Can a query view be broadcast to olap cache??

Hi,
I am trying to pre-calculate a query view to the olap cache. I do not see this option in drop down. Is it possible
Thanks

Hi,
Well the few setups of ASA + Ironport that I have seen uses an WCCP ACL on the ASA which already can define which traffic is forwarded to Ironport and which simply bypasses it and goes straight out of the ASA.
Those that need to bypass Ironport are specified in the top of the ACL with "deny" statements.
access-list WCCP line 1 deny ip host host
or
access-list WCCP line 1 deny ip host any
I am not sure if this was what you were looking to do.
- Jouni

Similar Messages

Query views are not using OLAP cache

Hi,
I am trying to pre-fill the OLAP cache with data from a query so as to improve the performance of query views.
I have read several documents on the topic, such as How to Performance Tuning with the OLAP Cache (http://www.sapadvisors.com/resources/Howto...PerformanceTuningwiththeOLAPCache$28pdf$29.pdf)
As far as I can see, I have followed the instructions and guidelines in detail on how to set up the cache and pre-fill it with data. However, when I run the query views they never use the cache. For example, point 3.4 in the abovementioned document does not correspond with my results.
I would like some input on what I am doing wrong:
1. In RSRT I have Cache mode = 1 for the specific query.
2. The query has no variables, but the following restrictions (in filter): 0CALMONTH = 09.2007, 10.2007, 11.2008 and 12.2007.
3. I have one query view with the restriction 0CALMONTH = 10.2007, 11.2008 and 12.2007.
4. I have a second query view, which builds on the same query as the first query view. This second query view has the restriction 0CALMONTH = 11.2008 and 12.2007.
5. There are no variables in the query.
6. I run the query.
7. I run the first query view, and the second query view immediately after.
8. I check ST03 and RSRT and see that cache has not been used for either of the query views.
Looking at point 3.4 in the abovementioned document, I argue that the three criteria have been fulfilled:
1. Same query ID
2. The first query view is a superset of the second query view
3. 0CALMONTH is a part of the drill-down of the first query view.
Can someone tell me what is wrong with my set-up?
Kind regards,
Thor

You need to use following process of process chain: "Attribute change run (ATTRIBCHAN)". This process needs to be incorporated into your process chains which loads data into provider on top of which your query is based.
See following links on topic how to build it:
https://help.sap.com/saphelp_nw73/helpdata/en/4a/5da82c7df51cece10000000a42189b/frameset.htm
https://help.sap.com/saphelp_nw70ehp1/helpdata/en/9a/33853bbc188f2be10000000a114084/content.htm
cheers
m./

How to Locate "Query View u2013 Selection" web item in WAD

Hi,
Where/How can i find the "Query View u2013 Selection" web item in Blank Templete of a WAD
or
From where i can install it from Business Content
Thanks

Hi,
Are you with 7.x WAD?
This option will be available with that.
Or else,after putting Analysis Item->Properties->General tab->Click "New Data Provider" icon->Select the Type dropdown as "Data Provider of Type Query View".
This will list three radio buttons ""Query View","Query" and "InfoProvider" under "Define Data Provider Type".You can select "Query View" radio button and assign Query View.
Rgds,
Murali

Copy Query View from one User to another User

Hi
I have a question that whether we can copy Query View created by an User to another User .
Please help me with some way of doing it.
Regards,
Vimarsh

Vimarsh,
Can the user not just eMail their view to their colleague?
Regards
Gill

How to understand if olap cache is used

Hi,
I am trying to understand if my query uses the olap cache or not.
First I executed the report with specific selections. After that, I executed the report again with the same selections but it took almost same time to bring the report output. There are lots of exception aggregates in my query, so i wonder if olap cache will help me or not.
So, how can I understand if the query uses the olap cache or not ? (i am using RSRT screen, with 'do not use cache' blank)
Thanks
Ozan

Hi
Check in tcode RSRT. Input your query tech name and from the properties tab, you can see if the olap cache is set to be used in the cache mode field.
You can check if the entries you are making in the cache are used, if you, also from RSRT, go to cache monitor->main memory and expand the folder "query directory".
now search for your query tech name.
a folder will appear with your query tech name if the cache mode enabled.
right-click and choose details. here you will see "read accesses" and the number will tell you how many times this entry has been read.
regards
jacob

How can I see the Query view created for a different user

Hi All,
How can a user see the View of a query created for a different user??
I would like some info about how to give access ( if it is a access problem) or tell me the steps to do that.
Regards, Federico

Hi all,
Maybe I didn't explain me as i should or maybe you dont know what is a Query View. Lets try again, showing you the steps to open a "Query view".
This way is from Bex Analyzer (Excel)
I open the Bex Analyzer and connect to the system -> Open query -> Under "Type" choose "Query View"...this is just a different view of the original query (more or least columns/rows).
This way is from Bex Web:
Once you open/execute the query, you have a ComboBox to choose the view (previously saved)
The problem that we have is that the views created for a user, can NOT be found by other user. The only user who can is the owner.
Could it be an authorization problem? or is ther any configuration possible to see it?
Thanks in advance, Federico

Query mass Broadcasting to fill OLAP cache

Hi,
I have +- 50 relative small queries that I'd like to precalculate each night (push them to the OLAP cache) as these queries are displayed together in one KPI dashboard.
I know the Bex Broadcaster is the tool that should be used but at this moment I don't know any way to schedule the precalculation for ALL queries in mass. Is there a way to Broadcast queries in mass via a certain program or via any other means?
Putting them in one workbook is an option (and having this workbook precalculated) but I was wondering if there are any other solutions ?

I have now been investigating mass broadcasting via :
1 one workbook with several queries integrated
1 webtemplate with several queries integrated
But both alternatives don't offer the option "Fill OLAP Cache" in the Bex Broadcaster. It seems this is only selectable when you start the Broadcaster for one individual query ? So my conclusion is that you need to make a settings for all queries individually ? Or is there a way to change the distribution method for webtemplates ? Quite a big dissapointment for me anyway...

Do Query Views use existing OLAP Cache or create their own

Hi, I'm looking to find out if a Query View will use the Parent Query OLAP Cache or will it create it's own?
I am imagining that it would use the query view, but create additional cache if it drilled down on a free characteristic that wasn't in the original query output. Any comments

If there are any entries in the CACHE which meets the drilldown and filter criteria for the view it will be able to make use of existing Cache.
As you mentioned for any additional drilldowns if there are not entries in the cache it will have to read from DB.

Error in Query View Saving -The standard transport system is active.You can

Hi,
I have a query in Dev system which is moved to production and i am able to edit the query in dev.But my problem is when i tried to create a view on that query and save the view, it is throwing me a error
"The standard transport system is active.You cannot save"
Any pointers on this.
Regards,
Pra

Hi
Did you get any feedback on this one?? Im facing the same message when saving a query view..
Thanks
Willem

Pre-fill the OLAP cache for a query on Data change event of infoprovider

Hi Gurus,
I have to pre-fill the OLAP cache for a query,which has bad performance.
I read a doc 'Periodic Jobs and Tasks in SAP BW'
which suggested sum steps to do this
i hav created the setting for Bex broadcasting for scheduling job Execution with data change in info provider
thereafter doc says "an event has to be raised in the process chain which loads the data to this InfoProvider.When the process chain executes the process u201CTrigger Event Data Change (for Broadcaster)u201D, an event is raised to inform the Broadcaster that the query can be filled in the OLAP cache."
how can this b done please provide with sum proper steps
Answers are always appreciated.
Thanks.

Hi
U need to create a process chain or use the existing process chain which you are using to load your current solution, just add event change process type in the process chian and inside it add the info provider which are going to be affected.
Once you are done with this go to the broadcaster and create new setting for that query...you will see the option for event data chainge in infoprovider just choose that and create the settings.
hope it helps

Impact of real time cube on query performance and OLAP cache

Hi:
We have actual and plan cubes both setup as real time cubes (only plan cube is being planned against, not actual cube) and both cubes are compressed once a day.
We are planning on implementing BIA accelerator and have questions related to query performance optimization:
1/ Is there are any query performance benefits in changing the actual cube to be a basic cube (using program SAP_CONVERT_NORMAL_TRANS) if the F table is fully compressed
2/ Can OLAP cache be leveraged for the queries run against the real time cubes e.g. actual cubes
3/ What is the impact on BIA of having the actual cube as real time (whetehr or not there is data being loaded/planned during the day in that cube)
Thank you in advance,
Catherine

1) Is there are any query performance benefits in changing the actual cube to be a basic cube (using program SAP_CONVERT_NORMAL_TRANS) if the F table is fully compressed
From the performance point of view, tha actual cubes i.e std cubes are relatively better.
2) Yes OLAP cache can be leveraged for bringing up the plan query but all the calculations are done in the planning buffer.
3) Not sure.

OLAP Cache filling using Broadcasting

Hi All,
We have two BEx queries which take more than 30 minutes to complete. One is an inventory cube query and other one is a query with a lot of exception aggregation.
In the Statistics, both queries show that around 90% execution time is at OLAP level.
We created broadcasting settings to fill OLAP cache for both the queries and scheduled in background. In RSRCACHE, we can see entries for both queries.
But the execution time still have not improved. They both are taking same time to complete execution.
Now I doubt if OLAP Cache supports non-cumulative key figures and exception aggregation or not. Is this mentioned in any documentations?
Pls let me know your suggestions.
Thanks in advance,
Regards,
Bijesh

hi,
you can carry out following checks:
1) check parameter of global and local cache, general sense the global cache size should be larger than the local cache size you can configure the cache parameters in RSCUSTV14 or simply ask basis do optimise them acc. to system usage
2) also since you you have checked RSRCACHE, try changing few option in properties change read to X(for large amt of data) by default its H
3) try changing cache mode to with swapping instead of default without swapping, in case of several app server choose mode 4
then click on environment->query mass maintainence
see if these works out
regards
laksh

How to create a query view in sap bw?

can any one please tell me how to create a query view in sap bw 3.5?

Hi,
you can do this by using Bex analyzer and WAD ..
gop through this link ..
http://help.sap.com/saphelp_nw70/helpdata/en/0e/1339427f82b26be10000000a155106/content.htm
http://help.sap.com/saphelp_nw70/helpdata/en/0d/af12403dbedd5fe10000000a155106/frameset.htm
hope this helps you ..
Reagrds,
shikha

Error while saving a query view

Hi All,
I am trying to save a query view in my favourites and it is failing with below message:
Namespace '/BIC/' must be set to 'changeable' (transaction SE06)
I have created many query view so far, this issue has just started. Could you please help us with this, as it is very urgent.
Thanks and regards,
Shashidhar.

Hi,
Please set the setting as described in note 337950, it will help to fix the issue.
solution:
Releasing the object changeability
This setting is only intended for production or test systems that are
set to not changeable. It is not suitable for development systems. For
this reason, this setting is only effective if at least one of the
conditions specified under 'Cause and prerequisites' is met.
Go to the Administrator Workbench (Data Warehousing Workbench,
transaction RSA1) -> 'Goto' -> 'Transport Connection' and choose 'Object
Changeability'. To display the function, you may have to enlarge the
window or press the arrow keys nearby.
In the following dialog box you can select the object types that you
want to be changeable, even though the system is set to not changeable.
These objects are not connected to the transport system; this means that
no transport dialog boxes are displayed. This only applies, however, if
the preconditions mentioned under 'Cause and prerequisites' are met.
First, after releasing an object type, only objects that are original,
that is, those that were created in this system can be changed. This
prevents changes to objects that were imported into the system. However,
changes to these objects may be overwritten again during a new
transport.
You can set all objects to changeable (even the ones imported into the
system) using the context menu (right mouse button), although this
setting is not recommended for the reasons mentioned above.
Thanks,
Venkat

Can not query PQH_BUDGET_DETAILS in SQL*Plus

Hi!
I can see the Positions in the Forms-Mask within EBS.
I want to write a concurrent Programm which queries some data form the positions-table.
If i klick on "Help > Diagnostics > Examine" and select "system.last_query" i can see, that the data comes from a view called: "PQH_POS_BUDGETS_V".
But if i try to query this view in SQL*Plus, it is empty.
So i had a look at how this view is build, and i found, that the base tables should be PQH_BUDGETS and PQH_BUDGET_DETAILS.
How can i query the position_id in PQH_BUDGET_DETAILS in a concurrent program or an self-writen BI Publisher Report?
If i try to query in SQL*Plus it's empty.
Who can help me with this issue?
Thank you for your help!
Best regards,
Thomas

Hi!
Thats great!
Thank you very much!
Best regards,
Thomas

Can a query view be broadcast to olap cache??

Similar Messages

Maybe you are looking for