Zen MicroPhoto will not STOP charg

Recently my MicroPhoto will not stop charging. I had it plugged in for a long time and it wasn't done charging yet and I thought for sure it had to be because it was charging for a few hours and the battery was only about 50% used. So I unplugged it and plugged it back in and the power chord icon appeared on the battery which means that it's fully charged when a few seconds earlier it said it was still charging. I hope someone can help me because I know over charging a battery is about the worst thing you can do to a battery. Please help. Thanks

Thanks snoweagle
It worked! I either wasn't letting it charge enough or I wasn't letting the battery get low enough. I let it charge with the AC adapter, and when I went to check on it, it had stopped charging and turned off.
Thanks again I love my ZMP!

Similar Messages

  • ZEN Microphoto will not sta

    I have a Zen Microphoto that freezes at the Creative logo on start up.
    I have tried recovery mode but it will not do anything e.g. reload firmware, format etc. Also it is not recognised by the PC allthough it does charge from the USB when battery is completely flat.
    Anybody know how to fix this?
    Or can anybody tell me how to get it repaired by Creative?
    Thanks

    I can help..
    I've repaired about 5 Microphotos. When you can't boot beyond the initial Creative screen, it's the hard drive that's died. Don't quote me, but Creative quoted me something like $5 to replace the HD. Not really worth it IMHO. I've been buying the Microphotos on eBay for about $0 each, and there's a vendor on eBay that sells new 8 gig HDs for about $45 FOB Taiwan or something like that. Taking the Microphotos apart is a bit tricky, you can snap one of the connectors off the PC boards when you pull the unit apart. It happened to the first unit I opened, and happened once more when I pulled the 0th one apart or so.
    If you want, email me at [email protected] I have a few parts and such including a new hard dri've left over from all of the ones I bought. Now that I have 7 working 8 gig units, I don't need any more.. I can either repair it for you or send you a hard dri've. Contact Creative though first in case the quoted price by me above is inaccurate.

  • My centro will not stop trying to hotsync

    So today my phone will not stop hotsyncing i can't even use the phone unless it is connected to the usb charger
    Post relates to: Centro (Sprint)

    Remove the battery and leave it out for an hour. Place the device 2-4 feet away from mild heat source. (A lamp etc etc)
    This problem is sometimes caused by water damage, allowing the unit to dry out might take care of it. Otherwise check the bottum connection for debris and consider hard reseting the unit. If the problem continues post that then the unit will need to be repaired or replaced.
    Post relates to: None

  • After upgrading to IOS 8.1 the activity icon on the status bar will not stop rotating. Any suggestions?

    AAfter upgrading to IOS 8.1, the activity icon on the status bar will not stop rotating. It's like the webpage never completely downloads. Any suggestions?

    Nginear48 wrote:
    Thanks for your quick response. I've tried everything you suggested and get only temporary fixes. Sometimes for a day or two, sometimes only until I use Safari for the first time. It's annoying and probably effects battery life between charges.
    You would think that it must have some effect on the battery, but oddly enough, the update to iOS 8 actually helped my battery life, in spite of all of these hinky little issues that are taking place. In my experience, the activity icon is not affecting the battery in a negative way.
    Another issue with IOS 8.1 that you may have seen is the loss of icon pictures on home pages. Again it seems to be Safari related, since app icons found in the App Store are not affected, only web based icons you personally put on home pages. I get what I call a test screen similar to what you used to get on old tv sets on every one of my personal icons.
    I know exactly what you mean. I got that as well. On a few of them, when I opened the websites using the generic test screen icons and then closed them, they changed back to the way that they should look. For the ones that did not change, I recreated the home screen shortcuts and deleted the generic looking ones - the test screen icons.
    And don't get me started on iBooks.
    For the very limited use that I make of the iBooks app, i haven't noticed any problems, but I rarely use the app. I don't read books on the iPad other than a few user guides and if they are pdf guides, they reside in more reliable and feature rich pdf apps on my iOS device.
    I wish that I had the fix for the spinning activity icon, but everything that I try, is temporary at best. IMO, this is the buggiest iOS update that I have seen, and I have been using iOS devices since iOS 3 on my first iPad. I realize that there are plenty of people that are not experiencing issues, but I have seen a number of weird things that I wish I could fix. None of my problems are major, but they are annoying.

  • I updated to ios 7 and now the battery does not stop charging any ideas, or have to wait for update? thanks

    i updated to ios 7 and now the battery does not stop charging any ideas, or have to wait for update? thanks

    To show the battery percentage used go to settings
    from there click general scroll to usage and select
    scroll to bottom of page for battery usage select on.
    This will show the icon battery and the percent numbers on the top right.
    When phone is connected to an outlet sometimes it does not always show complete charge. I do not understand why but it is what it is.
    FYI I sent reply to you not to deggie. You can have your own satisfaction to reply direct.

  • Rebuilding aMacBook 1.83 GHz Intel Core Duo, hard drive failure so rebuilding system.  Aircard will not stop self-assigning IP address.  Any ideas how to resolve successfully?

    Had hard drive failure on MacBook 1.83 GHz Intel Core Duo, so had to rebuild the OS on new drive. Was on Lion 10.7.5 prior to failure, but had to reinstall Snow Leopard 10.6.3 since that was most recent OS on media I had.  After finally getting ethernet connection to router working, was able to get to internet and download / upgrade to 10.6.8.  I assume I can probably buy the upgrade to Mountain Lion 10.8 from there.
    Problem is this, Airport will not stop self-assigning IP address for my wireless connection, and unless I can get wireless back on this laptop, doesn't make a lot of sense to continue the rebuild and reinstall of all the software that was on it prior to HD failure.  Only way to my home network and router is ethernet now.  Everything else on my network (Apple MacBook Pro laptops, iPhones, desktops, and non-Apple printers and laptops) is hooking up to router wirelessly fine.
    Any ideas how to resolve successfully so that the airport will stop self-assigning and allow the router to assign the IP address?

    When see the beachball cursor, note the exact time: hour, minute, second.  
    These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
    Launch the Console application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad and start typing the name.
    The title of the Console window should be All Messages. If it isn't, select
              SYSTEM LOG QUERIES ▹ All Messages
    from the log list on the left. If you don't see that list, select
              View ▹ Show Log List
    from the menu bar at the top of the screen.
    Each message in the log begins with the date and time when it was entered. Scroll back to the time you noted above.
    Select the messages entered from then until the end of the episode, or until they start to repeat, whichever comes first.
    Copy the messages to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
    The log contains a vast amount of information, almost all of it useless for solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
    Please don't indiscriminately dump thousands of lines from the log into this discussion.
    Please don't post screenshots of log messages—post the text.
    Some private information, such as your name, may appear in the log. Anonymize before posting.

  • Creative Zen Vision M not fully charging

    (Creative Zen Vision M not fully charging( Hi, I recently bought a refurbished ZVM that doesnt seem to charging properly. When I first got it, it hadnt been charged in quite some time so the battery was overdead. My PC couldnt detect it when I connected it via usb and it didnt even start charging at all. I then connected it to a wall charger and it finally started charging. The strange thing is it never fully charges. I've charged it twice now, both times for at least about 2 hours, and the battery doesnt go more than 50%. And when I connect it to my PC to transfer songs, instead of resuming its charge, my battery runs out. Is this a case of a faulty battery? I li've in Australia and I bought it from the USA. I would prefer not to go through the trouble of returning it if I could. Anything I should do like leaving it to charge for an even longer time? Also one more thing I should mention. When I remove the wall charger and plug it back in, it takes the ZVM sometime to detect it, about 30 minutes or so, and start charging again. Any help or suggestions would be greatly appreciated.

    I have the exact same problem. I just mailed mine in for repair today.

  • My ipod touch will not stop playing music

    My ipod touch will not stop playing music. I will pause the music, leave the playlist, and after 30-60 seconds, the music starts playing again. I use my ipod when I run and when I drive (hook it up to the stereo). It is very annoying when I stop to take a phone call or listen to directions, turn off my music, and then hardly a minute into my stop, the music starts right back up again.

    FUEL1996, not correct. Apple does not allow one app to control another app.
    laurathecellist
    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Unsync all music and resync
    - Reset all settings      
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:                                 
    iOS: How to back up                                                                
    - Restore to factory settings/new iOS device.             
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
      Apple Retail Store - Genius Bar              

  • My ipod shuffle will connect to itunes on computer but will not fully charge and will not play songs

    My Ipod shuffle was washed in a washing machine but dried completely. Now it will connect to my itunes on my computer but will not completely charge or play songs. Can anyone tell me if this is a lost cause and I should buy a new one or is there hope that I can fix this.

    Moisture will cause short circuits, so the battery is being affected.  The audio output is also affected.  You really can't tell if it is completely dry, on the inside.  So, it's possible the current condition will improve if it is left alone to dry out for while longer.  It is also possible that moisture (and short circuits) caused permanent damage.
    Since it is recognized in iTunes, you can try doing a Restore (from the shuffle's Summary or Settings tab).
    There is nothing else you can do (actively) to fix it, so if you want to have a usable shuffle now, you'll need to get a new one.  You can leave this one alone for a month or so (in a dry well-ventilated location), and try it again.  If it works, you'll have a new shuffle and a backup.

  • Itunes 10 will not stop auto syncing

    I have itunes 10 on a mac and a 160 gb ipod classic.
    it will not stop auto syncing when I plug in my ipod, even though "do not auto Sync" button is checked as well as checking off "do not open itunes automatically.
    It syncs FOREVER. I would love to find a way to stop this from happening. I dread plugging in my ipod to put on new music etc.

    I have had this problem with Windows 7 and iTunes updates for some time. Each time it takes hours to solve but with the over the air upgrade to IOS6 on my iPhone and iPad, I was determined to solve and remember what I did, So here it is:
    http://www.care4pcs.co.uk/2012/09/pear-shaped-apple-ios-6-for-iphone-ipad.html
    I hope this helps you and any other users.

  • My data wheel will not stop spinning (i think i am being tapped)

    iphone 3GS 3.1.3 16gb white not jailbroken completly stock
    ok every time i open up my native phone app the data wheel instantly starts spinning and will not stop. it does stop as soon as i close it.
    i thought it might have something to do with google sync so i deleted my mail account but it did not help aat all
    PLease help this is driving my crazy

    Perhaps it's trying to access your voicemail. Is that working properly? Does the Phone app work?
    Try resetting your iPhone by pressing the home and sleep buttons until you see the Apple logo, ignoring the slider. Takes about 5-15 secs of button holding and you won't lose any data or settings.

  • ITunes will not stop verifying

    I have an iPhone4 with the latest iTunes (10.1.0.54) and when I plug my iPhone4 in, it will not stop verifying. I used to have this problem if I canceled a sync. It would verify the phone the next time I plugged it in. I did that this time. I canceled a sync, but now it will not stop verifying to do anything else. I have left it plugged in for 14 hours and it just verifies the entire time. I can do nothing else. It is not set to sync automatically. How do I stop this?

    I'm having the same problem, but I've got a MacBook Pro (rather than a PC).
    Not only does it continue to 'verify' but it won't even let me force quit (says it's restoring my phone ... but after a number of hours it must be done already).

  • Whenever I open Firefox a series of sirens start and will not stop. Does not happen in Internert Explorer.

    When Firefox is opened a series of sirens starts and will not stop until Firefox is closed.
    == This happened ==
    Every time Firefox opened
    == started when I opened a news story from the Sacramento Bee News Paper on line. ==
    == User Agent ==
    Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; GTB6.4; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729; InfoPath.1)

    That is an issue with the "Cool Previews" extension.
    See [tiki-view_forum_thread.php?locale=en-US&comments_parentId=678288&forumId=1]

  • My Ipod 4g will not stay charged. He charges it to show full battery

    My sons Ipod 4g will not stay charged.  He charges it to show full battery & will only work for 20 mins or so.  I have tried resetting the whole Ipod, we have tried a wall charger instead of computer charger, he has removed items off thinking they were to much for the Ipod. Nothing works.....

    If you successfully  (went through all steps without errors) restored the iPod to factory settings/new iPod and still have the problem that indicates a hardware problem. An appointment at the Genius Bar of an Apple store is in order.

  • Ever since I upgraded to 4.0, the welcome tab will not stop opening. It's getting rather annoying.

    The welcome tab for the new 4.0 will not stop opening every time I open my browser. Each time I open Firefox two tabs open, the welcome page for the new 4.0 and my home page. I updated some time ago and this welcome page is becoming quite annoying. How do I stop it from opening? In the past, it has stopped after the first time I open Firefox following an update.

    Thank you for the reply. I have Google set as my homepage, and that's the only homepage listed in the Options box. I tried restoring to default, but when I opened again, the 4.0 page and Google opened again. That leads me to think it might be options, but that article meant absolutely nothing to me.
    What I find strange is that when I have one Firefox window open, then open another Firefox window, only the Google page opens, not the "get to know 4.0" page.

Maybe you are looking for

  • Do I need a new optical drive?

    My CD/DVD drive stopped working a few weeks ago.  It is recognized by Windows but discs are not recognized. My system: dv6-1350us Windows 7 Home Premium x64 optical drive:  CDDVDW TS-L633M What I have already done: Uninstalled and re-installed the dr

  • Need information on licensing in OBIEE 10g

    Experts , Can you guide me on how licensing works in OBIEE 10g ? Scenario : If there is one license for a PROD box for 1 Project ,then can other team use that PROD box. Is there any document on Licensing . Appreciate your help . Thanks, Anand

  • Error the entered value does not match the specified field type

    Hi, When I try to insert a null value to a field of the User Defined Table I am getting the error "The entered value does not match the specified field type" in SAP Business One version 2007 PL 42. Any help would be appreciated. Thanks in advance. Su

  • Call when not null

    Hi, I have a system which works fine but one part is not working. The user has the option to enter text into a comments box and when the user clicks submit an email should be sent if the comments box is not null, but at the minute an email is sent wh

  • Error: The property attribute must be specified

    Hi,     When I am using Flex's validator I get the error specified below Error: The property attribute must be specified when the source attribute is specified.     at mx.validators::Validator/getValueFromSource()[C:\autobuild\3.2.0\frameworks\projec