Can't add my new license on my cisco 2500 wireless controller

hello,
i already have 25 license installed on my Cisco 2500 wireless controller.
but when i need add my new bundle license, i can't see him on my admin panel.
i following this steps for installing my new license :
1- i go on WLC panel
2- management => software activation => commands
3- i select "install license"
4- i setting a correct path
5- when i clic on "install license", i can see two following message : "File transfer operation started" and "Installation Process Completed ". but when i go on "licenses" i can't see
tanks for help

Hi Serge,
In case you have another license installed on the controller with higher license than the one that you are installing, then the license installation will fail.
In case you want to install a new license with higher number of AP count, then you can install it, then save and reboot the controller.
Also I noticed when you install a new license and the summation of the previously installed license and the newly installed license is exceeding the max allowed AP count on the controller, then the installation will fail.
In such scenario, deactivate the current license by making the evaluation license priority to high, then after that install the new license and then change the priority to medium and make the evaluation license to low in addition to the previous license.
Kind Regards
Mohammad Setan

Similar Messages

How can I add the new AP license to HA 5508 WLC?

Hi,
My customer has two 5508 WLC in HA mode and these devices have 250 AP license. Customer bought 50 AP and 50 AP license. But I could not add the license to WLC! When I check the Management>Software Activation> tab there are only two options under the tab these are "Licenses" "License Usage". There is no "Command" option in there. Also I tried add on CLI but this error log appeared " !!!! Blocked: Changing License configurations on Secondary unit is blocked !!!! "
I think this is possible when disable the HA but is there anybody know this how can I add the new 50 AP license to HA WLC without disable the HA?
Thanks,
Burhan

Hi,
Thank you for your reply.
Yes I know the controllers synchronize with the enabled license and the 250 AP license bundled with two device there is no problem.
I want to add new 50 AP license in addition 250 AP license. Because customer has 300 AP's.
As I said, When I check the Management>Software Activation> tab there are only two options under the tab these are "Licenses" "License Usage". There is no "Command" option in there.
Thanks,

Add one new license too existing licenses

Hi people,
I need to add a new license to that already existing for a customer.
Since the customer is not one of mine, I cannot produce the license.lic with all his licenses with the new in add.
So I need to send to him a .lic within just the new license; obviously, when this file is loaded, it hasn't reset the existing licences.
Is this possible by SAP Marketplace?
Moreover, can I obtain this programmatically by SBO License COM Bridge?
Thank you for your support.
Ciao.
Monica

Hi Paul, thanks for your response.
Just for check if I correctly understood your mean.
You are suggesting me the usual way to add a new licence at a mine customer and so, alternative, via:
-> https://websmp210.sap-ag.de/smb/support
-> https://websmp203.sap-ag.de
-> http://service.sap.com/user-admin
I gain the link Request license key, select the customer, select the customer system, continue over the system details and, finally, I choose the new partner solution to add.
Ok, if this is that you mean, it's not the solution for my need because:
1) the prerequisite is that the customer is one of my customers (but I suppose that I have to create he if I want to sell he a license, and this is ok)
2) when I add this new customer to mine, I haven't his current licenses dashboard, and that I'm adding to he is the first license of his dashboard.
What happen when I send he the B01_multiple.txt license file within just the license for my add-on?
Scenario 1) all his current licenses are reset and the unique license in his license manager is the mine;
Scenario 2) the new license is simply added at the current licenses in his license manager.
The request
In case of Scenario 1 - deprecated - how can I correctly to manage this kind of business?
Thanks for your availability.
Ciao. Monica

Can I add my existing, licensed apps to my list of 'Purchases' on the Mac App Store so I don't have to buy them twice?

Hello,
I was wondering if I could add my existing, licensed apps to the list of app 'Purchases' that I have on the Mac App Store.
The reason for this is that I recently suffered the inevitable hard disk failure and I had to rebuild my MacBook Pro from scratch (with the help of Time Machine and Migration Assistant, etc.). As usual, I hadn't really maintained my MBP for quite a while and things sort of got away from me, in terms of data, apps, preferences, permissions, users (my personal account, my wife's account, my old work account...), etc.
So I wanted to rebuild my MBP on a clean slate. I like having the ability to quickly download and install just the right apps that I "really" need from MAS safe in the knowledge that:
they are there (assuming they're still available through MAS) with a full description of what they do and when I bought them, etc.
they are going to be in the most up-to-date version,
I'll be able to download and install them cleanly with no corruption from years of multiple user preference changes and permissions, etc.
that they will be managed and maintained (updated) through the same mechanism,
so much more.
The benefits of having apps from MAS are easy to see when compared to going through my downloads folder and emails looking for the latest installers, working out what they're for in the first place, finding the license key in some forgotten e-mail, etc.
I am aware that I can build a clean machine and then restore just the right apps in their most up-to-date version as I had them on my backups. The one thing to say about that is that the apps may have been used and abused once too many times and their preferences, etc. may not be in the most desirable form. It's just not as elegant as the MAS solution.
I realise that not all apps, app versions, or app vendors, are available through MAS. But I still have a fair few apps currently available on MAS that were bought prior to the existence of MAS, prior to them becoming available on MAS, or were bought directly for some other reason (by mistake).
So I wondered if there was any way I could convert my legitimate licenses from simply a direct purchase to one through MAS and have those apps listed under my 'Purchases' list. It would reduce the amount of work I'd have to do, not only to rebuild my machine but also to maintain it.
I cannot find any reference or way of having this work the way I would like it to. But I was hoping that some Apple guru would enlighten me.
I have thought about the possible mechanisms something like this would need to work and I must admit I see some not insurmountable issues (not as much technical as legal or possibly logistical). I realise that MAS is a service in its own right and as such has its own Terms, Conditions and Licensing that may not be compatible with the licenses that I already have. I also realise that when I purchase an app from MAS that I'm paying for the entire service including updates and use on multiple machines that I may own, etc. Obviously I do not want to pay the full purchase cost again for the same app twice, but I am willing to pay a small conversion/upgrade fee to have it managed as part of my 'Purchases' on MAS. Think of it in the same terms as iTunes works. I can purchase music, etc. but I can also add my own CD collection and have it managed by iTunes and store it in the cloud should anything go wrong with my local machine, etc.
So if this is currently not possible, then for the Apple MAS product managers out there, consider this as a suggestion/feedback. I'd be happy to discuss my thoughts in more detail about not only how to achieve this for now but also for the future when you may add existing applications to MAS that people may have previously bought direct and would like to have managed through MAS going forward. The benefits to the users are hopefully clear, but from Apple's perspective I hope that you can see the advantages too, commercially, etc.
PS: I apologise for the wordiness of my query and overuse of 'etc.', etc.

Can I add my existing, licensed apps to my list of 'Purchases' on the Mac App Store so I don't have to buy them twice?
No. Only apps purchased from the App Store can be re downloaded for free including updates.

Can I add a new phone user to my itunes account without overriding my phone data?, can I add a new phone user to my itunes account without overriding my phone data?

Can I add a new phone user to my itunes account without overriding my phone data?

Read this
http://support.apple.com/kb/HT1495

Can't add a new event to iCal on my iMac - but the event sync's to my iPad - is this a Lion problem? iCloud is on.

Can't add a NEW EVENT to my iCal on my iMac- however the event is sync'd to my iPad with no problem. iCloud is turned on for iCal. Is this a Lion problem or something turned pff. I cannot find an answer. Help?
Williamfronsc

William,
It is a possibility that you are adding new events to your "On My Mac" calendars.
"On My Mac" calendars will not sync with iCloud. After backing up the "On My Mac" calendars, and ensuring that all events are duplicated on your iCloud calendars you can delete any "On My Mac" calendars.
For further troubleshooting advice read iCloud: Troubleshooting iCloud Calendar.

I can't add a new event to my calendar on iPhone.

I can't add a new event to my calendar on iPhone. The plus sign is greyed out and even when I try it with Siri it says "Sorry. I can't do that right now". I did my due diligence and searched all over the forums and internet and I can't fix this. There was a listing in a forum where a lady had this same symptom but it looks like toggling iCloud worked for her. Not for me. I went into Settings>iCloud and turned off Calendar and then turned it back on. Still nothing. I even went to iCloud Backup and turned it on then back off and still nothing. Anyone have any suggestions? Thanks!

See if you can go to your Calendars App and select a previous event to see what Calendar the event was added to (iCloud or Yahoo). After that is determined you can go to www.iCloud.com or calendar.yahoo.com and add the event there to see if it will populate on your device. Another troubleshooting step is deleting the iCloud account from your device and also deleting the Yahoo account. Then check to see if you can add an event without it syncing to a email. If you can then it may have just been a bug and you can add both accounts back and try adding the event again. I would also recommend only using one service to sync your Contacts, Calendars, Reminders, etc. Such as either iCloud only or Yahoo only, as using multiple accounts means your data is spread around and can be hard to isolate when something goes wrong.

ICal Lion is infuriating. How can I add a new event in a chosen calendar without having to create it in my default then edit it?

iCal Lion is infuriating. How can I add a new event in a chosen calendar without having to create it in my default then edit it?

We are all entitled to our own opinions. So I respect you there brother
But then again, Apple has its own basis. iOS is what's selling like pancakes not Macs, so if the gazillions out there are using iOS device and have gotten used to the calendar in their iOS devices. Wouldn't you think it made sense if Lion has the same calendar look and feel?
Everything was considered and weighthed when they developed Lion. They even mentioned it in the press, They were blown away with the success of iOS so they are extending it to OSX.
Quite frankly, I like the old iCal but yeah I don't expect anything in SL to stay in Lion otherwise it'll be another Cat name related to Leopard
People should start looking at this perspective and not get STUCK in the old OS.

How can I add a new filed to standart SAP Screen

Hi eveybody,
I am using ima11 t-code and I need to add A new screen field to standart SAP screen(program No SAPLAIA1 Screen:1001 ).I have found five user-exits(AAIR0001,AAIR0002A,AIR0003,AAIR0004,AAIR0006) but there is no screen-exit. How can I add a new filed to standart SAP Screen.Is it possible? If it is possible, how can I do that?

hi
yes you can add a search help for a filed on the screen
but you need to find out for the USER EXIT available for that T-CODE
because it is a standard T-CODE we can't add code directly to the standard T-code
1st we need to find out for a user exit and then add code in that user exit
reward if usefull

How can i add a new 53 rd week to calendar

Hi All,
we have requirment i need to add a new week to fiscal year 2011 for septemebr,2011
Please let me know how can i add a new week to this month,
Thanks & regards,
Chand

Hi All,
we have requirment i need to add a new week to fiscal year 2011 for septemebr,2011
Please let me know how can i add a new week to this month,
Thanks & regards,
Chand

How can i add a new characteristic to Sap standard InfoObject?

Hi Experts,
Please anyone let me know how can I add a new characteristic or a key figure into an SAP standard InfoObject in order to add it to the standard InfoCube? The situation is I would like to add region and business unit to the characteristics of the Industrial Hygiene and Safety. After that, I would like to add them to the InfoCube called Accidents: Person Involved [0EIH_C02] that is located in the MultiProvider called Accidents: Complete View [0EIH_MC01]. Is it feasible to do this way?
I just learned the BW/BI, so please help me with this. I would really appreciate your responses.
Thanks,
-Napadol

Hi Napadol,
To add a attribute in a char:
1) Go to info object/char in change mode and add the additional attribute you want and select navigational attribute in attribute tab if you want. (Create these additional attribute first in info object catalouge)
2) Activate the Object/Char
3) open info cube in change mode and pick the characteristic from left panel to info cube dimension.
4) Activate infocube.
5) Go to multi provider add the char in one of the dimension and do identification for this char and activate.
Regards,
Kams

How can I add a new entry for determining a requirement type

Dear Friends,
How can I add a new entry for determining a requirement type
via Item Category + MRP type, I see no new entries selection.
This is in Avb Check & TOR-> TOR-> Determination of req type using transaction.
Please help.
Regards
Ravi.

Availability Check and Transfer of Requirements > Transfer of Requirements > Define Requirements Types ?
Just one node above?
Never mind, you need to add entry on item category:S

How can I add a new line item for production order?

HI all,
How can I add a new line item for production order through BAPI/FM? Thanks in advance.

Hi Mil,
Unfortunetly SAP is not in front of me.
But if possible go to BAPI transaction , check for any production order's bapi for CHANGE purpose. Where you will be able to add your new line.
Reward if useful!

How can I add a new column in compress partition table.

I have a compress partition table when I add a new column in that table it give me an error "ORA-22856: CANNOT ADD COLUMNS TO OBJECT TABLES". I had cretaed a table in this clause. How can I add a new column in compress partition table.
CREATE TABLE Employee
Empno Number,
Tr_Date Date
COMPRESS PARTITION BY RANGE (Tr_Date)
PARTITION FIRST Values LESS THAN (To_Date('01-JUL-2006','DD-MON-YYYY')),
PARTITION JUNK Values LESS THAN (MAXVALUE));
Note :
When I create table with this clause it will allow me to add a column.
CREATE TABLE Employee
Empno Number,
Tr_Date Date
PARTITION BY RANGE (Tr_Date)
PARTITION FIRST Values LESS THAN (To_Date('01-JUL-2006','DD-MON-YYYY')),
PARTITION JUNK Values LESS THAN (MAXVALUE));
But for this I have to drop and recreate the table and I dont want this becaue my table is in online state i cannot take a risk. Please give me best solution.

Hi Fahed,
I guess, you are using Oracle 9i Database Release 9.2.0.2 and the Table which you need to alter is in OLTP environment where data is usually inserted using regular inserts. As a result, these tables generally do not get much benefit from using table compression. Table compression works best on read-only tables that are loaded once but read many times. Tables used in data warehousing applications, for example, are great candidates for table compression.
Reference : http://www.oracle.com/technology/oramag/oracle/04-mar/o24tech_data.html
Topic : When to Use Table Compression
Bug
Reference : http://dba.ipbhost.com/lofiversion/index.php/t147.html
BUG:<2421054>
Affects: RDBMS (9-A0)
NB: FIXED
Abstract: ENH: Allow ALTER TABLE to ADD/DROP columns for tables using COMPRESS feature
Details:
This is an enhancement to allow "ALTER TABLE" to ADD/DROP
columns for tables using the COMPRESS feature.
In 9i errors are reported for ADD/DROP but the text may
be misleading:
eg:
ADD column fails with "ORA-22856: cannot add columns to object tables"
DROP column fails with "ORA-12996: cannot drop system-generated virtual column"
Note that a table which was previously marked as compress which has
now been altered to NOCOMPRESS also signals such errors as the
underlying table could still contain COMPRESS format datablocks.
As of 10i ADD/SET UNUSED is allowed provided the ADD has no default value.
Best Regards,
Muhammad Waseem Haroon
[email protected]

How can I add a new column to Grid view under Tests tab

I understand in "ORACLE Test manager for web Applications", the Grid view under Tests tab should be customised.
How can I add a new column to Grid view under Tests tab? Thanks Katherine

I don't think this is possible.
Regards,
Jamie

Can't add my new license on my cisco 2500 wireless controller

Similar Messages

Maybe you are looking for