Firewire power??? what is that?

i've heard of it but i don't know what it is....

FireWire is the Apple brand name for the IEEE 1394 interface. It's a way of connecting devices to your computer, something like the USB you'd be more familiar with. Firewire power presumably refers to the power going to a Firewire port: Wikipedia - Firewire

Similar Messages

  • In addition to my iMac, I have a Power Mac G4 (10.4.11 Tiger) which of course is pre-Intel.  I can boot up and use for about 5 minutes before the mouse freezes.  I believe something is   overheating.  What would that be - so I can have repairs done?  The

    In addition to my iMac, I have a Power Mac G4 (10.4.11 Tiger) which of course is pre-Intel.  I can boot up and use for about 5 minutes before the mouse freezes.  I believe something is
    overheating.  What would that be - so I can have repairs done?  The machine is the Digital Audio version, M7627LL/A and Serial Number XB******KXQ.
    <Edited By Host>

    Hello USME,
    'Tis a common problem on old Macs.
    Do as Allan says: open the door and blow out all the dust bunnies. Canned air from Wal-Mart or Radio Shack can be handy (though sort of expensive) especially for blowing through the back of the power supply. A cool Mac is a happy Mac.
    Be sure your Mac can breathe. The air intake is on the bottom of the case, so be sure a deep pile rug or too many papers on your desk are not blocking the air supply.
    Feel the power supply and the processor with your hand. They should be warm but not hot; if you have to move your hand away, that's too hot!
    Check the fan on the power supply, and on the processor if it has one. Take a flashlight and peer in the back of the (Mac) case through  the grille; make sure the fan is turning. If it's not, the power supply won't work for long.
    Fans are not considered serviceable, though they will succumb to mechanics of determination. A CPU fan is easy and straightforward.
    A fan replacement will not cure an already damaged power supply; the PS may already be done for. Used power supplies for a DA are hard to come by, and not especially cheap when found (c.$50). An entire  working DA or Quicksilver may often be found for under $100 on eBay, and swapping in your HD is easy and simple... this might be cheaper and more expeditious than repairing an expired DA. Replacing a power supply is fairly easy, but it's a nuisance and requires a 2mm Allen head wrench in addition to the usual #2 Phillips head screwdriver.
    In my experience, power supplies and CPUs are about equally likely to fail. There are a few other possibilities, but they are not nearly so common.
    Good luck!... Jon

  • What is the best way to transfer files from a Power PC G4 that has NO power?  Thanks.

    What is the best way to transfer files from a Power PC G4 that has NO power?   I have a newer iMac. Thanks.

    Remove the hard drive and get one of these USB hard drive adapters. http://tinyurl.com/a5l2htj Then plug the adapter into your iMac to see/retrieve the files.
     Cheers, Tom

  • HT1766 The screen shows problems with iCloud only choices are ignore or settings, however nothing I do will unlock it from this screen, cannot power off keeps that bubble on the screen. What do I do?

    The screen shows problems with iCloud only choices are ignore or settings, however nothing I do will unlock it from this screen, cannot power off keeps that bubble on the screen. What do I do?

    Try this now.
    Reboot the iPad by holding down on the sleep and home buttons at the same time for about 10-15 seconds until the Apple Logo appears - ignore the red slider - let go of the buttons.

  • What can I do to fix an old Power Mac G4 that gives an I/O error message when trying to access Entourage?

    What can I do to fix an ld Power Mac G4 that gives an I/O error message when trying to access Entourage?

    You mean when you try to just start it?
    Could be many things, we should start with this...
    "Try Disk Utility
    1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
    2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
    *Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
    3. Click the First Aid tab.
    4. Select your Mac OS X volume.
    5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
    http://docs.info.apple.com/article.html?artnum=106214
    Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
    (Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
    If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.

  • What is that little half-inch slot next to the power light in the front of a MacBook Pro for?

    What is that little half-inch slot next to the power light in the front of a MacBook Pro for? Anyone knows?

    Infrared port for the Remote Control. An extra item for you to buy.

  • HT1539 the digital copy disc uses a power pc application that is no longer supported by mac os x, what can I do to obtain my digital copy?

    the digital copy disc uses a power pc application that is no longer supported by mac os x, what can I do to obtain my digital copy?

    If the OP is asking a generic question about how to run a CD-ROM, DVD or other disc that had an executable program that was a PowerPC application, he would either have to:
    1.  Install Snow Leopard (with Rosetta) into a partition on his hard drive or an an external hard drive, for "dual-booting" if his Mac will still boot into SL; or
    2.  Install Snow Leopard (with Rosetta) into Parallels to run his disc in Mt. Lion:
                                  [click on image to enlarge]
    <Edited By Host>

  • HT4060 My ipad has been charging most of the morning but its still saying low power...what does that mean?

    I've been charging my ipad most of the morning but its still saying low power...what does that mean?

    iPad Charging
    "The fastest way to charge your iPad is with the included USB Power Adapter.
    iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter.
    When attached to a computer via a standard USB port (most PCs or older Mac computers) iPad will charge, but only when it's in sleep mode.
    Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain."

  • Can I charge my new ipod using firewire power adapter?

    Just got my new 30GB ipod and realised that it doesn't come with power adapter to plug in directly in power outlet.
    Can I use the firewire power adapter which I have leftover after my 3rd gen ipod died on me?
    Also can I use the firewire to connect it to my powerbook for charging and song transfer? I thought firewire is faster than usb2 then why new ipods don't come with firewire cable anymore?
    Many thanks.
    PowerBook G4   Mac OS X (10.4.5)  

    think if you do your research and read up you will see the USB2 is indeed faster than Firewire. I actually did a few test on a dual G5 using both the Firewire and USB2 and in all my test, USB2 was faster.
    If USB2 was faster for you, that's wonderful. I'm not about to start arguing with you over it.
    What I can tell you is that you're certainly in the minority if this was the case for you.
    USB2 has a theoretical maximum speed of 480Mbps. While this is certainly a higher number than Firewire 400's 400Mbps, Firewire will still vastly outperform USB2 in almost every case. It is near impossible to get anywhere close to 480Mbps with USB2. Even under ideal conditions, USB2 still has to contend with other processes on the machine, and other devices in the bus.
    This is the nature of USB's design.
    It is not uncommon for Firewire to reach near maximum speeds consistently. This has been proven time and time again.
    Like I mentioned already, if USB2 is faster for you... go ahead and use it. I'm not going to tell you otherwise.
    I'm quite sure I've done sufficient research on this, as well as many other people in this industry, and these forums. Perhaps it is you that might want to do a little more reading.

  • I I have a late 2005 power PC G5 that I want to bring back to life.  I need to replace the original hard drive, a Maxtor 250 GB Sata.  Can I replace it with modern drives, SATA 5-6 etc?

    I have a late 2005 power PC G5 that I want to bring back to life.  I need to replace the original hard drive, a Maxtor 250 GB Sata.  Can I replace it with modern drives, SATA 5-6 etc?

    I knew I should never get rid of my old G5's.  By the way, there is a browser still supported for the PPC, TenFourFox, if you're not using it already.  Go to the Floodgap website (they author it)  download it for free.  The only thing it doesn't support is the Flash plugin, but the browser works great. Other video types are supported.  It's based on Firefox, and runs most of the plugins and add-ons. It's very fast, and beats all other browsers on the browser compatibility and speed test.  That's now my default on my G5's.  Firefox and Safari are no longer supported.  As far as the OS, both Tiger and Leopard were solid for me.  The reason, as I stated before, was iMovie.  The version in Tiger with iLife was far superior to what Apple changed it to.  They 'dumbed it down' for the masses.  Even the newest iLife 11 on my Mac Pro quad isn't is good, in my opinion.  So Leopard should be fine for you.  It's a much larger browser in terms of sheer megabytes and disk space, but it's fine.  As far as getting an OS disc, I'm seeing Tiger for about $45.00, Leopard for $50 - 60.00 on that famous auction site.  As far as RAM, I have 8GB in my G5 2.3, but you should check Activity Monitor when you are running your apps.  See how much green slice you have left (unused RAM).  You might find you don't need eight.  A Mac Pro will grab more free RAM than a PPC machine will.  I have a hard time maxing out use of my 8 on the PPC.  Not true with the eight on my Mac Pro.  The OS doesn't hesitate to grab and use it.  You might be OK with 6GB on your PPC. More will not make you faster, as long as you still have free RAM available.  As far as backup on your resurrected machine:  look for a firewire enabled backup if can.  Use CCC (Carbon Copy Cloner) and make a clone backup.  Next time your PPC machine wipes out the hard drive, just take your Firewire drive and plug it into another PPC machine, and you can select it as your boot drive. You'll be back and running in five minutes.  You can also take the physical drive out of your enclosure, and put it in your tower to replace the failed drive, and you'll be back to where you were in less than ten minutes, OS and all.  The PowerMac has an 800 port, so you can do the 800 on the machine to an 800 port on your backup. A firewire 800 to 800 cable is only about $8.00.  It runs nice and fast through the 800 port.  I like the OWC Mercury Extreme enclosures.  They use USB, Firewire 800, and eSATA, so all your options are open.

  • What is Firewire?  What does it do? How do you get it to work on the MacPro-something I must purchase perhaps?

    What is Firewire? What does it do? How do I get it to work on my MacPro?  Do I purchase it?

    Firewire is a serial connector technology that Apple incorporated in its 1999 and later machines that can be adapted to Thunderbolt, Express/34, and PCMCIA.   It can't be adapted to USB.   Many hard drives have Parallel ATA to Firewire and Serial ATA to Firewire adapters.   Firewire in its 4 pin configuration was popular on Sony devices such as Camcorders in the iLink connector format.   Apple started with the 6 pin variety that has its own power.  In 2003 it started including Firewire 800 in the 9 pin format and shifted to all Firewire 800 until Thunderbolt became standard.  A few MacBook, iMac, iBook, and Powerbook models didn't have it at all.
    Mac Pro is a desktop computer from Apple.  MacBook Pro is a notebook computer.  Not knowing your computer's age, doesn't help us determine how to adapt it.  Go to your System Profiler and look for Mac Pro x,y or MacBook Pro x,y and tell us which you see, and what x,y values you see.

  • Is it possible to use the firewire power adapter for ipod to charge an Ipad

    There is information everywhere that the Ipad doesn't charge with low power adapters.
    The first power adapter I received with my first Ipod was the firewire power adapter and it allows intensities even higher than the 10 W Ipad adapter.
    Could this old adapter be used with Ipad
    Model n. A1070 output 12V 6.7 A if I believe what is written on it.

    You should only use a USB-type charger for the ipad. Any other charger is risking damage to the ipad.
    The ipad uses 5Volts at 2 amps for best charging. This is why it came with the wall charger.
    You can charge it with any 5 Volt USB charger as long as the output amps is approximately 1 amp or more. If the amps rating on the charger is less than 2 amps, it will charge slower, but it is safe. The ipad will only draw the current it requires, but any voltage higher than 5 volts is risking damage to the ipad.
    Hope this helps.

  • Many times my laptop s temperature getting vey hight,what does that means guys ?, Many times my laptop s temperature getting vey hight,what does that means guys ?, Many times my laptop s temperature getting vey hight,what does that means guys ?

    Many times my laptop s temperature getting vey hight,what does that means guys ?

    Try going to About this Mac, under Apple menu, more info, in the left column hard ware click power. Under battery info see what it says under battery health>condition. If not normal, the battery probably needs service (replacement). You want take it to the Apple store to have it replaced, as this can other more serious issues if left un-tended to.

  • Apple FireWire Power Adapter and iPod Classic

    I just looked through the user guide, and it doesn't mention anything positive or negative about using the Apple FireWire Power Adapter that came with my 3G iPod. Any chance I'm going to fry my new iPod if I try charging it with the Firewire Power Adapter?
    Thanks,
    Steve

    No, you will not fry your new iPod.

  • Will USA Apple Firewire power adapter cope with 240 volts?

    Hi, just bought an Apple OEM firewire power adapter, see here
    http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=330275832822&ssPageName=ADME: B:EOIBSA:US:1123
    Anyone know if this will this work without a voltage convertor in UK & Europe?
    It's for an iPod mini.
    I know one can charge by connecting to computer but it's more convenient to plug into the wall.
    Thanks for any help.

    Oh yes, thankyou for clarifying my mind on that.
    I also bought a syncing firewire cable from the same place while I was at it so she should just need one cable then to do both charging & syncing as long as the firewire works abroad.
    I'll inspect it when it comes & if in doubt we could leave the firewire power adaptor here for when she's in US & get a USB power adapter in UK for there & Europe.
    Or I could sell the firewire power adapter to keep things simple.
    Thanks a lot Chris.
    In case anyone has any experience using the firewire power adapter abroad I'd be interested.
    Thanks.

Maybe you are looking for