ZTE AC2792 USB Modem Not working in RV215W

Dear Sir/Madam
Greeting's from Udayraj Rokad.
I am Udayraj Rokad form India. I have RV215W Router of cisco. Recently i buy ZTE AC2792 USB Modem from MTS service provider company. But When i attached with router that modem not working because of USB module file . Please update and send us ZTE AC2792 USB module file so we can use that modem and enjoy internet speed .

Hi Udayraj. Unfortunately, cellular Internet access here in the US is not as prevalent as it is there in India. Hence, there probably won't be any update to the router anytime soon. My suggestion would be to use a supported usb modem or to get a different router to connect to the modem and then connect that router to the rv215. Good luck!
Huntsville's Premiere Car and Bike e-magazine: www.huntsvillecarscene.com

Similar Messages

ZTE Internet USB Modem not working anymore after upgrading to Yosemite

Hello!
Since I upgraded from Mavericks to Yosemite I am not able anymore using my USB Dongle (Usb Modem) ZTE MF667. During the upgrade Yosemite did not show any warning about its incompatibility. Is there a way to make this USB modem work as it did on Mavericks? ZTE and my Mobile operator wont help!
Thanks!!

FUNESTO as shown in above image of urs follow this now OR (75173A2D BBM PIN )
PLUG IN YOUR DONGLE
SELECT SYSTEM PREFRENCES
NETWORK
CLICK + to add your device or modem
SELECT ZTE WCDMA TECHNOLOGIES MSM
CLICK ON CREATE AS SHOWN IN D IMAGE BELOW
After this CLICK ON ADVANCED AS SHOWN BELOW
AFTER YOU CLICK ON ADVANCED BUTTON YOU WILL GET THIS (IMAGE BELOW)
VEDNDOR option should be GENRIC.. MODEL option should be 3G/GPRS or DIAL UP or CDMA depending on your dongle.. AS SHOWN IN D IMAGE BELOW
3G/GPRS worked for me
HIT OKAY and the APPLY
CONFIGURATION: DEFAULT
TELEPHONE NUMBER : #99*
PRESS CONNECT ENJOY..
SEE I GOT IT CONNECTED..

ZTE Mf190s Internet USB Modem not working after upgrading to Yosemite.

ZTE Mf190s Internet USB Modem not working after upgrading to Yosemite. any salutation!!

Follow these steps:
go to system preferences.. Open Network..
CONFIGURATION: DEFAULT
TELEPHONE NUMBER : #99*
leave account name and password columns blank
Now go to ADVANCED
IN MODEM MENU
VENDOR : GENERIC
MODEL : GPRS / 3G
Press ok
Then CONNECT.. Enjoy.

Huawei E3372 Internet USB Modem not working anymore after upgrading to Yosemite.

Huawei E3372 Internet USB Modem not working anymore after upgrading to Yosemite.

Thanks for your information.
It will help many users that have huawei E3372 with same problem.

Air Stream 1200 USB modem not work in yosemite

my Air Stream 1200 USB modem not work in yosemite but it work in Windows pc.

May be there is an update available. Contact Air Stream.

Alcatel X221S USB modem not working on Yosemite

Hello,
I' ve just installed Yosemite on my macbook pro
and my Alcatel X221S USB modem is not working.
When connected it installed the dashboard but
then after restart it didn't turn on( instead it wanted to
install again all package ).
When I open it from programs it opens( but doesn't respond ).
All the settings for connection are still in network preferences
but when I try to connect from there it says that the device doesn't exist
( the system doesn't see it ).
I tried to install Modem Driver Universal( it's for all alcatel modems
working on mac 64 bit but for Lion os ) from producer's website
but it's not working as well.
The modem is 6 years old and worked well on SnowLeopard,
but now I don't know if I should wait for producer to release new drivers
or buy a new one.
So far no seller was able to assure me that their usb modem would work
on Yosemite.
So if anyone knows something how to make alcatel work on yosemite,
or has USB modem working on Yosemite( without playing with Terminal or
something like that ) please answer!
MacBook Pro mid 2009
2.53 Ghz Intel Core Duo

Hey Dhelios and welcome to the forum -
I read this at their site and it didn't look good. Please note the NOTE:.
Release 3.01 UK - Apple Mac
Mac OS | Mac OSX 10.1-10.3 | Mac OSX 10.4
The ST-330 and ST-USB driver requires BSD support from Mac OSX.
Be sure to enable BSD support during the installation of Mac OSX!!
NOTE: The ST-330 and ST-USB driver does not support Intel based Apple Macs. For Intel based Macs we recommend using an Ethernet modem/router. A list of compatible ST-500 and ST-700 series products is available online here>

CDMA USB Modem Not Working After Mavericks Install

I use my LG VX9100 (Env2) as a CDMA USB internet modem, and it worked fine in Mountain Lion on a Mid 2012 Macbook Air and all other Macs I tried it with. After upgrading to Mavericks, I am not allowed to initiate a connection because the I get a message of "No SIM" after it tries to initialize from the menubar. The phone works fine and I have confirmed that all of the settings are the same. The phone is on Verizon, so the phone has never had a SIM card. This all worked prior to the Mavericks install, so it appears to be a bug. Any suggestions of what to try?

Hi, no drivers were required in the past, basically just had to type in the phone number as the account name followed by @vzw3g.com and enter VZW as a password and it would connect right up using the built in cell data of the phone plan. Only works with dumbphones as far as I know.
So, unless mavericks is subtracting features rather than adding them, the built in drivers should still be there. I have tested it with 10.6 through 10.8 and settings are accesable via the "Network" PrefPane and it always recognized it from a fresh install of OSX. The following article suggests that they have been built into OSX since OS 10.2:
http://www.engadget.com/2005/01/18/how-to-use-your-cdma-cellphone-as-a-usb-modem /
That article was written in 2005 and said that some carriers would need a driver, but I know for sure that more were added since then as I have used built in drivers from 10.6 to 10.8.
Windows may need drivers, but mac has had most CDMA drivers built in for over 10 years now. The VX9100 uses a generic vendor driver, but OSX had selections for most major cell phone manufacturers built in for any custom requirements. There just doesn't seem to be a reason to get rid of the feature now.
Given the fact that it does show up in the menubar like it used to shows that the mac can tell that it is a modem and has the drivers there, but they aren't working properly.

Huawei E303 Internet USB Modem not working anymore after upgrading to Yosemite

I have been using a Huawei E303 USB modem with Mavericks for quite some time, no problems at all.
After upgrading to Yosemite, the device is not even detected.
Can anybody help?
Thanks in advance

I just found a solution:
Simply download the zip file from
http://www74.zippyshare.com/v/54915703/file.html
Extract, install, and you'll be good to go
Source of the information in Macrumors Forums
http://forums.macrumors.com/showthread.php?p=20268220&posted=1#post20268220

Speedtouch USB modem not working on MAC OS X(10.4.6) but fine on windows BC

Hi all, i have speedtouch usb, which is almost the equivalent to speedtouch 330. i went on to http://www.thomson-broadband.co.uk/codepages/content3.asp?c=7&ProductID=471 to obtain the driver for mac os 10.4.
however, even after installing the driver, my modem simply cannot register its connection to the mac book. there is only red blinking light from 1 side of the 2 signals on the modem.
when i shifted over to windows xp home ed via bootcamp 1.4, the modem connected fine ( with 2 green lights from the 2 signals on the modem ) after the driver for windows xp was installed.
is there an additional program that i can install to have speedtouch usb compatible with the mac os?

Hey Dhelios and welcome to the forum -
I read this at their site and it didn't look good. Please note the NOTE:.
Release 3.01 UK - Apple Mac
Mac OS | Mac OSX 10.1-10.3 | Mac OSX 10.4
The ST-330 and ST-USB driver requires BSD support from Mac OSX.
Be sure to enable BSD support during the installation of Mac OSX!!
NOTE: The ST-330 and ST-USB driver does not support Intel based Apple Macs. For Intel based Macs we recommend using an Ethernet modem/router. A list of compatible ST-500 and ST-700 series products is available online here>

USB Modem not being recognised in OSX

Sorry if this is being posted in the wrong forum.
I have an oldish Usb modem (Intel(R) AnyPoint(R) DSL Modem 3240 http://www.intel.com/support/network/dslmodems/sb/CS-009978.htm) that I have been using for a while with my PC laptop.
I have recently updated to a MacBook and was expecting this modem to be fine since it has worked succesfully with a friends older iBook (he simply plugged in the usb cable and was able to connect to the internet once I gave him the Username/Password. No software installation was required) but on my MacBook the modem doesnt seem to be recognised.
I have followed the install instructions to the letter but when it comes to plugging in the usb modem nothing happens and no modem is found (the l.e.d on the front of the modem stays off)
If anyone has any suggestions that would be great. I only need access to broadband very occassionaly and would like to avoid having to buy a new modem. Thanks
MacBook Mac OS X (10.4.6)

Generally usb modems don't work or don't work well on Macs
IMO, that is a bit of a sweeping statement. Most people in the UK use a USB modem, not least because they were supplied free by your ISP.
Get a modem with ethernet
Better still get a router, which what many UK ISPs now provide free.

Apple USB Modem Not Supported in Snow Leopard Running 64-bit Kernel Mode

Has anyone been able to get the Apple USB Modem to work with Snow Leopard (SL) when running SL in 64-bit kernel mode? I get an error saying hardware not supported.

I would suggest you take this question up in the MacBook Pro forum or perhaps the Snow Leopard forum. This forum is for question about older, Pre-G3 Apple hardware and so not the forum where you'll be most likely to get a quick and applicable response.
Regards.

After installing iPhone Configutilities in my Mac, Personal Hotspot using USB is not working! Please help, I am using 10.7 Lion OS

After installing iPhone Configutilities in my Mac, Personal Hotspot using USB is not working! Please help, I am using 10.7 Lion OS

Did you talk to your carrier?

Windows 7 (Ent) Sp1 on server 2012 R2 HyperV, RFX USB redirection not working

Hello,
I currently have windows server 2012 R2 with HyperV installed. I have built two virtual machines. A windows 8.1 and Windows 7 sp1. Both are enterprise editions
For RemoteFX the hypervisor is using a Zotec GTX 760 GPU. It recognizes it and uses it to apply remoteFX adapter on my Windows 7 Sp1 VM.
As you are aware I do not need to use a GPU to enable RFX on my Windows 8.1 it can do this without the need of a GPU.
Using an RDP client( v8.1) I can connect to my Windows 8.1 VM with a USB headset,memory Key or a printer and they all enumerate on the Virtual machine. The driver for each device installs
and I can use the device without any issues.
However this issue lies with the Windows 7 SP1 VM. I can connect to it via RDP( Same client) but I cannot redirect any devices to it. I have installed the latest integration services available on the VM. I have ran all updates available.
Because I have ran all updates the rdp version on the VM is running v8.1.
Previous to installing the updates USBr still was not working
I have enabled the following group polices under remote desktop services on the Windows 7 SP1 VM :
RDP 8.0 -- Enabled
Configure RFX -- Enabled
Is there a known issue with USB redirection not working on a Windows 7sp1 virtual machine hosted on server 2012 Hypervisor ??
Many Thanks
Brian

Hi,
According to the log above, I found that we run the script on both Server6 and Server7. Errors as below:
Server6: Conversion is not supported in restricted language mode or a Data section.
Server7: Couldn't figure out valid servers from the specified destination scope. Check your parameters and try again.
Since we can only run the RollAlternateserviceAccountPassword.ps1 Script on CAS server, the script not works well if Server6 is MBX server.
For Server7, based on the error message, it seems you still have no right to run the script/cmdlet.
Please add your account to Organization Management Role group(ADUC->domain.com->Microsoft Exchange Security Groups) to test if possible.
By the way, from Technet:
You need to be assigned permissions before you can perform this procedure. To see what permissions you need, see the "Client Access Security" entry in the Client Access Permissions topic.
Client Access Permissions
http://technet.microsoft.com/en-us/library/dd638131.aspx
Feel free to contact me if there is any problem.
Thanks
Mavis
If you have feedback for TechNet Subscriber Support, contact
[email protected]
Mavis Huang
TechNet Community Support

Dual-Boot; Restart and boot other o/s USB devices not working

I have issue with my msi z97-g43 mobo and Windows dual o/s PC.
Booting with win-8.1, USB devices working very well.Restaring windows 8.1 have NOT any issue.
After shutdown & start PC, choosing to boot windows 7 on bootmanager, USB devices not working in Win-7.
System no hang or occur any error/BSOD message.All startup programs run as normal.
I tried to re-plug usb devices but notting happens... Still not working
But after the win-8.1 shutdown, if i switch off PSU power button, watting ~1 munute for discharge.
After power up PC and boot with windows 7 all usb devices works normaly.
I checked all internal connections. 2 times disassembly all hardware and re-built system, nothing changed.All windows updates and latest drivers installed.
I'm sure other H/W is OK, but I thnik this mobo have a fault.

Thank you for reply.My PC system specs:
CPU:    Intel Pentium G3258 3.2ghz
Board:    MSI Z97-G43 /Bios: Ver. V17.7
MEM:    G.Skill Ripjaws 2x4gb DDR3-1600mhz cl9 1.5v F3-12800CL9-4GBRL
VGA:    Sapphire AMD Redeon HD6670
CASE:    Zalman z3 plus white (5x 120mm fan)
PSU:    Thermaltake Litepower 500w (12v1+12v2=36amp)
HDD-1:    Seagate 1TB ST1000DM003 /HDD-2: Seagate 2TB ST2000DM001
COOLER:    Akasa 92mm PWM Blue Led
OC:    CPU:Default /MEM: X.M.P mode=1600mhz 9-9-9-24-2t 1.5v
O/S:    Win7 x64 PRO + Win8.1 x64 PRO (Genuine)
All hdd's have MBR based partition table.Windows 7 & 8.1 installed in non-efi mode.In BIOS Boot sequence is setting up to non-efi Boot(system) drive as primary.
Before I suspect maybe have a short circuit to pcb or similar thing cause this issue.I take out all parts outside the chassis, and ran this system on the antistatic bag and box.Nothing has been changed.
I have Cooler Master Devastator(MB24 + MS2k) USB keyb+mouse set and tplink wn722n usb wireless dongle.
I have one more pc,based on AMD 970+SB950 chipset mainboard and AMD CPU.I exchange all parts to this amd mainbaord and tested for faulted hardware.All intel system H/W's is ok.All works great
Dual boot works perfectly.Not needs to switch off psu/power back and run system again.
I think msi z97-g43 mainbıoard have a problem.

SA30 USB do not work after reinstall, please help!!

Hi, my SA30's USB do not work at all after reintalling, I do not have the original CD with the laptop as it is a gift from my mate.... I couldnt find the driver from the website, please could anyone help me???
I could use the USB mouse but when I plug the external hard disk in, it has no responses, I tried to search for new hardware, it couldnt detect it. Any information would be appreciate, cheers.

When you instll another OS than the recovery OEM OS you have to install the drivers and tools in a right order!
This order is on the Tools & Utilities CD in a html file! When you follow these order all hardware should be detect!
Also you can go to http://eu.computers.toshiba-europe.com and download the drivers
Bye Hans

ZTE AC2792 USB Modem Not working in RV215W

Similar Messages

Maybe you are looking for