Asa-5512-x no connectivity to internet
I am going from a pix-515e to asa-5512-x. I used the wizard for the initial setup. I then set the interfaces the same, objects, nat rules, routes, ACLs the same as in the 515e (except for the outside interface ACL where you use the inside address now, rather than the outside...and you have a global deny rule for all interfaces) .
I take the cables from the inside / outside interface from the 515e, plug them into the 5512x and nada...
Computers on the inside can't get out. I see egress failures on the ASDM monitor from the inside to outside. I don't see any traffic coming in on the outside interface to the inside as I do on the ASDM of the 515e.
ASA Version 9.1(5)
hostname ASA-5512-X
domain-name mydomain.com
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address 98.xxx.xxx.xxx 255.255.255.224
interface GigabitEthernet0/2
nameif inside
security-level 100
ip address 10.0.1.242 255.255.252.0
interface Management0/0
management-only
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
boot system disk0:/asa915-smp-k8.bin
ftp mode passive
clock timezone CST -6
clock summer-time CDT recurring
dns domain-lookup inside
dns server-group DefaultDNS
name-server 10.0.3.42
domain-name mydomain.com
same-security-traffic permit intra-interface
access-list inside_access_in extended permit ip any any
access-list outside_access_in extended permit tcp any object webserver-inside object-group web-ports
pager lines 24
logging enable
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu management 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-716.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source static webserver-inside webserver-outside unidirectional
nat (inside,outside) after-auto source dynamic any interface
access-group outside_access_in in interface outside
access-group inside_access_in in interface inside
route outside 0.0.0.0 0.0.0.0 98.xxx.xxx.xxx 2
route inside 172.20.0.0 255.255.0.0 10.0.0.1 1
route inside 172.21.0.0 255.255.0.0 10.0.0.1 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 10.0.0.0 255.255.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
telnet 10.0.0.0 255.255.0.0 inside
telnet 192.168.1.0 255.255.255.0 management
telnet timeout 5
console timeout 0
management-access inside
dhcpd address 192.168.1.2-192.168.1.254 management
dhcpd enable management
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home reporting anonymous
At a quick glance the config looks pretty clean (please do use ssh and not telnet though)
Since you replaced one box with another, have you checked that your upstream (Outside) device is reachable from the ASA itself? (i.e can you ping your default gateway at 98.xxx.xxx.xxx 2 )
I've sometimes seen cases where we had to ask the ISP to clear their ARP cache when changing out firewalls.
Similar Messages
-
I've pasted my config below,but cannot get the ASA onto the internet.
*** NEW *** 7pm EST 6.6
Ok; I've been following your setup, but something is still amiss.... i.e. please see the running config below.. Please note that I have the 'modem/T1' into the firewall and then the firewall into an unmanaged switch to LAN PCs. When I have now the firewall connected; it sees the network name/information but cannot get outside. When I ping management to inside (good) / inside to management (good) / either management or inside to outside (not good; says inside interface is shut down???)
Getting there though!! THANKS for the assistance.
Result of the command: "Show running-config"
: Saved
ASA Version 9.1(2)
hostname IOSASA
enable password LCF3phzihasrhsIb encrypted
names
interface GigabitEthernet0/0
nameif Outside
security-level 0
ip address 69.61.160.154 255.255.255.248
interface GigabitEthernet0/1
nameif Inside
security-level 100
ip address 191.0.0.1 255.255.255.0
interface GigabitEthernet0/2
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
shutdown
no nameif
no security-level
no ip address
interface Management0/0
management-only
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
ftp mode passive
same-security-traffic permit inter-interface
object network Inside_net
subnet 191.0.0.0 255.255.255.0
access-list Inside_access_in extended permit ip 191.0.0.0 255.255.255.0 interface Outside
pager lines 24
logging enable
logging asdm informational
mtu management 1500
mtu Inside 1500
mtu Outside 1500
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (Inside,Outside) source dynamic any interface
access-group Inside_access_in in interface Inside
route Outside 0.0.0.0 0.0.0.0 69.61.160.153 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
http 191.0.0.0 255.255.255.0 Inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpool policy
telnet timeout 5
ssh timeout 5
ssh key-exchange group dh-group1-sha1
console timeout 0
dhcpd address 191.0.0.2-191.0.0.254 Inside
dhcpd enable Inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:18525d032551ef1212d442e13e32fe43
: endI assume that the update/addition to the original post was in response to the suggestions from Marvin. I see that you did get the object defined for inside_net but I do not find this line in the config
nat (inside,outside) dynamic interface
and that is the critical part of the change.
HTH
Rick -
How to Configure Cisco ASA 5512 for multiple public IP interfaces
Hi
I have a new ASA 5512 that I would like to configure for multiple public IP support. My problem may be basic but I am an occasional router admin and don't touch this stuff enough to retain everything I have learned.
Here is my concept. We have a very basic network setup using three different ISPs that are currently running with cheap routers for internet access. We use these networks to open up access for Sales to demo different products that use a lot of bandwidth (why we have three)
I wanted to use the 5512 to consolidate the ISPs so we are using one router to manage the connections. I have installed an add on license that allows multiple outside interfaces along with a number of other features.
Outside Networks (I've changed the IPs for security purposes)
Outside1 E 0/0 : 74.55.55.210 255.255.255.240 gateway 74.55.55.222
Outside2 E 0/2: 50.241.134.220 255.255.248 gateway 50.241.134.222
Inside1 : E 0/1 192.168.255.1 255.255.248.0
Inside2 : E 0/3 172.16.255.1 255.255.248.0
My goal is to have Inside 1 route all internet traffic using Outside1 and Inside 2 to use Outside2. The problem is I can't seem to do this. I can get inside 1 to use outside 1 but Inside2 uses Outside 1 as well.
I tried adding static routes on Outside2 to have all 172.16.248.0/21 traffic use gateway 50.241.134.222 but that doesn't seem to work.
I can post my config up as needed. I am not well versed in Cisco CLI, I've been using the ASDM 7.1 app. My ASA 5512 is at 9.1.
Thanks in advance for the suggestions/helpI have been away for a while and am just getting caught up on some posts. so my apology for a delayed response.
I find the response very puzzling. It begins by proclaiming that to achieve the objective we must use Policy Based Routing. But then in the suggested configuration there is no PBR. What it gives us is two OSPF processes using one process for each of the public address ranges and with some strange distribute list which uses a route map. I am not clear what exactly it is that this should accomplish and do not see how it contributes to having one group of users use one specific ISP and the other group of users use the other ISP>
To the original poster
It seems to me that you have chosen the wrong device to implement the edge function of your network. The ASA is a good firewall and it does some routing things. But fundamentally it is not a router. And to achieve what you want were a group of users will use a specified ISP and the other group of users will use the other ISP you really need a router. You want to control outbound traffic based on the source of the traffic, and that is a classic situation where PBR is the ideal solution. But the ASA does not do PBR.
HTH
Rick -
i have an Cisco ASA 5512 working as Firewall
We configure one ASA interface connecting to Cisco router 1700 with leasd line internet service without any problem.
Now we have an extra internet connection ADSL 2MB connected to another ASA interface
I configure the ASA like this :
1- Enable interface 2 on ASA and connect it to ADSL router (interface ip 192.168.1.100 from the same ADSL router {192.168.1.1}range )
2- Create Access rule say source (My computer ip) destination ADSL network range action accept
3- Create Nat Rule say source interface inside source ip (my ip) destination interface ADSL ip 192.168.1.100 destination source router ip 192.168.1.1
4- Add static route say ADSL interface source ip my ip gateway ADSL router
This steps what I do but it doesn't work.
Thanks in advanceFYI for internet access I doubt this will work because if you configure two default route then ASA won't distribute traffic across two interface, first default route will be the one where ASA will send traffic. However from your description it is not very clear which IP address you are trying to ping and how exactly rules you have configured.
Either attach your config or paste the relevant config in post. -
Remote access VPN clients connected to Internet from VPN
Greetings,
I need to let remote VPN clients to connect to Internet from the same ASA VPN server
" client connects to ASA through VPN tunnel from outside interface then access Internet from the same ASA from outside interface again
thanksyou'll need to configure 'same-security-traffic permit intra-interface' on the ASA .
Also, need to setup the corresponding nat statements for your clients pool range.
i.e.
global (outside) 1 interface
nat (outside) 1 access-list anyconnectacl
where anyconnectacl is the pool for your clients:
access-list anyconnectacl permit ip 172.16.1.0 255.255.255.0 any -
ASA 5512-X - VPN & local clients DHCP relaying (DHCP Proxy vs. DHCP Relay conflict)
Hey all,
I have ASA-5512-X serving as general firewall/router. It also serves as AnyConnect SSL VPN gateway (webvpn).
It has ~10 VLANs connected over 1 trunk port. One of the VLANs has DHCP server that shall serve all the VLANs (192.168.16.2).
I'm trying to have the ASA relay DHCP requests from all VLANs to the DHCP server and to also serve VPN clients.
However, according to bug https://tools.cisco.com/bugsearch/bug/CSCsd22469 both DHCP Proxy (webvpn) and DHCP Relay (local interfaces) can't be enabled at the same time.
As VPN clients connect to the same VLANs as local users (eg. VLAN 2 - 192.168.2.0/24) I want to have the very same DHCP server serving both, otherwise it's gonna become a mess.
Note: if I configure DHCP Relay functionality and disable DHCP Proxy - local clients are served fine. If I configure DHCP Proxy (webvpn) and disable DHCP Relay VPN clients are served fine. I therefore consider setup to be correct, just the ASA limitation won't allow me to make it serve both.
Can DHCP Relay also serve VPN clients (no DHCP Proxy enabled)? did I miss something?
Thanks!Hi,
The only workaround for this issue is to configure the ASA itself to act as DHCP server for vpn clients. You also have the flexibility of using local pool and AAA server. Why exactly do you want to use the same DHCP server for both?
AM -
I installed a new ASA 5512-X over the weekend for a client. Their backup ISP connection is DHCP based. I need to use the 'dhcp client route track' command on the interface, but it is not available. However according the all the documentation I am looking at and even the ASDM says it should be available.
This is the version of ASA and ASDM they are running:
Cisco Adaptive Security Appliance Software Version 8.6(1)1
Device Manager Version 6.6(1)
I did upgrade to the latest ASA software, so has this command been removed? If I do a '?' in the interface, there isn't a 'dchp' option.
Any help would be appreciated. I really don't want to tell them they need to get a static IP address to resolve this issue.
TIA,
DanLooks like you are hitting bugID: CSCtq78280
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtq78280
Pls open a TAC case to get the fixed on version 8.6.1(x). -
Connect to internet button inactive (greyed out)?
To bluetooth connection to my E52-1 RM-469 (Firmware 034.001) works. I can view messages, synchronize and so on. Also internet connection over USB-cable works.
When connected by bluetooth the button under tools "connect to internet" is inactive (greyed out). I haven't found any entry in the knowledge database about this behaviour.
While initially creating the bluetooth connection it said something like "bluetooth driver installation postponed".
Nokia Ovi Suite 2.2.0.245
Nokia PC Suite 7.1.40.1
PC Connectivity Solution 10.26.0.0
Connectivity Cable Driver 7.1.31.0
Nokia Ovi Suite Software Updater 2010.18.0.60492
Maps Service API 4.0.11.0
Nokia mPlatform 2.6.195
Ovi Desktop Sync Engine 1.3.0.32
Operating system:
Microsoft Windows XP 32-bit Edition, Service Pack 3
Language: Deutsch
Detected internet browsers:
- Microsoft Internet Explorer 8.0.6001.18702
- Mozilla Firefox 3.6.3 (Default browser)
Detected Bluetooth stacks:
- Microsoft (Version: 5.1.2600, Build: 5512), In use.
- IVT BlueSoleil (Version: 2.7.0, Build: 46), In use.
Detected USB drivers:
- Default Hub Driver for USB 5.1.2600.5512
- USB Modem Driver 5.1.2600.5512
- EHCI eUSB Miniport Driver 5.1.2600.5512
Why is it greyed out (inactive)? How can I connect to the internet using my phone and bluetooth?Hi prospoko!
Did you installed latest drivers for Bluetooth stack?
Also Under Bluetooth settings, look for "services" and make sure "Dial-up" is checked.
i don't know about XP but in Win7 it is found under Control Panel> devices and printers>"Nokia Bluetooth phone" >properties>"Services" tab>dial-up.
Right click on "My Computer">manage>device manager>modems>look if "Nokia E52 Bluetooth Modem" is installed.
Previous Phones: 6600, 7610, 6230, 6230i, 1100, 1112, N70, N73, N95, N95 8GB, 5800XM, 5230, C5, iPhone 3GS, SE Xperia X10, N900, N8, SE Xperia Arc
Current Phones: Nokia N9, iPhone 4 -
Unable to load admin page asa 5512
Hi,
I have a new ASA 5512-X, out-of-the-box, which I am unable to open the admin web page on.
Laptop - Lenovo Windows 7 64 bit
Browsers - Firefox 28 & IE 11
Java is installed and correct vesrions
ASDM on the 5512 - asdm-66114.bin
ASA Ver - asa861-2-smp-k8.bin
https is enabled and I'm using IP addresses that are allowed connectivity to the 5512
When i browse to https://192.168.1.1/admin I am presented with a certificate error as expected, I accept the certificate, then the page hangs. This happens on both Firefox and IE.
Wireshark shows the TCP 3-way handshake and the TLS/SSL negotiation which is then immediately followed by the 5512 sending SSL data then a FIN,PSH,ACK packet back to my PC. then a load of TCP retransmits from both my PC and the 5512.
Now, I tried a different PC (Dell), same OS, same ver of Firefox but IE ver.9, and did not have any problems being presented with the 'Run ASDM Wizard' page.
Has anyone had a similar issue? Has anyone please got any idea what config on my PC may be at fault?
Many thanks for any suggestions and help.
CheersPlease have a look at the ssl settings on the ASA: "show run | i ssl".
You may not have strong ciphers enabled and the PC with the newer browser does not accept the default weak ciphers. I make it a habit to setup ASAs with:
ssl encryption 3des-sha1 aes128-sha1 aes256-sha1 rc4-md5
Those are all strong ciphers. -
Configuring "Guest Wi-Fi" VLAN on ASA 5512
I'm attempting to setup a new vlan on my Cisco ASA 5512 running version 8.6(1)2. This vlan will provide access for wireless "guest" AP's in my network. I have the guest vlan setup through to my switches, I'm able to dedicate a switch port to VLAN 40 and aquire an IP address in the 10.40.10.0/24 network. Below is excerpt of what I think is the relevent config information. I'm trying to route guest traffic out my "outside" interface.
Obvious to me I'm missing another command in here. Any help would be greatling appreciated. If more the running-config is needed please advise. Thanks in advance!
interface GigabitEthernet0/1.40
description Guest Wireless Network
vlan 40
nameif guestwireless
security-level 50
ip address 10.40.10.5 255.255.255.0
route outside 0.0.0.0 0.0.0.0 X.X.X.X 1 (public IP at X.X.X.X)
access-list guestwireless_access_in extended permit ip 10.40.10.0 255.255.255.0 interface outside
mtu guestwireless 1500
access-group guestwireless_access_in in interface guestwireless
dhcpd address 10.40.10.50-10.40.10.250 guestwireless
dhcpd dns 8.8.8.8 interface guestwireless
dhcpd enable guestwirelessStripped out some config pertaining to crypto and credentials
--------------Config Below-----------------------------------
: Saved
ASA Version 8.6(1)2
hostname ASA
domain-name company.local
names
interface GigabitEthernet0/0
description ISP Interface
nameif outside
security-level 100
ip address ##.##.###.### 255.255.255.248
interface GigabitEthernet0/1
no nameif
no security-level
no ip address
interface GigabitEthernet0/1.40
description Guest Wireless Network
vlan 40
nameif guestwireless
security-level 50
ip address 10.40.10.5 255.255.255.0
interface GigabitEthernet0/2
nameif inside-tempnet
security-level 0
ip address 172.29.0.252 255.255.255.0
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
shutdown
no nameif
no security-level
no ip address
interface Management0/0
shutdown
nameif management
security-level 100
no ip address
management-only
boot system disk0:/asa861-2-smp-k8.bin
ftp mode passive
clock timezone CST -6
clock summer-time CDT recurring
dns server-group DefaultDNS
domain-name company.local
same-security-traffic permit inter-interface
object network NETWORK_OBJ_10.100.10.0_24
subnet 10.100.10.0 255.255.255.0
access-list outside_access_in extended permit ip object NETWORK_OBJ_10.100.10.0_24 any
access-list inside-tempnet_access_in extended permit ip 172.29.0.0 255.255.255.0 object NETWORK_OBJ_10.100.10.0_24
access-list Split_Tunnel_List standard permit 172.29.0.0 255.255.255.0
pager lines 24
logging asdm informational
mtu outside 1500
mtu guestwireless 1500
mtu inside-tempnet 1500
mtu management 1500
ip local pool ClientVPN-DHCP-Pool 10.100.10.50-10.100.10.250 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-66114.bin
asdm history enable
arp timeout 14400
nat (inside-tempnet,outside) source static any any destination static NETWORK_OBJ_10.100.10.0_24 NETWORK_OBJ_10.100.10.0_24 no-proxy-arp route-lookup
nat (guestwireless,outside) after-auto source dynamic any interface
access-group outside_access_in in interface outside
access-group inside-tempnet_access_in in interface inside-tempnet
route outside 0.0.0.0 0.0.0.0 ##.##.###.### 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
http server enable
http 0.0.0.0 0.0.0.0 inside-tempnet
http 172.29.0.0 255.255.255.0 inside-tempnet
http redirect inside-tempnet 80
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
dhcpd address 10.40.10.50-10.40.10.250 guestwireless
dhcpd dns 8.8.8.8 interface guestwireless
dhcpd enable guestwireless
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl encryption aes256-sha1 aes128-sha1 3des-sha1
ssl trust-point ASDM_TrustPoint0 outside
ssl trust-point ASDM_TrustPoint0 inside-tempnet
webvpn
enable outside
anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
anyconnect image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 2
anyconnect profiles VPNConnect disk0:/vpnconnect.xml
anyconnect enable
tunnel-group-list enable
group-policy "GroupPolicy_VPN Connect" internal
group-policy "GroupPolicy_VPN Connect" attributes
wins-server none
dns-server value #.#.#.#
vpn-tunnel-protocol ssl-client
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Split_Tunnel_List
default-domain value company.local
webvpn
anyconnect profiles value VPNConnect type user
tunnel-group "VPN Connect" type remote-access
tunnel-group "VPN Connect" general-attributes
address-pool ClientVPN-DHCP-Pool
authentication-server-group compnay.LOCAL LOCAL
default-group-policy "GroupPolicy_VPN Connect"
tunnel-group "VPN Connect" webvpn-attributes
group-alias "VPN Connect" enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
: end -
Connecting to internet with OVI Suite
I received the message that the Ovi Suite was available to download. After replacing PC Suite with Ovi, everything seems to work well, except one crucial thing: I can no longer connect to internet using my mobile. This worked perfectly with PC Suite.
The instructions reads that in the main page, I should be able find a internet-connection at the right side. Well, I don't find this option.
The other option is to go to tools -> connect to internet. Well, this option is in the menu, but it is greyed out and not possible to select, even if my computer is not connected to the internet.
The phone model is N82.
Can anybody help with this?Dear Nokia,
Just installed the update of Ovi
This is the Sys info:-
Nokia Ovi Suite 2.0.1.35
Nokia PC Suite 7.1.40.1
PC Connectivity Solution 9.44.0.3
Connectivity Cable Driver 7.1.22.0
Nokia Ovi Suite Software Updater 2009.40.0.60128
Maps Service API 3.0.35.0
Nokia mPlatform 2.5.195
Ovi Desktop Sync Engine 1.0.0.684
Operating system:
Microsoft Windows XP 32-bit Edition, Service Pack 3
Language: English
Detected internet browsers:
- Microsoft Internet Explorer 8.0.6001.18702
Detected Bluetooth stacks:
- Microsoft (Version: 5.1.2600, Build: 5512)
There is no option for Telstra in the connection wizard of Ovi
Please fix. -
OVI Suite can't connect to internet because of pro...
I can't Sign Into Ovi in Ovi Suite, probably because I can't define the proxy settings anywhere.
Can't connect to OVI from PC Ovi Suite.
I use a proxy to connect to internet (but no need to fill proxy username/password -
example skype connection is ok)
The message error is "Nokia OVI Suite can't connect to Nokia server account..
check your internet connection"
This is my informations from Help->About Nokia Ovi Suite->System Information..:
Nokia Ovi Suite 2.2.0.241
PC Connectivity Solution 10.24.0.0
Connectivity Cable Driver 7.1.29.0
Nokia Ovi Suite Software Updater 2010.18.0.60492
Maps Service API 4.0.11.0
Nokia mPlatform 2.6.195
Ovi Desktop Sync Engine 1.3.0.32
Sistema operativo:
Microsoft Windows XP Versione 32 bit, Service Pack 3
Lingua: Italiano
Browser Internet rilevati:
- Microsoft Internet Explorer 8.0.6001.18702
- Mozilla Firefox 3.6.3 (Browser predefinito)
Stack Bluetooth rilevati:
- Microsoft (Versione: 5.1.2600, Build: 5512)
Driver USB rilevati:
- Default Hub Driver for USB 5.1.2600.5512
- EHCI eUSB Miniport Driver 5.1.2600.5512 -
Adobe cloud application manager - can not connect to internet
To ADOBE - The Adode cloud Order no is DSSY006786009DT and is current
The Adobe cloud application manager - can not connect to internet even though there is internet connection and says it might be time zone error but that is correct - Sydney Australia
Question:
1. Is anybody else having this problem
2. How do we fix
I already changed the time zone east coast US - did not change anything
Could it be a corrupt program - thus requiring to reinstall program Application manager
I am using Windows 7.
It has been like it for ten days - It asks to log in everytime I turn computer on
All programs in Creative Cloud work
Any suggestions and solution
Online help and phone help had no solutions other than what I suggested - that is reload application manager
Thanks for help
Ian ClelandThe Creative Cloud File Synching was just offline, should be online now again.
See top off: http://forums.adobe.com/community/creative_cloud/creative_cloud_connection
Maybe that was your problem. -
System failed when try connecting to internet
hi
yesterday i install arch and everything work fine but
when i tried to make bluetooth connection via network manager(bluetooth)(gnome shell) by click on 'Access the internet using your phone(DUN)' checkbox after Few moments DUN service gone timed out. then i reinstall modemmanager and at last i can create connection via bluetooth(DUN Service) . but when i clicked on connection in connection menu; after few moment system crash and a black screen with a lot Incomprehensible text show and i have to reset computer manually.
anybody can help to me ????
THQ
Last edited by hamidtb (2013-03-29 10:49:59)WonderWoofy wrote:
This might be one of the more confusing and less than clear questions I have come across here. I don't use gnome or really any of this software that you use. But from what I can decipher above, you seem to have two problems.
First, it is not connecting consistently. In order to fix this, you reinstall the software? Am I reading that right?
Second, once you do get a connection, you experience a kernel panic? This is where the kernel has an oops and cannot recover, so it dumps its contents/errors to the screen. Is this what is happening?
Basically, you need to be more clear about what you are experiencing. It would seem that English is not your first language, but that should not stop you from at least phrasing your question in a way that says more than "I click this" and "I click that". Have you checked your logs at all to see if there is anything revealing there?
hi
thank you for answer
you said right and i so sorry for it; i'm from iran and my first language is persian(farsi)
weak document and support for my language Caused to i come there
yes i reinstall modemmanager package and timeout error disappeared
before my system connect to internet a black screen show and system crashed
also i tried to make a connection via below link but i unsuccess because it not compatible with my arch
https://wiki.archlinux.org/index.php/Bl … GPRS_Howto
is possible if i install another version of linux kernel my problem solved??
where save error log ??? -
How do I connect to internet with vz access manager for iphone 4S?
I have VZ Access Manager on my laptop and want to use it to connect to internet on my new iphone 4S. How do I do this?
If you can set up an Ad Hoc wireless network from your laptop, you could use it that way. Once again VZ Access Manager will not enter into the sharing part.
Plug these search terms into Google:
set up an ad hoc network
You'll find lots of instructions.
Best of luck.
Maybe you are looking for
-
Software to record from minidisc
H friends, Do you have any experience or recommendation for a software which enables recording into I Tunes from other sources than CD, i.e. from a minisidc player..? I would also be very intersted in a software for "exact copy" recording from CD...I
-
Hello all, Have made a few UFL before via VS 2008 and have successfully registered them on client machines. However, after updating to SP2 it appears that it is using a different dll wich is the u212com.dll. It works all well and fine on my developme
-
Ok, I was listening to music from itunes last night. I turn on itunes this morning and all the music that was there the night before has disappeared! I checked my "My Music" folder and all of my music placed after the "iTunes" folder has disappeared.
-
I have the following data on a student table Regno Term1 MnMark Status xxxx 1 30 Red xxxx 2 50 Amber xxxx 3 40 Amber
-
Hi, I am trying to import C720 esprimo desktop drivers and I am trying to update the boot.wim x64. When I do that boot.wim got updated but it is not updating the distribution point. ANy help please Error: Some driver(s) can not be imported successful