Error in SM58 on r/3 side in idoc to jdbc scenario

Hi Experts,
I am sending the idoc from R3 to XI, in r3 side idoc successfully created and status is 03, but when check in sm58 it is complaining about user name and password.
but the problem in rfc destination to xi system, when i click on remote logon it is asking for the username and password, is it asking like that or not.
i created partner profiles, and port and idx2 also.
Can you help me out of this.
Kind Regards,
Praveen.

Hello Praveen,
I suggest the below things
1. First check user password and client are all provided correctly
2. If still problem persists then the problem may be due to used R/3 version if it is lower than or quals to 4.6
then it tries to convert the password to capital letters and tries to login as a result the failure
in this case need to change the password to capital letters and should not be more than 8 chars
check note 792850.
Rajesh

Similar Messages

Very strange error : IDOC to jdbc scenario

Hi
I am getting a very strange error when I see the log for the idoc to jdbc scenario that I am building.
The mapping test shows the header record and line item record properly in the mapping result.
insert, access nodes, fields with access nodes are all formed correctly.
However the communication channel log shows below error.
Could not execute statement for table/stored proc. "tblTestItem" (structure "Item") due to com.microsoft.sqlserver.jdbc.SQLServerException: Incorrect syntax near ')'.
JDBC Message processing failed, due to Error processing request in sax parser: Error when executing statement for table/stored proc. 'tblTestItem' (structure 'Item'): com.microsoft.sqlserver.jdbc.SQLServerException: Incorrect syntax near ')'.
The message status was set to WAIT.
The query that I see in the log is :INSERT INTO tblTestItem () VALUES ()
However mapping tool shows that all nodes are correctly formed.
Please assist.

Hi
I am still getting this issue even after the below steps so kind of stuck - actually very much stuck.
1. Restart of the dev environment
2. Tried with a new extension of the idoc
In the communication channel log for the JDBC receiver channel I still see
INSERT INTO tblItem () VALUES ()
The payload that I see in the message content tab is as follows
<?xml version="1.0" encoding="UTF-8" ?>
- <ns0:MT_XXX_XXXX xmlns:ns0="http://capita.com/pi/XXXX">
- <Statement>
- <dbTableName action="INSERT">
<table>tblItem</table>
</dbTableName>
- <access>
<InvoiceNo>0000000009293467</InvoiceNo>
</access>
</Statement>
</ns0:MT_XXX_XXXX>
How do I debug the jdbc adapter to see how it converts the above xml output from the mapping step (note that this output is from an actual run and not test tool) to a sql query.
Very strange that the column names are present in the target payload but it is not reflecting in the query.
I have other tables being populated with the same jdbc receiver communication channel which makes this more and more confusing.
PLEASE ADVICE.

Error in IDoc to JDBC scenario

Hi friends,
I am configuring an IDoc to JDBC scenario in XI.When I am testing the scenario in Test Configuration then it is getting processed successfully but when I am tseting the entire configuration then in sxmb_moni the following error is showing:
"Error occurred during back-routing Error in communication channel". Please help as I am unable to understand the error.
regards
Debansu

Hi Debansu,
Please go through the link it may help to solve your problem.
JDBC Adapter / Acknowledgements
Error in back routing Error in communication channel
Regards,
Sridhar Goli
Edited by: sridhar goli on Aug 11, 2008 11:35 AM

IDOC to JDBC Scenario error

Hi All,
I am doing a IDOC to JDBC Scenario.I am done with IR and ID.
The Table in the DB is TABLE1 with Field1 and Field2.
Now when I run thescenario it throws an error ,
2009-03-19 12:41:06 Success INSERT INTO TABLE1 (Field1, Field2) VALUES (KM247850, FINJTIA)
2009-03-19 12:41:06 Error Unable to execute statement for table or stored procedure. 'TABLE1' (Structure 'Statement') due to java.sql.SQLException: [EUDNT038]The name "KM247850" is not permitted in this context. Valid expressions are constants, constant expressions, and (in some contexts) variables. Column names are not permitted.
But it has successfully generated the SQL Query which I think is perfect.
But whats the error which follows that?
How do I resolve it?
Thanks,
Venu

Hi,
It could be due to wrong structure of JDBC, compare your target structure with this blog..
/people/sap.user72/blog/2005/06/01/file-to-jdbc-adapter-using-sap-xi-30
Regards,
Sarvesh

FCC in receiver side in idoc to file scenario

Hi all,
           I am doing an idoc to file scenario using FCC .I am using FCC in receiver side ,but i am getting my output file in only one line while i want structre to be seprated by new line.for more information i am giving muy file structre.
Record
    header(1to1)
    data    (0 to unbounded)
    footer (1to 1)          header, data, footer are three structre which contain various fields.I have to use fieldFixedLengths as filed separator. I am also using endseperator as 'nl' but its not coming in new line.Please share ur views on this issue.
Regards
Neha

hi neha,
In your scenario
Recordset Structure header,data,footer
header.fieldFixedLengths    = 1,2,3, whatever it is
data.fieldFixedLengths      = similar to header
footer.fieldFixedLengths    = similar to header
header.endSeparator = 'nl'
data.endSeparator = 'nl'
footer.endSeparator = 'nl'
I guess you dont have to do any thing else.
Regards
Pushkar
Message was edited by:
        Pushkar Anand

Error Resource not Found in SXMB_MONI while doing IDoc to File Scenario

Hi Experts,
I am doing IDoc to File Scenario and I am facing Following Error in SXMB_MONI,
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- 
- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="">
<SAP:Category>Application</SAP:Category>
<SAP:Code area="MAPPING">RESOURCE_NOT_FOUND</SAP:Code>
<SAP:P1>193c0e01-bd37-11dd-850c-d879ac131b1f</SAP:P1>
<SAP:P2>http://clarityPOC</SAP:P2>
<SAP:P3>com/sap/xi/tf/_MM_Timesheets_iDocToFile_.class</SAP:P3>
<SAP:P4>-1</SAP:P4>
<SAP:AdditionalText />
<SAP:Stack>Unable to find resource 193c0e01-bd37-11dd-850c-d879ac131b1f in the following software component versions: http://clarityPOCcom/sap/xi/tf/_MM_Timesheets_iDocToFile_.class-1</SAP:Stack>
<SAP:Retry>M</SAP:Retry>
</SAP:Error>
I have tested the same file in test tab of mapping, execution of mapping is successful there.
Regards,
Nitin Patil
Edited by: Nitin Patil on Dec 5, 2008 7:09 AM

Hi Dharmveer I have done the cache refresh ID in XI Data Cache Refresh using link
http://sapnbipoc:50000/rep/support/admin/index.html
but still same error persisting
and in Integration Builder> Environment>Cache Status Overview >Problem tab
following error (initial part of the error pasted) is shown
Thrown:
com.sap.aii.ib.bom.landscape.SLDElementNotFoundException: Adapter Engine af.npi.sapnbipoc not found in SLD
     at com.sap.aii.ib.server.abapcache.sld.AdapterEngineQueries.getAEUrl(AdapterEngineQueries.java:56)
     at com.sap.aii.ib.server.abapcache.sld.AdapterEngineQueries.getAEUrl(AdapterEngineQueries.java:41)
     at com.sap.aii.ib.server.abapcache.logons.IR_LogonData.<init>(IR_LogonData.java:26)
Regards,
Nitin Patil

IDOC---JDBC scenario error: "INTERNAL" HTTP_RESP_STATUS_CODE_NOT_OK

i have a IDOC-XI--JDBC scenario,
the scenario fails at the Call Adpater Pipeline step............giving following error:
<SAP:Category>XIServer</SAP:Category>
<SAP:Code area="INTERNAL">HTTP_RESP_STATUS_CODE_NOT_OK</SAP:Code>
<SAP:P1>401</SAP:P1>
<SAP:P2>Unauthorized</SAP:P2>
<SAP:Stack>HTTP response contains status code 401 with the description Unauthorized Authorization error when sending using HTTP (error code: 401, error text: Unauthorized)</SAP:Stack>
pls help me.....
Message was edited by:
sudeep dhar

but this error occurs after few message pass successfully.....
means at an interval this error happens...then again few messgae pass successfully,
This is the error which i get in MONI:
ERROR_CATEGORY: INTERNAL
ERROR_ID: HTTP_RESP_STATUS_CODE_NOT_OK
and in the pipeline step i can see the error:
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- 
- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="">
<SAP:Category>XIServer</SAP:Category>
<SAP:Code area="INTERNAL">HTTP_RESP_STATUS_CODE_NOT_OK</SAP:Code>
<SAP:P1>401</SAP:P1>
<SAP:P2>Unauthorized</SAP:P2>
<SAP:P3 />
<SAP:P4 />
</SAP:AdditionalText>
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack>HTTP response contains status code 401 with the description Unauthorized Authorization error when sending using HTTP (error code: 401, error text: Unauthorized)</SAP:Stack>
<SAP:Retry>M</SAP:Retry>
</SAP:Error>

IDOC to JDBC :Error using JDBC

Hi Frnds,
My scenario is Idoc to JDBC scenario, I am getting the follwoing error while trying to process an idoc. Please help me in hadling this error.
Error Message:
JDBC message processing failed; reason Error when attempting to get processing resources: com.sap.aii.af.service.util.concurrent.ResourcePoolException: Unable to create new pooled resource: DriverManagerException: Cannot establish connection to URL 'jdbc:microsoft:sqlserver://180.1.32.194:1433;DatabaseName=CZZ03;': SQLException: [Microsoft][SQLServer 2000 Driver for JDBC]Error establishing socket.
Regards,
Shiv

Hello Shiva,
Are you installed JDBC Drivers?
Go through this links,
/people/varadharajan.krishnasamy/blog/2007/02/27/configuring-jdbc-connector-service-to-perform-database-lookups
http://searchsap.techtarget.com/tip/0,289483,sid21_gci1246926,00.html
To install JDBC driver follow the how to guide.
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/library/xi/xi-how-to-guides/how%20to%20install%20and%20configure%20external%20drivers%20for%20jdbc%20and%20jms%20adapters.pdf
Configuration of JDBC Adapter for SQL Server
JDBC Driver = com.microsoft.jdbc.sqlserver.SQLServerDriver
Connection = jdbc:microsoft:sqlserver://hostname:<port>;DatabaseName=<DBName>
UserID and Password.
If the connection is not working find the correct port number.
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/40b92770-db81-2a10-8e91-f747188d8033
JDBC- X I - R/3 Scenario
/people/bhavesh.kantilal/blog/2006/07/03/jdbc-receiver-adapter--synchronous-select-150-step-by-step
/people/sap.user72/blog/2005/06/01/file-to-jdbc-adapter-using-sap-xi-30
Please check the driver path as mentioned below.
JDBC Driver : sun.jdbc.odbc.JdbcOdbcDriver
Connection:jdbc:odbc:Driver={Microsoft Access Driver (*.mdb)};DBQ=//location of DB table.mdb;
No JDBC driver required.
Receiver JDBC scenario MS access - /people/sameer.shadab/blog/2005/10/24/connecting-to-ms-access-using-receiver-jdbc-adapter-without-dsn
follow this thread
Re: Problem when connecting to MS Access through JDBC Adapter.
SAP Note 850116 has details
Thanks,
Satya Kumar
Reward if it is usefulll

IDoc_AAE Synchronous error in SM58

Dear friends,
I configured IDoc_AAE sender and receiver side. I tested this with success. The next step was to configure an Async-Sync scenario. I configured my scenario according the following Blog:
Request/Response Bean for IDOC_AAE adapter
My scenario is that I want to take an IDOC from ECC and send it to SOAP which is synchronous one and I map the response data to a ALEAUD and send it back to ECC.
My configuration looks like following:
I use the following Beans and parameters in the sender Idoc communication channel:
Now when I want to send an Idoc from ECC I get the following error in SM58:
Commit fault: ASJ.ejb.005043 (Failed in component: sap.com/com.sap.aii.ad
And I get the following error in NWA:
Error in look up for binding. Reason: com.sap.aii.af.service.cpa.CPAObjectNotFoundException: Couldn't retrieve inbound binding for the given P/S/A values: FP=;TP=;FS=BS_******;TS=;AN=IDOC Name;ANS=urn:sap-com:document:sap:idoc:messages;
So If I test this idoc asynchronous it works fine and if I put this Idoc in an Outbound Sync SI it doesn't work and I get an error in SM58.
Do you have any suggestion why it doesn't work and can you please tell me If I can achieve my scenario with this configuration? As I read in the following thread (it was mentioned by Indrajit that we cannot use an Idoc adapter in the ResponseOneWayBean)
ResponseOneWay Bean unable to find the receiver channel
If its true so what do I can do to achieve this scenario? I also can use an asynchronous ABAP Proxy back to ECC instead of an ALEAUD.
You help would greatly appreciated,
Thank you in advanced,
Kind regards,
John

Hi
Unfortunately the way you are trying to get the acknowledgement idoc will not work.The request response bean in the sender idoc adapter only work for
Adapter Namespace: http://sap.com/xi/XI/System.
Adapter Type: File
The same is clearly mentioned in the document you have referred. But there is another alternative approach which you can use to get the acknowledgment back.
You have to use the request response bean in the receiver adapter( say SOAP). In that case the receiver application will trigger an response message with the interface name you have provided in the response bean.
You have to create one more ICO or scenario for that interface triggered by receiver adapter and use the mapping in PI which will convert that in ALEAUD idoc.
Following things needs to keep in mind
You have to use virtual receiver for the second scenario.

XI: idoc 2 file scenario( Contain error in SM58)

Hi experts,
Here i am having one issue. i have done Idoc 2 file scenario...i have created material in R/3 successfully. when i have sent the material to legacy system..Idoc was generated Successfully in r/3 but i haven't seen that message in SXMB_MONI..
i got the error message in SM58 i.e. IDX1 port SAPDE1, Client 220, RFc Destination Contain error.
plz any one can u help me on this....
Regards,
Yadav

Hi Yadav,
The RFC port you defined is not correct in IDX1. The Port name must be in the form of u201CSAPxxxu201D, where xxx is the system ID of the backend SAP system.
Just cross check it.
Check this for more details:
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/library/uuid/d19fe210-0d01-0010-4094-a6fba344e098
Regards,
Sachin

RFC destination error in SM58

Hi,
We are getting an error in SM58 "P85040 does not exist".
What could be the reason for this error in PI system?
When I checked, there is no RFC destination configured with the name P85040. Also there is no communication channel configured with the RFC destination parameter P85040.
Kindlly help.
Thanks,
John

Hi John,
The reason can be the host name you are assigning is not existing.
In RFC destination the host name is for that particular client which is pointing to IP address not to the logical system. You can choose name of RFC destination same as of your logical system.
You can get the host name by login to SAP system and the using MENU ... System->Status and in lower right corner you can find it.
Sachin
Edited by: Sachin Dhingra on Dec 18, 2008 1:18 PM

Rfc to file scenario error in sm58

rfc to file scenario error in sm58
i get the error as com.sap.aii.afccommunication.RfcAfwException
:look up of alternative

hey
>>i have a doubt do we have to use
starting new task or back ground destination
well it depends upon the logic ur gonna implement,both are used for async RFC so u have to see ur requirement and then decide.
have a look at the following
http://help.sap.com/saphelp_nw2004s/helpdata/en/22/042578488911d189490000e829fbbd/frameset.htm
thanx
ahmad

IDOC Error in SM58 and Management Console

Hi Guys,
Good day!
I am currently having issues on sending IDOCs to BODS.
There are instances that an IDOC gets stuck or ends up with an error in transaction code SM58. In transaction WE02, the IDOC is
successfully processed with status 03. In a set of IDOCs (10 or more), one IDOC is in error in SM58, usually the first IDOC gets the error and the next IDOCs are successfully processed. The error received in SM58 displays the following:
Error 1: R3RfcClient(DI_CLIENT)ActaIDocFunc::Process()...
Error 2: CPIC-CALL ThSAPCMRCV no data received
However, the client interface is active/running.
In the management console, the error Logs-History displays the following:
(14.0) 04-08-14 23:32:51 (E) (8060:3868) Unknown: SP(INVOICE_001, ABC:1234)::flowThread() Flow became
invalid during waiting for request (BODI-300137)
(14.0) 04-08-14 23:32:51 (E) (8060:9356) Unknown: R3RfcClient(RFC_CLIENT_INTERFACE) ActaIDocFunc::Process()
encountered processing error for Requeste(15149) (Communication Error. See real time job log for details.) (IDOC 0000001234567890/ABCDE). (BODI-300129)
For the Real-Time Services log, the following is displayed:
(14.0) 04-08-14 23:32:39 (E) (70684:47620) RUN-051005: |Session REALTIME_INVOICE|Data flow DATAFLOW_INVOICE|Loader query_IDOC_DETAILS Execution of <Regular Load Operations> for target <IDOC_DETAILS> failed. Possible causes: (1) Error in the SQL syntax; (2) Database connection is broken; (3) Database related errors such as transaction log is full, etc.; (4) The user defined in the datastore has insufficient privileges to execute the SQL. If the error is for preload or postload operation, or if it is for regular load operation and load triggers are defined, check the SQL. Otherwise, for (3) and (4), contact your local DBA.
(14.0) 04-08-14 23:32:50 (E) (70684:68856) DBS-070401: |Session REALTIME_INVOICE|Data flow DATAFLOW_INVOICE|Loader query_IDOC_DETAILS ODBC data source <ABC\ABC,12345> error message for operation <SQLExecute>: <[Microsoft][SQL Server Native Client 10.0]TCP Provider: An existing connection was forcibly closed by the remote host. >.|<Regular Load Operations>|<IDOC_DETAILS>
Given this, I would like to ask on how to eliminate this issue.
Thanks,

Error in SM58 on XI box

Hi,
While trying to post IDocs to an R3 system, getting the following error in sm58 - 'Transactional RFC' transaction 'PASSWORD LOGON NO LONGER POSSIBLE'.
But when I do a connection test from SM59, to the corresponding RFC destination listed in the receiver IDoc adapter there is no issue. The test is successfull.
Anything I'am missing here?
Thanks,
Anand

>>>> did try a remote logon from the RFC destination...on doing this I get a dialog box requesting username/password entry. And the user that appears here is my user ID, not the user that is in the RFC destination.Is this standard behaviour?
No. This means your RFC destination is not working properly. Just fill the user Id, pwd with a valid user Id that has sufficient auth., then try. You should be directly logging into SAP on using the Remote logon option.
Regards,
Jai Shankar

Error in sm58

Hi all,
I am trying to send a IDOC from SAP system to XI and I getting the following error in sm58
Transaction IDX1: Port SAPEN5, Client 800, RFC Destination contian error.
BTW what is the difference between maintaing the port in we21 or idx1?

>>what is the difference between maintaing the port in we21 or idx1?
WE21 is mainted in R3.
IDX1 is maintained in XI.
<a href="/people/swaroopa.vishwanath/blog/2007/01/22/ale-configuration-for-pushing-idocs-from-sap-to-xi Configuration for Pushing IDOC's from SAP to XI</a> By Swaroopa Vishwanath
Regards
San
<a href="Remember to set the thread to solved when you have received a solution to set the thread to solved when you have received a solution</a>
Where There is a <a href="https://www.sdn.sap.comhttp://www.sdn.sap.comhttp://www.sdn.sap.com/irj/sdn/weblogs?blog=/weblogs/topic/16">blog</a> there is a Way.

Error in SM58 on r/3 side in idoc to jdbc scenario

Similar Messages

Maybe you are looking for