. (iTunes or something. Has no idea what that is.)
Also, does Creative have a Service Center in Malaysia (specifically Kuala Lumpur) and can anyone tell me where it is or give me the phone number to call? I'm still under my warranty but this site doesn't list a number to call although they say they give Telephone Support until the warranty expires.
Thanks in advance for any help!
Cherish
Edit: BTW, I have tried emailing Customer Support but so far, no reply, and that was...2 weeks ago, I think? And, like I said, the Customer Support section in this site doesn't list any numbers/Service Centers which is why I'm asking...Message Edited by cherish90 on 02-06-200705:25 PM
Edit the second: Does anyone know if the confirmation email that Creative is supposed to send to your account after you send them an email isn't working? Because I just double checked my inbox and I realized I never got any confirmation letter. And I'm very sure I didn't accidentally delete it.Message Edited by cherish90 on 02-06-200707:38 PM

LOL. I've sent in my player. FINALLY found the Service Center (for those in KL who want to know, it's in Berjaya Amoda, behind Low Yat and opposite Times Square) after asking the shop I bought the player from.
And the guy who I talked to called their HQ or whatever and said that neither of the messages I sent (I sent 2; one shortly after I started this thread) were recorded/received on their end although I DID get the "Your message has been sent" page after clicking on the 'submit' button. And yeah, I used this email too. *confused* Maybe Creative doesn't work with Mozilla Firefox (the browser I'm using)? I think that's kind of lame, though, because FireFox is like practically as big as EI now and it's more user-friendly (the tabs are uber cool IMHO). Unless Creative has some sort of problem with Mozilla...
*cough*
ANYWAY...
Yeah, I did download the PlayForSure plugin (although I have no idea what it's for) and MediaSource STILL picked up my Micro as something like a pendri've.
Never mind, though. The guy I talked to - never got his name... - said that once you've upgraded the firmware to the latest (which is the one that needs all these weird plugins and makes the device an MTP [I THINK that's what it's called] device) you can't change the firmware back to the old one unless they send it in. So I'm sending it in. And I think they'll replace the software CD for me too, so that's all good.
Thanks anyway, Jason.
Cherish

Unending connectivity problems -- and Desktop Help...

I'm wasting so much time on connectivity problems that it's positively wearying. Prior to the installation of BT Infinity here in April, I had a low quality broadband service because of the length of the line from the exchange: if I could get a download speed of 1.2Mbps and an upload of a quarter of that, I was doing well.
BT advised that thanks to fibre optic, my Internet should run much faster. So we had Infinity installed. I'm registered with Speedtest.net so am able to see my performance record.
The average download speed is now aroun d 6Mbps and the average upload, more than that at 7Mbps. How an upload speed can consistently be faster than a download escapes me.
But I'm not familiar with the ways of Internet connectivity and try as a I might, can't get my head around it.
This desktop computer runs Vista OS. Vista was **bleep** when it came out and is renowned for its botched handling of Internet connections. So I'm not blaming BT for the literally unending connectivity problems that are occurring now, with line drops, speeds slowing to a crawl, and no guarantee that any connection will last. But it would be good to actually use BT software to help fathom out what's going wrong here, and today's typical morning which looks like this:
1) Boot up computer. Automatic connection to hub via Netgear USB wireless adapter. Hub is on ground floor of this 3-storey property but signal strength from hub is excellent, as confirmed by inSSIDer monitoring, currently showing 54 with no other networks anywhere near that figure.
2) Perhaps 5 minutes after connection established, it's then lost. 'Local Only' is displayed. This is, apparently, a known Vista problem. But Microsoft has issued a fix for it. I know this, because it took 100 hours of ploughin g the Net to find out that MS had finally admitted to one more Vista screw-up. I've used the Microsoft router "fix it" before and it didn't work ("failed to process") so uninstalled it and have DL'd it again now and run it. This time it says it has fixed everything.
3) Computer is re-booted to make the fix effective. Computer connects to Internet. Speedtest.net check yet again confirms that upload speed is faster than download speed.
4) Connection dies. So much for Microsoft Fix It.
5) Windows diagnostics reports that it can re-set the IP profile (or something.) I click yes. The re-set goes through. Connectivity is restored. 10 minutes later, connectivity is lost. Just a red X in the tray. No connection of any kind, not even that daft 'Local Connection' only alert.
6) Reboot. Yet again. BT Desktop Help was installed here and ran OK when we were using our Netgear DSG34 router. But since the change to the BT Hub, the BT program has never run at all. So-oo. . . It has been uninstalled. And then re-DL'd and re-installed. And though the installation has been completed, clicking on 'launch' has failed to launch anything. But anyway. An hour ago, in one of the brief periods today when the Internet connection was holding up, I Revo-ed out the earlier install, DL'd BT desktop Help and re-installed it. . . and I'm still at the same stage as always, with a Firefox browser page that's open and completely blank and has been for the past 30 minutes. The URL is:
file:///C:/Program%20Files/BT%20Broadband%20Desktop%20Help/btbb/Start.html
Repeated page re-loading gets nowhere. Malwarebytes PRO is turned OFF to prevent any possibility of blocking and the antivirus is termporaily SUSPENDED. This PC runs on Windows standard firewall but even turning that OFF doesn't get the page to load. Copying the address into Internet Explorer in case there's a Firefox problem merely results in Firefox being opened and the same blank page running there.
7) After all that. . . Connection lost yet again and this time, Windows cannot connect at all. It reports that the "wireless network security key is not correct". I happen to know that it is, because this is maybe the 20th time it has reported this in the past 10 days and every time I have to key in the "correct" key all over again. . . at which point Windows still says it isn't correct and cannot repair.
Turning off the computer completely, unplugging from the wall, holding in the power switch for a full minute to clear the circuits, traipsing up and dowen three flights of stairs to turn off the hub, then wait, then turn the power back onm again. . . Ah, wot fun times I'm having here with my particular versioin of Infinity (as in, an infinity of connectivcity problems.)
Summary: I seem to be being simultaneously hit with one issue after another.
I'm bewildered as to why ever since Infinity was installed here, my upload speed is generally faster than my download speed. I'm not happy with endless Internet connection failures though am thinking that Vista is playing a large part here with its "wrong security key" and unending 'Local Only / Limited Connection' failures. I do miss my Netgear router and the ability to access a fantastic help menu and re-boot directly from the desktop without having to keep going up and down three flights of sdtairs to do so (I haven't been able to find out how toe access the BT Hub remotely.)
Above all though: I'm really tired of repeatedly trying to run freshly downloaded and installed BT Desktop Help software but getting no further than a blank page because the program has stalled.
If anyone has any advice / suggestions, other than to buy a carrier pigeon, that'd be much appreciated.
Thanks.

Thanks again to John and gg30340. Here's an update:
1) BT Desktop Help removed completely from this computer. The uninstaller itself mopped up everything, which surprised me. But anyway.
2) Bt Home Hub manager set up and working. Had to input serial number and create new password. All of this sounds fairly easy and would be if one had the device near the desk. But the idiots who built this property shoved the BT master socket inside the garage next to the door. Our two home computers are on the third floor. To ensure the wireless signal strength is OK, the Hub and Infinity module/device/whatever it's called are on a high shelf. It's a major job to even reach the darn things, never mind read the labels seeing as how the BT Infinity engineer was good enough to tidy up the cabling and make a very tight connection to the wall socket.
3) I had hoped to be able to back up the Hub's settings, seeing as the software provides for Advanced Settings / System / Backup. But not on mine (Hub 3.0). All that System allows is choosing which internet clock to define the accurate time. Everything else in System is just a pattern of short lines as if trying to indicate that there's some text there but it's invisible.This is now my second encounter with BT software which, for whatever reason, isn't functioning as it should on this PC.
4) Hub reset to factory fresh, according to BT guide.
5) Reset appears to have achieved nothing apart from requiring the password to be popped in again. After reset, it wasn't even possible to connect to the hub manager. Internet connectivity was eventually established for all of 30 seconds and then, gone.
6) Computer was shut down and then booted anew. Internet connectivity is still. . . dreadful. One minute everything's fine and then, literally,. the next minute a webpage won't load. Even opening the Hub Manager has taken three attempts, i.e., disconnecting from the Internet, re-connecting, failing, and trying twice more until success. Yet all the time these failures are occurring, the tray icon is showing a steady, unwavering green icon for Local and Internet access -- despite the fact, there manifestly isn't any.
7) Speedtest. net tests are actually showing upload and download 'trajectories' going slower and slower and finally halting at some point on the arc, then after a period of up to 30 seconds, suddenly becoming animated again. Speed test results with broadband speed checker UK and Think Broadband's checker are so at variance with one another, and with Speedtest, net, that it seems all three are using different technologies in pursuit of the same thing. Either way, upload speeds continue to be much, much faster than download speeds, a state of affairs I certainly have never encountered before.
8) Speedtest net tests taken in the past 10 minutes, with one test following on from its predecessor, begin at 8.24 down/8.88 up, followed by 5.24 down / 6.40 up, followed by a mind-numbingly lonnnnng 0.62 down / 8.70 up -- in other words, a continuous yo-yoin g of Internet connectivity to the pooint that it actually might as well not even be here (I've had to make five attempts just to get on to this forum. . .)
9) BT Speedtest will necessitate disconnection of everything downstairs and all boxes being lugged up here. This is actually going to require uncoililng tied-off cabling and hanging off a stepladder to do so -- though I surely can't be the only person in Britain who doesn't have a nice, handy BT master socket in their study or lounge. That said though: until we switched to Infinity, we *never* experienced these kinds of horrendous connectivity problems and never had need to unplug the Netgear router downstairs and bring it upstairs to connect directly to tjhe desktop PC so BT's own test could be run.
I'll just have to get to work dismantling stuff tomorrow. However, I have to say that after a factory re-set which has changed nothing at all, I'm beginning to think there's a problem with the BT line itself (hence why I'm happy to follow the advice here, though less than happy at the prospect of the messing about involved.)
Thanks, you two, for your patient help, and also for clarifying the situation re the three signal paths being shown on inSSIDer. At least I know that's usual now! And now, hopefully, when I press 'Post', I won't be faced with an endlessly spinning Firefox circle culminating in what may well be, or seem to be, the 57,938th time today of seeing "Page Not Found". . .

TS1538 my ipad can not continue to download ios 6.1.2 because of connection problem and it is stuck in connect to itunes image, i cant open it anymore..what should i do? help plz

my ipad can not continue to download ios 6.1.2 because of connection problem and it is stuck in connect to itunes image, i cant open it anymore..what should i do? help plz

Connect to iTunes on the computer you usually Sync with and “ Restore “...
http://support.apple.com/kb/HT1414
If necessary Place the Device into Recovery mode...
http://support.apple.com/kb/ht4097
You may need to try this More than Once...
Be sure to Follow ALL the Steps...
But... if the Device has been Modified... this will Not necessarily work.

N95 8BG "WiFi Connection problems" and "Web: no ga...

Like many users, I could not get my new Nokia (N95 8GB) to work with my WiFi. After many attempts, using the various ideas posted, I came up with a solution that works reliably for me.
First lets deal with "WiFi Connection problems"
Menu/Tools/Settings/Connection/Wireless LAN
'Show WLAN availability' = 'Yes'
'Scan for networks' = 'Every 5 minutes'
Some users have suggested choosing 'Advanced Settings' from the 'Options' menu, changing 'Automatic configuration' to 'Disabled' and the either setting 'RTS threshold' to '2346', or setting 'Power saving' to 'Disabled'. I tried both of these but they did not make any difference in my case. However they may make a difference for you, hence their inclusion here.
Menu/Tools/Settings/Connection/Access Points
Choose 'New access point' from the 'Options' menu
'Data bearer' = 'Wireless LAN'
'WLAN network name' = If your network is set to broadcast its SSID, use 'Search for networks' then select your network from the list, otherwise use 'Enter manually' and type in the SSID.
'Connection name' = anything you like, but I use the SSID
'Network status' = not sure about this maybe someone can confirm, but I think if the SSID is broadcast then it is 'public', otherwise it is 'private'.
'WLAN network mode' = match this to your access point configuration. Mine is set to 'Infrastructure', so I do not cover the ad-hoc scenario here.
'WLAN security mode' = again I am using WEP so have not covered other scenarios.
'WLAN security settings' = these should match you access point configuration.
'Homepage' = whatever you like. I use 'http://www.google.co.uk', just so that when I start browsing I get something reliable, useful, and dependable. If Google fails to appear it usually means there is something wrong with your config.
Now lets handle the dreaded "Web: no gateway reply"
Menu/Tools/Settings/Connection/Access Points
Scroll down to highlight the new access point and choose 'Edit' from the 'Options' menu. Now choose 'Advanced settings' from the 'Options' menu.
Assuming you network used IPv4, which most do in my experience, select 'IPv4 settings'. I don't know about IPv6, and don't use a proxy so these are not covered.
The values you enter in 'IPv4 settings', depend upon your network/router settings, and whether you have a DHCP server or not.
Assume your a router IP Address, on the LAN side, is 192.168.0.1, and that it has a DHCP server set to serve addresses in the range 192.168.0.64 to 192.168.0.192, using subnet 255,255,255,0. Since the mobile does not seem able to get an IP Address from the DHCP server we give it a static address 192.168.0.55. Notice this is outside the range sereved by te DHCP server to avoid conflicts.
We end up with:
'Phone IP address = '192.168.0.55'
'Subnet mask' = '255,255,255,0'
'Default gateway' = '192.168.0.1'
'DNS address' = 'user defined'
'Primary DNS address' = '192.168.0.1'
'Secondary DNS address' = '0.0.0.0'
I used something similar and was at last able to browse the web via wifi.
I hope all of the above helps someone out there.

I have just experienced this problem having been using the WiFi network for months without problems. I tries all the suggestions on these forums including the power settings, turning off WEP, and the fixed IP suggestion and none worked. I even reinstalled the firmware and reconfigured everything. It turned out to be the router. I had rebooted it several times to no effect but the DHCP always gave the N95 the same IP address lease. So I changed the range of IP addresses the DHCP could lease and restarted the N95. It got a new IP and was back working again.
If at first you don't succeed, try again. Then quit. There's no use being a damn fool about it.
-- W.C. Fields

Zen Micro with iTu

Hi, is someone can tell if i can use zen micro with iTunes and how do it ? thanks

brotsalami wrote:
as far as i know the itunes agent will not work with the micro. but i don?t know for sure.
It definately works with my wifes MuVo Micro N200. I think it supports all players that has a USB removable dri've feature, so it should work fine with the Micro.

Any possibility to record on a ZEN micro with an external m

hi!
is there any possibility to record on a ZEN micro. with an external mic?
i searched the web and found "things" like that for e.g. the ipod working by the usb port of the palyer.
tia

it would act as if the drive is a built-in DVD burner.
http://www.flickr.com/photos/60081959@N04/7717521136/
Here is what a Lenovo Slim USB portable DVD Burner looks like under iTunes on my X220T
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

My Imac 27' screen is shutting off for no reason. The Imac is still running but the screen is black and stay like that. Is there anyone else with the same problem, and does somebody know what is this?

I had my Imac27' for about 1 year (I bought it january 2011) , and it worked fine. But two days ago a problem started. The screen is turning black suddently, and it stay like that until I reboot it. It's not cool. The first time it happen it was hafter a very long days of video editing, I tought it was to hot. But now I just started up the Imac and 10 minutes later it happen. And now I transfer my desktop on my second screen, because the one of my Imac is constantly shutting of. What is this? Can I do something about that?

I´ve came across with the same problem and when I look out for solutions I found out that basically I had Three options
1.- Dim the brightness to the first 2 dots (that is the limit for me, anything above that shuts down again my screen)
2.- Replace an expensive part of the screen (about $900)
3.- Try with an external monitor to see if the problem was the screen or something else
What I did was to plug my flat screen to my mac with a Mini Display Port to VGA Adapter
http://store.apple.com/us/product/MB572Z/B/mini-displayport-to-vga-adapter?fnode =51
And… Problem Solved! now Im going to buy a Monitor that gonna cost me less than half of the replacement parts, my main monitor will keep siting down if i dim it above the 2 dots but at least I will have the other to work properly
So that´s that, I hope someone finds this helpful
P.S. Sorry if my english it´s not that good

All with iTunes connection problem...

If any of you also use the stand alone Yahoo Messenger (the one you download, not the one on their website), are you still able to sign in? I have the iTunes store connection problem, and just installed Yahoo Messenger this afternoon and found that even after creating a new ID, I couldn't log in at all, while I could on Yahoo's website. Installed it on another computer on the same network and it popped right on. Something it blockin both apps from getting a connection or sending log in data, but I don't know what. Be interested to see if anyone else that can't get into iTunes also can't get into Yahoo (or maybe any other IM program).

Yes, there's something in common - a port that got blocked or some other network setting maybe changed by an update or something that's blocking the sending of log in data. The iTunes Store says it's a secure connection - I don't know that Yahoo Log In is done via secure connection or not.
Interestingly, the iTunes network diagnostics lists that it can't connect to any Apple sites at all - even apple.com yet here I am on the same machine using Firefox to type this post on an Apple.com site, so obviously this computer CAN reach Apple.com. I wish I knew an IP or URL to the iTunes Store to try a plain old ping and traceroute outside of iTunes to see if it can be reached from here, but don't know what those would be.

Zen Micro "not connected" problem since upgrading firmw

Hi All,
I have had the zen micro for a week and it has been working fine with original firmware & software supplied on CD.
After noticing the battery life was poor, I decided to upgrade the firmware.
This is where all my troubles began...
After upgrading the firmware to 2.00.2 I found that when I connected my player it was now recognised at an MTP device and windows asks me if I would like WMP (windows media player) to sync with the device.
If I select yes, it tries to find the device in WMP and tells me it is not connected !
If I go into Control Panel- Device Manager tells me that I DO have a zen micro connected under the "Windows Media Devices" section.
Zens micro media explorer now also fails to see my device and thinks it is disconnected.
So I have no way of transferring files to my zen micro.
In an attempt to remove the problem I try going into rescue mode on the zen and reloading the firmware to an earlier version, with a version I have downloaded from this website .0.03.
The zen successfully erases the firmware and behold, my pc still fails to recognise the device so it cannot install any firmware on top of this.
So now I have a Zen with no firmware installed (and a "firmware problem" message everytime I turn it on) and a pc that won't recognise it anymore.
I have spent a good 5 hours this evening trying to fix this.
I have tried everything on these forums, but I simply cannot get my PC to connect to the zen micro, despite it recognising it everytime I connect it !
Please help before me or the zen dies !
Thanks,
Mat.

Here is a note I sent to the Creative support folks. They simply suggested I go back to firmware .0.03.
I have to admit, going back to the other firmware update does not seem to be the true resolution, but I really don't have any more time to waste fixing your bugs. So, I am now on .0.03. It's a good thing I synchronized all 920+ songs, or I would not be a happy camper right now. :-)
I will tell you it appears to be a multiple USB issue with your new firmware. I experimented with this, and found that if I have my iPAQ connected into my USB ports, as well as my USB mouse, my USB CD/DVD dri've and my USB Keyboard, the MTP explorer will not recognize the Zen Micro.
When I take the iPAQ out, magically, the Zen Micro gets recognized and the MTP Explorer is working. THIS ONLY HAPPENS WITH THE MTP FIRMWARE!!
I am now back to the .0.03 release of the firmware and none if this happens. As I write this to you, I have everything connected and I am ripping a CD to my device - no problems. I am fortunate however to have a laptop that I was able to do this with, otherwise I would be in the same place others are, and the upgrade frimware doesn't ever recognize the Zen Micro, even though it is in the Device Manager. ?
So, I would say, that your MTP firmware takes control too much, and seems to substitute for something like an iPAQ, where they cannot co-exist or other USB harware, such as a memory reader (CF, SmartMemory, etc.). This is not a PC USB issue, in my mind. It is a firmware issue that is causing the conflict.
Thanks.

Zen Micro with PC connection Problems and no firmw

Similar Messages

Maybe you are looking for