ACS 5.1 command authorization in config mode

Hello all,
I have setup an ACS 5.1 system and a Cisco 3560 as test device. On the ACS system I have defined a user that will have limited access to Cisco CLI commands (privilege 15 through Shell Profile and limited commands through Command Sets). While this is working great for commands run under enable mode (meaning that the authorization denied the commands that I've specified in the Command Sets), it seems that it's not working under configure mode (e.g. I have denied commands like "router ospf" , "router bgp" , but the user can still apply them).
Before I've search this forum and found 2 posts:
https://supportforums.cisco.com/thread/2041611
https://supportforums.cisco.com/message/3057298
that suggest to have the AAA configured with:
aaa authorization config-commands
I already have this command and it still doesn't work. Actually my entire AAA config looks like this:
aaa new-model
aaa authentication login default group tacacs+ local
aaa authentication enable default group tacacs+ enable
aaa authorization config-commands
aaa authorization exec default group tacacs+ local
aaa authorization commands 1 default group tacacs+ local
aaa authorization commands 15 default group tacacs+ local
Did I miss something? Do you have any suggestion for me?
Thank you!
Calin

can you run a "debug aaa authorization" to see what happens?

Similar Messages

CSU Rev 2.3.6(2) - deny key commands in IOS config mode

I want to deny certain commands to certain users in a group. I have defined the following on the ACS.
service = shell{
default cmd=permit
default attribute=permit
cmd=configure{
deny="no ip routing"
deny="no router isis"
permit=""
This logic does not work.
1. Does CSU support command authorization within config mode?
2. Any tips?
Thanx,
Kenny

You are not alone with issues related to the e1000e (but all they concluded was that reloading the module makes it work again):
https://bbs.archlinux.org/viewtopic.php?id=145564
It seems like this is more your issue:
http://permalink.gmane.org/gmane.linux. … devel/8932
But if none of those boot flags work for you, then there's not much you can do, and you'll have to write a script to reload the module each time after initial boot finishes I guess until the module gets fixed.
Also, power management of the PCIe interface causes the e1000e to shut off after a while as well (lots of people on CentOS noticing this):
http://serverfault.com/questions/226319 … ie-aspm-do
So you can use that boot parameter to stop that from happening, if that becomes an issue for you as well.

ACS SE - Shell Command Authorization

Hi Sir,
I have deployed an ACS Solution Engine 4.1(1) Build 23 to provide AAA services for routers/switches login.
I'd like to create a user group that is restricted to only "show" commands when the users log in to the network devices.
I have done the following steps:
(1) Shared Profile Components -> Shell Command Authorization Sets
Added a new set. Call it NOC. I added the command "show". For "Unmatched Commands", I selected Deny. I also checked "Permit Unmatched Args".
(2) Group Setup.
Created a new group. Call it NOC. For Enable Options, I selected "Max Privilege for any AAA Client" value of "Level 7".
For TACACS+ Settings, I checked "Shell (exec)" and set "Privilege level" to 7.
For Shell Command Authorization Set, I selected NOC for "Assign a Shell Command Authorization Set for any network device".
(3) User Setup.
Created a new user. Call it noc. Assign it to group NOC. All parameters point to group setting.
(4) The AAA commands on the routers/switches are as follows:
aaa new-model
aaa authentication login default group tacacs+ local enable
aaa authorization exec default group tacacs+ local
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
aaa accounting system default start-stop group tacacs+
ip tacacs source-interface Loopback0
tacacs-server host 10.10.10.10 key 0 tacacskey
When the noc logs in, he's given privilege level 7. True, he's limited to only "show" commands. He can't do "config t". However, he also can't do "show run". Is it normal? I'd need him to be able to do "show run". How to configure the ACS?
Thank you.
B.Rgds,
Lim TS

Hi Narayan,
Appreciate your detailed configuration steps.
My intention is to create a shell command authorization set that allows a user group to only perform "show" commands, including complete config of "sh run". This group is not allowed to configure anything.
See my original post for my configuration steps. I tied the group to the above authorization set and assigned it Level 7.
The outcome is, the user can do all "show" commands except "sh run". Of course, he is not authorized for configuration commands.
I came across the following link:
http://www.cisco.com/en/US/tech/tk59/technologies_tech_note09186a00800949d5.shtml
Perhaps it explains the problem here. If I understand it correctly, a user can't see in the output of "sh run" what he can't configure at his privilege level or below.
The same issue happens when I configured the following:
no aaa new-model
username noc privilege 7 password test
privilege exec level 7 show
line vty 0 4
login local
The user "noc" can't do "sh run".
Thank you.
B.Rgds,
Lim TS

ACS command Authorization on PIX Console

I have configured the pix firewall for ACS authentication and command authorization, everything is working fine
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ (inside) host 172.28.x.x x.x.x
aaa-server TACACS+ (inside) host 172.28.x. xx
aaa authentication ssh console TACACS+ LOCAL
aaa authentication serial console LOCAL
aaa authentication enable console TACACS+ LOCAL
aaa authorization command TACACS+
aaa accounting command privilege 15 TACACS+
aaa accounting enable console TACACS+
but porblem is that i dont wana have ACS authentication while connecting with console. In case of emergency when
ACS down, i wana to get console and access the device by using local username and password
but now after this configuration when i try to access the firewall via console, i m getting error of
command authorization fail.
I dont wana have any command authorization while connected with console, Please tell me how to resolve this issue
I have made the command authorization set in ACS and it is working fine for me,

kindly once again check my modified configuration,
I wanted to use this option in case, ACS goes down and i can console my firewall and but it is not working fine me.
aa-server TACACS+ protocol tacacs+
aaa-server TACACS+ (edn) host 172.28.31.132
aaa-server TACACS+ (edn) host 172.28.31.133
aaa authentication ssh console TACACS+ LOCAL
aaa authentication enable console TACACS+ LOCAL
aaa authentication serial console LOCAL
aaa authentication http console LOCAL
aaa authorization command TACACS+ LOCAL
aaa accounting command privilege 15 TACACS+
aaa accounting enable console TACACS+
but i m not able to login i m getting following eror
Command authorization failed
TDC-INT-525-01> exit
Command authorization failed
TDC-INT-525-01> exit
Command authorization failed
TDC-INT-525-01> enable
Command authorization failed
i also defined the local command authorization set like this
privilege cmd level 15 mode exec command exit
privilege show level 5 mode exec command running-config
privilege show level 15 mode exec command version
privilege show level 0 mode exec command access-list
privilege show level 0 mode configure command access-list
privilege cmd level 15 mode configure command exit
privilege cmd level 15 mode configure command no
privilege cmd level 0 mode configure command access-list
privilege cmd level 15 mode interface command exit
privilege cmd level 15 mode subinterface command exit
privilege cmd level 15 mode dynupd-method command exit
privilege cmd level 15 mode trange command exit
privilege cmd level 15 mode route-map command exit
privilege cmd level 15 mode router command exit
privilege cmd level 15 mode ldap command exit
privilege cmd level 15 mode aaa-server-host command exit
privilege cmd level 15 mode aaa-server-group command exit
privilege cmd level 15 mode context command exit
privilege cmd level 15 mode group-policy command exit
privilege cmd level 15 mode username command exit
privilege cmd level 15 mode tunnel-group-general command exit
privilege cmd level 15 mode tunnel-group-ipsec command exit
privilege cmd level 15 mode tunnel-group-ppp command exit
privilege cmd level 15 mode mpf-class-map command exit
privilege cmd level 15 mode mpf-policy-map command exit
privilege cmd level 15 mode mpf-policy-map-class command exit
privilege cmd level 15 mode mpf-policy-map-class command exit
privilege cmd level 15 mode mpf-policy-map-param command exit
Please tell me how to solve this problem

Aaa accounting for config-mode commands

How to account commands entered in config-mode via TACACS+ ?
aaa accounting commands 15 default start-stop group tacacs+
does accounting for all commands in privilege level 15.
Best Regards
Carsten

Carsten
I am not clear what your question is. From the title I gather that you are looking for a way to have accounting records for commands entered in config mode. The answer to the question is to enable accounting for level 15 commands which include the config commands. All of which is included in your message. So what is the question?
If the question is how to get just the config commands without all the other level 15 commands I am not aware of any way to get just the config commands.
HTH
Rick

ACS 3.3 Config Command Authorization

Hi,
I want to allow an user only to add/remove routes on a router. The shell command authorization works fine. But when the user is in config mode, he can start any command!
The debug says:
1w2d: AAA/AUTHOR: config command authorization not enabled
How can I enable this and how/where can I configure it on the ACS?
Thanks in advance

On ACs just allow the user to enter the "route" command like you have any other shell command they're allowed to do.
On the router/NAS, you have to tell it specifically that you want authorization for config commands with the following:
aaa authorization config-commands
Note that the format of this command changes slightly on different IOS versions, but if you do "aaa authorization ?" you'll be able to figure it out.

ACS command authorization report in conf t mode

Hi, this is probably a quick one, but I couldnt find a solution so far.
We are using command authorization via ACS and are thus able to see (in case of any issues) who has entered which commands at which time on which device. But this only works until someone enters conf t mode. After that I am not getting log entries in the ACS (Version 5). I can see all show commands and who entered the configuration mode, but nothing after that. Config snippet:
aaa new-model
aaa authentication attempts login 5
aaa authentication login default group tacacs+ local line enable
aaa authentication enable default group tacacs+ enable
aaa authorization exec default group tacacs+ local
aaa authorization commands 1 default group tacacs+ local
aaa authorization commands 15 default group tacacs+ local
aaa accounting exec default start-stop group tacacs+
aaa accounting commands 1 default start-stop group tacacs+
aaa accounting commands 15 default start-stop group tacacs+
aaa session-id common
My guess is that I allow all commands with that and thus no authorization is needed.
Any idea?
Thanks
Chris

Command Authorization Config best practice using ACS

Hi
Is there any best practices for configuring Command authorization (for router/switch/asa) in CS-ACS? To be specific, is there any best practices to configure authorization for a set of commands allowed for L1,L2,L3 support levels?
Regards
V Vinodh.

Vinodh,
The main thing here is to ensure that we have backup/fall-back method configured for command authorization, inorder to avoid lockout situation or do wr mem once you are sure configs are working fine.
Please check this link,
http://www.cisco.com/en/US/products/sw/secursw/ps2086/products_configuration_example09186a00808d9138.shtml
Regards,
~JG
Do rate helpful posts

ACS Shell Command Authorizations Set

I have Cisco ACS Server V4.0
In the shell Command Authorization Set I configure a restrict Access.
In the privilege mode the restriction of the commands works good, but when I enter in the config prompt the restriction don't works. In this promt I can enter all commands.
Why This?

I have the same error with ACS Server 4.2. I can restrict in privilege mode but global config is wide open. Also any command i block in privilege mode can still be executed in global config using the "do" command. How do i block that, or find out what commands the router is sending to the ACS.

Cisco Secure ACS 4.2 - Group Setup w/Shell Command Authorization Sets

Hello All,
I am trying to create a user so that I can provide him only to run commands that I have designated them to run within my "Shell Command Authorization Set". This seems to work great, however I cannot find anywhere I can "hide" commands they do not have access to. For instance, once the user is logged into the switch they can do a show ? and get a list of commands. I would like to know if there is an option to only display commands the user has access to in ACS.
My Steps:
Created a user in ACS
Shared Profile Components
Create Shell command Autorization Set - "ReadOnly"
Unmatched Commands - Deny
Unchecked - Permit Unmatched Arg
Commands Added
permit interface
permit vlan
permit snmp contact
permit power inline
permit version
permit switch
permit controllers utilization
permit env all
permit snmp location
permit ip http server status
permit logging
Created a group - "GroupTest" with the following
Confirgured - Network Access Restrictions (NAR)
Max Sessions - Unlimited
Enable Options - No Enable Privilege
TACACS+ Settings
Shell (exec)
Priviledge level is check with 1 as the assigned level
Shell Command Authorization Set
"ReadOnly" - Assign a Shell Command Authorization Set for any network device
I have configured following on my Router/Switch
aaa authorization config-commands
aaa authorization commands 1 default group tacacs+ if-authenticated
privilege exec level 1 show log
I have attached below the documention I have gone over.
http://www.cisco.com/en/US/products/sw/secursw/ps2086/products_configuration_example09186a00808d9138.shtml
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_server_for_windows/4.2/user/guide/GrpMgt.html#wp478624

"you are testing with privilege level 15 or below 15. Because when you are using below 15 level user, first it will check local command authorization set. For example if you want to execute sh runn command with level 5 user, first it will check local command set. If the sh runn command exits in local command set then it will send request to ACS. If it is not in the command set, it won't send request to ACS. That's why you don't see debug. For 15 level users it will directly send request to ACS. Configure command set locally and try it should work.
Correct me if I am wrong."
Regards
Vamsi

ACS - Shell Command Authorization Sets

Hi,
I have had a problem where a set of users in two groups in ACS are struggling entering commands. The commands are set in the Shell Command Authorization Sets and this hasnt changed. Other commands are working. As this is spanning two groups in ACS I am thinking it's not something with the groups but the command sets itself.
Just to check, the commands are 'clear port-security' and clear mac address-table' - I have entered in Command 'clear' and the following attributes;
permit port-security
permit mac address-table'
I've also ticked 'Permit unmatched args'
At the same time as this is occuring I have been recieving the following messages from the ACS server via email;
Test Timed out for service: CSAdmin
Test Timed out for service: CSAuth
Test Timed out for service: CSDbSync
Test Timed out for service: CSLog
I have looked at other posts and have restarted CSMon. This then stops the messages for some time, then a day or so later I get the messages again.
Could this be tied in with the command issue? Is there something else I should look at other than restarting the server and the CSMon service again? All other CS' services are running.
Thanks!!
Steve

Thanks for your reply!
there are no errors, the switch ios is putting the asterics as it does when you enter a command that is not recognised, i.e. for clear port-security the port-security onwards is not recognised. On this note, the user is entered into priviledge mode and not in configure terminal mode, just base priviledge mode. The group in ACS is set to max priviledge level 7 and have also set this on the user account in addition.
I am using ACS v 4.1.
While I receive the service messages and also when they go away - I always have the authorisation problem.
Thanks
Steve

Command Authorization in ACS

Hi,
Can anybody tell me how can I permit only ping command to a group in ACS. What is the actual statement that I want to add in command authorization sets.

Hi Prem,
Can you let me know how can i restrict a group from adding a route. I have the following configured on the ACS under shell authorization
configure ......permit terminal
interface ......permit fastethernet (permit Unmatched arg)
show............permit vlan
switchport......permit access &
permit vlan
With the above configuration iam still able to add a route to the config
Also i would like to know the wildcard to be used for enabling all the fastethernet or Ge ports
thanks in advance
Narayan

Cisco ACS command authorization sets

I need help on the following please.
1. - I am using ACS as TACACS server to control IOS authorization on all our Switches, However I can not deny telnet sessions to other devices from within CatOS - does anyone know the command authorization set to deny this within ACS ????
2. Does anyone know where I can read up on command authorizations sets for ACS ??
3. What is the debug command for CatOS to see cli output ?
Many thanks
Rod

Thanks for your info. I have solved my problem -
1. I enabled tacacs administration logging using command on switch aaa authorization commands 15 default group tacacs+
This let me see what what happening everytime I entered a command on CatOS - via the logging monitor on ACS. From here i was able to see that when i was trying to telnet to a device from CatOS it was doing it on Privilage mode 1. I then entered this command aaa authorization commands 1 default group tacacs+ which solved my telnet problem.
Problem resolved.
Many thanks.

Shell Command Authorization Sets ACS

hi i followed this guide step by step http://www.cisco.com/en/US/products/sw/secursw/ps2086/products_configuration_example09186a00808d9138.shtml
but still all my user can use all the commands
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname R3
boot-start-marker
boot-end-marker
aaa new-model
aaa authentication login milista group tacacs+ local
aaa authorization config-commands
aaa authorization exec default group tacacs+ local
aaa authorization commands 0 default group tacacs+ local
aaa authorization commands 1 default group tacacs+ local
aaa authorization commands 15 default group tacacs+ local
aaa session-id common
memory-size iomem 5
ip cef
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
multilink bundle-name authenticated
username admin privilege 15 secret 5 $1$CS17$3oeNpzTvJAyZTvOUP2qyB1
archive
log config
hidekeys
interface FastEthernet0/0
ip address 192.168.20.1 255.255.255.0
duplex auto
speed auto
interface Serial0/0
no ip address
shutdown
clock rate 2000000
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface Serial0/1
ip address 20.20.20.2 255.255.255.252
clock rate 2000000
interface Serial0/2
no ip address
shutdown
clock rate 2000000
interface Serial0/3
no ip address
shutdown
clock rate 2000000
router eigrp 1
network 20.0.0.0
network 192.168.20.0
no auto-summary
ip forward-protocol nd
no ip http server
no ip http secure-server
tacacs-server host 192.168.20.2 key cisco
control-plane
line con 0
exec-timeout 0 0
logging synchronous
login authentication milista
line aux 0
line vty 0 4
end
i copy the authorization commands from the cisco forum and follow the steps but no thing all my users have full access to all commands
heres my share profile
name-------------admin jr
Description---------for jr admin
unmatched commands------- ()permit (x)deny
permint unmatched args()
enable
show -------------------------- permit version<cr>
permit runnig-config<cr>
then i add this profifle to group 2 and then i add my user to the group 2
then i log in to the router enter with the user and i still can use ALL the commands i dont know what i am doign bad any idea?
can you give me if you can a guide to setup authorization with ACS i cant find any good guide jeremy from CBT gives a example but just for authentication i am lost i am battling with this prblem since wednesday without luck

"you are testing with privilege level 15 or below 15. Because when you are using below 15 level user, first it will check local command authorization set. For example if you want to execute sh runn command with level 5 user, first it will check local command set. If the sh runn command exits in local command set then it will send request to ACS. If it is not in the command set, it won't send request to ACS. That's why you don't see debug. For 15 level users it will directly send request to ACS. Configure command set locally and try it should work.
Correct me if I am wrong."
Regards
Vamsi

ACS Shell Command Authorization Set + restricted Access

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin-top:0in;
mso-para-margin-right:0in;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0in;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
Hi ,
I have tried to Create a restricted Access Shell Command Authorization Set on ACS as told on the Cisco Url
http://www.cisco.com/en/US/products/sw/secursw/ps2086/products_configuration_example09186a00808d9138.shtml
After I applied the same on a User Group I found the users on the group have complete access after typing the conf t on the equipments . My ultimate aim was restrict the access only at Interface level , Attached is the config details . Could anyone has come across such scenario . Please check my config and let me know any thing need to be done specially from My Side
Thanks in Advance
Regards
Vineeth

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin-top:0in;
mso-para-margin-right:0in;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0in;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
Hi Jatin ,
first of all Thank you very much . It startted working after aaa authorization config-commands
here I was trying to achive one specfic thing .
I want to stop the following commands on ACS “switchport trunk allowed vlan 103” . I only want allow “add” after “vlan” and block rest all arguments
But even after setting the filter on ACS Still we are able to execute the command is there anything like we cannot control the commands after the sub commands
Also I am attaching the filter list along with this. Could you have look on this and let me know whether I have configured something wrongly. Other than this is there any work around is available to achieve this .
Thanks and Regards
Vineeth

ACS 5.1 command authorization in config mode

Similar Messages

Maybe you are looking for