FF Id from Target system, does not appear to be assigned

Hi All,
I have configured ECC as a Connector, and a FF id with below roles, in ECC. After Repository Sync, the table GRACUSER, shows FF id from ECC. However, while assinging Owner to FF id, the FF id from ECC, is not shown.
SAP_GRAC_SPM_FFID
SAP_GRC_FN_BASE
SAP_GRC_FN_BUSINESS_USER
Any clue, what needs to be done here

HI Plaban
What is your configuration parameter 4010 role? Is that role assigned to the FF Id (before you ran the sync)?
Did you set the owner up as an Access Control Owner first?
Have you checked to ensure you have sufficient authorization GRC to assign the FF Id?
Regards
Colleen

Similar Messages

  • Mail sent from android phone does not appear in my pc icloud sent mail

    Can anyone educate me on why my mac mail sent from my android does not appear in
    my pc icloud mail as sent?

    What is the server address that the Android account is using?

  • I've changed my account's country, adress, and phone number because I've moved and my purchased apps (from previous country) does not appear anymore, how do I fix it?

    I've changed my account's country, address, and phone number because I've moved and my purchased apps (from previous country) does not appear anymore, how do I fix it?

    That is the expected behavior. You will also no longer be alerted to any updates for that content.
    If any of the content is sold in the new country's store and you find out through the grapevine about an update, you can update the content for free, but you will have to go through the steps for buying the update as a new purchase. Then the store will notice in the final steps that you own this content and update for free. It is the end of the road for any content from the previous country that is not sold in the current country's store. You will not be able to update the content in the new store.

  • PXI System does not appear in MAX 4.0

    Hello,
    My system comprises LabVIEW RT 7.0, target PXI-8176 controller in PXI-1000B chassis, PXI-6608, PXI-6711, NI-4472, PXI-6704, PXI-6527, PXI-8423/4, PXI-8422/4.  This has been stable for two years. I recently solved an RS-485 2-wire mode configuration problem, using information in a discussion forum thread, by upgrading to NI-VISA 3.4.1 and NI-Serial 2.5.5.  MAX 4.0 was installed as part of this process.  Everything seemed to work fine.  I instructed a distant customer to do the same, but they experienced some difficulty. To ensure we were working from the same starting point, I re-initialized my PXI system, using PXI Format Hard Drive Disk, version 7.0, from MAX 4.0.  I configured TCP IP address, and re-installed the RT software on the PXI controller.
    Next, I attempted to configure the PXI controller and chassis, in MAX, to update the pxisys.ini file, but the PXI System (Unidentified) does not appear under Remote System>>IP address>>Devices and Interfaces.  Similarly for the serial ports.  This worked before, but I cannot get this back.  What is wrong?
    Best regards,
    RonC

    Hello S. Bassett
    The controller is definitely booting in RT mode -- I can still run my applications on the RT target.  VISA seems configured properly also, I can make VISA calls without error in the application.
    In fact, the RT system seems to work correctly, and I contemplated leaving it as it is. However, the fact that MAX does not recognize the PXI system makes me nervous, and I cannot do some of the things I may want to do, for example independently configure RS-485 port wire mode in MAX (the ports do not show up either).  Traditional DAQ configuration in MAX works.
    After your last post, I found a brief reference in MAX Help that indicated "PXI Services" had to be downloaded before the chassis could be configured.  But there are no other mentions of what PXI Services is, what it does, or how to install them. PXI Services does not show up as RT Software in MAX. In the Windows Add/Remove Programs control panel in Windows, in the National Instruments software section, there are two apparently related entries:
    - NI PXI Platform Services for LabVIEW Real-Time 1.5.1
    - NI PXI Platform Services for Windows 1.5.1
    But, I cannot get these to install on the RT target.  Not knowing what was causing the problem, I uninstalled everything from  National Instruments, deleted all folders, and reformatted the PXI platform.  There was one problem during this process -- after uninstalling NI-Serial 2.5.5, it does not get removed from the Add/Remove programs control panel.  There is still a registry key that the uninstaller did not remove -- presumably this is the problem.
    I have rebuilt everything, but could not get NI-Serial to install -- the installer thinks there is a newer installed on the RT target (there isn't) and refuses to install NI-Serial 2.5.5.  So right now, I cannot install NI-SERIAL (any version), or remove the 'existing' NI_SERIAL, because it isn't actually there, and there is no uninstaller.
    Otherwise, everything seems to be back to where it was before I "upgraded" to NI-VISA 3.4.1.  This was NI-VISA 3.0, LV RT 7.0, and MAX 3.0.2.  I have not yet been able to install NI-Serial, so I cannot yet see if I have also restored my original problem -- the one that led me to have to upgrade NI-VISA and NI-SERIAL in the first place.
    Most importantly, there is now a "PXI Services v1.1.2" installed on the RT target.  I am quite sure the problem with MAX 4.0 not recognizing my PXI system has to do with the absence of this driver on the RT target.
    Thanks again for your interest and help,
    RonC

  • BI JDBC system does not appear in a search in Visual Composer of CE7.1

    Hi All,
    I have configured BI JDBC system in CE7.1 but it does not appear in a search in visual composter.
    I have using following connection parameter while configuration of BI JDBC system in CE 7.1.
    Oracle Deriver - classes12.jar / ojdbc14.jar
    Connection URL - jdbc:oracle:thin:@xx.xx.xx.xx:1527:BWI;SYSTEM;xxxx
    Driver Class Name - oracle.jdbc.driver.OracleDriver
    Platform details for BI and CE 7.1
    OS AIX 6.1
    Database Oracle 10.2
    Apart from this I already check SAP Note 1247283,1169625,1138877,773401 but still is not working.
    Please help me on same.
    Thanks,
    Harshal

    Created BI master system and problem is solved.
    Edited by: Harshal Subhash Dusane on Aug 12, 2010 2:03 PM

  • Photos from the PC does not appear on iOS devices

    Win7-64 installed icloud 2.0. Iphone 4, iPad new (iOS 6)
    I put the photos in the folder uploads, they appear on your computer in the my photostream, but do not appear on ios devices.
    Climbed into the iPhone file manager and found an interesting picture. Photos taken on iOS go to one folder photostream and displayed on all devices and PCs, but throw in uploads pictures in Windows also went on iOS devices, but for some reason in a completely different location. And in the photostream on iPhones and aypade not appear, although present. I wonder what this folder is and whether it is in others?
    Reset iphone now tried, does not help.

    Come on, surely no one can see one or two folders on the iphone?

  • Your system does not appear to have intel rapid start technology

    I have a Lenovo U310 with windows 8 and wish I could take it back. Problem after problem with this computer, both hardware and software related. I started getting this message about the Intel rapid start a couple of days ago. I went into this forum and one of the specilists suggested going into BIOS and change the SATA controller working mode to RAID and to enable IRST which I did. Now the computer can not start. It tries to load and it says that the recovery system failed. I can get to the BIOS menu again but I wont let me get to configuration screen. Any help would be much appreciated. thanks 
    Solved!
    Go to Solution.

    hi yzarate,
    I'm sorry to hear what happened,
    If the system is giving you a failed to start Option,  Restarting it May sometime give you option Like Safe mode,
           If you're getting that, select that option and it should be able to start you system while in RAID then restart the system again once booted back up.
    If you're not getting that message I would suggest go back to BIOS
               go to the Exit TAB, Select Load optimized default or press F9 to load defaults, F10 to save and Exit and hit enter,
    Try loading BIOS again and see if the configuration tab will be available,
    Best Regards
    Solid Cruver
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Atributes list to create target group does not appear

    Hi experts,
    In CRM Portal, It is not showing the page which I can choose Attributes list in order to create profile groups and target groups.
    I'm looking for something similar as tcode: CRMD_MKTSEG in SAP GUI.
    I have already assigned Marketing Manager/Assistant in my profile.
    Does anybody could help me ?
    regards,

    Hi,
    Assign Transaction category CRMD_MKTSEG to your user role for GUI as well as Portal(PCUI),
    u'll see the Segment Builder tab in PCUI screen, u can create profile/sets and target groups.
    Thanks,
    Dipesh.

  • User created in ECC system does not appear in Identity management

    Hi all,
    For the already new built GRC system, I am trying to configure buidling blocks 678: RiskAnalysis and Remediation.
    1- In section 5.2 (5.2     Add Roles to Existing Users in User Management Engine) I have to add roles to the users which were created in ECC system. But in Identity management I could not see those ID's existing.
    2 - I could not see these roles RE_ADMIN and CC_ADMIN in UME
    Could anybody help me moving forward.
    Thanks
    Lakshmi

    Hi,
    > 1- In section 5.2 (5.2     Add Roles to Existing Users in User Management Engine) I have to add roles to the users which were >created in ECC system. But in Identity management I could not see those ID's existing.
    >
    Have you defined Master User Source in RAR ?
    > 2 - I could not see these roles RE_ADMIN and CC_ADMIN in UME
    >
    Initially you have to upload Roles in Identity management. There will be 3 files:
    cc_ume_roles.txt
    ae_ume_roles.txt
    re_ume_roles.txt
    Upload them in identity management then you will get these roles.
    Thanks
    Sunny

  • Mail sent from my iPad does not appear on desktop (windows) pc

    Have had to change my BT Yahoo email account to BT Mail so on the iPad deleted the BT yahoo account and then added the BT mail account.  Problem is that mail sent from iPad no longer appears on the (windows) pc. What am I missing
    ipad iOs 7.1.2

    If it is IMAP, then obviously something is wrong. I don't know if there is a problem on the computer setup. Are you sending the email from a web browser or from an email client? I don't think that should matter anyway unless you have incorrect settings in the email client.
    Have you tried sending an email from your computer and see if it shows up as sent mail on the iPad?  Have you considered deleting the account and then add it back yourself on the iPad?

  • HT1918 The 'None' option from Payment Type does not appear, what's wrong?

    I can't remove my credit card from iTunes.

    You may have an outstanding balance, or be in a region that doesn't support this feature.

  • GDM does not appear back after logging out from Gnome.

    Hello,
    I am tryingout Archlinux for the first time. I am able to goto run level 5 and after booting I get the GDM login screen. I can log in to Gnome. But when I log out from Gnome, GDM does not appear, but I get a black screen. Then, the only way to come out is to press the reset button.
    What may be the problem?
    Thanks for your help.
    Anand

    it may depend on how ur running gdm, (possibly with -*no-daemon option) .. in which case it'd prolly werk if u removed it...
    although i'd recommend using rc.conf instead as it's a lot cleaner...
    to use /etc/rc.conf
    add gdm to the DAEMONS;
    mine = "DAEMONS=(gdm @syslog-ng @network @alsa @httpd)"
    that starts gdm(in daemon mode), then starts syslog-ng,net*,alsa and apache in the background .. save me about 6 seconds when i background em.
    then you need to change the default runlevel in /etc/inittab to 3 (not 5)

  • Progress indicator icon does not appear in Sap Portal

    Hi experts.
    Currently, i Have developed a WD ABAP which contains a progress indicator icon. When I execute this WD from backend (R/3 via SE80) the Icon progress appears while the WD is recovering data, building structure, etc...
    The problem appears when I access to the scenary from SAP Portal, because from SAP Portal does not appear the Progress Icon. Someone can tell me why the icon is not appearing, and how Can i solve it???
    Thank in advance.
    Best regards

    Hi Thomas.
    First of all, thanks for your answer.
    My problem is that I can obtain a progress indicator icon (a circle moving) when I am inside of my Ivew, but I need to show this icon also in the first step, during the initialization. The initialization of my scenary is a hard process which spent a lot of time, and I wonder if is possible show a Process indicator Icon while all data are being recovery. This icon is showed when I run my webdynpro in the Backend, but this icon does not appears qhen the new Internet Explorer Windows is opened.
    Do you know how to show it???
    Thanks again.

  • Import Data Option Does not appear in navigation

    I need to test the import capabilities as a Developer, but I do not see the options that are referenced in the help.
    I installed NAV Dynamics 2013 R2 Developer Version on a development computer with "SQL Server 2014 - Developer" installed. I copied a demo company. The option "Import from Data File" does not appear under Departments/ Administration/
    IT Administration/ General. Many other options are also missing.
    I reviewed the security setting for the Domain User and enabled the db_owner and db_AccessAdmin for the user. It was installed with the same administrative user account and the user has SysAdmin rights.
    I assume that this is some sort of security/authentication issue, but I also saw references that certain things are disabled in the demo. I can perform most basic functions, but many administrative functions are not visible.
    How can I enable \the import capabilities?

    Hi Jim,
    this is a Dynamics CRM forum, for Dynamics NAV you can post your questions here:
    https://community.dynamics.com/nav/f/34.aspx
    My blog: www.crmanswers.net -
    Rockstar 365 Profile

  • I am using 10.6.8 and I cannot get an Imac to appear in workgroup manager, the mac is bound to both AD and OD. I have removed the bindings, rebuilt the mac and also removed it from bot system but still it does not appear in OD in work group manager.

    I have a mac which is connected to a network and is bound to both OD and AD with no issues on my server when I try to manage it through Workgroup manager it does not appear.
    I have unbound it , removed it from both systems completely and even rebuilt it but it still does not appear in WGM.

    If your server is 10.6 and your client is 10.7 you'll have to add it manually to WGM
    via mac address.  10.7 clients don"t automatically appear in 10.6 server wgm

Maybe you are looking for