Airport Extreme Simultaneous Dual-Band port forwarding broken if only TCP ports with firmware 7.6.1

When configuring my Airport Extreme Simultaneous Dual-Band router, port forwarding is broken if you only specify TCP ports to forward. This is with firmware 7.6.1. What happens is that after you hit the Update button, when the router comes back and you open the port forwarding entry, the IP is still there but the port numbers are missing.
I tried all different port numbers and ranges and nothing would stick if i only specified TCP ports. If i added UDP ports with the TCP ports then it would save them. And if you add a new entry with only UDP it saves them too.
Now this is with adding a new port forwarding. I already have existing ports being forwarded that only have TCP. They are still working. I believe i added them with a previous version of the firmware.
Any one else see this issue? Any ideas?
Maybe i should perform a hard reset and reload a saved config.
Peace,
Dan

I haven't seen the issue but you could just downgrade to an earlier firmware:

Similar Messages

  • Simultaneous dual band router for FiOS

    I've just got a FiOS Triple play with a modem/router, M1424WR.
    I ordered for 50/25 Mbps, but I'm getting 60/40 wired.
    The router is downstairs right next to where the cable came inside,
    and I'm getting mostly 25/20 wireless downstairs.
    However, whenever the microwave oven in the kitchen runs,
    the wireless connection doesn't work. So I'm thinking of buying a simultaneous dual band router.
    How would I configure it with the Verizon modem that originally came with?
    Any help would be appreciated.

    Can I use my wireless or an extra router along with the Verizon provided router?

  • Extending a simultaneous dual-band network using an Airport Extreme

    I have a new Time Capsule that can operate in simultaneous dual-band mode. I have a single SSID for both the 2.4 GHz and 5 GHz networks, and all of my devices correctly connect using the appropriate frequency.
    I also have an older square Airport Extreme that's dual-band capable (but not simultaneous dual-band). I have this Airport Extreme set up to extend the network from the Time Capsule, but it's extending the 5 GHz network rather than the 2.4 GHz network. I'd rather have it extend the 2.4 GHz network because our iPhones move around the house much more often than our other wireless clients.
    I know that I could go back to having different SSIDs for the 2.4 GHz and 5 GHz networks, and then telling the Airport Extreme explicitly to extend the 2.4 GHz network, but I'm really enjoying having a single SSID that any device can use to connect to my network.
    Thanks,
    Scott Gardner

    Thanks for the replies. Right now, there's about 30 feet, two interior plaster/lathe walls and a closet between the Time Capsule and the Airport Extreme. The area of the house where I'm trying to improve the 2.4 GHz reception (an attached studio) is only about another 18 feet, one interior wall and one exterior wall further past the Airport Extreme's current location. I can't put the Airport Extreme any further from the Time Capsule because the 18 feet between its current location and the attached studio is an open area.
    If there are no hidden settings that I'm missing, I guess I'll just break the network back into two discrete SSIDs and explicitly tell the Airport Extreme to extend the 2.4 GHz network.
    Thanks again,
    Scott Gardner

  • I have both a simultaneous dual band and a regular dual band airport extreme on an extended network will the 5ghz work at its full potential if its the one that is extending the network?

    I have a A1143 model Airport extreme with dual band capabilities but not simultaneous, i'd like that to run on the 2.4ghz band, while i have a A1408 model airport extreme as the "extender" but i want to make sure that even though im running the 2.4 and the newer model is extendeding it, my simulataneous dual band will still work to its full potential (ie: 300mbs i think is the max for the 5ghz)..?
    notes: no i can't use the newer model as the primary and the older model as the extender.

    I am assuming that your simultaneously dual-band Extreme is using the same Network Name for both radios. If that is the case, and depending on the distance between AirPorts, the extending Extreme is most likely just extending the 2.4 GHz radio. That would leave the 5 GHz wireless network basically "untouched."

  • Apple TV vs Apple AirPort Extreme Base Station (Simultaneous Dual-Band)

    I have an original 40 GB TV that connects to my new ( (latest model)) Apple AirPort Extreme Base Station (Simultaneous Dual-Band) (MC340LL/A). Since upgrading to this new AEBS, my TV will not connect via its internal Airport card. The TV will "see" my "Home-LAN" but always gives the error message, "Connection Failed".
    I have tried to Reset and Restore the TV, even the "Restore to Factory Defaults"! I have changed the security settings on my AEBS from an Open Network (no security) to WPA/WPA Personal, WPA Personal. I have changed the "Radio Mode" from "802.11a/n - 802.11b/g" to "802.11a - 802.11b/g". The TV will not connect! I now have it connected to my "Home_LAN" via Ethernet, and it works fine.
    Anyone with a similar problem and a suggestion or solution? Do you think the internal Airport Card is the problem? Thanks

    As suggested in another discussion area, (AirPort), I reset the AEBS to factory defaults. On the TV, I went to >Settings>General>Network>Configure Wireless>Wireless Networks. I could then see the generic "Apple Network xxxxx" on the TV. From my MacBookPro, I verified that I could connect to the TV by launching iTunes and noting that the TV was now visible in the "Devices" menu. Went back to the AEBS and ran through the "Setup" routine. I did NOT use the "Previous Settings" but instead, saved the old settings profile, created a new wireless network and new settings profile and enabled WPA2 Personal encryption. I then went back to the TV and went through the "Settings" routine again (as noted above). This time, after entering my WPA2 password, the TV connected to the network and problem was solved. Thanks.

  • Airport Express supports dual-band. Airport Extreme supports simultaneous dual-band. What's the difference?

    What is the difference between the two. And which one would be better for extending my wifi signal for my ipod touch
    http://www.apple.com/wifi/

    Hi Joel,
    Simultaneous dual band = can process signals on both bands concurrently.
    dual band = can process a signal on one band at a given time,  either or.

  • Simultaneous Dual Band for Last Gen. Airport?

    Does anyone know if the latest software update ADDS dual band support to the previous generation of Airport Extremes? I bought the previous generation base station about 3 months ago. It would be cool if I got the enhanced functionality with a software update.
    Thanks

    All of the AirPort 802.11n products are dual-band. They can operate in either 2.4GHz or 5GHz, but not at the same time--they need to be reconfigured in AirPort Utility to switch.
    The new AirPort Extreme and Time Capsule just introduced each have two 802.11n radios, one in 2.4GHz and one in 5GHz, so they can operate in both bands at the same time. It's called "simultaneous dual band" or "concurrent dual band" by others. But it does mean a hardware change, so it won't be available as a firmware upgrade to older AirPort APs.

  • Can you add new AirPort Express Base Station Simultaneous dual-band 802.11n with a 1st Gen time capsule network

    Hi
    Has anyone tried using the AirPort Express Base Station with a first generation Time Capsule and used it to extend their network, while still being able to use the Simultaneous dual-band 802.11n on their network?
    Thanks in advance

    The first generation Time Capsule was not a simultaneous dual band device.
    If you add the "new" AirPort Express to the network and configure it to "Extend a wireless network", it will extend the one single band signal that it is receiving from the Time Capsule.
    In other words, the AirPort Express will not extend simultaneous dual bands in this type of setup...since it can only "extend" what it receives. You would need a simultaneous dual band Time Capsule if you want that type of functionality.

  • Alternative simultaneous dual band router that supports NTFS?

    I was totally smitten with my Airport Extreme, until I had to change all of my media hard drives to NTFS (they had hit the characters per directory limit that FAT32 has).
    I need to keep them as NTFS, because my TV only reads FAT32 or NTFS hard drives (i.e. I couldn't change to HFS+)
    So my question is, does anyone know of a simultaneous dual band router (5ghz + 2.4ghz) which has gigabit ethernet ports and a USB port which supports NTFS hard drives?
    From researching, the big competitors are the Linksys WRT610N and the Netgear DIR-855. Problem is, the Linksys and Netgear support forums are filled with posts from people claiming NTFS hard drives either don't work at all, or are severely temperamental
    I could go for a NAS, but I just managed to get a pair of 2TB Western Digital USB hard drives for £98 each. I've been unable to find a 2TB (single hard drive) NAS for less than £170.

    Can I use my wireless or an extra router along with the Verizon provided router?

  • Where can I download 7.4.2 firmware for my Simultaneous Dual Band II AE

    After upgraded to the latest firmware, the time machine disconnect randomly, so does my NAS' file shareing.
    As other topic says, I want to downgrade my AE to 7.4.2. I remember days before upgrading firmware, everything's well.
    I can't find any download for my Simultaneous Dual Band II AE, only Simultaneous Dual Band (no II). Can someone tell me where I can download it?
    Thanks.

    Michael,
    This may or may not help.... But it just might get someone to either tell us I'm right or point us in a better direction....
    I have one AE and three AX's. All recent "n" models. My AE was using v7.5.1 and the three AX's were on v7.4.2. My version of AirPort Utility is v5.5.2. All was well WiFi land....
    I recently updated all of them to firmware v7.5.2. They are working OK, but I have lost some of my RSSI. It is about three clicks worst than it was. It went from a constant -58 ~ -59 to -62 ~ -64. (My iMac is not in the same room as my AE.)
    If I weren't so "anal" I'd just live with it..... But I'm thinking of reverting them back.
    AE from v7.5.2 TO v7.5.1
    AX's from v7.5.2 TO v7.4.2
    I have found v7.5.1 and v7.4.2 in the following folders:
    (users)you>Library>ApplicationSupport>Apple>AirPort>Firmware>107>v7.4.2 & v7.5.2 / 114>v7.5.1 &7.5.2
    Once located I think that we go to AirPort Utility, Select the AE or an AX, click Manual set up, Click "Version" on the first screen, then at the drop down select "Other". Next using the now opened Finder, go to one of the above folders and select the version to revert to and update.
    I think this just might work..... *Again maybe someone can advise on this.......*
    Oh, it's a good idea to locate the AE and AX's close to your computer. I just plug one at a time into an outlet next to my computer.
    Hope we hear from an "expert" on this.....

  • Where can I purchase AC Adaptor for my Airport Extreme as the original one is broken?

    Where can I purchase AC Adaptor for my Airport Extreme as the original one is broken? I have tried to go to Apple Store in Singapore / Hongkong, they do not sell just the AC adaptor. They asked me to purchase new Airport Extreme / upgrade to Time Capsule.

    Here's one source for these adapters:
    We Love Macs

  • Simultaneous Dual Band AP?

    I'm not terribly familiar with cisco's WAPs outside the small business models and I'm trying to find an "inexpensive" autonomous AP that supports 802.11n, simultaneous dual band, and internal antenna.  Are there any comparison charts showing which access points support simultaneous dual band?
    Thanks!

    I see where it says that it 2.4 and 5.0 radios, but not that they can both be in use at the same time.  Are all of the non-small business APs with dual radios capable of working on both frequencies at the same time?
    Said who???  Single- or Dual-band radios work simultaneously.  It doesn't make any logical sense if they don't.

  • Simultaneous Dual Band Devices and Netctl

    I've got a simultaneous dual-band capable router as well as several simultaneous dual-band NICs. How does one setup a netctl profile to choose to use the "BGN"/2.4GHz band, the "AN"/5GHz band or both concurrently?

    I've got a simultaneous dual-band capable router as well as several simultaneous dual-band NICs. How does one setup a netctl profile to choose to use the "BGN"/2.4GHz band, the "AN"/5GHz band or both concurrently?

  • Simultaneous Dual-Band & Dual-Band II

    What is the difference between these two types of simultaneous dual-band ? Can you upgrade from one to the other via a firmware upgrade ?
    Thanks

    Can you provide the make and model numbers of the devices that you are asking about?

  • What's the difference between Dual Band and Simultaneous Dual Band?

    I just wondered what the difference between Dual Band and Simultaneous Dual Band was?

    Nevermind, I know now!

Maybe you are looking for

  • Adding new field KUONR in VF05 Standard Report from table VBRK

    Hello All, I need to add the Assignment Number Field KUONR from the table VBRK into VF05 standard Report and show the respective Assignment Number for the Billing Document. Please suggest the exact OSS note and the process The SAP Version is SAP ECC

  • QR code model type supported by Adobe live cycle

    Hi All, Which model type of QR code supported by Adobe?? model 1 -- normal prototype model 2 --  enhanced Is there any one who can tell me the difference between 2 model type of QR code?? Regards Abhishek Email Id -: [email protected]

  • Javax.management.AttributeNotFoundException: Attribute is readonly.

    Hello,           I've received such an Exception:           javax.management.AttributeNotFoundException: Attribute is readonly. : com.bea:Name=CTCFuzzyMultiDataSource,Location=ctcdomain,Type=weblogic.j2ee.descriptor.wl.JDBCDataSourceParamsBean,Parent

  • Adobe Flash CS4 - Install of a cd/dvd

    Downloaded and extracted the files from Adobe.  If i run the installation to the extracted location on the hard drive it works fine and the serial number authenticates.  When I burn the files to cd and run the setup.exe off the cd it starts up fine a

  • Mass PO print

    Dear All, My user wants to take printout of PO more than one copy each time. He does not want to go to ME23N or spool request to take the repeat printout. How can we take the printout of PO for more than one copy at a time. Is there any T-code for th