Zip drive in MDD

Now I'm trying to make use of some parts of my newly abandoned G3 B&W. One thing that's in there is a Zip drive (100MB). Is it possible to install this in my "new" G4 MDD 1.25GHz? There is a SuperDrive in there already.
Thanks.

The zip drive is recognized but not the super drive.
That sounds like the jumper issue I mentioned to the original poster. The ATA bus that serves the optical drive(s) requires little jumpers on the back of each drive be moved about to set priorities on that cable. You cannot have two masters or two slaves, only one master one slave. Unless it's been altered, your optical drive should already be set to "master."
This Iomega install document (a small pdf) shows how to set the jumpers on the back of the ZIP:
http://download.iomega.com/english/manuals/english/en325401.pdf
It's on page 5.
Typical cabling suggests that the master device be at the end and the slve device use the mid-cable connector.

Similar Messages

  • Replacing the zip drive with the dvd-ram

    I've replaced the built in DVD-RAM with DVD burner.
    I have a zip drive too. Can I to replace the zip drive with the DVD-RAM?
    Thanks

    Hi, mikmik -
    Unless your G4 is a G4 MDD model, doing that is not easy at all.
    The bay for the Zip drive on all G4's earlier than an MDD model is considerably smaller than a standard drive bay, which is what an optical drive needs.
    Open your case and take a look at the relative sizes of the upper optical drive bay and the lower Zip drive bay.
    In order to put replace the Zip drive with an optical drive you would need to do a fair amount of surgery on the frame. It has been done; here's a pictorial step-by-step by one fellow who did that to a B&W G3 -
    http://www.shanescot.com/photos/BW_mod/
    The work needed on a G4 would be very similar to that.

  • Installed Lion OS 10.7.2 and now Zip Drive 100 will not open

    Using iMac Intel in only Apple mode. Zip Drive 100 connected to USB
    Thank you for your replies to my Zip Drive question. I too cannot understand what happened. Up until I upgraded to Lion OS 10.7.2, I was able to use  my 100 Zip Drive. Now it will not open any of these Zip disks. The Zip takes the disk, green light goes on but it never registers on the desktop nor opens up

    Up until I upgraded to Lion OS 10.7.2, I was able to use  my 100 Zip Drive.
    But what were you running before you upgraded? I'd say your problem is that you don't have any Zip Drivers that are compatible with Mac OS X 10.7. If they even exist, you'd find them on the Iomega site. But the last ones they have are for 10.3 and 10.4, so that doesn't bode well for any support.
    If I were you, I'd post a question in the Iomega Support forums about this problem and whether or not (and how) you can get your Zip drive to work on 10.7.
    http://www.iomegasupportforums.com/phpbb2/index.php

  • How can two users work on iMovie?  My husband is working on a memorial video for a family member who passed, I plan to edit but he had to take his computer to work.  I have the iMovie project on a zip drive.  How do I get it to open in my imovie?

    How can two users work on iMovie?  My husband is working on a memorial video for a family member who passed, I plan to edit but he had to take his computer to work.  I have the iMovie project on a zip drive.  How do I get it to open in my imovie? 

    You will need an external drive that is formatted as MAC OS EXTENDED (journaled).
    Move the Project, Events, and any photos and music to the external drive by following the instructions in this post.
    https://discussions.apple.com/docs/DOC-4141
    Be sure to use CONSOLIDATE MEDIA to get the photos and music. Then plug this drive into your computer and you will be able to edit.

  • Computer no longer sees DVD or Zip drives

    Hey there all,
    Here's one for you. I have a G4 Gigabit Ethernet that I've upgraded with a Powerlogix 1.4 Ghz processor and an ATI Radeon 9800 Pro. The two drives that came with the computer (the Zip 100 and the DVD-ROM) have stopped working. I can't pinpoint exactly when because for a while I used them only rarely. I do know that they worked after upgrading the chip and I've only just now upgraded the graphics card so I don't think either of those have affected them.
    They are still getting power because the light on the Zip comes on at startup (and will sometimes stay on for a loooooooong time though it doesn't make noise and there is no disk inside) and the DVD drive will still open and close. However, neither drive will mount when a disk of any sort is inserted.
    I've tried running System Profiler and they don't show up in the lists there either. I checked the ribbon and power cords internally and all the connections SEEM ok. I even just now tried hitting the Cuda button to reset things but that turned up bupkiss.
    Any ideas? Any advice? Anyone ever dealt with this before? I 've been shopping around for new drives but before I lay out the cash for that I want to make sure that these aren't saveable. This computer has been an absolute rock for about 6 years and has never had any major problems that I couldn't resolve so I'd hopefully not have to replace it.
    Thanks all for your time and consideration, I'd really appreciate any and all help you can offer. Cheers!
    G4 Gigabit Ethernet Desktop and 15" G4 Laptop   Mac OS X (10.4.9)   Mac OS X 10.3.9 on laptop

    Hi, RaptorRed67 -
    Does the fact that the Zip drive read light comes on at startup and stays on for minutes to hours afterwards bear any clues?
    That light is intended to serve as a diesk-being-read indicator. If it stays steady on, that usually means the Zip drive has somehow managed to hang, and needs to be reset. It can also indicate a non-readable disk is lodged inside.
    The way to address a disk hung inside is to restart, then immediately press the mouse button, keep it held down for a while. This is a hardware instruction to the Mac to eject all removable media, and operates before any drive has tried to load a disk which may be present.
    If the drive itself has hung, which can happen after a non-mountable disk has been ejected, the only way to reset it is to power it off. This means shutting the Mac down - a restart won't do it.
    Since you've unplugged that drive, the Mac was probably powered down when you did that. This would indicate there may be something else wrong with the drive, if it is in fact the culprit.
    The two drives, optical and Zip, need to be jumpered correctly in order for both to function, just like hard drives. The optical drive should be jumpered as Master, the Zip drive as Slave. It is possible that a jumper fell off.
    There may also be something wrong with the controller that serves the bus shared by the two drives. Don't know how to test for that other than to take the machine to an AASP.

  • Booting from a zip drive

    Is this possible. If so anyone want to tell me how to?

    sk8,
    There are two ways to boot a Zip disk on the Lombard:
    - Use the third-party VST Zip100 media bay drive; you can find used drives on eBay and probably some Mac-oriented sellers of used hardware.
    - Use a SCSI Zip drive and the same regarding used drives. You will need an HDI-30 connector for the powerbook's SCSI port.
    The Lombard does not support USB booting...this feature was added to the Pismo and only for 9.x.
    You can also find VST and MCE media bay HDs that will boot the Lombard.

  • How do I download firefox to a disc (or zip drive) and transfer it to another pc (one without a browser)?

    I updated firefox to the newest version and it wouldn't work (something about the proxy server) so I stupidly tried to fix it by using the restore program. I then realized that the old firefox was uninstalled when I downloaded the new updated version and now I have no way to get on the internet at home. Some very nice people told me I could download firefox to a disc or zip drive and then install it on my computer at home. I couldn't save the stupid thing, it just installed itself on the computer. I know this is a ridiculous request, but could someone please, please, please give me a step by step? It would really be appreciated.

    Lindsey, go to the web page that cor-el refers to in his/her reply. You will find a grid with all of the different languages that FF comes in.
    Select "english (US)" and click on the "download" link for your operating system. You will go to another page where it states that your download will begin automatically.
    You should then see a message box come up and ask if you want to save the file. Click on "Save File" and save it to whatever device you are using to transfer it to the other PC.
    Take the device with the file and plug it into the other computer. Using "My Computer," navigate to the device and double-click on the file. It will then start the FF installation process. Follow the on-screen directions from there. The file is about 8.2Mb so allow yourself enough space on your device.
    I hope this little note will get you where you want to go, but remember; "No matter where you go............there you are."

  • Iomega usb zip drive not mounting to desk top

    i have a external usb iomega 250 zip drive and i can seem to get it to mount to the desk top
    i look on iomega website and it says that OS X dose not need any software install or additional drivers to work
    i cant seem to get it to mount on the desk top
    i have also installed the software from the disk and it wont mount
    i them uninstall the software and try it again and still the same problem
    as i know that this is a old beast of a drive system i am trying to get some songs off this disk from a 4 track zip disc recorder
    any help would be great
    thanks santini

    santini,
    This article may help:
    http://support.apple.com/kb/HT1720?viewlocale=en_US
    Please remember there is no Iomega icon on the desktop until you mount a 250MB disk, just like the optical drive.

  • Can I use a ZIP drive with my LCII?

    Can I just plug in a SCSI ZIP drive in my pizza-box and get it working? I can use it with mac OS 6 or 7, I need to exchange and storage files.
    Something like this : http://cgi.ebay.it/IOMEGA-ZIP-100MB-EXTERNAL-SCSI-DRIVE-MAC-PC-AOK-WARANTY-/1305 26545470?pt=PCC_Drives_Storage_Internal&hash=item1e63fd063e#ht_1239wt_1141
    Thank you!

    Do you need to store the files on Zip disks or could you use an external SCSI hard drive?  The reason I ask is that Zip drives, while very useful and convenient, had some production problems and/or a design flaw (depending on one's point of view) for a while.  The problem was named after the symptom that it caused - "Click of Death" or "Death Click."  You'd insert a disk into the drive and hear the heads click down to find the control track, then after a few moments, the heads would release, then click down again, then release, etc.  While the drive was still powered ON and trapped in this endless cycle, you couldn't eject the disk with the Mac OS "Put Away" command or by pressing the manual eject button.  Whether it was an alignment problem or not, the disks became damaged.  I don't think that Iomega ever compiled a definitive serial number range for affected units, so there's really no way to determine whether or not a used unit will develop the problem at some point.  I bought an internal SCSI Zip drive about 6 years ago at eBay and it developed the problem within a couple of weeks.  Fortunately, the seller sent me a replacement and didn't require return shipping of the bad drive.  You could be lucky and get a drive that has had little usage and delivers trouble-free performance for as long as you need it.  As for using the Zip drive with your LC II, you may need to download an older version of the IomegaWare software from Iomega's web site, to be compatible with the Mac OS you're running - especially if it's System 6.  I've never used a Zip drive with anything older than 7.5, possibly 7.1 on my LC III - I can't remember since I soon upgraded the LC III to OS 7.6.1.  With the Iomega software on a floppy disk, you can run the "Iomega Guest" program, that enables use of the Zip drive without installing the software on the hard drive.  Otherwise, installing the IomegaWare software on the hard drive would be most beneficial to you.

  • Can i install system 7 on a zip drive?

    Hi
    I own a Mac plus and i'd like to connect it to the internet. I had a look at a few web browsers, like MacWWW "Samba" but it isn't great. I'd like to try out MacWeb, but it requires system 7. It appears I need to install system 7 on a hard disk to do so. Problem is, I don't have any SCSI hard disk... and they are quite expensive on ebay. So I was wondering, is it possible to install it on a zip drive? They are quite inexpensive and I already have zip disks at home.
    I've never hooked one up to a "classic" Mac, so I hope the os recognises it as a drive and not as a floppy. If not, I'm afraid this won't work...
    Thanks,
    Bad Gold Eagle
    PS: My Mac has 1Mb of RAM, I've got a copy of 7.1. Is 1Mb enough for the early version of MacWeb (1.1.1E)?

    Hello,
    A Zip drive can be connected to a Macintosh Plus. The following web page has further information about this:
    http://www.vintagemacworld.com/pluszip.html
    System 7 requires at least 2 MB of RAM. In order to connect a 68000 processor machine to the Internet, you should really have the maximum amount of RAM, though (in this case 4 MB).
    An older Internet FAQ could possibly be of interest to you:
    http://www.knubbelmac.de/spiegel/mac-internet-faq-2002-12.html
    You may also need access to another appropriate approx. 1991-1997 Macintosh computer (with a floppy drive for both 800K and 1.44 MB) to be used as an intermediary for software downloads.
    System 7.1 came on 1.44 MB floppy disks, which cannot be used directly on a Macintosh Plus. A full US System 7.0 on 800K floppy disk images contained in a larger self-mounting image (.smi) is available for download from Apple:
    http://www.info.apple.com/support/oldersoftwarelist.html
    http://download.info.apple.com/Apple_Support_Area/Apple_Software_Updates/English -North_American/Macintosh/System/Older_System/System_7.0.x/System_7.0.smi.bin
    Jan

  • Adding a new Hard Drive in the Zip Drive Bay

    Today, I was looking inside my power mac 466 Digital Audio, and I realized that it appeared that a third hard drive could fit into the Zip Drive bay. I has a spare HD and Zip drive lying around, and I realized that they are the same height and width. I know that they use the same connectors (on some dells, the zip drive is plugged in with the HD 2 connector), so is it possible to connect a third hard drive in the Zip bay. In the powermac manual, apple doesn't say that you can, but is it possible, and if it is possible, is it harmful to the computer?

    Those particular PowerMacs have two IDE controllers with master/slave setups. One IDE controller is for the optical and Zip drives and the other is for hard drives. You can have two IDE hard drives on the double sled in the back of the PowerMac. You can have a single hard drive each on the middle and front sleds also, but you'll need a separate PCI controller for those drives. That would give you four hard drives without doing anything contrary to Apple's original design. You can put a pair of 120GB IDE hard drives on the double sled and built in IDE controller in the back and then put a pair of 1.5TB SATA drives on the middle and front sleds hooked to a PCI SATA controller. If you need more than that you've still got FireWire and Gigabit Ethernet external storage... What are you doing that needs that much storage anyway? Can't you just burn stuff to CD or DVD and get it off your hard drive(s)? I do video encoding for a TV network and I really don't use much hard drive space. I burn my finished work onto CD or DVD and then delete it off my hard drives.

  • How to transfer photo files from Iomega Zip Drive cassette to my iMac?

    1 GHz PowerPC G4
    768 MB DDR SDRAM
    external hard disk 500 GB
    external hard disk 125 GB
    Many years ago I stored/copied my photos onto a Iomega Zip Drive cassette. Subsequently I lost everything in a computer malfunction which Apple Store could not fix; they ultimately replaced my computer. The computer that I was using when I used the Iomega Zip Drive was a Mac Quadra, not an iMac. Unfortunately, I had not backed up anything so the only thing that I have from the time prior to the malfunction is what I have stored on these Zip Drive cassettes and on the hard drive of the iMac that malfunctioned and was replaced with a new iMac. The photos that I really want to get are those of my husband who has since passed away.
    It has been so long that I used them or even looked at them that now I don't know how to get those photos onto my present iMac (and I am assuming that it is possible).
    Would you be so kind as to tell me what to do to transfer my photos from the Iomega Zip Drive cassette? Thank you very much.
    — Lorna in Southern California
    http://web.mac.com/lorna6
    17" flatscreen iMac, 1 GHz Power PC G4, 768 MB DDR SDRAM   Mac OS X (10.4.7)   LaCie external hard drive, 111 Gigabytes, iPhoto 6.0.4, Canoscan scanner

    Lorna, I'm sorry to hear of your loss. 
    The easiest thing to do is to purchase an External USB Zip drive (link). As ZIP disks are now legacy technology ebay has a great many available which means they are pretty low cost. Simply connect the drive and insert the disk. The disk will mount on to the desktop.
    Alternatively you could see if a local Internet café still has such as drive available and they will be able to burn the contents to CD for a few dollars.
    Hope that helps.
    mrtotes

  • How do I download a movie from my zip drive

    I have a movie my husband got for me from his work, how do I get it from my zip drive to my I tunes movie section, and how do I get my home video in the home vidieo section?

    Yes but
    Can it not be connected to a Mac
    Old SCSI - to old Mac as a G3-PowerMac
    Then files copied over to a FireWire or USB hard disk
    (If file is less than 4Gb DOS/FAT32/Mac Exchange formatted - will still work)
    If file is > 4Gb then open it on a PC and Export it in - less than 4Gb blocks and as streamingDV or AIC.
    These files can then be assembled in iMovie (up to HD6) or FinalCut (any version) and will keep 100% Quality.
    As more You tell - as more we can help
    Yours Bengt W

  • AUDIO SAMPLES FROM IOMEGA 100 ZIP DRIVE TO MAC BOOK PRO / LOGIC?

    Posted: Fri, Feb 15 2013, 1:27pm    Post subject: AUDIO SAMPLES FROM ZIP 100 TO MACBOOK PRO / LOGIC?
    HI THERE
    I HAVE LOADS OF OLD AUDIO SAMPLES ON ZIP DISKS ( ZIP 100 using akai cd3000 sampler ) THAT I WOULD LIKE TO TRANSFER TO MY MAC BOOK PRO FOR LOGIC EX24.
    IS IT A SIMPLE CASE OF A 'SCSI TO USB LEAD' , WILL MY MAC BOOK PICK IT UP FROM THERE OR DO I NEED SOFTWARE OR DRIVERS FOR MY MAC TO BE ABLE TO SEE THEM?
    IS IT EVEN POSSIBLE AT ALL?
    THANKS

    Hi guys
    Sorry for the delay in coming back. I bought a zip drive pretty cheaply then and it has only just turned up. However when I put my old ZIP disks in, it seems like the ZIP drive reads them at least but the MACBOOK comes up with the following message...
    'The disk you inserted was not readable by this computer'
    Does this pretty much mean a no go then?  Or can I put the samples from my AKAI sampler back through the old ZIP drive,  reformat some new disks in a certain way on that drive so that my MAC can read them?
    All its for really is mainly to take old tracks that used these samples and getting them set up in my mac.  Also there was some good bits and pieces there anyway and would like to keep using those samples for newer projects. I could of coourse resample them from the AKAI straight to the MAC but would be not as practical and would take alot longer. The 13'' macbook pros input is not digital, only its output.
    thanks

  • Is there a way i can backup my itunes library to a zip drive?

    i have an iomega zip drive and 250mb zip disc and i didnt know if theres a way to backup my itunes library to my zip drive.since i'v spent a lot of money on songs from itunes music store and dont want to lose them if my computer gets an virus or a glitch and erases my songs.now i know i can put my songs to an cd but i dont know how to that and if an cd can hold 150 songs and 11.1 hours since that how many songs and hours i have on my itunes.so can some one please tell me how to backup my itunes library to a zip drive or if i even can.
    thanks in advance.
    itunes 6.0.4 and ipod nano 2g   Windows XP  

    If your tracks will fit on a Zip drive, yes, you can use a Zip to back up. A CD holds about 650MB, so a 250MB Zip disk will hold less than half what a CD will. Just locate the tracks in your iTunes Music folder and drag them onto the Zip. You can use multiple disks if you have more tracks than will fit onto one Zip disk.
    Zip disks are notoriously unreliable, though - as bad or worse than floppy disks - so it wouldn't be my first choice for a backup medium. Of the couple of dozen Zip disks I used to own, over 75% of them eventually failed.

Maybe you are looking for