802.1x Vlan Assignment

I am planning to implement 802.1x on a 4506 switch. The issue that i have is i have 5 user Departmental vlan on the switch. How can i configure the ACS to assigned vlan for each of my user to their respected departmental vlan? please help

That can be done, it's called "Using 802.1X with VLAN Assignment". Here is a link on cat4000 on how to configure 802.1X with VLAN assignment:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/12_2_25a/conf/dot1x.htm#wp1142124
And here is a link on Using a RADIUS Server to Assign Users to VLANs:
http://www.cisco.com/univercd/cc/td/doc/product/wireless/airo1200/accsspts/b1237ja/i1237sc/s37vlan.htm#wp1038739
I hope this helps.

Similar Messages

NAC 802.1x: VLAN assignment via RADIUS

I'm deploy a 802.1x NAC solution. Users authenticate ok but the VLAN is not assigned to the port.
The RADIUS server send the attributes to the NAD (switch 3560). I see the following lines in the radius debug output:
02:49:08: RADIUS: Received from id 1645/4 192.168.1.1:1645, Access-Accept, len 267
02:49:08: RADIUS: authenticator AB 90 94 95 D0 86 04 E5 - D3 AC 43 21 C0 31 29 EB
02:49:08: RADIUS: Session-Timeout [27] 6 3600
02:49:08: RADIUS: Termination-Action [29] 6 1
02:49:08: RADIUS: Tunnel-Type [64] 6 01:Unsupported [13]
02:49:08: RADIUS: Tunnel-Medium-Type [65] 6 01:Unsupported [6]
02:49:08: RADIUS: Tunnel-Private-Group[81] 10 01:"healthy"
02:49:08: RADIUS: Vendor, Cisco [26] 29
02:49:08: RADIUS: Cisco AVpair [1] 23 "posture-token=Healthy"
I suppose that the error appears because the attributes 64 and 65 are "Unsupported". Is it right?
In RADIUS server I configure:
attribute 64 = VLAN (13)
attribute 65 = 802 (6)
Below I attach switch configuration. The "healthy" vlan is configured in this one.
Any help would be appreciated.
Thanks and regards.
Mart?n.

I change the IOS and all work fine. The IOS must have the feature "NAC - L2 IEEE 802.1x".
Other user has the same problem, he posted the question with the following subject: "NAC L2 802.1x VLAN assignment".In this question the problem is better described.

Assign building-specific VLAN via 802.1X vlan assignment

Hi all
We plan to implement 802.1X. We have several departments. Each department is using several VLANs, depending on which building the machine is.
If a machine/user from department A connects in building A, it should receive VLAN 10 via 802.1X vlan assignment. If the same machine/user connects in building B, it should receive VLAN 20.
Is this possible with 802.1X vlan assignment?
Many thanks
regards
Stefan

Stefan- It is possible if you use the VLAN name instead of the vlan #. That means you will just have to be consistent with your Vlan names for each location. So lets say you set up authenticated users to go to the "AuthUser" vlan. On your switches you would set up:
AuthUser=vlan 10 in Bldg A
AuthUser=vlan 20 in Bldg B
etc...
Just know that if someone unknowingly changes the vlan name on the switch that it will break dot1x, so make sure your fellow engineers know the significance of the name.
Good luck with your implementation!

802.1x VLAN assignment + Microsoft IAS

Hello,
Here is what I am tring to do:
a Windows XP client is authenticating via 802.1x to a cisco switch. The switch "talks" to a IAS radius serveur (microsoft). That works fine, the user can login and the port opens up. Cisco developed a feature in a recent software release whereby the radius server can also tell the switch what VLAN to place the freshly-authenticated port in (that's the part I can't get to work - the fact that I am totally new to Radius probably doesn't help either). I know that the switch expects the following parameters within the Access-accept:
a) Tunnel-Type(#64)=VLAN (13)
b) Tunnel-Medium-Type(#65)=802 (6)
c) Tunnel-Private-Group-ID(#81)=VLANID
How Can I define these parameters in IAS ? I tried severals things but know one worked. If someone has experience, please let me know .... Thanx !
Bastien

thanx for your answer.
Thanx for your answer.
I tried that but I think I made mistakes because it
doesn't work.
What I need to know is what I have to enter precisely :
- Which kind of attribute ? Cisco AVPAIR or radius vendor
specific attribute or something else ?
- Which value in the field : Tunnel-Type(#64) or just 64
or just Tunnel-Type or just #64 or 13 ?
- Which value in the field atttribute format ? string,
decimal or hexadecimal ?
Thanx very much !!

802.1X and automatic vlan assignment

Hello,
I'm testing a 802.1X infrastructure :
Switch : Try with Netgear Prosafe GS728TPS and Cisco SF300
Radius Server : Microsoft NPS
DHCP Relay for address assignement by Vlan
I have created some policies with simple authentication for testing (MSCHAP V2) and vlan assignement or not (depend on Active Directory Group).
All work fine on a Windows 7 Pro. The user 1 is authenticated whithout vlan and the user 2 is authenticated with a vlan.
The DHCP works fine and the 2 users have an IP.
When I try on MAC OS X (ver. 10.7.2 and ver. 10.9.2) the user 1 (whithout vlan) work fine. I have an IP and access to the LAN. But the user 2 (with vlan) don't work. The Mac don't get an IP and I'm not on the VLAN. If i push manually an IP of the vlan, I have no access to the VLAN.
There are some specifics parameters to add for enable vlan on Mac OS X ?
Thanks for reply
Ben

Edit : It's for wired connections

WLC 5508: 802.1 AAA override; Authenication success no dynamic vlan assignment

WLC 5508: software version 7.0.98.0
Windows 7 Client
Radius Server: Fedora Core 13 / Freeradius with LDAP storage backend
I have followed the guide at http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml with respective to building the LDAP and free radius server. 802.1x authorization and authenication correctly work. The session keys are returned from the radius server and the wlc send the appropriate information for the client to generate the WEP key.
However, the WLC does not override the VLAN assignment, even though I was to believe I set everything up correctly. From the packet capture, you can see that verfication of client is authorized to use the WLAN returns the needed attributes:
AVP: l=4 t=Tunnel-Private-Group-Id(81): 10
AVP: l=6 t=Tunnel-Medium-Type(65): IEEE-802(6)
AVP: l=6 t=Tunnel-Type(64): VLAN(13)
I attached a packet capture and wlc config, any guidance toward the attributes that may be missing or not set correctly in the config would be most appreciated.

Yes good catch, so I had one setting left off in freeradius that allowed the inner reply attributes back to the outer tunneled accept. I wrote up a medium high level config for any future viewers of this thread:
The following was tested and verified on a fedora 13 installation.   This is a minimal setup; not meant for a "live" network (security issues with cleartext passwords, ldap not indexed properly for performance)
Install Packages
1. Install needed packages.
yum install openldap*
yum install freeradius*
2. Set the services to automatically start of system startup
chkconfig --level 2345 slapd on
chkconfig --level 2345 radiusd on
Configure and start LDAP
1. Copy the needed ladp schemas for radius. Your path may vary a bit
cp /usr/share/doc/freeradius*/examples/openldap.schema /etc/openldap/schema/radius.schema
2. Create a admin password for slapd. Record this password for later use when configuring the slapd.conf file
slappasswd
3. Add the ldap user and group; if it doesn't exisit. Depending on the install rpm, it may have been created
useradd ldap
groupadd ldap
4. Create the directory and assign permissions for the database files
mkdir /var/lib/ldap
chmod 700 /var/lib/ldap
chown ldap:ldap /var/lib/ldap
5. Edit the slapd.conf file.
cd /etc/openldap
vi slapd.conf
# See slapd.conf(5) for details on configuration options.
# This file should NOT be world readable.
#Default needed schemas
include        /etc/openldap/schema/corba.schema
include        /etc/openldap/schema/core.schema
include        /etc/openldap/schema/cosine.schema
include        /etc/openldap/schema/duaconf.schema
include        /etc/openldap/schema/dyngroup.schema
include        /etc/openldap/schema/inetorgperson.schema
include        /etc/openldap/schema/java.schema
include        /etc/openldap/schema/misc.schema
include        /etc/openldap/schema/nis.schema
include        /etc/openldap/schema/openldap.schema
include        /etc/openldap/schema/ppolicy.schema
include        /etc/openldap/schema/collective.schema
#Radius include
include        /etc/openldap/schema/radius.schema
#Samba include
#include        /etc/openldap/schema/samba.schema
# Allow LDAPv2 client connections. This is NOT the default.
allow bind_v2
# Do not enable referrals until AFTER you have a working directory
# service AND an understanding of referrals.
#referral    ldap://root.openldap.org
pidfile        /var/run/openldap/slapd.pid
argsfile    /var/run/openldap/slapd.args
# ldbm and/or bdb database definitions
#Use the berkely database
database    bdb
#dn suffix, domain components read in order
suffix        "dc=cisco,dc=com"
checkpoint    1024 15
#root container node defined
rootdn        "cn=Manager,dc=cisco,dc=com"
# Cleartext passwords, especially for the rootdn, should
# be avoided. See slappasswd(8) and slapd.conf(5) for details.
# Use of strong authentication encouraged.
# rootpw        secret
rootpw
{SSHA}
cVV/4zKquR4IraFEU7NTG/PIESw8l4JI
# The database directory MUST exist prior to running slapd AND
# should only be accessible by the slapd and slap tools. (chown ldap:ldap)
# Mode 700 recommended.
directory    /var/lib/ldap
# Indices to maintain for this database
index objectClass                       eq,pres
index uid,memberUid                     eq,pres,sub
# enable monitoring
database monitor
# allow onlu rootdn to read the monitor
access to *
         by dn.exact="cn=Manager,dc=cisco,dc=com" read
         by * none
6. Remove the slapd.d directory
cd /etc/openldap
rm -rf slapd.d
7. Hopefully if everything is correct, should be able to start up slapd with no problem
service slapd start
8. Create the initial database in a text file called /tmp/initial.ldif
dn: dc=cisco,dc=com
objectClass: dcobject
objectClass: organization
o: cisco
dc: cisco
dn: ou=people,dc=cisco,dc=com
objectClass: organizationalunit
ou: people
description: people
dn: uid=jonatstr,ou=people,dc=cisco,dc=com
objectClass: top
objectClass: radiusprofile
objectClass: inetOrgPerson
cn: jonatstr
sn: jonatstr
uid: jonatstr
description: user Jonathan Strickland
radiusTunnelType: VLAN
radiusTunnelMediumType: 802
radiusTunnelPrivateGroupId: 10
userPassword: ggsg
9. Add the file to the database
ldapadd -h localhost -W -D "cn=Manager, dc=cisco,dc=com" -f /tmp/initial.ldif
10. Issue a basic query to the ldap db, makes sure that we can request and receive results back
ldapsearch -h localhost -W -D cn=Manager,dc=cisco,dc=com -b dc=cisco,dc=com -s sub "objectClass=*"
Configure and Start FreeRadius
1. Configure ldap.attrmap, if needed. This step is only needed if we need to map and pass attributes back to the authenicator (dynamic vlan assignments as an example). Below is an example for dynamic vlan addresses
cd /etc/raddb
vi ldap.attrmap
For dynamic vlan assignments, verify the follow lines exist:
replyItem    Tunnel-Type                                   radiusTunnelType
replyItem    Tunnel-Medium-Type                   radiusTunnelMediumType
replyItem    Tunnel-Private-Group-Id              radiusTunnelPrivateGroupId
Since we are planning to use the userpassword, we will let the mschap module perform the NT translations for us. Add the follow line to check ldap object for userpassword and store as Cleartext-Password:
checkItem    Cleartext-Password    userPassword
2. Configure eap.conf. The following sections attributes below should be verified. You may change other attributes as needed, they are just not covered in this document.
eap
{      default_eap_type = peap      ..... }
tls {
    #I will not go into details here as this is beyond scope of setting up freeradisu. The defaults will work, as freeradius comes with generated self signed certificates.
peap {
    default_eap_type = mschapv2
    #you will have to set this to allowed the inner tls tunnel attributes into the final accept message
    use_tunneled_reply = yes
3. Change the authenication and authorization modules and order.
cd /etc/raddb/sites-enabled
vi default
For the authorize section, uncomment the ldap module.
For the authenicate section, uncomment the ldap module
vi inner-tunnel
Very importants, for the authorize section, ensure the ldap module is first, before mschap. Thus authorize will look like:
authorize
{      ldap      mschap      ...... }
4. Configure ldap module
cd /etc/raddb/modules
ldap
{        server=localhost       identify = "cn=Manager,dc=cisco,dc=com"        password=admin       basedn="dc=cisco,dc=com"       base_filter = "(objectclass=radiusprofile)"       access_attr="uid"       ............   }
5. Start up radius in debug mode on another console
radiusd -X
6. radtest localhost 12 testing123
You should get a Access-Accept back
7. Now to perform an EAP-PEAP test. This will require a wpa_supplicant test libarary called eapol_test
First install openssl support libraries, required to compile
yum install openssl*
yum install gcc
wget http://hostap.epitest.fi/releases/wpa_supplicant-0.6.10.tar.gz
tar xvf wpa_supplicant-0.6.10.tar.gz
cd wpa_supplicant-0.6.10/wpa_supplicant
vi defconfig
Uncomment CONFIG_EAPOL_TEST = y and save/exit
cp defconfig .config
make eapol_test
cp eapol_test /usr/local/bin
chmod 755 /usr/local/bin/eapol_test
8. Create a test config file named eapol_test.conf.peap
network=
{   eap=PEAP eapol_flags=0 key_mgmt=IEEE8021X identity="jonatstr"   password="ggsg" \#If you want to verify the Server certificate the below would be needed   \#ca_cert="/root/ca.pem" phase2="auth=MSCAHPV2"   }
9. Run the test
eapol_test -c ~/eapol_test.conf.peap -a 127.0.0.1 -p 1812 -s testing123

802.1x RADIUS with EAP-TLS/EAP-TTLS & Dynamic VLAN Assignment

Hello, My team is looking for switches supporting 802.1x authentication on either EAP-TTLS or EAP-TLS protocols with dynamic vlan assignment enabled for these. Looking at the data sheets of the Linksys desktop switches, I found only SLM224G4PS and SLM224G4S models to support EAP-TLS or EAP-TTLS. Am I right? Do they support Dynamic VLAN Assigment for either of those protocols? This is not explicitly mentioned in the data sheets, and I happen to find switches from other manufacturers that announce to support EAP-TLS/EAP-TTLS but no dynamic vlan assignment. Thank you for any help.

SLM switches do support 802.1x RADIUS with EAP-TLS/EAP-TTLS unlike the SRW switches which support MD5. But I don't think that they support Dynamic VLAN.

802.1x with Vlan assignment and IP phone and PC

I have a Catalyst 4510R and I want to im plement 802.1x with dynamic VLAN assignment via Radius server. I am going to plug to switch ports Cisco IP phones and PCs (PCs are plugged in the IP phone).
For this implementation I need to configure the switch port in mode trunk because I have voice vlan corresponding IP phone and data vlan corresponding to PC.
However I have read that I can not enable 802.1x on a trunk port.
How could I configure this?
I need that when the PC is authenticated correctly is assigned to his cooresponding data vlan and the IP phone is in the voice vlan.
Thanks

You should configure the port as an access port with an aux-vlan. Here's an example:
interface GigabitEthernet2/2
switchport access vlan 701
switchport mode access
switchport voice vlan 702
load-interval 30
qos trust device cisco-phone
qos trust cos
auto qos voip cisco-phone
dot1x pae authenticator
dot1x port-control auto
tx-queue 3
bandwidth percent 33
priority high
shape percent 33
spanning-tree portfast
spanning-tree bpduguard enable
service-policy output autoqos-voip-policy
Hope this helps,

802.1X for wired environments using Radius/ACS for Dynamic Vlan Assignment

Currently Being Moderated
802.1X for wired environments using Radius/ACS for Dynamic Vlan Assignment
Could someone please provide me with a simplest set of configuration steps to fire up Radius in ACS and 802.1X for dynamic vlan assignment. The objective is to roll out NAC L2 OOB using the 802.1X method for dymamic vlan assignments.
If possible show:
1. ACS/Radius Configurations.
2. End User Switch Configurations
Variables:
Switch A
MAC Address aaaa.bbbb.cccc     Vlan 10
            bbbb.cccc.dddd     Vlan 20
Also, if someone posts the Pros and Cons of using Radius/ACS/802.1X for Dynamic Vlan Assignments.
Other technology sets that can be used for Dynamic Vlan assignment EXCEPT from deprecated/obsolete VMPS.
Thanks in advance. .

Hi Guys,
    Hmmm, well if your just looking for Mac based authentication the good news is that is very easy. Just set create your Radius server, ACS, FreeRadius, Steelbelted radius etc. Then create user with the name of the Mac address, in other words if the mac address is 0012.0021.1122 the the name would be 001200211122 and the password would be the mac address. Then you set the vlan and tunnel stuff, like so tunnel-Type would be vlan, Tunnel-medium would be 802 and Tunnel-Private-Group-ID is the name of the vlan(not the vlan number)
   So for the Cisco ACS 4.x you would create a user as specified above, fill in all the password boxes with MAC address, I believe the mac has to be all lower case in the name and the password. Then check the Separate(Chap/MS-Chap/ARAP) box. Then you pick the group the machine belongs to, the group is the part that defines what vlan it is on.
   Before you create the user, create the group with info I wrote above and in addition specify the Service-Type as Authenticate Only.
    Freeradius is a bit harder to configure the specifics and I am just now testing a freeradius server so I do not know the process for Machine authentication.
    If, however, you are trying to authenticate a user that gets a bit trickier and is not so straight forward.

802.1x authetication with dynamic Vlan assignment by a radius server

Hi
At school I want to start using 802.1x authentication with dynamic Vlan assignment by a Windows Server 2012R2 Radius server.
When a student logs in, I want it to be placed in the "Students" Vlan, when a Administrative employee logs in, I want it to be placed in the "Administative" vlan and when the client is unknown I want to place it in the "Guest" Vlan.
I have several SG200 switches and I configured everything as mentioned in the administrative guide but I cannot get it to work as desired.
What does work:
- If the client is permitted, the switch changes to "authorized" state. (before anyone logs on to the domain with that client)
- When a User logs on that is part of the Administrative employees, the switch changes to "authorized" and when a student logs on, it changes to "unauthorized".
So far so good.
But what doesn't work:
- it does not put the administrative employee in the Vlan "Administrative", it just enables the port on the switch but leaves it in the default vlan 1.
- I can not find the Guest VLAN.
Any help would be appriciated.

Hi Wouter,
Can you see in the packet capture Radius accept message VLAN attribute? Also please ensure you have the latest firmware and boot code:
http://www.cisco.com/c/en/us/support/switches/sg200-26-26-port-gigabit-smart-switch/model.html#~rdtab1
I would recommend you to open ticket with Small Business team so they can go with you through packet capture and configuration steps:
http://www.cisco.com/c/en/us/support/web/tsd-cisco-small-business-support-center-contacts.html
Regards,
Aleksandra

802.1x dynamic VLAN assignment with Radius NPS Server

I can NOT get the NPS and Cisco 3550 switch to drop the authenticated user in a VLAN.
I have followed this documentation,
http://msdn.microsoft.com/en-us/library/dd314181(v=ws.10).aspx
that basically says to use these Radius attributes,
Tunnel-Medium-Type : 802
Tunnel-Pvt-Group-ID : My_VLAN_Number (also tried VLAN name)
Tunnel-Type : VLAN
There is some Cisco documentation that says to use Vendor Specific attributes Cisco-AV-Pair,
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2950/software/release/12-1_19_ea1/configuration/guide/2950scg/swauthen.html#wpxref83693
and I have also tried that,
cisco-avpair= "tunnel-type(#64)=VLAN(13)"
cisco-avpair= "tunnel-medium-type(#65)=802 media(6)"
cisco-avpair= "tunnel-private-group-ID(#81)=vlanid"
My user authenticates on the port fine, but doesn't get put into a VLAN. If I add "sw acc vlan 110" then the user authenticates and then does get an IP address in that VLAN and all is well.
Anybody know how to get dynamic VLAN assignment working with NPS?
NPS on Win 2012 R2
Domain controller separate Win 2012 R2 server
Cisco 3550 switch

Hi All, Can any one guide me to
configure 802.1x with acs 5.0. Its totally new look and m not able to
find document related to 802.1x.Thanks
Hi,
Check out the below link on how to configure 802.1x and ACS administration hope to help !!
http://www.cisco.com/en/US/tech/tk389/tk814/technologies_configuration_example09186a00808abf2d.shtml#MDA
Ganesh.H

802.1x dynamic vlan assignment using ACS 4.2

Hi
we have 10 switches 2960 configured with 802.1x authentication against ACS server 4.2.
we have 2 vlans configured on the switches for administrator and endusers. the end user vlan id is 10 and the administartor vlan is is 100.
we need to apply the following scenario, if the enduser PC - that is connected to vlan 10 - has an issue and the administrator will login to the PC with the administrator account to fix that issue, the switch should dynamically reconfigure the port with the administrator vlan ( 100 ) .
is the above scenario doable using dot1x with the ACS server?
waiting your replies
Mohamed

Hi,
I have the following scenario
2 bulidings with multiple floor
Each floor should be in different VLAN.
The network should be authenticated with 802.1x and each switch port should be assigned with dynamic VLAN from ACS.
Each
user should be able to connect and roam around between any building.
when ever a user is connecting his laptop to any floor, he should be
made part of that respective vlan. It is not requred to have the same
IP rage to be allocated, but the dynamic VLAN should be based on the
switch port location.
Can
I configure ACS in such a way that, the ACS will allocate dynamic VLAN
for every 802.1x authentication based on the Network Device Group.
Please refer the attached diagram
Hi,
Check out the below link for your requirement for dynamic vlan assignement using ACS
http://www.ciscosystems.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml
Hope to Help !!
Ganesh.H
Remember to rate the helpful post

802.1x with VLAN assignment on Catalyst 2950T-48-SI

I will really appreciate if you can confirm me if the C2950T-48-SI will support the following features.
- IEEE 802.1x with VLAN assignment
- SSHv2
- SNMPv3
The data sheet for the Cisco Catalyst 2950 Series Switches with Standard Image mentions all the above and more features for the 2950T-48-SI, but at the same time the power point presentation, (Cisco Catalyst 2950 Series Switches, and the tool Sofware advisor say that those features are only supported with the Enhanced Image.
If your those feature are supported by the Standard Image, would you please also inform the last IOS version supported.
Thanks a lot.

SSH isn't available on the SI version of the 2950 as you require the Crypto features and these are not available for the SI (the documentation is a little vague here but trust me I have upgraded one and it doesn't like it...). The documentation says 'Switches that support only the SI cannot run the cryptographic image.'
802.1x with VLAN assignment is available only in the latest IOS - or at least since 12.1(22).
SNMPv3 is supported.
HTH
Andy

802.1x Dynamic Vlan assignment using ACS

Hi,
I have the following scenario
2 bulidings with multiple floor
Each floor should be in different VLAN.
The network should be authenticated with 802.1x and each switch port should be assigned with dynamic VLAN from ACS.
Each user should be able to connect and roam around between any building. when ever a user is connecting his laptop to any floor, he should be made part of that respective vlan. It is not requred to have the same IP rage to be allocated, but the dynamic VLAN should be based on the switch port location.
Can I configure ACS in such a way that, the ACS will allocate dynamic VLAN for every 802.1x authentication based on the Network Device Group. Please refer the attached diagram

Hi,
I have the following scenario
2 bulidings with multiple floor
Each floor should be in different VLAN.
The network should be authenticated with 802.1x and each switch port should be assigned with dynamic VLAN from ACS.
Each
user should be able to connect and roam around between any building.
when ever a user is connecting his laptop to any floor, he should be
made part of that respective vlan. It is not requred to have the same
IP rage to be allocated, but the dynamic VLAN should be based on the
switch port location.
Can
I configure ACS in such a way that, the ACS will allocate dynamic VLAN
for every 802.1x authentication based on the Network Device Group.
Please refer the attached diagram
Hi,
Check out the below link for your requirement for dynamic vlan assignement using ACS
http://www.ciscosystems.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml
Hope to Help !!
Ganesh.H
Remember to rate the helpful post

WoL over 802.1X with Vlan Assignement

Hello
I have a switch 3560, and an ACS v4
In phase of test i have an infrastructure with 802.1X PEAP with automatic VLAN assignation by the ACS according to the Machine.
My question is:
it possible to implement Wake One Lan on 802.1x with a assigantion of vlan not statics (i.e. without use of command Switchport access vlan XXX)
PS: if I do in statics the VLAN on a port Wake one Lan work without Pb with 802.1X

Ok, on interface 0/19 :
Switchport mode access
speed 100
duplex Full
dot1x pae authenticator
dot1x port-control auto
dot1x control-direction in
spanning-tree portfast
The software use is like "wolcmd" with configuration of
MAC address of the PC
IP of the PC (give by DHCP reservation)
Subnet mask
Remote port Number : 7
The authentication on ACS work fine and on ACS whe have this field
[064] Tunnel-Type
value : VLAN
[065] Tunnel-Medium-Type
Value : 802.
[Tunnel-Private-Group-ID]
Value : 69
In fact, the only difference between config is assignation static or dynamic of VLAN
I don't know if this what you wan't
thanks

802.1x Vlan Assignment

Similar Messages

Maybe you are looking for