1142N Mounting Position
Quick question about a survey I did yesterday. walked in and noticed that all the access points were wall mounted about 2 feet off the ground. The coverage wasn't bad, but I recommended they relocate the APs, to the ceiling as well as well as a few other things. Checking online I've noticed differing opinions about relocating the access points with some people saying since they are omni-directional orientation doesn't matter, but I would still believe mounting it so close to an obstruction would be an issue?
Hi David,
This is a topic that confused me and I spent a while pondering myself. From what I can determine, whilst the 1142/3502/3602 etc APs with internal radios are "omnidirectional" (360 degrees) it is only on the horizontal plane whilst on the vertical plane it is 180 degrees. This means that should you have the AP mounted on a wall it will be sending out a signal in a 360 degree pattern across floors above/below it and will have a strong signal in front of it but not as much behind (there will still be RF bleed and coverage behind due to reflection of radio waves etc).
If the AP is mounted on the ceiling, the signal will push out on a 360 degree range in what is best described as a donut pattern so imagine that the AP is at the center of a giant donut that expands outwards as the power increases. This will result in less cross-floor interference and provide more efficient coverage across each area (unless there's a specific need for wall mounted APs).
One option to save money on re-cabling all your areas is to install right angle mounting brackets on the walls to mimic ceiling placement:
http://www.oberonwireless.com/hard-lid_wall-mounted-access-point-enclosures.php
Hope that helps .
Ric
Similar Messages
-
Upgrade from 9i to 10g (DBUA problem)
The database instance running on my server doesnt show up in the Database upgrade Assistant screen to be selected for upgrade.
The instance is running and I am able to access it using SQL plus.
Before the upgrade I had upgraded the OS from Windows NT to Windows 2003
Should I proceed with a manual upgrade in this case
DilipHi Stefan,Joe
I managed to run the DBUA woithout any problem .
I left the upgrade process running and came back to check .I tried to start the database with 10g.
I was able to mount database but open database was failing.
I ran the sqlplus while db was in mount position.
sql>select version from V$instnace
10.2.0.2.0
but the alert log file was giving the error
ORA-00704: bootstrap process failure
ORA-39700: database must be opened with UPGRADE option
I started the database with sql
startup upgrade and ran below sql.
SQL> startup upgrade
ORACLE instance started.
Total System Global Area 616562688 bytes
Fixed Size 2052200 bytes
Variable Size 562040728 bytes
Database Buffers 50331648 bytes
Redo Buffers 2138112 bytes
Database mounted.
Database opened.
SQL> SQL> select comp_id, version ,status from dba_registry;
COMP_ID VERSION STATUS
CATALOG 9.2.0.4.0 VALID
CATPROC 9.2.0.4.0 VALID
SQL> select version from V$INSTANCE;
VERSION
10.2.0.2.0
SQL>
It is showing the db as desired but the
COMP_ID VERSION STATUS
CATALOG 9.2.0.4.0 VALID
CATPROC 9.2.0.4.0 VALID
How to correct the catalog and cataproc version to 10.2.0.2.0?
do i need to do something after that.
Let me know please.
Regards
Amit -
My IPod won't accept my verified AppleID, what do I do?
I am very new to Apple products (Aside from using Macs in ), and just got my first Ipod yesterday. I started my AppleID with my email address like anyone else and verified it. Briefly though, today I switched it to another email address I have. Finally deciding against it, I decided to switch back to the original email address I had used when I got it yesterday. But when I switched it, Itunes kept asking me to verify my AppleID through the original email. I had already done this when I started my account, so I could not do it again. Now I can't buy or download anything because my ITunes or my IPod keeps demanding I verify something that has been previously been verified. What can I do? I can download stuff on my computer through ITunes, but it doesn't work on my IPod. This *****...
The drive is not grabbing the discs?
Is the drive just not letting you insert the discs?
There is one thing you can try before going the external drive direction.
The first thing that I would attempt is to reset the optical drive’s eject mechanism. To do this, you’ll need to connect a wired, USB mouse to your computer. Then, tell your iMac to shut down. Once the machine is powered off, hold your mouse button down and re-power your iMac.
Keep the mouse button held down until you reach the login window. You should hear the optical drive perform one full eject cycle. At that point, you can release the mouse button, log in, and try insert a disk in the drive.
If this doesn't work, the cost of repairing the original drive maybe comparable or, most likely, more expensive to repair than just adding an external optical drive. And there is no guarantee that the internal optical drive won't fail, again, as the slot loading drives in iMacs have a tendency toward premature failure. It is not a very good drive to begin with and optical drives don't really like being mounted in a upright, vertical mounting position.
With external optical drives, there are many price and quality levels. You can purchase a cheap drive knowing that in less than a couple of years, it could fail and need a new replacement OR purchase a more expensive , but better quality drive that is more durable and designed to last longer. -
Hi,
Database is Oracle 8.1.7.4 about Windows NT.
I have a temporary tablespace with a datafile wich take more than 2Go.
I would like to create another temp tablespace locally managed with a tempfile to replace the first.
When I drop the old temp tablespace (with a datafile) this take more than 30 minutes, and I didn't wait more, I killed this session.
Why this one take to many time ? How can I make to make this quickly ?
Nicolas.To run your database you need one temporary tablespace available and the method which you can use is that first create a temporary tablespace first and then make it your default temporary tablespace bounce your database in mount position and then make your newly created tablespace your default temporary tablespace and then open the database and drop the old one.
-
as per my previous question, i installed an 80GB harddrive in my G3 tower. i then erased the original 4GB harddrive and had intentions of using it as simple storage. it order to do this easily, i unplugged the cd drive (not the power, the other cable), connected the old harddrive and erased it, all was well. when i adheard the 4GB drive in place, and reattacted the cd drive, i no longer see the 4GB drive. whenever i unplug the cd drive i am able to see the harddrive, what the heck is going on?! (i also have a floppy drive in the computer, both drives need to stay)
iMac G4 flat screen 800Mhz Mac OS X (10.4.3)You didn't indicate the type of beige G3 that you have - desktop or mini-tower. If the latter, you can easily connect two hard drives in a master/slave configuration to the same ribbon cable if:
(1) The ROM version is $77D45F1 (Rev. B) or $77D45F2 (Rev. C). Using the Apple System Profiler, scroll down to Production information, and the ROM version will be listed. If it's $77D40F2, you have a Rev. A ROM that doesn't support dual drives on a single ATA channel.
(2) The two drives are configured correctly, with one being "master" and the other "slave." This is done with small jumpers, that plug into the drive's configuration pins in a specific manner, which varies from one manufacturer to another.
You undoubtedly left the 4 GB drive with its factory-configuration of master. If it's connected to the same ribbon cable as the new hard drive or the optical drive, only one device can be set as master and one as slave. The CD-ROM drive is factory-configured as master, so if the 4 GB drive is connected to the same ribbon cable, then change its configuration to "slave." With both set as master, the hard drive will not be recognized when the optical drive is connected. When the optical drive is disconnected, the hard drive will be recognized. Hopefully, you have connected/disconnected the drives with the computer powered OFF.
If you have the desktop G3, remove the hard drive from the floor-mounted position and install both hard drives in the two bays, beside the optical drive. This would involve eliminating the Zip drive, if your G3 has one. There is no feasible way to connect two hard drives to the same ATA channel, with one mounted on the chassis floor and the other in the upper drive bay. The physical separation between the two drives and the cable length needed to connect both of them, causes too much data corruption. -
I have experienced this problem intermittently in the past, but now things seem to be really stuck. I go to Mail and open a new Note. In the past, when I was finished I would hit the "Done" button and the note would appear in my "Notes" box under "Reminders". Right now when I try this I get the message "Error. This Note could not be saved."
Beginning in the fall I started having a problem with the program creating "extra" intermediate notes under the same name throughout the day. I also started experiencing Notes disappearing totally after hitting the "Done" button. Sometimes they would show up in strange places in various "Mail" in/out/trash boxes. Sometimes I even found them on my iPhone in my AOL inbox.
I would really appreciate any thoughts as I've been using this as my primary note taking tool.
Thanks, BrianWhile you might have damaged the drive, but because of how they are vertically mounted in the iMac and maybe some heat related issue, the drive could've simply just failed. Its time has come.
Tthe internal optical drives in the aluminum style iMacs because of there mounting position seem to be prone to failure.
Your AppleCare has long since expired.
You have two options. You can pay to have the drive removed and replaced with a new internal drive and risk another premature failure. At least your iMac will have a brand new internal optical drive.
OR forget about the internal drive and look for and purchase an external third party optical drive that will be much better built and last longer and you can use this drive again when and if you decide to upgrade to a newer Mac or iMac model.
Another note. If you decide to have an Apple tech replace the internal optical drive, you might ask if possible, how much to install a larger hard drive into this iMac since they have to tear down the entire iMac anyhow.
Good Luck on whichever decision you choose -
My SuperDrive on my iMac won't load any typre of DVD or CD and is shaded,How about a fix?
SO when I try to load a DVD or CD in the slot on the side, my SuperDrive just ejects the disc. Any fixes out there. I notice that the SuperDrive is shaded in the about my Mac.
You could try a commercially or retail available CD/DVD dry brush lens cleaning disc to see if this revives the drive.
If not, It maybe your internal optical drive is dead.
This is a common occurrence in iMacs. The optical drive is, usually,,the first piece of hardware to fail.
Optical drives don't work very well in the vertical mounted position. That ans the heat inside the iMac are, usually, the cause of a failed SuperDrive in iMacs.
You can either pay to have the internal optical replaced, or purchase an external optical drive plugged into your iMac.These come in a lot of price and quality levels.
iMHO, the more expensive and durable tray loading drives have much better quality and longevity than slot-loading optical drives. You'll have to decide yourself what you want to use ii you go with using an external drives.
Some users buy cheap external optical drives,,knowing in a year or two they will have to replace it. Others, like myself, would rather spend more money on a more durable drive that will last longer than a year or two with regular use.
I'll leave these decisions to you. -
Hello Friends,
Is there anyway to rebuild the mirrlogA and B? If yes plz tell me the complete procedure to do this. We have lost this folder due to some serious problem in our SAP Server. We are using ECC 6.0/Oracle 10G/Win2003 platform. Plz help me...
thanks & regards,
VikramHi Vikram
As you say that u have lose the folder then follow the following steps
1.Bring the database in mount position
and execute first this cmd
2.alter database drop logfile group(Number);
3.alter database add logfile group 11
('/oracle/<SID>/origlogA/log_g11_m1.dbf',
'/oracle/<SID>/mirrlogA/log_g11_m2.dbf') size 50M;
4. open database with resetlogs
please let me know regarding any quary
cheer
Paresh -
Cannot read discs, help please?
Hi, any suggestions would be wonderful, but this is the current case:
I have an iMac that I purchased back in 2007. Literally, I just installed snow leopard a week ago, and the next time I inserted a disc into my drive - the disc got stuck. And this was very bad of me, but I took a card and gently jimmied the disc till it came out. I have never had this problem till I installed snow leopard onto it. So now whenever I put a disc in - it doesn't mount, and I hear the drives trying to read the disc, but it only spits out the disc after thirty seconds or so. Also, I have tried many different discs, and it is all the same case. They are all spit out. Help please? Should I just take it into the Apple Store?While you might have damaged the drive, but because of how they are vertically mounted in the iMac and maybe some heat related issue, the drive could've simply just failed. Its time has come.
Tthe internal optical drives in the aluminum style iMacs because of there mounting position seem to be prone to failure.
Your AppleCare has long since expired.
You have two options. You can pay to have the drive removed and replaced with a new internal drive and risk another premature failure. At least your iMac will have a brand new internal optical drive.
OR forget about the internal drive and look for and purchase an external third party optical drive that will be much better built and last longer and you can use this drive again when and if you decide to upgrade to a newer Mac or iMac model.
Another note. If you decide to have an Apple tech replace the internal optical drive, you might ask if possible, how much to install a larger hard drive into this iMac since they have to tear down the entire iMac anyhow.
Good Luck on whichever decision you choose -
As a new owner I quickly realised the F210 mounting is fairly hopeless and rather insecure. All videos are recorded in excellent quality complete with continuous vibration.
My question is can the video be recorded upside down. What I mean is can I mount the camera using a different system which may end up with the camera upside down to normal. Some cameras allow this to happen and just record correctly regardless of the mounting position. IE. turn the camera 180 degrees and the picture turns with it like an iphone.
There should be a setting somewhere but I cant find it.
Other wise the camera seems quite good. Just the mounting is crap.I found a few at Costco and Amazon:
http://www.costco.com/HP-Dash-Camera-by-Rear-View-Safety.product.100082955.html
http://www.amazon.com/HP-F210-DashBoard-Accident-Recorder/dp/B00EEHN7BO
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others** -
Removing the vesa mount - unlock the stand position?
I'm taking my iMac back to the apple store to get an issue with the display fixed (smudging in the top corners - grr) but first I need to remove my vesa mount and put the original stand back on so I can take it to my appointment.
I have got the original stand back on, but the mount is still in the extended, locked position. Does anyone know how I unlock the position of the bracket so that my iMac no longer faces down at my desk and it's position (angle) is free to be adjusted by hand once again?
Cheers,ah, found the link below (why is it often so difficult to find things on these forums?) - it really is just a matter of pushing in and down with the card to press the latch (which you can just about see above the bracket) until you here a click and then all is well again.
Probably would of been good for apple to put those instructions in the manual that came with the bracket...
Removing the bracket:
https://discussions.apple.com/thread/2251637?threadID=2251637 -
Antenna position when mounting on wall (WRT1900AC)
The user guide recommends how to position the antennas when the router is sitting on a shelf, but I would like to get some advice for antenna possitioning when mounting the unit on a wall.
Thank you.
michaelIn this case you don't want to locate it in the basement.
Locate the router on the main floor preferably in a window open to the back yard. Exterior wall material such as Stucco or metal siding will require using a windows because of the metal or mesh.
Please remember to Kudo those that help you.
Linksys
Communities Technical Support -
K7T26 Pro2A Mounting Hole Positions
I know this may sound silly but can somebody please tell me if, when installing this motherboard, you only use the six mounting holes on the board (the ones with the silver ring around them). 6 doesnt seem many and it seems to me that the EIDE connections are not supported. I've looked on upteen web sites and in the manual but all it says is there are 6 holes. There are some more holes but they seem small and do not match any holes in my case.
If it says there are 6, thats all you get.
-
Can I prevent mounted volume Finder windows opening on startup?
I look after a studio with about 10 Macs, some of which are running OSX 10.4.11. We automatically mount 3 network volumes containing client data at startup. The Finder always opens a window for each volume but I want to prevent this from happening.
In Finder preferences I can prevent the volume icons from appearing on the desktop but the Finder still opens a window for each one at startup when the volumes are mounted..
How can I control this action?This is a hack, but you can try to use xtool to close the windows. I place the following script in my login items. You may want to put in a delay of some sort.
You may also try iKey.
I use iKey to remap the keys. It has a little more function then youpi key. For many years, I used youpi key before switching to iKey.
You might like iKey/youpi key. I have my frequently used applications set to f keys. The same f key starts an application and switches to the application.
Youpi key is free. It works fairly well for me in MAC OS 10.4 although not officially supported. There is a commercial version you can buy, called iKey.
http://www.versiontracker.com/dyn/moreinfo/macosx/11485&vid=75326
This applescript could use some clean up. I do not think you need the first two lines.
do shell script "/usr/sbin/system_profiler SPDisplaysDataType | grep 'Resolution'" -- get info
tell the result to set {DisplayWidth, DisplayHeight} to {word 2, word 4} -- get resolution
--move mouse {DisplayWidth div 2, DisplayHeight div 2} -- center mouse
move mouse {670, 13} --sound
click mouse
move mouse {673, 96} --sound level
click mouse
move mouse {555, 282} -- center mouse
click mouse
First, there is the XTools scripting addition, which will give AppleScript the ability to move the mouse.
http://www.lestang.org/osax/XTool/
XTool-2.0-src.dmg.tgz
Installation :
Drag XTool.osax from insite the image to one of the following locations (create the directory if it does not exist) :
a : ~/Library/ScriptingAdditions/
b : /Library/ScriptingAdditions/
c : /System/Library/ScriptingAdditions/
I have it in directory /System/Library/ScriptingAdditions/
My other two directories do not exit: ~/Library/ScriptingAdditions/ &
/Library/ScriptingAdditions/
. Next, you will need to place a script application into your login items (System Preferences > Accounts > Login Items) that will move the mouse when you log in:
This script will give you the location of the pointer. I assigned it to a function key with iKey. So, place the cursor of the x then press the function key to get where you need to click.
do shell script "/usr/sbin/system_profiler SPDisplaysDataType | grep 'Resolution'" -- get info
tell the result to set {DisplayWidth, DisplayHeight} to {word 2, word 4} -- get resolution
set {xWidth, yHeight} to position of the mouse
display dialog ¬
"DisplayWidth= " & DisplayWidth & ¬
" DisplayHeight=" & DisplayHeight & return & ¬
" xWidth=" & xWidth & ¬
" yHeight=" & yHeight
--move mouse {DisplayWidth div 2, DisplayHeight div 2} -- center mouse
You could try sending command + w to the finder. You can get the idea ... See this example, some work needed by reader!!!:
on open dropped_items
-- Write a message into the event log.
log " --- Starting on " & ((current date) as string) & " --- "
-- set see to alias "Macintosh-HD:Users:mac:Desktop:app.html"
-- set dropped_items to {see}
set the_app to "Safari"
repeat with dropped_item_ref in dropped_items
--set UrlBase to "xzzx FILE://" & POSIX path of dropped_item_ref
--display dialog UrlBase
-- Activate
activate application the_app
-- Open the URL
tell application the_app
open dropped_item_ref
-- print dropped_item_ref
tell application "System Events"
tell process the_app
delay 3
-- click menu item "Print..." of menu "File" of menu bar 1
keystroke "p" using command down
delay 1
keystroke return
delay 10
keystroke "w" using command down
end tell
end tell
--quit
end tell
end repeat
end open
Message was edited by: rccharles -
Is it possible to mount a physical disk (/dev/mapper/ disk) on one of my Oracle VM server
I have a physical disk that I can see from multipath -ll that shows up as such
# multipath -ll
3600c0ff00012f4878be35c5401000000 dm-115 HP,P2000G3 FC/iSCSI
size=410G features='1 queue_if_no_path' hwhandler='0' wp=rw
|-+- policy='round-robin 0' prio=50 status=active
| `- 7:0:0:49 sdcs 70:0 active ready running
`-+- policy='round-robin 0' prio=10 status=enabled
`- 10:0:0:49 sdcr 69:240 active ready running
That particular is visible in the OVMM Gui as a physical disk that I can present to one of my VMs but currently its not presented to any of them.
I have about 50 physical LUNs that my Oracle VM server can see. I believe I can see all of them from a fdisk -l, but "dm-115" (which is from the multipath above) doesnt show up.
This disk has 3 usable partitions on it, plus a Swap.
I want to mount the 3rd partition temporarily on the OVM server itself and I receive
# mount /dev/mapper/3600c0ff00012f4878be35c5401000000p3 /mnt
mount: you must specify the filesystem type
If I present the disk to a VM and then try to mount the /dev/xvdx3 partition -it of course works. (x3 - represents the 3rd partition on what ever letter position the disk shows up as)
Is this possible?Its more of the correct syntax. Like I can not seem to figure out how to translate the /dev/mapper path above into what fdisk -l shows. Perhaps if I knew how fdisk and multipath can be cross referenced I could mount the partition.
I had already tried what you suggested. Here is the output if I present the disk to a VM and then mount the 3rd partition.
# fdisk -l
Disk /dev/xvdh: 439.9 GB, 439999987712 bytes
255 heads, 63 sectors/track, 53493 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/xvdh1 * 1 13 104391 83 Linux
/dev/xvdh2 14 2102 16779892+ 82 Linux swap / Solaris
/dev/xvdh3 2103 27783 206282632+ 83 Linux
/dev/xvdh4 27784 30394 20972857+ 5 Extended
/dev/xvdh5 27784 30394 20972826 83 Linux
# mount /dev/xvdh3 /mnt <-- no error
# df -h
Filesystem Size Used Avail Use% Mounted on
/dev/xvda3 197G 112G 75G 60% /
/dev/xvda5 20G 1011M 18G 6% /var
/dev/xvda1 99M 32M 63M 34% /boot
tmpfs 2.0G 0 2.0G 0% /dev/shm
/dev/xvdh3 191G 58G 124G 32% /mnt <-- mounted just fine
Its ext3 partition
# df -T
/dev/xvdh3
ext3 199822096 60465024 129042944 32% /mnt
Now if I go to my vm.cfg file, I can see the disk that is presented.
My disk line contains
disk = [...'phy:/dev/mapper/3600c0ff00012f4878be35c5401000000,xvdh,w', ...]
Multipath shows that disk and says "dm-115" but that does not translate on fdisk
# multipath -ll
3600c0ff00012f4878be35c5401000000 dm-115 HP,P2000G3 FC/iSCSI
size=410G features='1 queue_if_no_path' hwhandler='0' wp=rw
|-+- policy='round-robin 0' prio=50 status=active
| `- 7:0:0:49 sdcs 70:0 active ready running
`-+- policy='round-robin 0' prio=10 status=enabled
`- 10:0:0:49 sdcr 69:240 active ready running
I have around 50 disks on this server, but the ones of the same size from fdisk -l from the server shows me many.
# fdisk -l
Disk /dev/sdp: 439.9 GB, 439999987712 bytes
255 heads, 63 sectors/track, 53493 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sdp1 * 1 13 104391 83 Linux
/dev/sdp2 14 2102 16779892+ 82 Linux swap / Solaris
/dev/sdp3 2103 27783 206282632+ 83 Linux
/dev/sdp4 27784 30394 20972857+ 5 Extended
/dev/sdp5 27784 30394 20972826 83 Linux
Disk /dev/sdab: 439.9 GB, 439956406272 bytes
255 heads, 63 sectors/track, 53488 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sdab1 * 1 13 104391 83 Linux
/dev/sdab2 14 1318 10482412+ 82 Linux swap / Solaris
/dev/sdab3 1319 27783 212580112+ 83 Linux
/dev/sdab4 27784 30394 20972857+ 5 Extended
/dev/sdab5 27784 30394 20972826 83 Linux
Disk /dev/sdac: 439.9 GB, 439956406272 bytes
255 heads, 63 sectors/track, 53488 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sdac1 * 1 13 104391 83 Linux
/dev/sdac2 14 2102 16779892+ 82 Linux swap / Solaris
/dev/sdac3 2103 27783 206282632+ 83 Linux
/dev/sdac4 27784 30394 20972857+ 5 Extended
/dev/sdac5 27784 30394 20972826 83 Linux
Disk /dev/sdad: 439.9 GB, 439956406272 bytes
255 heads, 63 sectors/track, 53488 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sdad1 * 1 13 104391 83 Linux
/dev/sdad2 14 1318 10482412+ 82 Linux swap / Solaris
/dev/sdad3 1319 27783 212580112+ 83 Linux
/dev/sdad4 27784 30394 20972857+ 5 Extended
/dev/sdad5 27784 30394 20972826 83 Linux
Disk /dev/sdae: 439.9 GB, 439956406272 bytes
255 heads, 63 sectors/track, 53488 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sdae1 * 1 13 104391 83 Linux
/dev/sdae2 14 2102 16779892+ 82 Linux swap / Solaris
/dev/sdae3 2103 27783 206282632+ 83 Linux
/dev/sdae4 27784 30394 20972857+ 5 Extended
/dev/sdae5 27784 30394 20972826 83 Linux
Disk /dev/sdaf: 439.9 GB, 439999987712 bytes
255 heads, 63 sectors/track, 53493 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sdaf1 * 1 13 104391 83 Linux
/dev/sdaf2 14 2102 16779892+ 82 Linux swap / Solaris
/dev/sdaf3 2103 27783 206282632+ 83 Linux
/dev/sdaf4 27784 30394 20972857+ 5 Extended
/dev/sdaf5 27784 30394 20972826 83 Linux
Disk /dev/sdag: 439.9 GB, 439999987712 bytes
255 heads, 63 sectors/track, 53493 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sdag1 * 1 13 104391 83 Linux
/dev/sdag2 14 2102 16779892+ 82 Linux swap / Solaris
/dev/sdag3 2103 27783 206282632+ 83 Linux
/dev/sdag4 27784 30394 20972857+ 5 Extended
/dev/sdag5 27784 30394 20972826 83 Linux
Disk /dev/dm-13: 439.9 GB, 439999987712 bytes
255 heads, 63 sectors/track, 53493 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/dm-13p1 * 1 13 104391 83 Linux
/dev/dm-13p2 14 2102 16779892+ 82 Linux swap / Solaris
/dev/dm-13p3 2103 27783 206282632+ 83 Linux
/dev/dm-13p4 27784 30394 20972857+ 5 Extended
/dev/dm-13p5 27784 30394 20972826 83 Linux
Disk /dev/dm-25: 439.9 GB, 439956406272 bytes
255 heads, 63 sectors/track, 53488 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/dm-25p1 * 1 13 104391 83 Linux
/dev/dm-25p2 14 1318 10482412+ 82 Linux swap / Solaris
/dev/dm-25p3 1319 27783 212580112+ 83 Linux
/dev/dm-25p4 27784 30394 20972857+ 5 Extended
/dev/dm-25p5 27784 30394 20972826 83 Linux
Disk /dev/dm-26: 439.9 GB, 439956406272 bytes
255 heads, 63 sectors/track, 53488 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/dm-26p1 * 1 13 104391 83 Linux
/dev/dm-26p2 14 2102 16779892+ 82 Linux swap / Solaris
/dev/dm-26p3 2103 27783 206282632+ 83 Linux
/dev/dm-26p4 27784 30394 20972857+ 5 Extended
/dev/dm-26p5 27784 30394 20972826 83 Linux
Disk /dev/dm-27: 439.9 GB, 439956406272 bytes
255 heads, 63 sectors/track, 53488 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/dm-27p1 * 1 13 104391 83 Linux
/dev/dm-27p2 14 1318 10482412+ 82 Linux swap / Solaris
/dev/dm-27p3 1319 27783 212580112+ 83 Linux
/dev/dm-27p4 27784 30394 20972857+ 5 Extended
/dev/dm-27p5 27784 30394 20972826 83 Linux
Disk /dev/dm-28: 439.9 GB, 439956406272 bytes
255 heads, 63 sectors/track, 53488 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/dm-28p1 * 1 13 104391 83 Linux
/dev/dm-28p2 14 2102 16779892+ 82 Linux swap / Solaris
/dev/dm-28p3 2103 27783 206282632+ 83 Linux
/dev/dm-28p4 27784 30394 20972857+ 5 Extended
/dev/dm-28p5 27784 30394 20972826 83 Linux
Disk /dev/dm-29: 439.9 GB, 439999987712 bytes
255 heads, 63 sectors/track, 53493 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/dm-29p1 * 1 13 104391 83 Linux
/dev/dm-29p2 14 2102 16779892+ 82 Linux swap / Solaris
/dev/dm-29p3 2103 27783 206282632+ 83 Linux
/dev/dm-29p4 27784 30394 20972857+ 5 Extended
/dev/dm-29p5 27784 30394 20972826 83 Linux
Disk /dev/dm-30: 439.9 GB, 439999987712 bytes
255 heads, 63 sectors/track, 53493 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/dm-30p1 * 1 13 104391 83 Linux
/dev/dm-30p2 14 2102 16779892+ 82 Linux swap / Solaris
/dev/dm-30p3 2103 27783 206282632+ 83 Linux
/dev/dm-30p4 27784 30394 20972857+ 5 Extended
/dev/dm-30p5 27784 30394 20972826 83 Linux
How to translate the /dev/mapper address into the correct fdisk, I think I can then mount it.
If I try the same command as before with the -t option it gives me this error.
# mount -t ext3 /dev/mapper/3600c0ff00012f48791975b5401000000p3 /mnt
mount: special device /dev/mapper/3600c0ff00012f48791975b5401000000p3 does not exist
I know I am close here, and feel it should be possible, I am just missing something.
Thanks for any help
Maybe you are looking for
-
Open file in a new window thru custom global link
Hi All, I have created a custom global link. I want to open a PDF file (present at OA_HTML) from that link. So, I created a function for that link having below properties: Web HTML : file_name.pdf Type: SSWA plsql function that opens a new window (Ki
-
InDesign for Windows + Arabic and Nepali languages
Is it possible to create documents in Nepali and Arabic in InDesign CS3 for Windows? Any specific requirements?
-
Responsive (full)background Video
HI! I have a question is there any widget? that allows to create effect like here: CROP THE BLOCK | Creative filmmakers and videos from Paris and Berlin I mean the background video is link from vimeo/youtube and its RESPONSIVE thx for help!
-
Does any one know of software that you can import a PDF and then draw on it, dimensions, notes and symbols...technical drawing?. Blue beam have the perfect software for this BUT it's not Mac compatible
-
Misplaced thumbnails - duplicate tinyCacheIndex in property list
I'm one of the users who's been frustrated lately with the wrong thumbnail showing up at times (with Aperture 2.1 at present, but I saw this frequently with 2.0). I've tracked down what I think is the immediate source of the issue, though I haven't h