Zynq custom board not booting from SD-Card

Hi all,
I have a custom designed board woth a Zynq XC7Z100 SoC and try to bring it up. The schematics are based on the ZC706 board so the MIO connections on the PS are the same.
Now I'm trying to boot just the simple Hello World example from XSDK (Vivado Version 2014.3). Booting from JTAG and from QSPI Flash is working but booting from SD-Card fails. The FSBL is producing the following output:
Xilinx First Stage Boot Loader
Release 2014.3 Nov 5 2014-17:42:52
Devcfg driver initialized
Silicon Version 3.1
Boot mode is SD
SD: rc= 0
SD: Unable to open file BOOT.BIN: 3
SD_INIT_FAIL
FSBL Status = 0xA009
This Boot Mode Doesn't Support Fallback
In FsblHookFallback function
I've measured all data pins and they are toggling. What I've found out is that the SDIO Clk is somehow strange. When starting the FSBL it is a very slow clock (kHz) and afterwards it's speeding up to 41.6666 MHz. I've already changed the SDIO clock in Vivado from 125 MHz to 50 MHz but nothing changes, when I'm measuring it. Do I miss something out?
Any help would be greatly appreciated.
Thanks
Christoph

I believe the clock is behaving properly. The driver should connect at a slow clock at first then increase to the highest clock that the driver thinks the card can support. If you see this clock speed change, the initialization must be getting past the first few SD card messages. You could try to adding printfs in the card driver to see which message failed.
I've had problems switching from 14.7 to 2014.3 FSBL. The later driver dropped support for older SD card and stop on very first message to the card. Maybe try a different card.
In going from dev board to custom board, did you switch from full size SD to micro SD? The micro SD format does not have a WP signal. Maybe no CD signal either. The FSBL driver cares about both.
Some official answers:
http://www.xilinx.com/support/answers/59476.html
http://www.xilinx.com/support/answers/52023.html

Similar Messages

IMac will not boot from any mode except Target Disk

I have an Early 2008 Penryn iMac 24" MB398LL/A running OS X 10.7.4 (see specs below) that will not boot from ANY mode, It also has several strange vertical bars from top to bottom on the screen. They are about 10 px wide, with some pixels empty and looks a bit like a barcode if you squint at it.
I have tried Safe Boot, Force Boot, DVD Boot, FireWire/USB Boot, and it always gets to the same point. It gets to the apple screen with the spinning gear and then after about 8 seconds it freezes. The only way it works at all is in Target Disk Mode. It pops right up on my Macbook Pro and I was able to grab all my info!
I have run Disc Utilities and Tech Tool on it many times from my MBP and it passes every test.
I reformatted the HD and installed 10.7 again, it still freezes up at the same point.
I have tried using Single User mode and every time have had to run /sbin/fsck -fy twice because it always says the disk is ok but it was modified on the first pass.
I thought maybe it had a bad video card or logic board but and I ran the Apple Hardware Test on many occasions and it always passes. Recently I was told about Loop Mode and just completed running the AHT for just over 30 hours without any errors at all.
UPDATE...
Strange Part… I tried installing Mountain Lion in Target Disk Mode and everything went smoothly. When it restarted on its own the lines on the screen were gone for the moment, but the Mac still freezes up on the spinning gear and immediately restarts on its own. I have run every thing listed above on it and still nothing. Sometimes the lines reappear then in two more starts they are gone.
I did manage to have it start one time got a copy of the the error report (its at the bottom too) The Mac ran for at least 30 minutes with no problems, then the screen went crazy a few seconds and it became unresponsive. The mouse moved but that was all it could do. Now my iMac continually restarts itself, I don't have any more ideas, HELP!
Specs...
The iMac "Core 2 Duo" 3.06 24-Inch Aluminum (Early 2008/Penryn) features a 3.06 GHz Intel "Core 2 Duo" processor (E8435), with two independent processor "cores" on a single silicon chip, a 6 MB shared level 2 cache, a 1066 MHz system bus, 2 GB of RAM (800 MHz DDR2 SDRAM, PC2-6400), a 500 GB (7200 RPM) Serial ATA hard drive, a vertically-mounted slot-loading DVD±R DL "SuperDrive", NVIDIA GeForce 8800 GS graphics acceleration with 512 MB of GDDR3 memory, a built-in iSight video camera, and built-in stereo speakers underneath the 24" glossy TFT Active Matrix LCD (1920x1200 native) display.
Error Report…
Sat Sep 1 17:13:12 2012
panic(cpu 0 caller 0xffffff801a4b7b95): Kernel trap at 0xffffff7f9bab8654, type 14=page fault, registers:
CR0: 0x000000008001003b, CR2: 0x0000000000000010, CR3: 0x0000000011803000, CR4: 0x0000000000000660
RAX: 0x0000000000000001, RBX: 0xffffff8050e00000, RCX: 0xffffff801aa8eb00, RDX: 0xffffff80602dba38
RSP: 0xffffff80602dbb60, RBP: 0xffffff80602dbb60, RSI: 0x0000000000000000, RDI: 0x0000000000000000
R8: 0x0000000000000000, R9: 0x00000000000000ff, R10: 0xffffffffffffffff, R11: 0x00000000ffffffff
R12: 0xffffff8050e00000, R13: 0x0000000000000000, R14: 0x0000000000000002, R15: 0x0000000000000000
RFL: 0x0000000000010246, RIP: 0xffffff7f9bab8654, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0x0000000000000010, Error code: 0x0000000000000000, Fault CPU: 0x0

Here is the complete error log...
Sat Sep 1 17:13:12 2012
panic(cpu 0 caller 0xffffff801a4b7b95): Kernel trap at 0xffffff7f9bab8654, type 14=page fault, registers:
CR0: 0x000000008001003b, CR2: 0x0000000000000010, CR3: 0x0000000011803000, CR4: 0x0000000000000660
RAX: 0x0000000000000001, RBX: 0xffffff8050e00000, RCX: 0xffffff801aa8eb00, RDX: 0xffffff80602dba38
RSP: 0xffffff80602dbb60, RBP: 0xffffff80602dbb60, RSI: 0x0000000000000000, RDI: 0x0000000000000000
R8: 0x0000000000000000, R9: 0x00000000000000ff, R10: 0xffffffffffffffff, R11: 0x00000000ffffffff
R12: 0xffffff8050e00000, R13: 0x0000000000000000, R14: 0x0000000000000002, R15: 0x0000000000000000
RFL: 0x0000000000010246, RIP: 0xffffff7f9bab8654, CS: 0x0000000000000008, SS: 0x0000000000000010
Fault CR2: 0x0000000000000010, Error code: 0x0000000000000000, Fault CPU: 0x0
Backtrace (CPU 0), Frame : Return Address
0xffffff80602db800 : 0xffffff801a41d5f6
0xffffff80602db870 : 0xffffff801a4b7b95
0xffffff80602dba40 : 0xffffff801a4ce4ad
0xffffff80602dba60 : 0xffffff7f9bab8654
0xffffff80602dbb60 : 0xffffff7f9baa218c
0xffffff80602dbbb0 : 0xffffff7f9baa20e2
0xffffff80602dbbd0 : 0xffffff7f9ba73554
0xffffff80602dbc00 : 0xffffff7f9aa8d470
0xffffff80602dbc40 : 0xffffff7f9aa8d3df
0xffffff80602dbc60 : 0xffffff7f9aa926ec
0xffffff80602dbcf0 : 0xffffff7f9aa8af20
0xffffff80602dbd20 : 0xffffff7f9aadacc7
0xffffff80602dbd70 : 0xffffff801a833b9b
0xffffff80602dbdc0 : 0xffffff801a862d57
0xffffff80602dbe30 : 0xffffff801a497cef
0xffffff80602dbe80 : 0xffffff801a420abd
0xffffff80602dbeb0 : 0xffffff801a410448
0xffffff80602dbf00 : 0xffffff801a4195fb
0xffffff80602dbf70 : 0xffffff801a4a5ad6
0xffffff80602dbfb0 : 0xffffff801a4ced13
      Kernel Extensions in backtrace:
         com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000->0xffffff7f9aab8fff
            dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
         com.apple.NVDAResman(8.0)[6A699209-FB98-316B-A3C0-DCA82AA8C86B]@0xffffff7f9aad8 000->0xffffff7f9addafff
            dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
            dependency: com.apple.iokit.IONDRVSupport(2.3.4)[99CA4184-8D92-31B2-8726-46139E8E3DFF]@0xff ffff7f9aac4000
            dependency: com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000
         com.apple.GeForce(8.0)[4B9BE287-5251-398E-96B0-BB16C9BFB2D9]@0xffffff7f9ba72000 ->0xffffff7f9bb34fff
            dependency: com.apple.NVDAResman(8.0.0)[6A699209-FB98-316B-A3C0-DCA82AA8C86B]@0xffffff7f9aa d8000
            dependency: com.apple.iokit.IONDRVSupport(2.3.4)[99CA4184-8D92-31B2-8726-46139E8E3DFF]@0xff ffff7f9aac4000
            dependency: com.apple.iokit.IOPCIFamily(2.7)[8C9E06A4-13D0-33F5-A377-9E36F0ECC229]@0xffffff 7f9aa4d000
            dependency: com.apple.iokit.IOGraphicsFamily(2.3.4)[2600903C-EEDE-321B-A023-169DC9B26EA6]@0 xffffff7f9aa81000
BSD process name corresponding to current thread: WindowServer
Mac OS version:
12B19
Kernel version:
Darwin Kernel Version 12.1.0: Tue Aug 14 13:29:55 PDT 2012; root:xnu-2050.9.2~1/RELEASE_X86_64
Kernel UUID: 3005059E-270B-3B9F-940D-7A66C05DDC9D
Kernel slide:     0x000000001a200000
Kernel text base: 0xffffff801a400000
System model name: iMac8,1 (Mac-F227BEC8)
System uptime in nanoseconds: 26349024446
last loaded kext at 22534854703: com.apple.driver.AppleHDAHardwareConfigDriver          2.3.0f2 (addr 0xffffff7f9c489000, size 12288)
loaded kexts:
com.apple.driver.AppleHDAHardwareConfigDriver          2.3.0f2
com.apple.driver.AppleHDA          2.3.0f2
com.apple.driver.AppleTyMCEDriver          1.0.2d2
com.apple.filesystems.autofs          3.0
com.apple.iokit.IOBluetoothSerialManager          4.0.9f8
com.apple.iokit.IOBluetoothUSBDFU          4.0.9f8
com.apple.driver.AppleLPC          1.6.0
com.apple.driver.AppleMuxControl          3.2.6
com.apple.driver.AppleBacklight          170.2.3
com.apple.driver.AppleUpstreamUserClient          3.5.10
com.apple.driver.AppleMCCSControl          1.0.33
com.apple.GeForce          8.0.0
com.apple.driver.AppleSMCPDRC          1.0.0
com.apple.iokit.IOUserEthernet          1.0.0d1
com.apple.Dont_Steal_Mac_OS_X          7.0.0
com.apple.driver.ApplePolicyControl          3.2.6
com.apple.driver.ACPI_SMC_PlatformPlugin          1.0.0
com.apple.driver.AppleIRController          320.15
com.apple.iokit.SCSITaskUserClient          3.5.1
com.apple.driver.AppleFileSystemDriver          3.0.1
com.apple.AppleFSCompression.AppleFSCompressionTypeDataless          1.0.0d1
com.apple.AppleFSCompression.AppleFSCompressionTypeZlib          1.0.0d1
com.apple.BootCache          34
com.apple.driver.XsanFilter          404
com.apple.iokit.IOAHCIBlockStorage          2.2.1
com.apple.driver.AppleFWOHCI          4.9.5
com.apple.driver.AppleUSBHub          5.1.6
com.apple.driver.AirPortBrcm43224          600.36.17
com.apple.iokit.AppleYukon2          3.2.3b1
com.apple.driver.AppleAHCIPort          2.4.0
com.apple.driver.AppleIntelPIIXATA          2.5.1
com.apple.driver.AppleUSBEHCI          5.1.5
com.apple.driver.AppleUSBUHCI          5.1.5
com.apple.driver.AppleEFINVRAM          1.6.1
com.apple.driver.AppleRTC          1.5
com.apple.driver.AppleHPET          1.7
com.apple.driver.AppleACPIButtons          1.6
com.apple.driver.AppleSMBIOS          1.9
com.apple.driver.AppleACPIEC          1.6
com.apple.driver.AppleAPIC          1.6
com.apple.driver.AppleIntelCPUPowerManagementClient          196.0.0
com.apple.nke.applicationfirewall          4.0.39
com.apple.security.quarantine          2
com.apple.driver.AppleIntelCPUPowerManagement          196.0.0
com.apple.driver.DspFuncLib          2.3.0f2
com.apple.iokit.IOAudioFamily          1.8.9fc9
com.apple.kext.OSvKernDSPLib          1.6
com.apple.kext.triggers          1.0
com.apple.iokit.IOSerialFamily          10.0.6
com.apple.driver.AppleSMBusPCI          1.0.10d0
com.apple.driver.AppleBacklightExpert          1.0.4
com.apple.driver.AppleSMBusController          1.0.10d0
com.apple.nvidia.nv50hal          8.0.0
com.apple.NVDAResman          8.0.0
com.apple.iokit.IOFireWireIP          2.2.5
com.apple.driver.AppleHDAController          2.3.0f2
com.apple.iokit.IOHDAFamily          2.3.0f2
com.apple.iokit.IOSurface          86.0.2
com.apple.iokit.IOBluetoothFamily          4.0.9f8
com.apple.driver.AppleGraphicsControl          3.2.6
com.apple.iokit.IONDRVSupport          2.3.4
com.apple.iokit.IOGraphicsFamily          2.3.4
com.apple.driver.AppleSMC          3.1.3d11
com.apple.driver.IOPlatformPluginLegacy          1.0.0
com.apple.driver.IOPlatformPluginFamily          5.2.0d16
com.apple.iokit.IOUSBHIDDriver          5.0.0
com.apple.driver.AppleUSBMergeNub          5.1.5
com.apple.driver.AppleUSBComposite          5.0.0
com.apple.iokit.IOSCSIMultimediaCommandsDevice          3.5.1
com.apple.iokit.IOBDStorageFamily          1.7
com.apple.iokit.IODVDStorageFamily          1.7.1
com.apple.iokit.IOCDStorageFamily          1.7.1
com.apple.iokit.IOATAPIProtocolTransport          3.5.0
com.apple.iokit.IOSCSIArchitectureModelFamily          3.5.1
com.apple.iokit.IOFireWireFamily          4.5.5
com.apple.iokit.IOUSBUserClient          5.0.0
com.apple.iokit.IO80211Family          500.15
com.apple.iokit.IONetworkingFamily          3.0
com.apple.iokit.IOAHCIFamily          2.2.0
com.apple.iokit.IOATAFamily          2.5.1
com.apple.iokit.IOUSBFamily          5.1.6
com.apple.driver.AppleEFIRuntime          1.6.1
com.apple.iokit.IOHIDFamily          1.8.0
com.apple.iokit.IOSMBusFamily          1.1
com.apple.security.sandbox          220
com.apple.kext.AppleMatch          1.0.0d1
com.apple.security.TMSafetyNet          7
com.apple.driver.DiskImages          344
com.apple.iokit.IOStorageFamily          1.8
com.apple.driver.AppleKeyStore          28.18
com.apple.driver.AppleACPIPlatform          1.6
com.apple.iokit.IOPCIFamily          2.7
com.apple.iokit.IOACPIFamily          1.4
com.apple.kec.corecrypto          1.0
Model: iMac8,1, BootROM IM81.00C1.B00, 2 processors, Intel Core 2 Duo, 3.06 GHz, 2 GB, SMC 1.30f1
Graphics: NVIDIA GeForce 8800 GS, NVIDIA GeForce 8800 GS, PCIe, 512 MB
Memory Module: BANK 0/DIMM0, 1 GB, DDR2 SDRAM, 800 MHz, 0x2C00000000000000, 0x38485446313238363448445A2D3830304531
Memory Module: BANK 1/DIMM1, 1 GB, DDR2 SDRAM, 800 MHz, 0x2C00000000000000, 0x38485446313238363448445A2D3830304531
AirPort: spairport_wireless_card_type_airport_extreme (0x14E4, 0x8C), Broadcom BCM43xx 1.0 (5.10.131.36.16)
Bluetooth: Version 4.0.9f8 10405, 2 service, 18 devices, 1 incoming serial ports
Serial ATA Device: WDC WD5000AAKS-40YGA1, 500.11 GB
Parallel ATA Device: MATSHITADVD-R   UJ-875
USB Device: Built-in iSight, apple_vendor_id, 0x8502, 0xfd400000 / 2
USB Device: BRCM2046 Hub, 0x0a5c (Broadcom Corp.), 0x4500, 0x1a100000 / 2
USB Device: Bluetooth USB Host Controller, apple_vendor_id, 0x820f, 0x1a110000 / 5
USB Device: IR Receiver, apple_vendor_id, 0x8242, 0x5d100000 / 2
USB Device: Hub in Apple Extended USB Keyboard, apple_vendor_id, 0x1002, 0x1d100000 / 2
USB Device: Trackball, 0x046d (Logitech Inc.), 0xc404, 0x1d120000 / 4
USB Device: Apple Extended USB Keyboard, apple_vendor_id, 0x0204, 0x1d110000 / 3

Mid-2009 MacBook Pro sees internal SATA hard drive, but will not boot from or format

I inherited a Mid-2009 MacBook Pro (15-inch, 2.53 GHz model) with a very strange issue.
It first presented itself as not being able to boot from the internal SATA hard drive that came with the computer. Nothing I tried could get it to boot, so I assumed the file system was corrupted beyond repair and booted from a CD to try to format the drive. Disk Utility on the CD would not format the drive, giving me strange error messages like "Unable to write to the last block of the device".
At this point I figured the drive itself must be toast, so I pulled it out and put another known-good SATA hard drive in, booted from CD, and attempted to format. Again, same error messages and an unsuccesful format.
So I had the bright idea of formatting one of the drives in an external enclosure and then putting it in the MBP to see if OS X would even install. No dice. Get a cryptic error message before installation even begins.
So I installed OS X on the drive in the external enclosure and put it in the MBP, and it attempts to boot, but never goes anywhere.
So to sum up, the symptoms I'm seeing:
MacBook Pro CAN see internal SATA hard drives.
MacBook Pro WILL NOT boot from any internal SATA hard drive and cannot format or install OS X to any internal SATA hard drive.
MacBook Pro WILL boot from any CD or external device and seems to work properly otherwise.
At this point I'm thinking it's one of two things: the hard drive ribbon cable or the SATA controller on the logic board.
Since the MacBook Pro seems to work completely fine other than this one issue, and will boot properly from both external devices and the CD (also a SATA device), I'm thinking and hoping that it's just the hard drive ribbon cable. From my searches online, I've heard that this batch of MacBook Pros is known to have issues with the hard drive ribbon cable, but it seems in most cases this manifests itself by the Mac not being able to see a drive at all.
I've done quite a bit of troubleshooting to get to this point, but right now I'm just looking for any feedback at all. Specifically I'd love to know a way I can easily test to see whether it's the logic board or the cable.

UPDATE: An interesting development!
I just tried a third known-good SATA hard drive, one which I believe supports SATA I only (but I'm not sure), and unlike the other drives that the Mac sees but cannot properly interact with, the Mac can't even see this one when I put it inside.
Frustrating as this may be, I believe I'm actually getting closer to a solution since my symptoms now appear to be closely aligned with people having SATA ribbon cable issues.
Onward!

G4 that will not boot from any disc EXCEPT the Apple Hardware Test CD

We have a DP 1ghz Quicksilver PowerMac G4 that will not boot from any disc EXCEPT the Apple Hardware Test CD that came with the machine.
We were in the process of installing 10.4 Tiger before placing it for sale.
The Mac was originally OSX Server 10.1 that we later converted to a worksation running 10.3 Panther.
It has 1 GB of memory, 80GB hardrive, 250MB Zip Drive and a Radeon 7500 video card.
Since this machine only has a CD-R drive and not a DVD-R, we installed Tiger using another Mac via Target Disk Mode. The installation process went well, but when I tried to reboot I got a Kernel Panic right after startup screen with the grey Apple logo.
On some reboots we get to the blue startup screen, others it stops at the grey Apple logo, others a black box like the a Kernel Panic - but with no text. Twice it went directly into Open Firmware.
We have done the following during our troubleshooting:
- Reseat RAM, Video Card, Hard Drive, Zip & CD-R connections
- Remove RAM 1 stick at a time and reboot
- Replace RAM with RAM from another working Quicksilver
- Replace Video Card with one from another working Quicksilver
- Zap PRAM
- Reset CUDA switch
- Unplug the MAC and remove everything (RAM, Battery, etc) for 30 minutes and try to reboot
- Tried booting from the Macintosh Server G4 Software Restore CD
- Tried booting from Mac OS X Server CD
- Tried booting from AppleCare Protection Plan CD with TechTool
- Tried booting from Diskwarrior CD
- Tried booting from an external FireWire drive with a disk image of Tiger OS Install
- Tried booting with the hard drive disconnected
The Mac WILL boot from the Apple Hardware Test CD and will pass ALL of the extended tests.

Conventional wisdom says that any Mac that will not boot up from a System/Install CD OS 9 or an Install CD Mac OS X, has a Hardware problem.
The diagnostic CD is a red herring because it uses a very primitive method of reading the CD, and so does not properly represent the machines general ability to read CDs.
I would look at the CD drive cables, etc, and see if another drive gives different results.
You have not mentioned using the Startup Manager (option key at Startup) to do any checking:
HT1310- Startup Manager: How to select a startup volume

Intel Xserve will NOT boot from hard disk drive

I have two Intel Xserves 2.0 QC machines
I have tried to re-install version 10.4.11 OS (don't ask) onto a Hard disk drive that is in a Disk drive caddy and inserted in the machine.
When booting from The installation DVD media
The disk is seen by the "Disk Utility" (the disk is partitioned as GUID boot) and the installation proceeds to the disk.
Once the first pass of the installation is complete and the system reboots, the system shows the folder and ? mark.
If I boot and hold "ALT" key to view all avaialble boot options the Hard Disk Drive does NOT appear as valid boot disk.
It does show, the still inserted Installation DVD.
I CAN boot from an external firewire drive and the Hard disk drive is visible to the OS once logged in.
I have tried different caddy postions (left, middle and right)
I have tried bona fide Apple supplied Disk drives
I have tried various different caddies
I have tried installing Operating System 10.5.* and 10.6.8 server
I have run SMC reset and system reset
But still I cannot boot off from any Hard Disk Drive inserted in a caddy at the front of the system.
Has anyone seen this behaviour?
Is it fixable?
Do I have replace something like the Hard Disk Drive back plane circuit board? Or even the main logic board?
I have now run out of ideas and cannot find any help in discussions or just googling.
ANY help would be very appreciated
Regards
Tony

Antonio Hi !
QC = Quad core or QX as it is written on the "pull out" serial number tab at rear of system
I have 3 late 2006 Intel xserves
On my intial posting I declared 2 were 2.0 machines - when I was trying to be concise
2 of the macines are 2.66 systems and 1 is 2.0 system - all are QX machines
the 2.0 and 1 of the 2.66 will NOT boot from the ADM and disk inside the system - whereas the other 2.66 system will.
I have many different Caddies and these have different product/model number labels
603-9965
603-9545
603-9796
these are marked "intel SATA"
The 80Gb was only one of the drives tested - I have used Seagate 400Gb 750Gb and 1Tb - all of which have been used in systems at one time or another
and as I said the drives ARE visible once the operating system (either installation DVD or external firewire are booted from) - they are just NOT visible when the system is searching for boot media.
Thanks for the guide - I will look through that and continue to try and find an answer

How to boot from SD-card on Satellite Pro S300?

My windows 7 32bit based S300 has a build-in SD card reader. The Toshiba utility for making the SD card bootable comes with an error message stating Fault: 00-61-FF02-26.
Is does not see or recognize the card.
In the BIOS version 3.00 WIN there is also no possilility for booting from SD card.
The SD card can be formatted and you can read and write to the card.
Why is this not possible?

As far as I know the BIOS of the Satellite Pro S300 supports the following bootable devices:
- USB FDD,
- Primary HDD,
- ODD (or USB ODD),
- Network(LAN),
- SD-CARD,
- USB Memory, supported at the same time
So BIOS provides the booting from SD card.
You should try following way:
Insert the SD card in the SD card slot and then power up the notebook.
Then press F12 in order to get the boot menu. Now the SD card should appear in the menu

P10-873 boot from SD card?

Hi there
Is this possible? The BIOS has an option to enable/disable the SD slot so presumably the slot can be accessed to some extent at BIOS level. I've tried setting the Removable Drives to the top of the boot order and putting in an SD card with Windows 98 boot files on it, but it ignores this and boots from the hard drive. Is there a way?
Thanks
Mark

Hi Mark,
I had the same problems when I tried to boot from a SD card. I tried different settings but it didn't boot!
Then I called a toshiba technican and they told me that booting from SD card is at the moment not possible. Toshba is working on a solution, but we have to give them a little bit more time!
Cu Theo

V3-471G how to boot from SD CARD?

On the BIOS BOOT MENU I dont see any sd card option. Is it possible to enable booting from sd card?

as far as i know, it's not possible.

T400 Boot from SD card

Hi,
I just got a 8 GB SD card and I was wondering if anyone know how to or if its possible at all to install Ubuntu 8.10 in persistence mode to an SD card and have it run off that on a Lenovo T400.
Thanks.

In the user's manual, it is clearlu written that it can be boot from SD card. Anyway, I made it done with USB flash memory. Now, I am using my laptop with new Win XP. Although there was small glitch, it worked.
The program 'WinToFlash' seemed that it did not work, and I found accidently (pure coincident) software 'WinsetupFromUSB' version 0-2-3 in the internet, and followed the instruction. It worked. So, problem is solved anyway. Thank you for your help.

R100 Boot from PC-CARD?

Hi,
I own a SanDisk SDP3B 1.2GB (Industrial Grade) ATA PC-CARD which I'm trying to make bootable in order to run another O/S on. I'm also considering putting a recovery image on it with the help of Acronis TrueImage, so I just can boot from the card to restore my computer.
This isn't working well and I have not been successful in getting this to work. I'm wondering if anyone else have tried to boot off a pc-card with their R100's?
Thanks,
Tim

Hi
In my opinion there is no enough capacity for whole image on this card. I have no experience but try to check all BIOS settings. Check if there is a option called Boot from other devices.

Not booting from CD drive

Hi all. This is my first time posting so please bare with me. I am having a rather very difficult time getting my bios on this board to boot from the cd player. When I go into the bios settings to change the boot sequence (or pressing F11 for boot sequence) my cd player is not listed as a boot device. I know the bios is seeing the player because it is being listed during the post screens. I have tried this with both the os cd in the player and without it. Every now and then the bios will list the cd player as a boot option. When it does I'll change the 1st boot to cd and disable all the rest. I'll save and exit the bios settings and when the system reboots it boots back into the hard drive. I'll go back into the bios settings and lo and behold the boot sequence is back the way it was (1st-floppy, 2nd hard drive). Its like the bios had never saved the changes I made. Then I have to go back to trying to get the bios to list my cd as a boot option again. This goes on and on. My system ia about 2 months old and when I initially loaded the os system everything seemed to work fine. I sent an email to MSI's tech support several days ago but no reply yet. Can anybody out there give me some insight into what is going on with this thing.
Thanks, J

Was it 1 short or 1 long beep?
Quote
http://www.bioscentral.com/beepcodes/amibeep.htm
AMI BIOS Beep Codes:
Beeps
Error Message
Description
1 short DRAM refresh failure The programmable interrupt timer or programmable interrupt controller has probably failed
2 short Memory parity error A memory parity error has occurred in the first 64K of RAM. The RAM IC is probably bad
3 short Base 64K memory failure A memory failure has occurred in the first 64K of RAM. The RAM IC is probably bad
4 short System timer failure The system clock/timer IC has failed or there is a memory error in the first bank of memory
5 short Processor error The system CPU has failed
6 short Gate A20 failure The keyboard controller IC has failed, which is not allowing Gate A20 to switch the processor to protected mode. Replace the keyboard controller
7 short Virtual mode processor exception error The CPU has generated an exception error because of a fault in the CPU or motherboard circuitry
8 short Display memory read/write error The system video adapter is missing or defective
9 short ROM checksum error The contents of the system BIOS ROM does not match the expected checksum value. The BIOS ROM is probably defective and should be replaced
10 short CMOS shutdown register read/write error The shutdown for the CMOS has failed
11 short Cache error The L2 cache is faulty
1 long, 2 short Failure in video system An error was encountered in the video BIOS ROM, or a horizontal retrace failure has been encountered
1 long, 3 short Memory test failure A fault has been detected in memory above 64KB
1 long, 8 short Display test failure The video adapter is either missing or defective
2 short POST Failure One of the hardware testa have failed
1 long POST has passed all tests

Not booting from 10.4.8 volumes after upgrade from 10.4.7

I'm sorry to report that my aged G4 450 MHz AGP with 4 internal Hard disk drives no longer boots from any of the 2 volumes upgraded to Mac OS X 10.4.8 as soon as it was started from another volume!
All was working fine as long as 10.4.7 was installed on the 2 232 GB disks connected to the SIIG ATA133 controller. I could boot from any OS on any of the 4 disks, 5 partitions:
internal ATA66 bus:
18 GB disk, 2 partitions: 'IBM_18GB' with OS 9.2.2 and TechTool Pro's 'eDrive' with 10.4.7
71 GB disk, 1 partition 'IBM_71GB' with OS 9.2.2
PCI SIIG ATA133 controller:
232 GB disk, one partition 'I1232GB' with 10.4.7, now upgraded to 10.4.8 and no longer bootable
232 GB disk, one partition 'I2232GB' with 10.4.7, now upgraded to 10.4.8 and no longer bootable
Now I can only boot from the Mac OS 9.2.2 or the eDrive 10.4.7 partitions.
What I did so far: 'I2232GB' was my main OS X startup volume, 'I1232GB' contains a clone of it, plus additional folders like software base and backups.
After upgrading 'I2232GB' to Mac OS X 10.4.8 through Software Update and repairing permissions all was OK as long as the Mac was just shut down or re-started: it always booted up in Mac OS X 10.4.8 from 'I2232GB' without any problems.
The next day I booted from 'I1232GB' to do the same there.
Afterwards I could no longer boot in Mac OS X 10.4.8 from 'I2232GB' nor in in Mac OS X 10.4.8 from 'I1232GB': it just gets to the grey screen with the Apple logo, but the round circle underneath indicating some progress never appears. I left it there for hours: it just hangs.
With the Option key held at startup I could boot from the other partitions with Mac OS 9.2.2 or the eDrive with 10.4.7. None of their Startup Control Panels was able to get me back to 10.2.8!
So I booted from the TechTool Pro 4.5.1 DVD to Optimize both volumes, 'I1232GB' & 'I2232GB', always Files only.
Then I booted from the DiskWorrior 3.0.3 CD to rebuild the directories of both volumes, 'I1232GB' & 'I2232GB'.
Still I can not boot from either 'I1232GB' or 'I2232GB' in Mac OS X 10.2.8!
Downloaded the Mac OS X 10.2.8 Compo Update (for PPC) and installed it onto both 'I1232GB' & 'I2232GB' while booted from the eDrive which I keep on Mac OS X 10.4.7 - no luck either, still I can not boot from either 'I1232GB' or 'I2232GB' in Mac OS X 10.2.8!
Then I backed up the users folder from 'I2232GB' onto 'I1232GB', booted from Mac OS 9.2.2 and used Intech's Hard Disk Speedtools 3.6 to format 'I2232GB', afterwards initialized it with Alsoft's Plus Maximizer Extension for a Block Size of 512 Bytes.
Installed Mac OS X 10.4 from DVD, as well as iLive '06 and upgraded everything to the latest releases with Software Update. All was working fine with all the required reboots until another startup volume was chosen: afterwards again I can no longer boot back into Mac OS X 10.2.8 on the fresch installed 'I2232GB'!
Any help would be appreciated.
Here is some information found by System Profiler from Mac OS X 10.4.7, eDrive, let me know if you need more:
Hardware Overview:
Machine Name: Power Mac G4 (AGP graphics)
Machine Model: PowerMac3,1
CPU Type: PowerPC G4 (2.8)
Number Of CPUs: 1
CPU Speed: 450 MHz
L2 Cache (per CPU): 1 MB
Memory: 2 GB
Bus Speed: 100 MHz
Boot ROM Version: 4.2.8f1
Serial Number: XA00715VHSF
Sales Order Number: M7628LL/A
ATA Bus:
IBM-DPTA-372050:
Capacity: 19.12 GB
Model: IBM-DPTA-372050
Volumes:
IBM_18GB:
Capacity: 13.12 GB
Available: 6.96 GB
eDrive:
Capacity: 6 GB
Available: 3.03 GB
IBM-DTLA-307075:
Capacity: 71.59 GB
Model: IBM-DTLA-307075
Volumes:
IBM_71GB:
Capacity: 71.59 GB
Available: 39.65 GB
ATA Bus:
PIONEER DVD-RW DVR-107D:
Model: PIONEER DVD-RW DVR-107D
Firmware Revision: 1.21
Interconnect: ATAPI
Burn Support: Yes (Apple Shipped/Supported)
Cache: 2000 KB
IOMEGA ZIP 100 ATAPI:
Model: IOMEGA ZIP 100 ATAPI
ACARD,6880M:
Name: ACARD,6880M
Type: scsi
Bus: PCI
Slot: SLOT-C
Vendor ID: 0x1191
Device ID: 0x0009
Subsystem Vendor ID: 0x1191
Subsystem ID: 0x0009
Revision ID: 0x0003
SCSI Parallel Domain 65536:
Initiator Identifier: 7
ATA HDT722525DLAT80:
Capacity: 232.89 GB
Manufacturer: ATA
Model: HDT722525DLAT80
Revision:
Removable Media: Yes
BSD Name: disk2
OS9 Drivers: Yes
SCSI Target Identifier: 0
SCSI Logical Unit Identifier: 0
S.M.A.R.T. status: Not Supported
Volumes:
I1232GB:
Capacity: 232.89 GB
Available: 14.1 GB
Writable: Yes
File System: HFS+
BSD Name: disk2s3
Mount Point: /Volumes/I1232GB
ATA HDT722525DLAT80:
Capacity: 232.89 GB
Manufacturer: ATA
Model: HDT722525DLAT80
Revision:
Removable Media: Yes
BSD Name: disk3
OS9 Drivers: Yes
SCSI Target Identifier: 2
SCSI Logical Unit Identifier: 0
S.M.A.R.T. status: Not Supported
Volumes:
I2232GB:
Capacity: 232.89 GB
Available: 180.11 GB
Writable: Yes
File System: Journaled HFS+
BSD Name: disk3s3
Mount Point: /Volumes/I2232GB
The RAM consists of 4 identical modules and is about 1 year old:
DIMM0/J21 to DIMM3/J24:
Size: 512 MB
Type: SDRAM
Speed: PC133-333
Status: OK
Many thanks for your help!
Josef
Apple G4 AGP Mac OS X (10.4.8) 4 internal hard disks, dual layer DVD-RW, 2GB RAM

What I did so far: 'I2232GB' was my main OS X
startup volume, 'I1232GB' contains a clone of it,
plus additional folders like software base and
backups.
After upgrading 'I2232GB' to Mac OS X 10.4.8
through Software Update and repairing permissions all
was OK as long as the Mac was just shut down or
re-started: it always booted up in Mac OS X 10.4.8
from 'I2232GB' without any problems.
The next day I booted from 'I1232GB' to do the same
there.
Afterwards I could no longer boot in Mac OS X 10.4.8
from 'I2232GB' nor in in Mac OS X 10.4.8 from
'I1232GB': it just gets to the grey screen with the
Apple logo, but the round circle underneath
indicating some progress never appears. I left it
there for hours: it just hangs.
With the Option key held at startup I could boot from
the other partitions with Mac OS 9.2.2 or the eDrive
with 10.4.7. None of their Startup Control Panels was
able to get me back to 10.4.8!
So I booted from the TechTool Pro 4.5.1 DVD to
Optimize both volumes, 'I1232GB' & 'I2232GB',
always Files only.
Then I booted from the DiskWorrior 3.0.3 CD to
rebuild the directories of both volumes, 'I1232GB'
& 'I2232GB'.
Still I can not boot from either 'I1232GB' or
'I2232GB' in Mac OS X 10.4.8!
Downloaded the Mac OS X 10.4.8 Compo Update (for PPC)
and installed it onto both 'I1232GB' & 'I2232GB'
while booted from the eDrive which I keep on Mac OS X
10.4.7 - no luck either, still I can not boot from
either 'I1232GB' or 'I2232GB' in Mac OS X
10.4.8!
Then I backed up the users folder from 'I2232GB'
onto 'I1232GB', booted from Mac OS 9.2.2 and used
Intech's Hard Disk Speedtools 3.6 to format
'I2232GB', afterwards initialized it with Alsoft's
Plus Maximizer Extension for a Block Size of 512
Bytes.
Installed Mac OS X 10.4 from DVD, as well as iLive
'06 and upgraded everything to the latest releases
with Software Update. All was working fine with all
the required reboots until another startup volume was
chosen: afterwards again I can no longer boot back
into Mac OS X 10.4.8 on the fresch installed
'I2232GB'!
I found several typos in above post, wherever it was 10.2.8 it should have read 10.4.8 - I'm very sorry for confusing you, this would not have made sense, but I found no way to edit the existing text therefore I modified the quote of it here.
I do not need Mac OS X 10.2.8 back, but it would be nice to boot back in Mac OS X 10.4.8 from another volume as the current one - which was working fine before with Mac OS X 10.4.7.
Many thanks,
Josef

Will Not Boot from Install Disc & 4SNS/1/40000000: TG0D - Thermal Sensor?

*Will Not Boot from Install Disc*
I used the "option key" approach with the gray start up disk. At first it ejected the start up disk. Then I nudged the disk back in the machine and it showed on the screen as an option. I clicked on the start up disk image and it finally loaded.
But, it won't accept the start up disk when holding down the "C" key at restart.
*4SNS/1/40000000: TG0D*
I did an Apple Hardware Test and received the following diagnostic:
Version: 3A121
Test Suite: Extended Test
Loop Count: 2
Result: Failed
Failure code: 4SNS/1/40000000: TG0D
*Thermal Sensor*
A search for the failure code 4SNS/1/40000000: TG0D brought up an Apple Discussion topic entry stating: That error code indicates a problem with a thermal sensor. It could be not working or possibly not connected. You will need to take it to Apple for repair.
Would a thermal sensor have anything to do with it not starting up when holding down the "C" key at restart? What are thermal sensor problem symptoms?
*User File Folder Opened Up*
The machine also starts up with my user file folder opened up rather than with a blank screen as it normally should
I completed a DiskWarrior rebuild on the disk and verify disk shows it is fine.
Any suggestions on what to do next with these issues?

The answer was in your post: "You will need to take it to Apple for repair."

Can not boot from OSX disc

I recently partitioned my internal drive with an 80 gig partition to run Ubuntu , removed Ubuntu and now can not resize hd to recover the 80 gig that I used , there was a program with this Ubuntu install called rEFIt that was installed for the dual boot , My problem is that Itunes keeps crashing and I have spent somewhere around 8 hours trying to fix this issue and in the process I discovered that I now can not boot from the osx disc but I can boot from the Ubuntu disc , what can I do to correct this issue or is there anything that I can do to correct this and recover the 80 gig that I used ?

The only solution was to erase hd and restore from time machine backup......
According to everything that I have seen , read and tried when you partition the mac hd the way that mac is designed it will lock the hd thus preventing any access even using the startup disc to repair. As far as restoring everything after the erase and reinstall of the OSX that was easy and painless. FOR ANYONE WHO DOES NOT BACKUP THEIR DATA THIS IS WHY YOU SHOULD!!!!
Once OSX is reinstalled the migration assistant will ask if you want to restore from a backup , if you have time machine or any other sort of backup simply choose the one you wish to restore from and continue , must admit I was a bit hesitant at first , I must say that everything restored with the exception of some settings that I have had to restore but they were not major settings , after the backup is restored simply run update check and reinstall all updates , may need to do this a couple of times.
Depending on the amount of data you have will determine the length of time for restore (500 gigs about 6 hrs.) but it will restore user account settings , connection settings and network settings.
Hope this will help if anyone has experienced the same problem.

RE: HP XP Media Center 2005 Ed will not boot from HP System Restore CD's

RE: HP XP Media Center 2005 Ed will not boot from HP System Restore CD's.
The following instructions about the "Code Purple" error FAILED. Error is still present.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
***PLAIN ENGLISH QUICK AND EASY FIX FOR ALL SYSTEMS****
***Windows 7 code purple or Windows Vista code purple***
With the code purple error on the screen, press shift+f10 (the shift key and the F10 key (at the top of the keyboard) at the same time) to open a little screen called a command prompt. (So, you get a little black screen with white text that says something about your Windows verison first and a little ways down you'll see "C:\>".   It's all ready for you to start typing.)
Type the following line, just as you see it here...
notepad C:\hp\bin\checkdmi\checkdmi.cmd
so it will look like this
C:\>notepad C:\hp\bin\checkdmi\checkdmi.cmd
Press Enter.
You will see the text for the file listed in a window using a simple text editor.
Go to the beginning of the text. Press enter to make a space. Type this...
goto cleanup
So, whatever comes after, the first line looks like this...
goto cleanup
Save the file and exit notepad and restart your PC. You are good to go.
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
RESULT: Same error and problem.
So, NOW THE SCENARIO IS THIS...[ And A CHALLANGE TO ALL HP Software EXPERTS]
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
1. The PC will not boot the System Restore CD's
2. The Original OS install and [HP_RECOVERY] disk sector has been severely damaged by
all of the following:
   A. Massive Virus Infections as shown by Kaspersky Virus Scan and cleaned up.
   B. The user had originally updated the pc to Vista Business Express Upgrade
       (Supplied by HP with the original purchase and warranty).
        (Prior to the upgrade, Media Center was working correctly.)
   C. The original OS product key(XP Media Center Ed. 2005) has been changed by the Vista Business Express upgrade.
   D. The destructve recovery done by PC-Doctor has done user file damage(s).
   E. All software, and possibly hardware could be corrupted & damaged by viruses,
   incomplete recovery, and the unknown failures and conditions.
To sum up, the system is locked in an unknown state, waiting for expert help.
(I can allow and manage to let someone diagnose, repair remotely using another OS i.e.Linux Opensuse 12.1, or XP Home ed if needed.)
SO IF YOU THINK YOU ARE UP TO THIS CHALLANGE, SEND MESSAGES TO DAVHPForum anytime. Thanks in advance!
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

Hello @DAVHPForum,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I have read your post on how you are not able to boot your computer using the HP system restore CDs, and I would be happy to assist you in this matter!
If you are not able to recover your system by following the steps in this document, please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
I hope this helps!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Zynq custom board not booting from SD-Card

Similar Messages

Maybe you are looking for