Does un-checking "Allow Debuging" in VI properties- execution improves overall application performance?

Does un-checking "Allow Debuging" in VI properties->execution improves overall application performance?

> Does un-checking "Allow Debuging" in VI properties->execution improves
> overall application performance?
Yes, though it is hard to predict by how much. When debugging is
enabled, after each node on the diagram there will be a small amount of
compiled code to test if the VI has a probe, a breakpoint, execution
hiliting, or the pause button is pressed. The code is quite small,
about two or three instructions, but if you have twenty nodes in a loop
and the nodes are doing simple math, these instructions could be 25%
overhead. For more complex nodes or datatypes, these instructions turn
into a fraction of a percent.
Turn it off and measure. If you have other performance problems, read
the documentation on the profiler and use it to help you find yo
ur
bottlenecks.
Greg McKaskle

Similar Messages

The 'Do Not Email' when sharing a Document does not always allow a check mark to be entered.

The 'Do Not Email' when sharing a Document does not always allow a check mark to be entered.
Just wanted to report this. I have not checked to see if it has been previously submitted. The issue
is intermittent.

I think this happens because you need to send e-mail when you do the first contact with the user. Tellimg him who you are and etc.
When you already "know" that user, u can check the box.
Hope it helps,
Andrey Farias

How does APEX check for null values in Text Fields on the forms?

Hello all,
How does APEX check for null values in Text Fields on the forms? This might sound trivial but I have a problem with a PL/SQL Validation that I have written.
I have one select list (P108_CLUSTER_ID) and one Text field (P108_PRIVATE_IP). I made P108_CLUSTER_ID to return null value when nothing is selected and assumed P108_PRIVATE_IP to return null value too when nothign is entered in the text field.
All that I need is to validate if P108_PRIVATE_IP is entered when a P108_CLUSTER_ID is selected. i.e it is mandatory to enter Private IP when a cluster is seelcted and following is my Pl/SQL code
Declare
v_valid boolean;
Begin
IF :P108_CLUSTER_ID is NULL and :P108_PRIVATE_IP is NULL THEN
v_valid := TRUE;
ELSIF :P108_CLUSTER_ID is NOT NULL and :P108_PRIVATE_IP is NOT NULL THEN
v_valid := TRUE;
ELSIF :P108_CLUSTER_ID is NOT NULL and :P108_PRIVATE_IP is NULL THEN
v_valid := FALSE;
ELSIF :P108_CLUSTER_ID is NULL and :P108_PRIVATE_IP is NOT NULL THEN
v_valid := FALSE;
END IF;
return v_valid;
END;
My problem is it is returning FALSE for all the cases.It works fine in SQL Command though..When I tried to Debug and use Firebug, I found that Text fields are not stored a null by default but as empty strings "" . Now I tried modifying my PL/SQL to check Private_IP against an empty string. But doesn't help. Can someone please tell me how I need to proceed.
Thanks

See SQL report for LIKE SEARCH I have just explained how Select list return value works..
Cheers,
Hari

How do I delete apps in os5? I press and hold the icon and they all begin to shake but the little x does not appear allowing me to delete.

How do I delete apps in os5? I press and hold the icon and they all begin to shake but the little x does not appear allowing me to delete.

You can't delete any of the Apple built-in apps e.g. Music, App Store, Game Centre etc. If you don't get the 'x' on any of the apps that you've downloaded then check that Settings > General > Restrictions > Deleting Apps isn't set 'off'

How do I re-install Bonjour on OS 10.4.11? I have my original disks, but does basic install allow me to just install Bonjour or all original software?

How do I re-install Bonjour on OS 10.4.11? I have my original disks, but does basic install allow me to just install Bonjour or all original software?

Download it here...
http://support.apple.com/kb/DL1046
Check out the new remodeled MacOSG website! 24-hour Apple-related news & support.
 MacOSG: An Apple User Group  iTunes: MacOSG Podcast  Follow us on Twitter: MacOSG

Change selection criteria or check allowance for marking

Hi,
I have executed the costing in CK11N and saved the result. The costing run was successful without any error.
When I want to Mark the cost in CK24, I am getting the below error. Kindly help to resolve this issue.
Change selection criteria or check allowance for marking
Message no. CKCC140
Diagnosis
No data was selected for marking.
Possible causes:
There is insufficient data in the selection screen to select the required cost estimates.
The organizational measure was not carried out, or it was issued with a different costing variant to that of the cost estimates ( Marking Allowance).
All the cost estimates contain errors.
The cost estimates have already been marked or released.
For detailed information, call up the log.
thanks and regards
Murugesan

Dear Murugesan,
First ensure in CK11N,you have saved the cost estimate without any error,the signal showing with green colour.
Then in CK24,first take a test run for marking and then without the check box for test run.
Before Executing this T Code for marking,click on marking allowance and ensure for the period,company code and the same
costing variant and costing version,it shows green colour which indicates alloed for marking and release,otherwise,just click on
your company code,enter the costing variant and costing version and save the datas.
This should be done only once during the period begining.
Once after doing this,ensure you have complete authorization for marking and release.
Check and revert back.
Regards
Mangalraj.S

HT204150 Does iOS 6 allow you to browse groups? I could do it before with iOS 5 on my 4S. Now I can't.

Does iOS 6 allow you to browse groups? I could do it before with iOS 5 on my 4S. Now I can't.

If you check all the groups then you will see the combined contacts in all of the groups. If you want to see (browse) the contacts in, for example, just one group, only check this one group and tap done. If you check two groups and tap Done you will see the combined contacts belonging to these two groups.
Try checking a single group and uncheck all others, tap Done and you'll see what I mean.

I find it ABSOLUTELY unacceptable that since recently safari opens up random "commercial websites" without me clicking on any link. And it does that without allowing me to go (back) to the site I really clicked on. STOP THAT!!!!!!

I find it ABSOLUTELY unacceptable that since recently safari opens up random "commercial websites" without me clicking on any link. And it does that without allowing me to go (back) to the site I really clicked on. STOP THAT!!!!!!

There is no need to download anything to solve this problem. You may have installed a variant of the "VSearch" ad-injection malware. Follow Apple Support's instructions to remove it.
If you have trouble following those instructions, see below.
Malware is always changing to get around the defenses against it. This procedure works as of now, as far as I know. It may not work in the future. Anyone finding this comment a few days or more after it was posted should look for a more recent discussion, or start a new one.
The VSearch malware tries to hide itself by varying the names of the files it installs. To remove it, you must first identify the naming pattern.
Triple-click the line below on this page to select it, then copy the text to the Clipboard by pressing the key combination command-C:
/Library/LaunchDaemons
In the Finder, select
          Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.
A folder named "LaunchDaemons" may open. Look inside it for two files with names of the form
          com.something.daemon.plist
and
           com.something.helper.plist
Here something is a variable string of characters, which can be different in each case. So far it has always been a string of letters without punctuation, such as "cloud," "dot," "highway," "submarine," or "trusteddownloads." Sometimes it's a meaningless string such as "e8dec5ae7fc75c28" rather than a word. Sometimes the string is "apple," and then you must be especially careful not to delete the wrong files, because many built-in OS X files have similar names.
If you find these files, leave the LaunchDaemons folder open, and open the following folder in the same way:
/Library/LaunchAgents
In this folder, there may be a file named
          com.something.agent.plist
where the string something is the same as before.
If you feel confident that you've identified the above files, back up all data, then drag just those three files—nothing else—to the Trash. You may be prompted for your administrator login password. Close the Finder windows and restart the computer.
Don't delete the "LaunchAgents" or "LaunchDaemons" folder or anything else inside either one.
The malware is now permanently inactivated, as long as you never reinstall it. You can stop here if you like, or you can remove two remaining components for the sake of completeness.
Open this folder:
/Library/Application Support
If it has a subfolder named just
           something
where something is the same string you saw before, drag that subfolder to the Trash and close the window.
Don't delete the "Application Support" folder or anything else inside it.
Finally, in this folder:
/System/Library/Frameworks
there may an item named exactly
            v.framework
It's actually a folder, though it has a different icon than usual. This item always has the above name; it doesn't vary. Drag it to the Trash and close the window.
Don't delete the "Frameworks" folder or anything else inside it.
If you didn't find the files or you're not sure about the identification, post what you found.
If in doubt, or if you have no backups, change nothing at all.
The trouble may have started when you downloaded and ran an application called "MPlayerX." That's the name of a legitimate free movie player, but the name is also used fraudulently to distribute VSearch. If there is an item with that name in the Applications folder, delete it, and if you wish, replace it with the genuine article from mplayerx.org.
This trojan is often found on illegal websites that traffic in pirated content such as movies. If you, or anyone else who uses the computer, visit such sites and follow prompts to install software, you can expect more of the same, and worse, to follow. Never install any software that you downloaded from a bittorrent, or that was downloaded by someone else from an unknown source.
In the Security & Privacy pane of System Preferences, select the General tab. The radio button marked Anywhere should not be selected. If it is, click the lock icon to unlock the settings, then select one of the other buttons. After that, don't ignore a warning that you are about to run or install an application from an unknown developer.
Then, still in System Preferences, open the App Store or Software Update pane and check the box marked
          Install system data files and security updates (OS X 10.10 or later)
or
          Download updates automatically (OS X 10.9 or earlier)
if it's not already checked.

Snippet (allow debugging ... comportement ??)

Je remarque avec LV2013 un éventuel soucis avec la fonctionnalité "VI Snippet".
Quand je crée un "Snippet" au départ d'un VI dans lequel "allow debugging" est OFF
... quand je "re-dépose" le dit snippet sur un BD vierge .... "allow debugging" est ON
J'ai fait la manip plusieurs fois
- je place "allow debugging" OFF à la création du snippet
(le VI sauvegardé et ensuite rechargé en tant que fichier conserve bien "allow debugging" OFF)
- mais le snippet ... replacé sur un BD .... m'indique toujours "allow debugging ON"
un (ou plusieurs) d'entre vous peut-il confirmer (LV2013)
merci.
EDIT
pour être (encore) plus clair ... voici la manip à exécuter :
a) créer un VI (peu importe)
b) placer "allow debugging" OFF
c) sauvegarder le VI
d) fermer le VI
e) re-charger le VI
f) vérifier que "allow debugging" est bien OFF .... oui, il est OFF (normal)
g) créer un Snippet de ce VI
h) sauvegarder ce Snippet
i) fermer le VI
j) ouvrir un VI vierge
k) y déposer le dit snippet (créé en -g- )
l) .... allow debugging est "ON" (???)
Résolu !
Accéder à la solution.

Bonjour Benjamin,
merci pour ta réponse.
Un snippet est du code ... sous une forme différente ... et à chaque code correspond une certain nombre de paramètres.
@Benjamin : " cette notion est lié à un VI dans l'environnement de développement LabVIEW."
oui ... et quand je glisse un snippet sur mon BD ... justement .... ce snippet devient instantanément du code dans l'environnement de développement LabVIEW.
mais ... ce code n'est plus configuré conformément au code d'origine.
Dans le même ordre d'idée ....
Pourquoi un snippet conserve-t-il toutes les autres caractéristiques du code d'origine (en rapport avec cet environnement de développement)
.... mais pas "allow debugging". (??)
Pourquoi, alors, dans un snippet, ne pas mettre tous les paramètres de "vi properties" à ON ou OFF d'office.
Un snippet est une "photo" d'un code (au sens d'une transposition ... rien avoir avec l'extension png).
Et "un code" est caractérisé par un ensemble de fonctions et par "son" environnement ... qui lui est propre.
Un snippet doit conserver la totalité des paramètres de cet environnement.
Ce qu'il fait parfaitement .... sauf pour "allow debugging". (seul paramètre qui est mis à la poubelle et transformé en constante "ON")
Pour moi, je ne parlerai pas de "bug" ... mais c'est un manquement ... un comportement illogique et incohérent

HT1444 I am using Mac os x 10.5.8 does this version allow for an upgrade to mountain Lion

I am currently using mac os x 10.5.8 Does this version allow for an upgrade to Mountain Lion?

Snow Leopard Purchase
If you are unsure exactly what year your Mac is, check the model number.
Model Numbers
You also might want to check application compatability since PowerPC applications aren't supported.
Application Compatibility
If you can't upgrade to Mountain Lion, here are the requirements for Lion.
Computer Compatibility - Lion
If you have applications that you want to use that aren't compatible, you can retain Snow Leopard and create a new partition to install Mountain Lion on.

HT3819 Does home sharing allow you to transfer music between libraries. For example, can i pull music from my daughters library onto mine ?

Does home sharing allow me to transfer music between libraries? Can my daughter, wife and I share music?

Hello matt811
If you are having issues with transferring music through Home Sharing, check out the following article that will assist with troubleshooting the issue. Also check out the other article that will give some alternatives to transferring media to a new computer.
Troubleshooting Home Sharing
http://support.apple.com/kb/ts2972
iTunes: How to move your music to a new computer
http://support.apple.com/kb/ht4527
Thanks for using Apple Support Communities.
Regards,
-Norm G.

Does home sharing allow me to share my iTunes library with other users on the same imac

Does home sharing allow me to share my iTunes library with other users on the same imac?

Apparently so (as long as each user operates out of a different Mac User account).
After setting up home sharing in the various different user accounts on the Mac, you need to have iTunes open in the account that you want to Home Share from.
Now use fast User Switching to get into the account that you want to Home Share to. Launch iTunes in there. The library in the other account should appear as shared for you.

Does home sharing allow my husband and I to share our itunes content? If so, how do we do that since it requires the use of the same Apple ID and password on each device to do so. His itunes is linked to his email and mine is linked to my email...

Does home sharing allow my husband and I to share our iTunes content? If so, how does this work? From what I've read to use home sharing the devices/computers all require the same Apple ID and password. My husbands iTunes is linked to his email/password and mine is my email/password. So if that's the case how to we go about sharing? God I hope that makes sense.

All apps are forever tied to the Apple ID that bought them. To stop your id from popping up, you need to delete the apps on his phone, and then repurchase them under his account.

PO creation-ME21n-Why SAP does not check company code and Plant relation

Hi All,
Does someone know, why SAP does not check Plant and company code relation at the time of PO creation or how can we put validation between plant and company code at the time of PO creation.
<b>Example:</b> Suppose i have a company 0001 which is assinged to Plant 0001. when i am creating a PO with another company code 0002(Entering at header level-Org, data) and using Plant 0001 at line item level. SAP does not do this validation.
How can we put this check in place?
Thanks in advance.
Deepak

Hello Deepak,
There are three types of purchasing
- Company code specific :You need to assign company code to Pur organization
- Plant specific : You must assign plant to pur organization
- Cross company purchasing: No assignment between company code and pur organization.
In the case 3, the system will not check company code and plant relationship, but it will check plant and pur organization specific.
The following is the copy of sap help text:
You can assign a purchasing organization to one company code. This is company-specific purchasing.
You can assign a purchasing organization to no company code. This purchasing organization can then procure for all plants assigned to it, irrespective of the company code to which the plant belongs.
Since each plant must be assigned to a company code, the company code can be determined via the plant in each procurement transaction, even if the procuring purchasing organization is not assigned to a company code.
A purchasing organization must be assigned to one or more plants. This is plant-specific purchasing.
Now, check your company-code and purchase organization assignment.
Hope this helps.
Regards
Arif Mansuri

Vl01n for so does not check batch management

batch management on the mm was not initially checked.
was checked after the material was put on the so.
unrestricted batch stock does exist
attempt to vl01n for that line creates a delivery but does not check batch management under material tab
what needs done to get the delivery to inherit the batch management check?

Dear Starz,
I guess according to SAP standard - The indicator cannot be changed if stocks exist in either the current period or in the previous period.
However the same would be applicable as soon as you post the new stock after changing the material master record.
Hope this helps...
Give points if useful...
Thanks,
Jignesh Mehta

Does un-checking "Allow Debuging" in VI properties- execution improves overall application performance?

Similar Messages

Maybe you are looking for