EEM script to alert on IP SLA failures
I have the following IP SLA set up and would like to do the following. I would like to have a log entry if any of the below have a failure and then send an email alerting to that failure. Is there a way to do this with EEM?
ip sla 1010
udp-jitter 64.xxx.xxx.xxx 3456 num-packets 30 interval 25
history hours-of-statistics-kept 24
ip sla schedule 1010 life forever start-time now
ip sla 1011
tcp-connect 64.xxx.xxx.xxx 2000
history hours-of-statistics-kept 24
ip sla schedule 1011 life forever start-time now
ip sla 1012
icmp-echo 64.xxx.xxx.xxx
frequency 30
history hours-of-statistics-kept 24
history distributions-of-statistics-kept 10
ip sla schedule 1012 life forever start-time now
Thanks,
Mike
Thanks that is very helpful. Now what about something like this?
From below I would like to alert if there is a failure (see the bold)
IP_SLA_2821#show ip sla stat 1020
IPSLAs Latest Operation Statistics
IPSLA operation id: 1020
Type of operation: udp-jitter
Latest RTT: 23 milliseconds
Latest operation start time: 14:25:34.377 EDT Fri Aug 24 2012
Latest operation return code: OK
RTT Values:
Number Of RTT: 30 RTT Min/Avg/Max: 23/23/33 milliseconds
Latency one-way time:
Number of Latency one-way Samples: 30
Source to Destination Latency one way Min/Avg/Max: 9/10/16 milliseconds
Destination to Source Latency one way Min/Avg/Max: 13/13/23 milliseconds
Jitter Time:
Number of SD Jitter Samples: 29
Number of DS Jitter Samples: 29
Source to Destination Jitter Min/Avg/Max: 0/1/6 milliseconds
Destination to Source Jitter Min/Avg/Max: 0/1/10 milliseconds
Packet Loss Values:
Loss Source to Destination: 0 Loss Destination to Source: 0
Out Of Sequence: 0 Tail Drop: 0
Packet Late Arrival: 0 Packet Skipped: 0
Voice Score Values:
Calculated Planning Impairment Factor (ICPIF): 0
Mean Opinion Score (MOS): 0
Number of successes: 33
Number of failures: 0
Operation time to live: Forever
Similar Messages
-
Simple EEM script that references SLA but is inconsistent?
Hi,
Just a little confused here..... I can do the exact commands in the EEM script directly and it does what I need it to do. However, the script, when triggered, with the "EXACT" same commands sometimes works / sometimes not. Arrrgghhh! So, here is the script:
event manager applet Virtual-PPP1_Ping
event syslog pattern "TRACKING-5-STATE: 1 ip sla 1 reachability Up->Down"
action 010 cli command "enable"
action 011 cli command "clear vpdn tunnel l2tp all" pattern "[confirm]"
action 012 cli command "confirm"
action 020 cli command "conf t"
action 030 cli command "int Virtual-PPP1"
action 040 cli command "shut"
action 045 wait 3
action 050 cli command "no shut"
action 060 cli command "end"
Basically what happens is that the Virtual-PPP1 interface sometimes loses it's ip address through IPCP. So, the L2TP tunnel is still up, BUT, the Virtual-PPP1 interface loses it's assigned IP when I check the interface as it shows "unassigned".
Ideas?
Thanks for the help.
JasonTry this instead:
event manager applet Virtual-PPP1_Ping
event syslog pattern "TRACKING-5-STATE: 1 ip sla 1 reachability Up->Down" maxrun 30
action 010 cli command "enable"
action 011 cli command "clear vpdn tunnel l2tp all" pattern "confirm"
action 012 cli command "confirm"
action 020 cli command "conf t"
action 030 cli command "int Virtual-PPP1"
action 040 cli command "shut"
action 045 wait 3
action 050 cli command "no shut"
action 060 cli command "end" -
How to shut no shut interface of switch using(EEM) Script for 3560 switch
Dear community experts,
I'm new for creating scripting for EEM and below is my situation, need your support.
Present I'm using 3560 switch, one of the switch port(FA0/1) has added Cisco Access point(PoE), actually what happening daily this Access point getting struct when I'M doing the switch port (FA0/1) shut then no shut it is working fine .
So my question is i need script, that should continuously ping the IP off the Access point if the IP will drop 4 packets the switch do shut and then no shut for that I need the script, Please help me.
if it is not possible please provide the batch file, which will ping the particular IP if 4 packet drops it will telnet the switch and go to the interface do shut no shut
Note:
instead of mentioned 3560, I mentioned 2960 now corrected it please provide the script.This should work:
ip sla 1
icmp-echo 10.10.10.1
frequency 15
ip sla schedule 1 life forever start now
ip sla enable reaction-alerts
ip sla reaction-configuration 1 react timeout action-type trapOnly threshold-type consecutive 4
event manager applet reset-ap
event ipsla operation-id 1 reaction-type timeout
action 1.0 cli command "enable"
action 2.0 cli command "config t"
action 3.0 cli command "int fa0/1"
action 4.0 cli command "shut"
action 5.0 cli command "no shut"
action 6.0 cli command "end" -
Hi,
I'm trying to email an alert by eem script when a catalyst 6807 rises a syslog message for an environment alarm (ex: power down). I use the attached script but when i want to add the syslog message in body email (line 83) something is wrong and i can't fixed the error : catalyst try to execute the syslog message (see email).
Same error for a catalyst 4507 4506 Sup 6L-E 10GE IOS 15.2(1)E but the same script works for a catalyst 4506 Sup 6L-E 10GE IOS 15.0(2)SG.
Any ideas ?
ThanksHi,
I found my mystake. In the script, I commented the command "enable" and thus show commands were not recognized by cli. The script has always worked well, "Invalid input" was the result of show command. For ios 15.2, i need to gain enable level.
So I suspect a different behavior between versions 15.0 and 15.2 for running level of tcl script. -
I have an EEM script (below) and I have two problems.
1) Line action 4.5 gets a "%Error opening bootdisk:blackhole (File or Directory already in use)"
2) Line 5.0 - 5.5 get "Line has invalid autocommand "sh mls cef hardware module 4 | append sup-bootdisk:blackhole"
Any ideas to get me on my way?
thanks!
jimI'm guessing you'd get the same errors if you ran these commands manually in this order one after other (i.e., you pasted them into the CLI). This might just be a limitation of the file system. What you might do is conver this to Tcl so you don't need to use the CLI to store the output (or at least open the file once).
You can use the tool at http://www.marcuscom.com/convert_applet/ to convert your applet to Tcl. A simple modification would then be to remove the append bits, and store the $_cli_result into an accumulator buffer. At the end, do the email of that buffer. -
Monitoring dual core (Supervisor Engine 7-E) through EEM Script.
Hi,
I have a Cisco Catalyst 4500E Supervisor Engine 7-E and configured an EEM Script to monitor the dual core CPU Utilization through PRTG Network Monitor.
event manager applet dualcore authorization bypass
event timer cron cron-entry "* * * * 0-6"
action 100 cli command "en"
action 120 cli command "show process cpu | include five"
action 220 regexp "Core 0: CPU utilization for five seconds: ([^%]+)%; one minute: ([^%]+)%; five minutes: ([^%]+)%.*" $_cli_result result c0cpu5sec c0cpu1min c0cpu5min
action 240 if $_regexp_result eq 1
action 260 end
action 320 regexp "Core 1: CPU utilization for five seconds: ([^%]+)%; one minute: ([^%]+)%; five minutes: ([^%]+)%.*" $_cli_result result c1cpu5sec c1cpu1min c1cpu5min
action 340 if $_regexp_result eq 1
action 360 end
action 440 cli command "config t"
action 441 cli command "snmp mib expression owner cisco name c0cpu5sec"
action 442 cli command "expression $c0cpu5sec"
action 443 cli command "snmp mib expression owner cisco name c0cpu1min"
action 444 cli command "expression $c0cpu1min"
action 445 cli command "snmp mib expression owner cisco name c0cpu5min"
action 446 cli command "expression $c0cpu5min"
action 550 cli command "config t"
action 551 cli command "snmp mib expression owner cisco name c1cpu5sec"
action 552 cli command "expression $c1cpu5sec"
action 553 cli command "snmp mib expression owner cisco name c1cpu1min"
action 554 cli command "expression $c1cpu1min"
action 555 cli command "snmp mib expression owner cisco name c1cpu5min"
action 556 cli command "expression $c1cpu5min"
action 600 cli command "end"
end
It works fine but on the logging buffer there are a lot of %SYS-5-CONFIG_I: Configured from console by on vty0 (EEM:moncores) messages -one per minute- here an example:
Oct 29 17:54:01: %SYS-5-CONFIG_I: Configured from console by on vty0 (EEM:dualcore)
Oct 29 17:55:01: %SYS-5-CONFIG_I: Configured from console by on vty0 (EEM:dualcore)
Oct 29 17:56:01: %SYS-5-CONFIG_I: Configured from console by on vty0 (EEM:dualcore)
Oct 29 17:57:01: %SYS-5-CONFIG_I: Configured from console by on vty0 (EEM:dualcore)
I considered to use the logging suppress duplicates command to prevent the consecutive logging of more than one copy of the same system logging (syslog) message but it is only available to the Cisco IOS XR.
Someone could help me to determine if it is possible to avoid this messages through Embedded Syslog Manager, I tried to do that but
I was not successful.
Regards,
~SergioHi,
I did transitioned CLI actions to the EXPRESSION-MIB SNMP but I could not receive anything information about the dualcore utilization on the PRTG Network Monitor and received a lot of %HA_EM-7-FMFD_SNMP_ERRCODE: fh_fd_snmp_errcode: Error status: 6 NO_ACCESS_ERROR: 1. messages on the WS-C4507.
Considering the initial EEM script, could ypu help me to avoid the %SYS-5-CONFIG_I: Configured from console by on vty0 (EEM:moncores)
messages using Embedded Syslog Manager.
Here some snmpwalk to validate that I could not get the OIDs to monitor both cores.
STEP 1 Only one value is given because there is only one physical cpu.
cpmCPUTotalPhysicalIndex
1.3.6.1.4.1.9.9.109.1.1.1.1.2
C:\usr>snmpwalk -v 2c -c m4nc4rc0 10.20.91.2 1.3.6.1.4.1.9.9.109.1.1.1.1.2
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.2.4000 = INTEGER: 4000
STEP 2
entPhysicalName
1.3.6.1.2.1.47.1.1.1.1.7
C:\usr>
C:\usr>snmpwalk -v 2c -c m4nc4rc0 10.20.91.2 1.3.6.1.2.1.47.1.1.1.1.7.4000
SNMPv2-SMI::mib-2.47.1.1.1.1.7.4000 = STRING: "Linecard(slot 4)"
#sh mod
Chassis Type : WS-C4507R+E
Power consumed by backplane : 40 Watts
Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+------------------+-----------
1 18 10GE (X2), 1000BaseX (SFP) WS-X4606-X2-E JAE151904JC
2 24 1000BaseX (SFP) WS-X4624-SFP-E JAE152001AE
4 4 Sup 7-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7-E CAT1522L0G1
5 48 10/100/1000BaseT (RJ45)V, Cisco/IEEE WS-X4548-GB-RJ45V JAE12067N8K
M MAC addresses Hw Fw Sw Status
--+--------------------------------+---+------------+----------------+---------
1 e8b7.4880.e5db to e8b7.4880.e5ec 1.2 Ok
2 e8b7.48cc.6167 to e8b7.48cc.617e 1.2 Ok
4 4055.39d7.76c4 to 4055.39d7.76c7 1.0 15.0(1r)SG2 03.01.01.SG Ok
5 001e.f7da.d290 to 001e.f7da.d2bf 4.1 Ok
Mod Redundancy role Operating mode Redundancy status
----+-------------------+-------------------+----------------------------------
4 Active Supervisor SSO Active
STEP 3
cpmCPUTotal1minRev
1.3.6.1.4.1.9.9.109.1.1.1.1.7
C:\usr>snmpwalk -v 2c -c m4nc4rc0 10.20.91.2 1.3.6.1.4.1.9.9.109.1.1.1.1.7
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.7.4000 = Gauge32: 9
C:\usr>
ADDITIONAL INFORMATION
C:\usr>
C:\usr>snmpwalk -v 2c -c m4nc4rc0 10.20.91.2 1.3.6.1.2.1.90
SNMPv2-SMI::mib-2.90.1.1.1.0 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.1.2.0 = Gauge32: 0
SNMPv2-SMI::mib-2.90.1.1.3.0 = Gauge32: 0
SNMPv2-SMI::mib-2.90.1.1.4.0 = Gauge32: 0
SNMPv2-SMI::mib-2.90.1.1.5.0 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.3.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = STRING: "9"
SNMPv2-SMI::mib-2.90.1.2.1.1.3.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = STRING: "11"
SNMPv2-SMI::mib-2.90.1.2.1.1.3.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = STRING: "8"
SNMPv2-SMI::mib-2.90.1.2.1.1.3.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = STRING: "13"
SNMPv2-SMI::mib-2.90.1.2.1.1.3.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = STRING: "13"
SNMPv2-SMI::mib-2.90.1.2.1.1.3.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = STRING: "11"
SNMPv2-SMI::mib-2.90.1.2.1.1.4.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.2.1.1.4.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.2.1.1.4.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.2.1.1.4.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.2.1.1.4.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.2.1.1.4.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.2.1.1.5.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = ""
SNMPv2-SMI::mib-2.90.1.2.1.1.5.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = ""
SNMPv2-SMI::mib-2.90.1.2.1.1.5.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = ""
SNMPv2-SMI::mib-2.90.1.2.1.1.5.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = ""
SNMPv2-SMI::mib-2.90.1.2.1.1.5.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = ""
SNMPv2-SMI::mib-2.90.1.2.1.1.5.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = ""
SNMPv2-SMI::mib-2.90.1.2.1.1.6.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = INTEGER: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.6.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = INTEGER: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.6.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = INTEGER: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.6.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = INTEGER: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.6.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = INTEGER: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.6.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = INTEGER: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.7.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = OID: SNMPv2-SMI::zeroDotZero
SNMPv2-SMI::mib-2.90.1.2.1.1.7.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = OID: SNMPv2-SMI::zeroDotZero
SNMPv2-SMI::mib-2.90.1.2.1.1.7.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = OID: SNMPv2-SMI::zeroDotZero
SNMPv2-SMI::mib-2.90.1.2.1.1.7.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = OID: SNMPv2-SMI::zeroDotZero
SNMPv2-SMI::mib-2.90.1.2.1.1.7.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = OID: SNMPv2-SMI::zeroDotZero
SNMPv2-SMI::mib-2.90.1.2.1.1.7.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = OID: SNMPv2-SMI::zeroDotZero
SNMPv2-SMI::mib-2.90.1.2.1.1.8.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.8.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.8.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.8.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.8.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.8.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.9.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = INTEGER: 2
SNMPv2-SMI::mib-2.90.1.2.1.1.9.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = INTEGER: 2
SNMPv2-SMI::mib-2.90.1.2.1.1.9.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = INTEGER: 2
SNMPv2-SMI::mib-2.90.1.2.1.1.9.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = INTEGER: 2
SNMPv2-SMI::mib-2.90.1.2.1.1.9.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = INTEGER: 2
SNMPv2-SMI::mib-2.90.1.2.1.1.9.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = INTEGER: 2
C:\usr>
C:\usr>snmpwalk -v 2c -c m4nc4rc0 10.20.91.2 1.3.6.1.2.1.47.1.1.1.1.2
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1 = STRING: "Cisco Systems, Inc. WS-C4507R+E 7 sl
ot switch "
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.3 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.4 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.6 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.7 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.8 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.9 = STRING: " WS-C4507R+E 7 slot switch backplane
SNMPv2-SMI::mib-2.47.1.1.1.1.2.10 = STRING: "Container of Fan Tray"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.11 = STRING: "FanTray"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.12 = STRING: "Container of Container of Power Sup
ply"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.13 = STRING: "Container of Power Supply"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.14 = STRING: "Power Supply ( AC 2800W )"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.15 = STRING: "Power Supply Fan Sensor"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.16 = STRING: "Container of Power Supply"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.19 = STRING: "Clock Module"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.20 = STRING: "Mux Buffers for Redundancy Logic"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.21 = STRING: "Mux Buffers for Redundancy Logic"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.22 = STRING: "Mux Buffers for Redundancy Logic"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.23 = STRING: "Mux Buffers for Redundancy Logic"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.24 = STRING: "Mux Buffers for Redundancy Logic"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1000 = STRING: "10GE (X2), 1000BaseX (SFP) with 6
10GE X2 ports"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1001 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1002 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1003 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1004 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1005 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1006 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2000 = STRING: "1000BaseX (SFP) with 24 SFP Ports
Jumbo Frame Support"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2001 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2002 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2003 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2004 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2005 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2006 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2007 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2008 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2009 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2010 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2011 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2012 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2013 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2014 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2015 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2016 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2017 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2018 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2019 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2020 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2021 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2022 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2023 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2024 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2047 = STRING: "1000BaseSX"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2048 = STRING: "1000BaseSX"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.4000 = STRING: "Sup 7-E 10GE (SFP+), 1000BaseX (S
FP) with 4 SFP+ Ports"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.4001 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.4002 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.4003 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.4004 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5000 = STRING: "10/100/1000BaseT (RJ45)V with 48
10/100/1000 baseT voice power ports (Cisco/IEEE)"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5001 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5002 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5003 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5004 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5005 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5006 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5007 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5008 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5009 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5010 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5011 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5012 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5013 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5014 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5015 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5016 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5017 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5018 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5019 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5020 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5021 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5022 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5023 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5024 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5025 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5026 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5027 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5028 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5029 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5030 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5031 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5032 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5033 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5034 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5035 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5036 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5037 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5038 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5039 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5040 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5041 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5042 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5043 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5044 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5045 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5046 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5047 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5048 = STRING: "Gigabit Ethernet Port"
C:\usr> -
Auto Email on event - EEM script for NxOS
I generated EEM script for Duplicate IP address detection, but i do not know how to trigger email in NxOS.
event manager environment emailto "[email protected]"
event manager applet Duplicate_IP
description "Detect Duplicate IP and Send Trap"
event syslog pattern "%ARP-2-DUP_SRC_IP"
action 1.0 snmp-trap strdata "Duplicate IP Detected on Host $hostname"
action 2.0 cli sh logg last 100
action 3.0 event-default
Somebody know how to trigger email. There is no good document on EEM email triggering mechanism.Not sure if this would work in NxOS but I think it would go something like this;
Specify the action of sending a short e-mail when the EEM applet is triggered via the event syslog pattern you already have defined:
Router(config-applet)# action label mail server server-address to to-address from from-address subject subject body body-text
Remember to define the EEM environment variables first when setting up the applet as follows:
event manager environment _email_server
event manager environment _email_to
event manager environment _email_from -
EEM Script to use in an triple play network
Hi,
I have a customer which have a tripe play network. I attach the following drawing so you can have a better idea how the network looks like.
IPTV, Internet and IP telephony is getting in in our customer network at both PE some you can see in the drawing.
Basicaly our customer deliver the network infrastructure while ISP1, ISP2 and ISP3 deliver the content (IPTV, Internet and IP telephony).
The two PEs which are getting the content in the network from the 3 ISPs are running the following hardware and IOS:
cisco CISCO7606 with WS-SUP720 MSFC3 Daughterboard Rev. 3.2.
IOS version: c7600s72033-advipservicesk9-mz.122-33.SRC5.bin
BGP is used between the PEs and the ISPs router.
The PEs are redundant for each other.
Our issue is when one of the ISP is having some maintenance on their routers one the PEs goes really high on CPU until reaching 100%.
I don't know why that is happening that is why I want to use EEM to dig deeper into it.
So What I want to do is an EEM script that could do the following:
1) The script should be triggered when CPU Threshold is reached (lets say 85 %).
3) Run a show tech and save the output in flash.
2) Then the script should run do the following commando and save the outputs to flash:
- sh ip bgp vpnv4 vrf VRF10102 neighbors
- sh bgp vpnv4 unicast vrf VRF10102 summary
- sh ip bgp vpnv4 vrf VRF10102 neighbors x.x.x.x advertised-routes
- sh ip bgp vpnv4 vrf VRF10102 neighbors x.x.x.x received-routes
- sh isis neighbors detail
3) Run "sh log" and save the output into flash.
Anyone has an idea how I could made this script with EEM?
Thanks in advance for your help.
Best regards,
LaurentI don't think you need a script for this. An applet should work just fine. This kind of thing is commonly done by TAC to aid in data collection for transient problems. This policy should work provided the CPU instance is correct. A 7600 will have at least two CPUs. This applet assumes CPU instance 1 is the desired CPU, but it may be CPU instance 2 you need to monitor.
event manager applet watch-cpu event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.11.1 get-type exact entry-op ge entry-val 90 exit-op lt exit-val 90 poll-interval 60 maxrun 300 action 1.0 cli command "enable" action 1.1 cli command "term exec promp time" action 2.0 cli command "show tech | append disk0:/high_cpu.txt" action 3.0 cli command "sh ip bgp vpnv4 vrf VRF10102 neighbors | append disk0:/high_cpu.txt" action 4.0 cli command "sh bgp vpnv4 unicast vrf VRF10102 summary | append disk0:/high_cpu.txt" action 5.0 cli command "sh ip bgp vpnv4 vrf VRF10102 neighbors x.x.x.x advertised-routes | append disk0:/high_cpu.txt" action 6.0 cli command "sh ip bgp vpnv4 vrf VRF10102 neighbors x.x.x.x received-routes | append disk0:/high_cpu.txt" action 7.0 cli command "sh isis neighbors detail | append disk0:/high_cpu.txt" action 8.0 cli command "show logg | append disk0:/high_cpu.txt" -
Weblogic.admin script to alert server status
Hi,
Can anybody share a weblogic.admin utility script for alerting the server status in unix ?Below is the solaris shell script integrated with weblogic.admin utility....
If the server status is other than running it will sends a alert mail to you.
Sometime your server may be in shutdown mode and if you execute the below script, it says destination not reachable on specified port and then also it sends a alert mail.
Change it according to ur env and execute...
set -x
export CLASSPATH=”/wl_home/server/lib/weblogic.jar”
declare -a Port=( 8003 7072 8201 )
declare -a ServerState[]
declare -a ServerName[]
declare -a ObjectName[]
i=”0″
IP=Weblogic host address
while [ $i -lt 5 ]
do
ServerState[$i]=`java weblogic.Admin -url $IP:${Port[$i]} -username weblogic -password weblogic GET -pretty -type ServerRuntime -property State |grep -i State |awk ‘{print $2}’`
ObjectName[$i]=`java weblogic.Admin -url $IP:${Port[$i]} -username weblogic -password password GET -pretty -type JVMRuntime -property ObjectName |grep -i ObjectName |awk ‘{print $2}’`
if [ "${ServerState[$i]}” != “RUNNING” ] ;
then
mailx -s ” Weblogic Server Staus- $IP ” [email protected]<<EOF
Weblogic Managed server ${Port[$i]} is in SHUTDOWN state
EOF
fi
i=`expr $i + 1`
done
Thanks,
Kartheek
Troubleshooting in weblogic gives thrilling experience ....... -
How to configure CCMS alert to monitor Authorization failures?
Dear All,
How to configure CCMS alert to monitor Authorization failures?
Thanks
AshokHello,
in case you have not yet set up your monitoring infrastructure, the following link will provide you with the information needed:
http://service.sap.com/monitoring
If everything is set up (Agents are installed and connected to your central monitoring system, ...) you can go to transaction RZ21, select Technical Infrastructure - Configure Central System - Assign Central Autoreactions to set up your alerts.
For the Update errors use the MTE CLass AbapErrorInUpdate. For the Lock please use the search Option.
Regards
Christian
Edited by: Christian Rose on Apr 25, 2011 7:59 PM -
I had plans to configure a EEM script to send a email when an OSPF adjacency drops. I have an odd spanning-tree issue that I believe the drops are related to and I want to see if my suspicions are correct. This doesn't happen very often, and it's normaly late at night.
I originally planned something like this:
event manager environment _email_server 192.168.x.x
event manager environment _email_to [email protected]
event manager environment _email_from [email protected]
event manager session cli username "user"
event manager applet OSPF
event syslog pattern "%OSPF-"
action 1.0 cli command "enable"
action 1.1 cli command "show spanning-tree vlan 192"
action 1.2 cli command "show spanning-tree vlan 192 detail"
action 1.3 wait 10
action 1.4 cli command "show spanning-tree vlan 192"
action 1.5 cli command "show spanning-tree vlan 192 detail"
action 1.6 wait 20
action 1.7 cli command "show spanning-tree vlan 192"
action 1.8 cli command "show spanning-tree vlan 192 detail"
action 1.9 mail server "$_email_server" to "$_email_to" from "$_email_from" subject "Spanning-tree results" body "$_cli_result"
After trying this, it doesn't seem that NXOS support the email function.
My questions:
1. What alternative do I have? Is there a way to send the CLI output via SNMP or syslog?
2. Will this even run EVERY time the syslog pattern matches? Meaning if I get four %OSPF syslog messages, it will run four times repeatedly? \
Thank you,Hello Arie,
Thank you for answering my questions.
This is what I've got now. I think it will work well.
event manager applet OSPF
event syslog pattern "%OSPF-4-NEIGH_ERR"
action 1.0 cli command "enable"
action 1.1 cli command "show clock >> bootflash:ospf"
action 1.2 cli command "show spanning-tree vlan 192 >> bootflash:ospf"
action 1.3 cli command "show spanning-tree vlan 192 detail >> bootflash:ospf"
action 1.4 wait 10
action 1.5 cli command "show clock >> bootflash:ospf"
action 1.6 cli command "show spanning-tree vlan 192 >> bootflash:ospf"
action 1.7 cli command "show spanning-tree vlan 192 detail >> bootflash:ospf"
action 1.8 wait 10
action 1.9 cli command "show clock >> bootflash:ospf"
action 2.0 cli command "show spanning-tree vlan 192 >> bootflash:ospf"
action 2.1 cli command "show spanning-tree vlan 192 detail >> bootflash:ospf"
action 2.2 cli command "end"
action 2.3 cli command "exit"
--- Turns out "wait" isn't a option in NXOS either. I just put "show logging info" in its place, and didn't append it to the output file. That command takes about 10-15 seconds to run for some reason, so it should give me the pause I want. -
Basic traceroute EEM script (for hop-by-hop network analysis)
I'd like to do a hop-by-hop analysis by running a traceroute script that runs on an interval (say every 5-15 minutes) and puts output to a file.
The goal is to let the script run for a day, and see what kind of hop changes might occur over time, and also monitor for any latency increase or packetloss at certain times of day (peak hours).
If I used an EEM script to do a basic traceroute from one endpoint of the network to a server in the core (for instance), this could show how a client's path may be impacted during peak hours.
I'd want the output stored in a file on the router's flash disk, and then I'd have to find some way to parse and analyze the output later (not sure how I'd do that, perhaps with excel or another diff-like program).Something like this should work for you. In config mode, specify three EEM environment variables:
event manager environment traceroute_timer 600
event manager environment traceroute_target 10.1.1.1
event manager environment traceroute_file flash:/traceroute.txt
Then register this EEM Tcl policy:
::cisco::eem::event_register_timer watchdog time $traceroute_timer
namespace import ::cisco::eem::*
namespace import ::cisco::lib::*
array set arr_einfo [event_reqinfo]
if [catch {cli_open} result] {
error $result $errorInfo
} else {
array set cli1 $result
if [catch {cli_exec $cli1(fd) "enable"} _cli_result] {
error $_cli_result $errorInfo
if [catch {cli_exec $cli1(fd) "traceroute $traceroute_target"} _cli_result] {
error $_cli_result $errorInfo
set fd [open $traceroute_file a]
puts $fd [clock format [clock seconds]]
puts $fd $_cli_result
close $fd
# Close open cli before exit.
catch {cli_close $cli1(fd) $cli1(tty_id)} result -
Cisco 1841/871 crash EEM scripting 15.1(1)T
We have been testing 15.1.1T on a couple of lab Cisco 1841 and Cisco 871 devices.
On the devices we are using EEM to automate the failover/failback process for a cellular modem attached to f3 on the 871 or f0/1 on the 1841. One of the EEM applets we use fires from a cron timer event that occurs every 10 minutes on the router.
IOS revision 12.4(22)T we had no problems with using the cron-timer triggered applet (every 10 minutes between 7am to 10pm), except for the fact that every command issued by EEM required AAA authentication. The EEM applet is causing our routers to saturate our Cisco ACS servers (we use 700+ routers in the field, all exectuing this EEM script) with single-connect requests. We will refer to the cron-timer executed applet as 'Maintenance' from here on out.
As of 15.1(1)T the addition to bypass the AAA authentication process became available. This was a huge speed increase to our EEM applets, specifically the Maintenance applet. I will include the applet for clairity.
event manager applet Maintenance authorization bypass
event timer cron name 10min cron-entry "*/10 7-21 * * *" maxrun 30
action 001 cli command "en"
action 002 cli command "show ip route | section B\*[ ]+0\.0\.0\.0"
action 003 regexp "^B\*.([ ]+)(0\.)+0" "$_cli_result"
action 004 set bgpstate "$_regexp_result"
action 005 cli command "show ip route | section S[ ]+208\.38\.154\.8"
action 006 regexp "^S([ ]+)208\.38\.154\.8" "$_cli_result"
action 007 set wireless "$_regexp_result"
action 008 track read 1
action 009 set track1 "$_track_state"
action 010 if $wireless eq 0
action 011 if $bgpstate eq 0
action 012 cli command "conf t"
action 013 cli command "int fa0/1"
action 014 cli command "no shut"
action 015 cli command "int tun201"
action 016 cli command "no shut"
action 017 cli command "int lo201"
action 018 cli command "no shut"
action 019 if $track1 eq up
action 020 exit
action 021 else
action 022 cli command "conf t"
action 023 cli command "int s0/0/0"
action 024 cli command "no shut"
action 025 end
action 026 cli command "end"
action 027 cli command "exit"
action 028 else
action 029 exit
action 030 end
action 031 else
action 032 if $bgpstate eq 1
action 033 cli command "conf t"
action 034 cli command "int fa0/1"
action 035 cli command "shut"
action 036 cli command "int tun201"
action 037 cli command "shut"
action 038 cli command "int lo201"
action 039 cli command "shut"
action 040 cli command "end"
action 041 cli command "exit"
action 042 else
action 043 if $track1 eq up
action 044 exit
action 045 else
action 046 cli command "conf t"
action 047 cli command "int s0/0/0"
action 048 cli command "no shut"
action 049 end
action 050 cli command "end"
action 051 cli command "exit"
action 052 exit
action 053 end
action 054 end
This script is designed to look for a couple of routes in the IP routing table, and populate two variables (bgpstate and wireless) with the regular expression matching result of the show ip route commands. It uses track 1 to determine the up/down status of Serial0/0/0 which is the primary T1 interface for WAN services on the router. The wireless is "up/1" if the static route to 208.38.154.8 is present in the show ip route output (only when f0/1 is up in this case). The T1 is "up/1" if the default route passed to the IP routing table is present in the show ip route output.
Before the upgrade to 15.1(1)T these scripts ran without issue, and we had no errors. Now after the upgrade, anytime this script fires and the show ip route match for the wireless variable is 1 instead of zero, it begins to run through the else condition starting at action 031, and during the second execution of the script every 10 minutes (I still have not figured out how to force the cron-timer to fire only ONCE per minute, instead of at the beginning and end of the minute), the router will generate spurious memory errors, and sometimes crash or reboot.
This all began with 15.1(1)T, and I have not seen any caveats or other entries that could possibly point to the cause of this problem. Any ideas?
I am also attaching a crash file from one of the routers like this one so you can see what I mean.
All of these devices are running the advipservices k9 version of this IOS.
Thanks for your time.The problem with cron events running twice in the same minute is bug CSCsz12460 which will be fixed in EEM 3.2 in 15.1(3)T.
The crash you're seeing doesn't appear to be related to EEM at all. It looks like a problem with single-connection TACACS+. The bug appears to be CSCtg40901 which has not yet been fixed in 15.1T.
A workaround was suggested to use multiple-connection TACACS+. -
Can we set an Alert for JDBC Connection Failures ?
Hi friends ,
Can we set an alert for JDBC Connection failure as mail as well as Alert ?
I am using JDBC Sender adapter to read the data from sql server table.
I am not using BPM .
I want to set an alert and mail to respective person when JDBC Connection failure .
If XI trying to read a database if connection failure or connection properties lost it won't come ti Integration engine itself right ?
I assume as we have to set alert at system level .
Can you please give me the step by step details to set this kind of alerts ?
Expecting your reply asap .
Best Regards.,
V.RangarajanRenga rajan,
This is what I tried to explain in yuor previous threads.
>>>If XI trying to read a database if connection failure or connection properties lost it won't come ti Integration engine itself right ?
In such cases, you will get <b>an error at adapter level</b> and the msg wont come into IE.
>>>I assume as we have to set alert at system level .
If you are above SP 14 in XI3.0, then you can raise alerts for adapter errors also.
No special config required for this.
To understand this, give it a try and you will get the concept.
Regards,
Jai Shankar -
EEM script not running in WS-C4900M switch
Hello,
I am having two WS-C4900M switches which were giving high cpu spikes hence we have configured EEM script in it to capture switch behaviour during cpu spikes.when CPU goes high script do get hit but the commands under script doesn't run and we are not able fecth command outputs during high cpu.
Pleas find script uploaded and show version of switch attached.I don't think you need a script for this. An applet should work just fine. This kind of thing is commonly done by TAC to aid in data collection for transient problems. This policy should work provided the CPU instance is correct. A 7600 will have at least two CPUs. This applet assumes CPU instance 1 is the desired CPU, but it may be CPU instance 2 you need to monitor.
event manager applet watch-cpu event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.11.1 get-type exact entry-op ge entry-val 90 exit-op lt exit-val 90 poll-interval 60 maxrun 300 action 1.0 cli command "enable" action 1.1 cli command "term exec promp time" action 2.0 cli command "show tech | append disk0:/high_cpu.txt" action 3.0 cli command "sh ip bgp vpnv4 vrf VRF10102 neighbors | append disk0:/high_cpu.txt" action 4.0 cli command "sh bgp vpnv4 unicast vrf VRF10102 summary | append disk0:/high_cpu.txt" action 5.0 cli command "sh ip bgp vpnv4 vrf VRF10102 neighbors x.x.x.x advertised-routes | append disk0:/high_cpu.txt" action 6.0 cli command "sh ip bgp vpnv4 vrf VRF10102 neighbors x.x.x.x received-routes | append disk0:/high_cpu.txt" action 7.0 cli command "sh isis neighbors detail | append disk0:/high_cpu.txt" action 8.0 cli command "show logg | append disk0:/high_cpu.txt"
Maybe you are looking for
-
College student coupons not received after 3 days of waiting
I signed up in store on Sunday, 10/5/2014 to receive college student coupons. They have yet to arrive. I got the message to confirm my address, which I did. I have also since gotten some email spam from Best Buy, so I know that those messages aren't
-
Ok, I'm pretty saavy when it comes to most things computer related but maybe I'm missing something on this one. I bought my Intel mini with the stock 512mb of RAM and decided I wanted to upgrade to 2gb. The price of RAM is fairly steep right now so I
-
During cancelation of MIRO document giving error message "RG23 Part II post
Dear guru's, I am facing a tipical issue while i am going to reverse the MIRO document it is giving error "RG23 Part II posting not yet done" . Senario is -- user has created MIGO with Myp103 and then 105, system promted excise tab and excise ref.
-
IBook G4 has to be tilted 90º backwards to boot - is it HDD or Logic Board?
I have a client's G4 iBook 12" 1GHz - that has to be tilted a full 90º for it to start-up/boot ... The machine hangs on the grey start-up screen when positioned on a desk normally and won't boot - it chimes, display the grey screen - but i f I turn a
-
Hi in our case fiscal year is calender year JAn to Dec. However for the legal point of view we have to close our books also for FY April to March every year In asset accouting asset history sheet show the values starting from January (as per fiscal y