Génération exécutable autonome
Bonjour,
Je me permet d'écrire ce message pour vous faire part de mon problème.
Après avoir réaliser un VI, que j'ai inséré dans un projet, j'ai eu le besoin de générer un exécutable autonome pour le faire fonctionner sur un ordinateur ne possédant pas Labview.
Après avoir suivi la procédure donnée dans l'aide, j'ai obtenu different fichier dont l'exécutable.
Seulement, lors de l'essai sur l'ordinateur ne possédant pas Labview, le programme se lance, mais je ne peux pas sélectionner le port COM correspondant à celui ou est branché mon capteur (note: mon programme permet d'afficher les valeurs mesurées par le capteur ainsi que de lui communiquer des informations)
De plus un message d'erreur est apparu : " Echec lors du démarrage du serveur de mise au point "
J'aimerai donc savoir si quelqu'un a déja eu ce problème auparavant, ou si quelqu'un peut me donner une procédure plus complète de la génération d'un exécutable car je ne vois absolument pas ce qui ne va pas..
Ps: Je construit l'exécutable avec une version comportant le module application builder, donc je pense avoir ce qu'il faut pour générer cet exécutable.
Merci d'avance pour vos réponses.
Cela permétrait donc de pouvoir sélectionner le port COM au sein de l'exécutable. Je ne pensais pas qu'il serait nécessaire d'obtenir quelque chose de ce type vu que lors de la programmation nous n'avions pas de problème pour communiquer avec le port série.
Pensez vous que ce Runtime permet de se passer du moteur d'exécution ou non?
Y a t'il différentes versions de ce Runtime ? Si oui quelle version choisir?
Désolé si mes questions peuvent paraître idiotes mais je débute dans la génération d'exécutable.
Similar Messages
-
Acquisition et génération en parallèle
Un sujet probablement un peu récurrant mais je ne trouve pas vraiment de réponse adaptée à ce que j'essaye de faire.
Nous avons des cartes PCMCIA 6036E et nous faisons sur le terrain des mesures de pressions, déplacement,... via nos capteurs.
Déjà pour commencer, nous ne sommes pas dans le kHz, une simple acquisition à 100Hz voir 500Hz parfois pour piéger un défaut nous suffit.
Mais nous devons générer en parallèle des acquisitions, la génération de signaux assez simples par ailleurs une rampe (très lente,~20min) ou un simple carré.
Dans le dernier code que j'ai fait, çà marche dans les valeurs numériques à l'écran et pourtant la réalité physique sur le bornier me donne un retard aléatoire du début de génération de mon signal !!! En résumé, il y a déjà un retard à l'alumage de ma boucle mais en plus quand le programme donne un échantillon en génération de 2V par exemple et qu'il l'écrit dans le fichier d'enregistrement, en fait à la sortie il y a au moins 0.3 V de moins. C'est le bon signal mais en retard.
Mon code n'est sûrement pas un exemple et je ne suis qu'un programmeur occasionel mais je sèche ce coup-ci.
Quelqu'un a t'il un exemple simple d'acquisition (jusqu'à 16 voies) et génération de signal sur des fréquences assez basses ?
Merci,Bonjour,
Merci d’avoir posté votre question sur les forums de
National Instruments.
Afin de vous aider au mieux j’aurais besoin de quelques
précisions supplémentaires par rapport à la façon dont vous réalisez votre
application.
Pour réaliser l’acquisition de données, utilisez-vous notre
driver DAQmx ou bien DAQ traditionnel ?
L’acquisition et la génération se font elles en continu, ou
point à point et l’écriture sur fichier se fait elle dans la même boucle ?
Si vous travaillez en mode continu, la carte est en quelque
sorte autonome et il est donc possible que l’écriture sur fichier ne se passe
pas exactement simultanément avec la génération.
En fonction de vos réponses, je serais plus à même de vous
orienter vers un exemple correspondant au mieux à vos besoins.
Je vous remercie par avance pour votre réponse,
Bien cordialement,
Guillaume H.
National Instruments France
#adMrkt{text-align: center;font-size:11px; font-weight: bold;} #adMrkt a {text-decoration: none;} #adMrkt a:hover{font-size: 9px;} #adMrkt a span{display: none;} #adMrkt a:hover span{display: block;}
>> NIDays 2011, le mardi 8 février au CNIT de Paris La Défense -
Exécution d'un exécutable sur un ordi sans labVIEW
Bonjour,
J'ai créé un vi qui marche bien et l'ai transformé en exécutable grâce à la version 2012 de LabVIEW. Sur la station où j'ai créé ce .exe, l'exécutable fonctionne bien (normal, puisque la version de LabVIEW est installée sur ce poste). J'ai donc testé si mon application autonome pouvait être exécutée sur un autre poste qui ne comporte aucun logiciel LabVIEW. J'ai donc transféré mon application par mail et essayé de lancer le programme sur le poste cible.
Le système m'a alors demandé d'installer le moteur d'exécution de LabVIEW : (mon .exe s'appelle Application)
"impossible de trouver le moteur d'exécution de LabVIEW. Application requiert une version 2012 (ou compatible) du moteur d'exécution de LabVIEW. Pour corriger ce problème, contactez le vendeur de Application ou téléchargez le moteur d'exécution de LabVIEW à partir du site Web de National Instruments."
J'ai cliqué sur le lien proposé et je me suis retrouvé sur le site de NI où j'ai dû choisir une version de ce moteur d'exécution. Comme je ne savais pas trop laquelle choisir, j'ai pris la plus récente : LabVIEW Run-Time Engine 2014 SP1.
Peut-être me suis-je simplement trompé de version (j'aurai dû prendre la version 2012) ?
En tout cas cette version s'est effectivement installée sur le poste cible, mais lorsque j'ai de nouveau lancé mon exécutable, le même message que ci-dessus s'est affiché, comme si le système ne trouvais pas le moteur que je venais d'installer.
Malheureusement, ce courrieleur ne me permet pas de vous envoyer les trois fichiers créé par mon application Builder de construction d'exécutable (notamment le .exe). A la place, je vous envoye le programme d'origine ("base de nombres pseudo-premiers-forts.vi") et Application, mais en version compressée (les .zip sont autorisés).
Si vous arrivez à lancer mon programme depuis un poste sans logiciel LabVIEW, pourriez-vous m'indiquer comment vous avez fait (notamment quelle version du moteur d'exécution vous avez utilisé) ?
Résolu !
Accéder à la solution.
Pièces jointes :
Application.ini 1 KB
base de nombres pseudo-premiers-forts.vi 24 KB
Application.zip 151 KBBonjour perce-neige,
Vous avez eu la bonne intuition dans votre message, il faut le Runtime version X pour faire tourner un exécutable créer avec LabVIEW version X.
Vous pourrez télécharger le runtime ici :http://www.ni.com/download/labview-run-time-engine-2012/3433/en/
Et il n'y a aucun souci à avoir plusieurs runtime installés sur une même machine.
Bonne week-end,
Flo
Open Diagram First -
Impossible de créer un exécutable sous LabVIEW 2010
Bonjour,
J’ai une application écrite en LV8.2 qui tournait sans problème.
Je suis passé sous LabVIEW 2010, et j’ai une erreur au moment de créer un exécutable.
L'erreur 1 s'est produite à : Nœud de méthode dans AB_Build.lvclass:Copy_Files.vi->AB_Application.lvclass:Copy_Files.vi->AB_EXE.lvclass:Copy_Files.vi->AB_Build.lvclass:Build.vi->AB_Application.lvclass:Build.vi->AB_EXE.lvclass:Build.vi->AB_Engine_Build.vi->AB_Build_Invoke.vi->AB_Build_Invoke.vi.ProxyCaller
Raisons possibles :
LabVIEW: Un paramètre d'entrée n'est pas valide. Par exemple, si l'entrée est un chemin, celui-ci contient peut-être un caractère qui n'est pas autorisé par le système d'exploitation, comme ? ou @.
=========================
NI-488: La commande requiert un contrôleur GPIB comme contrôleur en charge.
Nom de la méthode : Linker:Write Info To File
Apres quelques recherches, j’ai isolé le sous VI qui causait problème.
C’est un .Net qui permet de lancer un fichier.pdf
Si je mets directement cette fonctionnalité dans le diagramme principale (sans passer par un sous VI), j’ai le message d’erreur suivant :
L'erreur 74 s'est produite à : Nœud de méthode dans AB_Build.lvclass:Copy_Files.vi->AB_Application.lvclass:Copy_Files.vi->AB_EXE.lvclass:Copy_Files.vi->AB_Build.lvclass:Build.vi->AB_Application.lvclass:Build.vi->AB_EXE.lvclass:Build.vi->AB_Engine_Build.vi->AB_Build_Invoke.vi->AB_Build_Invoke.vi.ProxyCaller
Raisons possibles :
LabVIEW: Mémoire ou structure de données corrompue.
Nom de la méthode : Linker:Write Info To File
Remarque : J’ai fais un petite appli qui n’utilise que ce VI et je n’ai pas le PB.
Quelqu’un à t’il une piste de recherche ?
Merci d’avanceBonjour,
Lorsque vous créez un exécutable veillez toujours à n'avoir que la fenêtre du projet d'ouverte, j'ai déja vu le cas et ce type d'erreur apparaître lorsqu'une fenêtre d'un VI qui devait être compilé était ouverte.
Pour revenir plus en profondeur sur le problème que vous rencontrez, je vous invite à toujours effectuer une recompilation complète de tout les VIs de votre projet lorsque vous passez d'une ancienne version à une nouvelle version. Cela peut régler votre problème, la recompilation va effectuer un certains nombre d'opérations de façon à rendre le VI "compatible" avec la version utilisée.
Pour cela : Outils » Avancé » Recompiler.
Cette opération peut s'avérer utile dans votre cas.
Cordialement,
Da Helmut -
Bonjour,
J'ai dévelloppé une application utilisant une centrale de mesure YKMX100. Le problème survient lorsque je génére l'exécutable et que je désire m'en servir sur un autre poste.
Lors de la génération de mon exécutable, j'ai bien mis tout les VIs nécessaire au bon fonctionnement de celui-ci (dont les VIs drivers de la centrale).
Mais lorsque j'essaye de me connecter à la centrale via mon exécutable (sur un poste ne possédant pas labVIEW), il me met :
ERROR -1073807346
??? dans YKMX100
Initialize.vi -> Test_connexion_MX100.vi
Je pens que vous pouvez vous appercevoir que l'erreur non explicite ne m'aide pas beaucoup à la résolution de ce problème ... merci de m'éclaicir sur ce point !Le poste que vous utilisez ne possède peut être pas de driver VISA. Le code erreur que vous donnez correspond à une erreur VISA. Si vous allez dans Expliquer l'erreur LabVIEW donne : La session ou la référence de l'objet donnée est invalide.
Avez-vous installé NI-VISA sur la machine?
Cordialement,
Julien -
Variable partagée entre 2 éxécutables sur deux machines en réseau
Bonjour, je désire communiquer par variable partagée entre deux éxécutables (créés en LV 8.6) sur deux machines différentes d'un même réseau local. Le noeud de méthode "déployer une librairie" me retourne une erreur dès que je place une ip différente de localhost ; d'une façon plus générale, l'exacte marche à suivre n'est pas très clair pour moi : qui déploie vers qui, necessité d'un "binding" ou pas, etc...Quelqu'un a t-il déja réalisé cette opération ? Merci d'avance...
Vincent
Solved!
Go to Solution.Bonjour,
Quel est précisément votre message d'erreur ? Pouvez-vous nous fournir votre VI afin de reproduire votre problème ?
Voici quelques tutos :
sur la technologie PSP pour les variables partagées publiées sur un réseau
Network Variable Technical Overview
Ainsi que quelques KB traitant du sujet :
Comment déployer des variables partagées publiées sur le réseau
Can I Use Multiple Network Cards with LabVIEW?
Deploying Shared Variables to a Specific Network Card
Et sur les messages d'erreur rencontrés :
Troubleshooting Network-Published Shared Variables
Shared Variable Error Explanations
Cordialement,
Message Edité par Steve Mohamed le 01-28-2009 05:32 PM
Steve M.
National Instruments France
#adMrkt{text-align: center;font-size:11px; font-weight: bold;} #adMrkt a {text-decoration: none;} #adMrkt a:hover{font-size: 9px;} #adMrkt a span{display: none;} #adMrkt a:hover span{display: block;}
>> Vidéo-t'chats de l'été : présentations techniques et ingénieurs pour répondre à vos questions -
Erreur de génération de contenu. [Erreur: Ressource non valide]
Please help I've this stupid message and I don't know why… I checked each link
Erreur de génération de contenu.
[Erreur: Ressource non valide]Bonjour Kant,
J'ai tenté de faire une construction basée sur le même VI et dans la même version de LabVIEW que vous; je n'ai pas rencontré de souci pour l'heure.
Je suppose que partant du VI où vous avez enlevé le VI de décimation, après enregistrement de votre VI, si vous replacez le VI de décimation, vous obtenez le même résultat.
Pouvez-vous, à partir d'un nouveau projet, construire un exécutable basé sur VI qui contient uniquement le VI de décimation en question?
Vous pourriez aussi tenter de recompiler toute la hiérarchie de votre VI en faisant Ctrl+Shift+Click sur Run.
Bonne journée,
Flo
Open Diagram First -
<p>Hi </p><p>I am trying to design crystal reports in rational application developer on linux. <br /></p><p>But I cannt find CRDB_JavaServer.ini on linux. This file is present in Windows </p><p>in c:\program files\crystal decisions\2.5\bin path.But I cannt seem to find this file in linux.</p><p>I am running RAD 6011 ifix001,ifix002 and can see the Crystal Reports JSP Tags drawer in JSP design view.</p><p>But I cannot find "Crystal report" as one of the file types , when i right click on WebProject\WebContent folder</p><p>to create a new Crystal Report in my Web project. </p><p> </p><p>Any help would be much apprecated. </p><p>robin. </p>
<p>I don't know much about this and I'm assuming you already did a find or locate command.</p><p>Did you find a CRConfig.xml. This file had replaced the old CRDB_JavaServer.ini in newer versions. I'm not sure which one IBM was using for this build. If you have a support contract with IBM I would suggest talking to them as they handle first line support for this. It could be that they forgot to include the file by mistake. </p><p>Rob Horne<br /><a href="/blog/10">Rob's blog - http://diamond.businessobjects.com/blog/10</a></p>
-
Lan connectivity Issue on autonomous AP with throttles
Hello,
I encounter a strange problem on several AP 1242 in version 12.4(25d)JA1 of a customer :
He has 10 autonomous AP covering a factory and is using them for laptop connectivity and TOIP with mainly 7921 Cisco Wifi Phones.
The phones are configured to use only 802.11a.
The APs loose LAN connectivity randomly and therefore the clients don't work anymore.
The AP are connected on a 2960 and a 3560 wich are in turn connected on a 3750 wich route the trafic.
After checking spanning-tree no loops are present.
When I check the counters on the AP involved I see the "trhottles" and "ignored" counters incrementing on the fa0 link of the AP impacted wich mean I think it can't handle the incoming traffic. This incoming traffic seems not to be too big however. I can see drops on the switch interface connecting the AP.
There is a lot of roaming on the AP due to people walking in the factory with their wifi phones.
Here is a view of the fa0 counters :
AP1242-LOGIST#sh int fa0
FastEthernet0 is up, line protocol is up
Hardware is PowerPCElvis Ethernet, address is 001d.a1ce.26e2 (bia 001d.a1ce.26e2)
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Full-duplex, 100Mb/s, MII
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/160/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 81000 bits/sec, 53 packets/sec
5 minute output rate 29000 bits/sec, 26 packets/sec
7447113 packets input, 674891974 bytes
Received 286839 broadcasts, 0 runts, 0 giants, 549631 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 549631 ignored
0 watchdog
0 input packets with dribble condition detected
4422100 packets output, 609868806 bytes, 0 underruns
0 output errors, 0 collisions, 4 interface resets
1 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Here is a small part of logs concerning roaming, i don't see errors or log indicating that something is wrong nor in the switches log :
Jun 6 12:57:27.007: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP001E4A3EE15D 001e.4a3e.e15d Associated KEY_MGMT[WPAv2 PSK]
Jun 6 12:57:42.499: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 12:58:02.620: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 12:58:03.653: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 12:59:15.564: %DOT11-6-ROAMED: Station 588d.09d3.a92b Roamed to 001e.134c.5a50
Jun 6 12:59:15.564: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 12:59:41.905: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 442b.0355.ab28 Reason: Previous authentication no longer valid
Jun 6 12:59:54.728: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP442B0355AB28 442b.0355.ab28 Associated KEY_MGMT[WPAv2 PSK]
Jun 6 13:01:12.541: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 13:02:35.841: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 001e.4a3e.d875 Reason: Previous authentication no longer valid
Jun 6 13:02:36.489: %DOT11-6-ASSOC: Interface Dot11Radio0, Station ec85.2f7c.c837 Associated KEY_MGMT[WPAv2 PSK]
Jun 6 13:03:29.256: %DOT11-6-ROAMED: Station 588d.09d3.a92b Roamed to 001e.134c.5a50
Jun 6 13:03:29.256: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 13:04:32.754: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP001E4A3ED875 001e.4a3e.d875 Associated KEY_MGMT[WPAv2 PSK]
Jun 6 13:06:47.858: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 001e.4a3e.e15d Reason: Previous authentication no longer valid
Jun 6 13:07:18.107: %DOT11-6-ROAMED: Station 001f.6c7a.5101 Roamed to 001d.a2bb.15b0
Jun 6 13:07:18.107: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 001f.6c7a.5101 Reason: Sending station has left the BSS
Jun 6 13:07:38.109: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 13:07:42.031: %DOT11-6-ROAMED: Station 588d.09d3.a92b Roamed to 001e.134c.5a50
Jun 6 13:07:42.031: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 13:07:46.489: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP001F6C7A5101 001f.6c7a.5101 Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 13:08:27.712: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 13:08:44.502: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 13:08:44.572: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Associated KEY_MGMT[WPAv2 PSK]
Jun 6 13:08:56.778: %DOT11-6-ROAMED: Station 588d.09d3.a92b Roamed to 001e.134c.5a50
Jun 6 13:08:56.779: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 13:09:17.874: %DOT11-6-ROAMED: Station 001f.6c7a.5101 Roamed to 003a.9a92.8d70
Jun 6 13:09:17.874: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 001f.6c7a.5101 Reason: Sending station has left the BSS
The AP are configured as follow :
Current configuration : 5184 bytes
! No configuration change since last restart
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP1242-LOGIST
logging rate-limit console 9
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
clock timezone gmt+1 1
clock summer-time gmt recurring last Sun Mar 2:00 last Sun Oct 3:00
dot11 syslog
dot11 vlan-name Data vlan 11
dot11 vlan-name Voix vlan 14
dot11 vlan-name Webguest vlan 5
dot11 ssid WLAN_data
vlan 11
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii 7 10600C0E261B173C252203797479633F371A29
dot11 ssid WLAN_voice
vlan 14
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii 7 080F49592A1500203B2D25567A7A7622263C0C
dot11 ssid Webguest
vlan 5
authentication open
mbssid guest-mode
dot11 wpa handshake timeout 1000
dot11 arp-cache
dot11 priority-map avvid
dot11 phone
power inline negotiation prestandard source
class-map match-all _class_voice0
match ip dscp ef
class-map match-all _class_voice1
match ip dscp cs3
policy-map voice
class _class_voice0
set cos 6
class _class_voice1
set cos 3
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 11 mode ciphers aes-ccm
encryption vlan 14 mode ciphers aes-ccm
ssid WLAN_data
ssid WLAN_voice
ssid Webguest
mbssid
power client 17
channel 2472
station-role root
dot11 qos class voice local
admission-control
admit-traffic narrowband max-channel 75 roam-channel 6
dot11 qos class voice cell
admission-control
no cdp enable
infrastructure-client
interface Dot11Radio0.5
encapsulation dot1Q 5
no ip route-cache
no cdp enable
bridge-group 5
bridge-group 5 subscriber-loop-control
bridge-group 5 block-unknown-source
no bridge-group 5 source-learning
no bridge-group 5 unicast-flooding
bridge-group 5 spanning-disabled
interface Dot11Radio0.11
encapsulation dot1Q 11
no ip route-cache
no cdp enable
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface Dot11Radio0.14
encapsulation dot1Q 14
no ip route-cache
no cdp enable
bridge-group 14
bridge-group 14 subscriber-loop-control
bridge-group 14 block-unknown-source
no bridge-group 14 source-learning
no bridge-group 14 unicast-flooding
bridge-group 14 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 11 mode ciphers aes-ccm
encryption vlan 14 mode ciphers aes-ccm
ssid WLAN_data
ssid WLAN_voice
ssid Webguest
no dfs band block
mbssid
channel dfs
station-role root
interface Dot11Radio1.5
encapsulation dot1Q 5
no ip route-cache
no cdp enable
bridge-group 5
bridge-group 5 subscriber-loop-control
bridge-group 5 block-unknown-source
no bridge-group 5 source-learning
no bridge-group 5 unicast-flooding
bridge-group 5 spanning-disabled
interface Dot11Radio1.11
encapsulation dot1Q 11
no ip route-cache
no cdp enable
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface Dot11Radio1.14
encapsulation dot1Q 14
no ip route-cache
no cdp enable
bridge-group 14
bridge-group 14 subscriber-loop-control
bridge-group 14 block-unknown-source
no bridge-group 14 source-learning
no bridge-group 14 unicast-flooding
bridge-group 14 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
speed 100
full-duplex
no cdp enable
hold-queue 160 in
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
no cdp enable
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.5
encapsulation dot1Q 5
no ip route-cache
no cdp enable
bridge-group 5
no bridge-group 5 source-learning
bridge-group 5 spanning-disabled
interface FastEthernet0.11
encapsulation dot1Q 11
no ip route-cache
no cdp enable
bridge-group 11
no bridge-group 11 source-learning
bridge-group 11 spanning-disabled
interface FastEthernet0.14
encapsulation dot1Q 14
no ip route-cache
no cdp enable
bridge-group 14
no bridge-group 14 source-learning
bridge-group 14 spanning-disabled
service-policy input voice
service-policy output voice
interface BVI1
ip address 10.17.10.5 255.255.255.0
no ip route-cache
ip default-gateway 10.17.10.254
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
logging trap warnings
logging 10.15.51.115
no cdp run
bridge 1 route ip
line con 0
line vty 0 4
sntp server 10.15.1.50
sntp broadcast client
end
Does someone ever experienced a similar problem ?
When I shut radio interfaces they're is no more problems on the LAN. Can this be an overlapping coverage issue ?
Can someone please give me advices on how to troubleshoot this issue ?
Thank you in advance as I'm a bit stuck.
Best Regards,Hi Scott,
Thanks for your reply.
Do you think this can be the origin of the issue my customer encounters or is it only to be standard ? As this change will have to be made on all clients, if there is a chance it solves the problem I will do it ASAP, if not I will delay it in a less busy period :-)
Can the constant roaming associations and dissasociations overload the AP and make it stop responding on the LAN or is it only a throuhput problem ?
Thanks in advance for your answer.
Best Regards, -
Issue with Vacation Pro-ration
We generate quotas via RPTQTA00 and not time evaluation.
We have a group of employees who are across all employee sub -gruoups who get 20 vacation days per calendar year, which is pro-rated upon hire. we adjust their IT41 Vacation Service Date (through dynamic action) to 5 years prior to their Hire Date, in order for the increase in Vacation from 15 to 20 days to be picked up as per our Base Entitlement table entries.
The system generates quota 1 day less than it should.
Eg:if an employee was hired on 1 july 2009 and bsed on the dynamic action it populated IT41 with the vacation service date of 1July 2004.
Our base entiltlement rule is 60-999 months 20 days per calender year.
Vacation service date is 1 july 2004.
When i create a quota in infotype 2006 it generated 9 days instead of 10 days.
What could be the problem.
I tried using the HDATE and ENTRY feature.
We even tried using 'Key Date for Determining Seniority' in 'Define Generation Rules for Quota Type Selection as Vacation service date(Sub type 15), However, when this configuration change is made the 5th anniversary year pro-ration does not work.
Pls help.
Shyam.I have exactly the same problem.
But since I download the las update, everitime i conect it both displays just turn black and i just see the mouse's pointer. -
Has anyone who has implemented pension pro-ration based on WPBP splits experienced problems with loans being recovered through the payroll?
We have recently activated node 9 of feature GBCHG - 'Proration based on WPBP splits.' We have now discovered a problem in that gross pay recoveries are not being included in the pension calculation. The gross pay recoveries are set up as loans in IT0045. SAP standard wage types /LOP, /LRP etc are created and we then copy the values from these wage types on to custom wage types.
All other gross payments and deductions are being correctly considered for the pension calculation with the exception of the gross pay recovery. Iu2019ve been through the configuration of the wage types and cannot see any reason why they would not be considered for pension.
Any thoughts or suggestions that you may have would be greatly appreciated!
Thanks
DanCheck if it helps to you..with SAP Notes
1295699 - Employer pensionable pay incorrect.
1607869 - Processing class setting for SxPE wagetypes
1428418 - Incorrect employer pensionable pay calculation
1441895 - Incorrect values in SxPR/N/E Wagetypes during WPBP proration
Mohan -
Trunking issue with autonomous AP
I was at a customers that wanted a new ssid configured on his 20 1252 AP's and to stand up a new one with the olds and new SSID on it. Added the vlans, trunked them down and configured the interfaces and SSID's on the existing AP's no biggie. The new AP(not really new been kicking around in a lab) is giving me some weird issues. I deleted the exisiting config from it and took one of the running configs fromm the others that are working, modified the name and ip and pasted it in. This should have worked just fine. However the trunk port on the 4507 will not come up. The radio's are up and so is the BVI, however I cannot ping to it since the trunk is down. I started looking at the config and the thing I notice is that the AP's are in vlan 2, and the native vlan is set for vlan 2 on all the working trunk ports on the switch. However the AP's do not have vlan 2 on them, and their native vlan is 1. This should not work! I always thought the native had to match on both sides?? In any case I am probably missing something stupid, I have been up since 4am it was a 4 hour drive to get here. Oh and I have to go back and make firewall changes at midnight. Here is the relavent configs please let me know if its something stupid I usually do a lot of controller based installs havnet done a autonomous one in years. Thanks!
Here is a port on the switch
interface GigabitEthernet3/9
description AP 1 - SMT
switchport access vlan 2
switchport trunk native vlan 2
switchport trunk allowed vlan 2,9,15
switchport mode trunk
end
Here is the AP hanging off that works fine
cstwap01#sh vlans
Virtual LAN ID: 1 (IEEE 802.1Q Encapsulation)
vLAN Trunk Interfaces: Dot11Radio0
Dot11Radio1
GigabitEthernet0
This is configured as native Vlan for the following interface(s) :
Dot11Radio0
Dot11Radio1
GigabitEthernet0
show run on the AP
dot11 mbssid
dot11 vlan-name VoIPVLan vlan 9
dot11 vlan-name Wireless-101-Legacy vlan 15
dot11 ssid 101
vlan 15
authentication open
mbssid guest-mode
dot11 ssid VoIPVLan
vlan 9
authentication open
mbssid guest-mod
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid 101
ssid VoIPVLan
interface Dot11Radio0.9
encapsulation dot1Q 9
no ip route-cache
bridge-group 9
bridge-group 9 subscriber-loop-control
bridge-group 9 block-unknown-source
no bridge-group 9 source-learning
no bridge-group 9 unicast-flooding
bridge-group 9 spanning-disabled
interface Dot11Radio0.15
encapsulation dot1Q 15
no ip route-cache
bridge-group 15
bridge-group 15 subscriber-loop-control
bridge-group 15 block-unknown-source
no bridge-group 15 source-learning
no bridge-group 15 unicast-flooding
bridge-group 15 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface GigabitEthernet0.9
encapsulation dot1Q 9
no ip route-cache
bridge-group 9
no bridge-group 9 source-learning
bridge-group 9 spanning-disabled
interface GigabitEthernet0.15
encapsulation dot1Q 15
no ip route-cache
bridge-group 15
no bridge-group 15 source-learning
bridge-group 15 spanning-disabled
interface BVI1
ip address 10.190.2.51 255.255.255.0
no ip route-cache
ip default-gateway 10.190.2.1Hello Mike,
actually, native VLAN doesn't have to match on two sides of a trunk, in fact it's quite common with autonomous APs. Your BVI1 is usually tied to a native VLAN 1, but switch port native VLAN is usually configured for whatever VLAN you want AP's management IP to belong to, in your case VLAN 2.
When you connect two catalyst switches together with a trunk that has different native VLAN configured on two sides, you will keep getting logging messages warning you about it. It's not recommended, but some scenarios require such setup.
Something else is wrong, maybe a physical issue. When you say the trunk is down, do you mean the interface is down ? Can you paste config of bad switch port and bad AP?
Regards,
Roman -
Autonomous Transactions and table locks
Does a commit statement in an Autonomous Transaction block in PL/SQL release locks aquired in the master transaction block?
e.g
CREATE OR REPLACE PACKAGE test_auto_trans AS
PROCEDURE mainproc;
PROCEDURE testproc;
END test_auto_trans;
CREATE OR REPLACE PACKAGE BODY test_auto_trans AS
/*****************Main Procedure*********************/
PROCEDURE mainproc AS
BEGIN
LOCK TABLE a,b,c IN EXCLUSIVE MODE nowait;
/*some processing involving tables a,b,c here. no commit done yet*/
testproc();
/* will the locks on a,b,c still be available here? */
EXCEPTION
WHEN others THEN
dbms_output.put_line('Error');
dbms_output.put_line(sqlcode);
dbms_output.put_line(sqlerrm);
RAISE;
END mainproc;
/*****************test Procedure*********************/
PROCEDURE testproc AS
PRAGMA AUTONOMOUS_TRANSACTION;
BEGIN
/*some processing using tables a,b,c here*/
commit;
EXCEPTION
WHEN others THEN
dbms_output.put_line('Error');
dbms_output.put_line(sqlcode);
dbms_output.put_line(sqlerrm);
RAISE;
END testproc;
END test_auto_trans;
/No transaction will release the locks held by another transaction. When you declare a stored proc to be PRAGMA AUTONOMOUS_TRANSACTION, it is essentially the same as if you logged in as the same user but in a different session.
For example, if I have two sqlplus sessions running as user a, if I do an update in session1 and a delete and commit in session 2 I can still rollback in session 1.
However, your psuedo code as posted will not work at all since the call to test_proc will block until you commit in the main proc, and since test_proc will never return, the main proc will never get to commit. It is exactly analogous to the following:
session1> SELECT * FROM t;
ID DESCR
1 One
2 Two
session1> LOCK TABLE t IN EXCLUSIVE MODE nowait;
Table(s) Locked.
session1> UPDATE t SET descr = 'Un'
2 WHERE id = 1;
1 row updated.so far, this is your main proc. Now, in another session (which is equivalent to your autonomous transaction procedure), I do:
session2> UPDATE t SET descr = 'Deux'
2 WHERE id = 2;which as I type is still waiting on the commit from session 1. Therefore, I cannot get to commit the autonomous transaction which would return control to session1
HTH
John
Message was edited by:
John Spencer
Sorry, I initially forgot to answer your actual question "what about DML statements like truncate". Since TRUNCATE is actually a DDL statement I will assume that is what you meant. My initial answer covers DML statements (except SELECT which will work).
All DDL statements in Oracle go
COMMIT
DDL statement
COMMIT
since the initial commit requires a very brief exclusive lock, you will get an error like:
ORA-00054: resource busy and acquire with NOWAIT specified
Exactly as if you did:
session1> LOCK TABLE t IN EXCLUSIVE MODE nowait;
Table(s) Locked.then tried to do it again the another session
session2> LOCK TABLE t IN EXCLUSIVE MODE nowait;
LOCK TABLE t IN EXCLUSIVE MODE nowait
ERROR at line 1:
ORA-00054: resource busy and acquire with NOWAIT specified -
How do I set the aspect ration for 4:3 or for 16:9?
How do I set the aspect ration for 4:3 or for 16:9 in Adobe PE12?
PulcinellaNM
What computer operating system is your Premiere Elements 12 running on? Have you updated from 12 to 12.1 Update via a project's Help Menu/Update? If not, please do so. That is all background information for now.
As for the question that you are posting....
I think we need to go a lot deeper into what you are doing. Here are some considerations
The aspect ratio setting is in the import settings. In Premiere Elements 12 Expert workspace, the project automatically sets the project preset based on the properties of the first video file that you drag to the Expert workspace Timeline. If your video's properties include a 16:9 flag, then the project settings will have a 16:9 flag (aspect ratio). If you do not want the project to set the project settings automatically, you can set the project settings yourself manually with File Menu/New/Project and then import your source video.
If a problem exists where imported 16:9 video is presenting in Premiere Elements as 4:3 instead of 16:9 (typical of the JVC .mod file issue), then you can set the pixel aspect ratio under Interpret Footage feature inside the project workspace.
At this point, I think it best for you to give more details and background behind your question so that we can be sure that we are giving you the information that you need to succeed in your projects.
If you need clarification on anything written, please do not hesitate to ask for clarification.
Thank you.
ATR -
How can I export the report to Excel or CSV format in Rational(Java)?
<p>Dear all,</p><p>Now I develop CR report integrate with Web application, I use Ratioanl(RAD) to develop. And I want to export the report to Excel/CSV format, but always failed.</p><p>If I force it export CSV file in the system, when I use MS office to open this CSV file, the file content is bad.</p><p>Could any one tell me how to achieve this?</p><p> Many thanks!</p><p>Steven</p>
<p>CR4E is bundled with RAD 7...actually to be clear it is a version of CR4E Professional. Users of RAD 7 will also get a dev/test license of CR Server as well as number of additional features to support developing applications against their BusinessObjects Enterprise or Crystal Reports Server systems. For more information regarding the RAD 7 launch you can read the press release here:</p><p><strong><a href="http://biz.yahoo.com/bw/061205/20061205005363.html?.v=1">http://biz.yahoo.com/bw/061205/20061205005363.html?.v=1</a> </strong> </p><p>I am hoping to do a webinar in January highlighting a number of the new features available with the IBM Rational Application Developer integration.</p><p>As for RAD 6 support, unfortunately the CR4E toolkit does require Eclipse 3.2 support so it will not work with RAD 6. </p><p>Regards,<br />Sean Johnson (CR4E Product Manager) <br /><br /> <strong><a href="http://www.eclipseplugincentral.com/Web_Links-index-req-ratelink-lid-639.html">Rate this plugin @ Eclipse Plugin Central</a></strong> </p>
Maybe you are looking for
-
I cannot download Adobe Reader app using my IPod Touch 4th Generation due to iOS upgrade.
I have an IPod Touch 4th Generation (the older model) and the highest operating system stops at iOS 6.1.6. Unfortunately, when I tried to download Adobe Reader app, it only works for the newer IPod Touch 5th Generation with an operating system of iOS
-
Until recently I was able to send images in the body of my Yahoo emails. Now, I am getting the message "This message has been truncated", and the email does not go through. I do not have this problem using IE. Could you please help? Thank you.
-
To generate a .prn for the report
hello, i have a little problem. i m working wih reports 9i and the output is generated in PDF format. i want to know how to generate a .prn file for the shown report,if possible from the report or the form thru which the report is being called, coz w
-
Connecting macbook air to my ipad
I want to connect my Macbook air with my ipad but for some reason they connect recognise each other but won't allow anything to transfer between them. Any ideas?
-
Javascript access to submit in TileView
Here is a working example of doing a submit on a javascript action in the ViewBean page: document.RequestListPage.action='../main/RequestListPage?RequestListPage.hiddenButton=&jato.pageSession=' document.RequestListPage.submit(); What would the code