24" Display size without the stand

can anyone tell me the actual size of 24" imac display without the stand.
The dimensions mentioned in the tech. specs. are including the stand.
Thanks in advance.

Hi suts and welcome to Discussions,
found them here: http://forums.macrumors.com/showthread.php?t=236158
24" iMac without stand: 57cm x 46cm (22.5" x 18.125"), 72cm diagonal (28");
LCD Screen only: 52cm x 32cm (20.5" x 12.5"), 61cm diagonal (24", of course).
Hope it helps

Similar Messages

  • What are the actual dimensions of the new Thunderbolt Display without the stand (e.g., when using a VESA mount)?

    I need to use the new Thunderbolt Display without the stand on a VESA mount, but before I order it I need to make sure it will fit height-wise in the allotted space.

    The ThunderBolt display specs page has the same sizes listed as the 27" LED Cinema Display specs page (web archive).  I just measured my Cinema Display for you and the height of the display itself without the stand is 15 5/8".  However, you will need some additional space at the bottom for air flow intake.  These displays get hot and need proper ventilation so do not block the vents on the bottom.  Also the bottom vents are where the speakers are.
    Hope this helps.

  • When creating a new DPS should I use sizes offered by InDesign or the display size of the device?

    Hello all,
    When creating a new DPS, should I use the sizes offered by InDesign or the display size of the device?  I ran into this question when I was looking up the sizes of different devices and found that iPhone 5s, iPhone5c, and iPhone4s sizes differ than the defauly dimensions offered by InDesign. 
    Also, should I worry about the ppi resolution?  With iPhone, they all seem to be 326ppi but when dealing with other devices is this something that I should take into consideration?  Ideally, I could be creating DPS apps for all devices offered in the Digital Publishing drop down in InDesign (iPhone, iPad, Kindle Fire/Nook, and Android).
    Thank you for any help you can provide.
    By the way, if it helps I am using InDesign CC.

    Using 1024x768 and creating PDF articles will get you OK with both iPad resolutions, and, as Bob L. says, quite decent "one size fits all" result for all other devices.

  • How to set the display size of the PDF - in percent?

    Hi, I wonder if anyone knows if it is possible to set
    the display size of the PDF document, so that it always
    shows in, let´s say 100%, in the viewers browser window?
    Much grateful for any help!

    In Acrobat, under Document Properties (Ctrl+D), you can edit the Initial
    View settings, including the zoom level.

  • Display Size of the Visual Admininstrator

    I have an interesting problem - the display size of the Visual Administrator in one of my Netweaver systems has opened very small - I cannot stretch it any bigger. In all the rest of my systems the Visual Admininstrator opens full screen (we are AIX-UNIX).
    I think I can probably solve the problem by rebooting the server but I would like to know if there is any way to control the size of the Visual Admininstrator? Is there a configuration file or something similar?

    Hello Patrick ,
    I have no idea how to resize the visual admin.
    But the easiest thing to do is to install the visiual admin locally on a windows desktop.
    Be shure you have installed jre 1.4.2 on your windows desktop.
    Then copy the complete /usr/sap/<SID>/DVEBMGSXX/j2ee/admin
    directory to your windows desktop.
    Just doubleclick on the go.bat and the visual admin starts.
    Create the desired connections and youre finished.
    Have fun,

  • Can anyone tell me the dimensions of the 27" iMac without the stand?

    I am looking for the dimension of the 27" iMac, without the stand. The tech specs show dimensions with the stand.
    Thank you,

    My iMac screen is slightly over 17 1/2" high.  I have no idea whether the dimensions on the new one will be different.

  • How can you change the display size on the task bar

    how do you change the display size on the task bar

    If, however, you want to change the size of the display of the menubar, meaning make the icons and text larger, there is no way to do that directly other than to change the resolution of the screen.
    You can change the as-viewed size of that temporarily by using either -
    • Mouse zoom - if you have a Magic Mouse (Apple wireless mouse), hold down the Control key and use the scroll up and scroll down finger gestures on the mouse.
    • Zoom - go to System Preferences > Universal Access > Seeing and turn on Zoom. You can also use the noted keyboard shortcut to enable/disable this Zoom feature.

  • What is the display size ( without Stand )

    I want to put a Thunderbolt Display on a wall, with a VESA kit.
    What is the exact display size ? I'll remove the stand.

    Very likely it is a duplicate.  Use Get Info to see the source details for both tracks and/or use "show in Finder" to see if they trace back to the same file.  If there's two files then it is a true duplicate. If they go back to the same file then iTunes has mistakenly added a second reference.
    If it is mistaken reference you can probably delete it but I am not sure how to do this in your case since I set iTunes to manage my music in a different way. You have to be careful because iTunes default is set up to sometimes delete the file when you delete a track reference. If it is two references to the same file you don't want to delete the file itself.
    If they are two different files then you can decide which one to keep (usually the better quality one).

  • Is It Possible To Enlarge Thumbnail Display Size Without Enlarging Text On Firefox Window?

    Would Like To Enlarge Default Display Size Of Thumbnails, Without Enlarging Text Display.
    View Menu Allows Screen Component Enlargement But Text Size Becomes Prohibitive.

    prefabsoft wrote:
    Wow, thanks a lot for the fast reply. I don't mind doing it myself as I guess this laptop is much easier to disassemble compared to my previous one (being a 13" sony vaio). Mind if I ask how you know about this? Perhaps you have alread gone through the procedure?
    If it might be quite tricky I guess I can always ask a retailer.
    And really, thanks heaps mr.!! Appreciate your reply a whole lot!
    Best wishes,
    You're welcome. You can find more information on:
    I am a W701 user.

  • HT201263 I purchased an 1gen 16GB Ipod from a seller. The ipod only shows the connect to itunes logo when connected to computer. The display shows without the word itunes. I got error codes 1603 and 1604 and have followed all the steps that were shown on

    I purchased a 16gb ipod touch 1 gen and it wont restore or show the battery chaging icon. It shows the symbol of usb cable and what appears to be an itunes symbol without the itunes words being displayed. Upon trying to restore I have gotten error codes 1603 & 1604. I referred to the apple website for assistance and followed the steps to the letter with no results. So what else should I try or could I try because I have has no such luch thus far? I have held the home button and power button I tried to enter DFU mode but unsuccessful due to the screen boots with apple logo then immediately goes to the itunes screen and no further only when connected. Will not power on without usb connection have charged battery to see if it was the issue and no battery bar locator displays with or without being connected to PC.

    So you did all this:
    Error 1603: If you receive this error and the iOS device is not automatically placed into recovery mode, it may be necessary to do so manually. Refer to iPhone and iPod touch: Unable to restore for steps on placing iPhone into forced recovery mode. Also, remove the IPSW and attempt to restore again. If you do not want to remove the IPSW in the original user, try restoring in a new administrator user.
    Error 1604: This error is often related to USB timing. Try changing USB ports, uninstalling and reinstalling USB ports, and other available USB troubleshooting steps (troubleshooting USB connections, device not recognized properly, computer won't recognize a FireWire or USB device). If you are using a dock, bypass it and connect directly to the white Apple USB dock connector cable. If the issue persists on a known-good computer, the device may need service.
    If the issue is not resolved by USB isolation troubleshooting, and another computer is not available, try these steps to resolve the issue:
    Connect the device to iTunes, confirm that the device is in Recovery Mode. If it's not in Recovery Mode,put it into Recovery Mode.
    Restore and wait for error 1604.
    When prompted, click OK.
    Close and reopen iTunes while iPhone remains connected.
    iPhone should now be recognized in Recovery Mode again.
    Try to restore again.
    If the steps above do not resolve the issue, try restoring using a known-good USB cable, computer, and network connection.
    Did you try the last paragraph too?

  • 24" LED display: height without attached stand?

    I'm interested in the height of the 24" LED display, not including the attached stand. I'm considering this display for a confined space, using the optional VESA mounting adapter and a wall-mount.
    Apple lists the height of the display as 18.84" but I suspect that includes the stand.
    Would anyone with this display mind measuring its height, not including the stand?

    Excellent - thank you!
    I ended up calling Apple's online store people. They didn't have specs on file, so they found one to measure and gave me an "about 15 inches" measurement as relayed to the person on the phone. So it's good to get a real number from a real customer.
    One interesting tidbit is they said it vents in from the bottom and out from the top, so to be careful with mounting. Shouldn't be a problem here but good to know.
    Thanks again.

  • Displaying currentState without the _ character

    I have a state called Data_Drilldown and if I use {currentState} in a text label it will return the state exactly as it is but I want to eliminate the underscore character. How do I display the current state of an application so it appears w/o the underscore character?

    Having the same problem and looking for fix...

  • IMac 27" screen size without Stand

    Hi there, well I just wanna know the actual size without the stand, the size that appears on the site are with the stand, and I need to know the size without it since I´m going to place the iMac in a Vesa Mount, it would be great if someone can provide the Height and depth (the Width will be exactly the same)
    Thanx in advance

    I was wondering the same thing and went to the tech specs page. The graphic at the top showing an iMac from the back has dimensions indicating that the listed height -- 20.4 inches (51.7 cm)-- does NOT include the stand. Odd that there seems to be no measurement of overall height (including stand).
    My problem was slightly different. I was trying to figure out if the 27" iMac (and stand) would fit into the cubbyhole above my work desk. I measured the wife's 24" iMac stand and it added 6 cm to the total height. I added that to the 51.7 cm of the 27" iMac and found that the iMac would fit by lowering a shelf, but then I wouldn't be able to close the keyboard drawer -- logitech mouse would catch the bottom of the shelf. But if I removed the stand and mounted the 27" iMac on a Vesa Mount, everything would fit!

  • How to keep display size the same on second or more crop

    If you crop for a second time, or more, the display returns to the entire original image with the part cropped greyed out. I would like to be able to crop a second or more time using the display size of the first crop only. Is this possible? This would be particularly helpful with heavy crops.

    I see what you mean, but there's no way to get LR to do that for you. You could put in a feature request at the official site:

  • The weight of a 27" iMac without the aluminum stand.

    Hey there,
    do you know the (approximate) weight of an iMac 27" Quad Core without its aluminum stand?
    I REALLY need this information, thanks!

    27-inch iMac
    20.4 inches (51.7 cm)
    25.6 inches (65.0 cm)
    8.15 inches (20.7 cm)
    30.5 pounds (13.8 kg)1
    From here: http://www.apple.com/imac/specs.html
    No idea what it weighs without the stand but I wouldn't imagine the stand is more than 1lb, 2lbs at the most.

Maybe you are looking for

  • How use parameters on a html region for report query region

    Hi all. I have created a number of report regions which initially query some data. The requeriment now is to have a date range (initial and final) and use this range as a parameter for report queries. i created a new region containing these two date

  • Essbase 9.3.x for Linux

    HI All ! I need installation files for Essbase 9.3.x for Linux. Essbase,EAS,APS <email address removed by moderator so that you won't get spammed for all Eternity>

  • Can we create a Materialized View with Parameters?

    Experts, Can we create a materialized view by passing parameters to it. so that we change its value dynamically. If yes, plese provide me the eample also. Regards ND

  • Error "Cannot join tables. Item dependency 'TatZ' not found in EUL"

    I have created a Discoverer Report in a development instance of Oracle. After I create the Data views and Item classes in my production instance (using the same names) I attempt to run the report. I then get the error stated in the subject and the re

  • X-Fi Fatal1ty - Digital Out questions

    Hey everyone, I've done a bit of reading on this, but I'm still confused. First, some background. I've been looking for a small speaker solution where I don't have to run speakers to the back of my office. I've decided to go with the Pioneer HTS-GS -