"Guest Network" VPN

I'd like to setup a network account on Lion Server and allow that account to VPN in to my server. But I want this account to have limited access to my LAN, similar to how the stovepiped "Guest Network" works with Airport Extremes. I don't see any way to assign specific network accounts specific IP ranges outside the normal, say, 10.0.1/24. Is there even any way to assign a specific account something in the range,say, 10.0.2/24? Any way to further limit network access for Lion Server VPN sessions?

Thanks for the acl suggestion for the fs. Yes, of course you're on the same network when you VPN in. But Server app doesn't appear to have any way to assign different accounts or different groups to a different subnet, say 10.0.2/24. Then this "guest network" subnet could be acl'd appropriately for various services. Is anyone aware of a way with Server app or Profile Management or something to assign variable subnets with VPN?

Similar Messages

Can I use the guest network on a AE connected to a Cisco RV180?

I have not been able to connect to the guest network on my AE with a Cisco RV180 as the gateway. I read in an older post that the guest network my not work on all equipment, that it must be connected to a "simple" modem. Just want to find out if the Cisco is compatable.

The AirPort Express does need to connect to a simple modem in order for the Guest Network feature to work correctly.
According to Cisco the RV180 is a VPN Router, so it would not be compatible with the AirPort Express for the purpose that you ask about.
Cisco RV180 VPN Router Data Sheet [Cisco Small Business RV ...

Guest network does not work when bridging airport express to extreme

Hello everyone,
i just upgraded my airport extreme 5th gen and airport express (dual band) to 7.6.3 which is supposed to enable guest network extenstion..
my airport extreme is hardwired to airport express (set as bridged mode), eveything works fine with internet connectivity and roaming between the two since both are set with the same ssd name and wpa pass, i have enabled guest network on both to test the new update, which worked fine with airport extreme, then i went downstairs to test airport express guest network which didnt work.. i can see and join the network, IPs are set correctly exactly like airport extreme.
while testing airport express guest network i noticed that i can only browse google website or google search results, youtube website can be accessed too but it will not broadcast youtube videos.. any other website cannot be accessed thru airport express guest network..
since airport express guest network is providing a very limited access i tried enabling vpn on my iphone and managed to get full access with extremely slow speed.. can this be a bug on the firmware, did anyone find a solution???
Thanks

AirPort Extreme is the main base station handlng DHCP and NAT for the network. Normally, I do not use the Guest Network feature of this dual band router, but decided to check out the new firmware.
The AirPort Express is normally connected back to the AirPort Extreme via a wired Ethernet connection so it functions as a separate access point in a roaming network configuration.
I tried out the Guest Network option in the new firmware on the AirPort Express and had no issues. Then, decided to try the Express out as a test connecting using wireless only. I moved it to a location that was about 30 feet and a few rooms away from the AirPort Extreme and enabled the Guest Function with no problems.
I would not expect your setup to work with the Guest Network features, since you do not have an Apple router installed and functioning as the main router for the network. That would be the device that "creates" the Guest Network and other AirPorts "extend" it using either an Ethernet or wireless connection.
Apple used VLAN for the Guest Network feature before and I assume that has been expanded somewhat with the new feature to extend the Guest Network option to other Apple routers on a network.

Guest networking issues

On my old Airport Extreme I could not connect it down stream from my main router AND use guest networking, it had to be one or the other.
Has this been addresses in the 5th gen AE?

Im not wanting to extend my guest network.
My main router (a $1200 Cisco business VoIP VPN router) is 50 meters away from my house in a different building. I have a network cable run from this main router into my house and it's there, in my house, that I want wifi and guest access.
Ive had several other brand routers in my house, currently the E4200, and they all work fine down stream of the Cisco and with guest access, but I'd like to keep it all apple and use time control limits for my kids iPads etc but E4200 limits this to 5 devices.
It seems strange that apple is the only brand that can't do this?

Advice on set up for a mixed Airport network with guest network.

Hi,
The manuals on the Airport Extreme and Airport Networking are more technical than my knowledge base can follow. I would like advice on how to set up a new network with a mixture of wired and wireless devices and some Windows equipment as well as os x based macs. the following: dsl broadband from Talk Talk to be managed by a Draytek Vigor 120 external modem connected to an Airport Extreme. I want to connect a Nov 2009 iMac (with Mountain Lion installed), Apple TV and xbox by ethernet cable to the 3 ethernet ports on the Extreme, but also to connect wirelessly one Windows 7 laptop, one Macbook Pro (2010) (again running Mountain Lion) and various other wireless devices like an iPad 2, iPhones etcetera, with all devices being part of one network run under one SSID and able to access the internet, and the 3 computers being able to fileshare with each other. On my current Windows created network which I am abandoning for reasons I won't go into here, if more than one of the computers is switched on, I can use any one of the computers to access information in any of the shared folders on the other computers - via Finder in the case of the macs - and I need this going forward. I would also like to create a Guest network as I have a lot of people come to stay who need internet access. To further complicate things, I would also like to add in an Airport Express wirelessly onto the network and link that to a hi-fi to give me the ability to play my iTunes library (situated on my iMac at present) on the hi-fi.
I appreciate that there are similar questions but I have not really found an answer that exactly nails my situation.
Thanks in advance.

It is not really an issue of how many clients can the iMac serve, but more about the volume of traffic you are processing or data the database application needs to serve. We have a Mac hardware that is a good 6 years or more old running OSX Server and supporting 20/30 clients without any problems.
One idea you may like to consider.
Don't run the VPN on the mac, get a router or separate dedicated networking box that provides that purpose. Then it will talk the load of any networking issues and external attacks. It can also provide other networking services for you such a DHCP, firewall, DNS, internet gateway, etc. They cost less next to nothing and are easy to install.
When you need to get something faster, look for a second hand xerve - we use them all the time. They have the advantage of have fast and very reliable discs, also you can raid the disks and hot swap them for backup purposes,
Finally, moving from one machine to another is each with things like carbon copy. But you cannot have the same licence for OSX server running twice, so you will need to install normal OSX on the iMac once you have done the move.
As for can you easily move from a imac to mac pro, sure not to hard to do.

WRT1900AC Guest Network connection time limit

I think this is a fresh topic.
I have searched for this, but can't find any prior topics.
I upgraded from a Cisco branded E4200 (v1) to a Linksys WRT1900AC.
I have noticed that the guest network for the 1900AC kicks devices off after a period of time I have not managed to determine, despite them not being disconnected from the network. The device will simply tell me that a hotspot is detected and asks me to sign in. I have to open the browser and enter the password again. This is particularly annoying for work devices on the guest network that use VPN, as I have to get that running as well.
The E4200 I had before kept guests connected as long as they were on the network; only disconnecting them or taking them out of range for more than a day required me to supply the password again.
Is this expected behaviour? I'd prefer not to be repeatedly challenged for the guest password for devices that remain connected, just like I could with the E4200.
I use the 5GHz network for all my permanently connected devices ( a mixture of fixed and dynamic IP's) and leave guests and my work devices to the guest network on 2.4GHz (all dynamic IP's). I have things spaced out well in my home as I had run into issues with interference caused to my Sonos system, which I have eliminated by moving my 2.4GHz connected equipment. The physical layout is the same from when I had my E4200 and my 1900AC, so I'm confident it isn't a physical issue.
My 2.4GHz network has its SSID hidden to discourage people from using it.

How many total guests allowed did you set on your router? Make sure that the total number of devices connecting to the Guest network would match the total guests allowed.

I cannot add a Wi-Fi guest network. Gone to Utilities Airport Utilities and all get is an image/browser of my Airport Extreme. Looking for the browser which has the title Wireless but cannot find anywhere. I need help?

I cannot add a Wi-Fi guest network. Gone to Utilities>Airport Utilities and all I get is an image/browser of my Airport Extreme. Looking for the browser window which has the title Wireless but cannot find anywhere. What am I doing wrong?

Open AirPort Utility. The first screen looks something like this:
Click on the AirPort Extreme and another screen will appear. Click Edit, then the window with the Wireless tab will appear.
If you do not see these screens, you will need to start over and configure your AirPort again.

Airport Extreme 802.11AC + 5th Gen and guest network access

I have the current gen Airport Extreme 802.11AC with a 5th Gen extending the network. With this setup, I am unable to login using our guest network setup. I have tried using guest network with a password and one without but its the same results. When a guest logins, it stuck attempting to login with no error messages.
So is it possible to have this configuration and still have guest network access?

Please review what I said originally.......that the guest network function on the AirPort Extreme is designed to work with a simple modem......so the AirPort acts as the main router for the network..
Another way of saying the same thing is that the AirPort needs to be "in charge" of your network for the guest feature to work correctly. The AirPort cannot be in charge if it is connected to another device that is already configured to be the main router on your network.....your Actiontec modem/router.
The Actiontec device combines the functions of a separate modem and a separate router in one package. This type of device is known as a modem/router, or also known as a gateway.
Some folks call a modem/router or a gateway......a modem. So, things can get confusing.
I do not know if it is possible for the Actiontec device that you have to be configured to act as a simple modem.....so the routing functions of the device are completely turned off. (Turning off the wireless on the Actiotec does not turn off the routing function).
If you turn off the wireless on the Actionec, it becomes a modem and a wired router. And that wired router is still in charge of your network.
The guest network feature will not work correctly unless the AirPort is in charge of your network.
My suggestion was for you to ask your Internet Service Provider (ISP), if they could supply you with a simple modem. That is all that you need. You don't need two routers....and the Actiontec that you have now is not allowing the guest feature to work correctly.

Cascading EA4500s and Guest Network access

Hi, I hope esomone can help me here. I've got two EA4500 routers connected via ethernet. The primary router has DHCP enabled and the secondary has it disabled. IP address of primary is 192.168.1.1 and the secondary is 192.168.1.2.
I have set up guest access on both routers however only the primary router allows users to connect. When out of range of the primary router but in range of the secondary router the network is visible but when you try to connect to it, it only gives limited or no connectivity message and can't connect to the internet.
Is it possible for the guest network access to follow the same pattern as the secure network, i.e. the same network throughout the house?
Regards
Jon

Cascading two routers should have correct parameters set. For instance, the Ethernet port of the secondary router should be connected to the ethernet port of the primary one, and the DHCP should be disabled on the second router. The ip address you've set are correct for the both routers. This thing shoud be done if the connection is LAN to LAN.
By the way there are two types of cascading: Click here for info!
For the Guest Network:
Guest Network would only work if the the DHCP is enabled on your router. It means to say that on the type of setup you're doing which is LAN to LAN (DHCP disabled on the second router), Guest network would not work on the secondary router. If the connection is LAN to WAN, then both of the router should have Guest Network working.

How do I configure Guest network to access ethernet wired printer?

I have a wired/wireless network with a new dual band AEBS. The AEBS is connected to a Cisco router, which in turn sends it's connections to various wall-plates in our home. One HP 4110 printer is wired via it's ethernet port, one Mac Mini (OS 10.6.2) is hard wired also. The dual band AEBS 5 GHz network is used for our newer laptops, and the 2.4 GHz network is used for a G3 Firewire PowerBook (now don't make fun... it was the best there was at one time) running OS 10.4.11.
The PowerBook cannot access the printer that is hard wired via ethernet cable to the network. How do I get the PowerBook on the "Guest" network to access the printer?
I tried searching these discussions, but can't find an answer to my specific issue. Any help is appreciated.

Since you have a simultaneous dual-band AEBS, why not connect your PowerBook G3 to the non-Guest 2.4 GHz network created?
Can I take an AEBS that is a couple of years older (I have a couple of the flying saucers around here somewhere), wire that to an available ethernet port on the LAN, and then connect the older PowerBook G3 to that older AEBS wirelessly?
Sure
If so, will that arrangement slow down the entire system?
No
If that won't work, and I connect the PowerBook G3 directly to an ethernet port, will that slow down the other wireless computers?
Yes you can connect your PowerBook G3 via Ethernet. That would have no effect on the wireless computers.

How do I add a guest network to existing airport extreme configuration?

I have an existing Airport Extreme configuation in my home Wifi network and I want to add a guest access point. When I open the recently updated airport utilities, the screen no longer looks the way it used to, with the side bar on the left and my devices listed there for me to select (I also have an Airport Express). I used to be able to select the Airport Extreme from the left side bar, then hit continue to change any settings. Well now, since it updated, the screen looks different, with internet at the top, pointing to the Airport Extreme, then the Airport Express. When I select the Airport Extreme, it no longer gives me the option to change the settings for it, which is where my problem lies! Any help? I know it's probably something very simple that I am missing, but I'm at a loss.

Why would I download a lower version of AirPort Utility?
To gain more functionality.....since AirPort Utility 6.0 is otherwise known as "AirPort Utility Lite" on the forums. It's a "first try" for Apple with a new look. While it does look nice, it has been downgraded as far as the features are concerned.
For example, if you open AirPort Utility 5.6 and click on the AirPort Extreme on the left, your Generation version will be displayed on the right side of the page. There are many more advanced settings available in AirPort Utility 5.6 as well...that are not available on 6.0.
But, you don't have to install AirPort Utility 5.6 if you don't want to. I suggested it because it offers more features and will also look exactly the same as the AirPort Utility that you have used previously.
If your AirPort Extreme is in Bridge Mode, this indicates that you have another device...probably a modem/router....which is acting as the main router on your network. Bridge Mode is the correct setting for the AirPort Extreme in this case.
If you can post back with the make and model number of your "modem", we can check to confirm.
Unfortunately, the Guest Network cannot be enabled unless you configure the AirPort Extreme to be the "main" router on your network, which is likely not possible. If you try to configure the AirPort Exteme otherwise, you will receive error messages and the network will not function correctly.

How do to set up time limits on a guest network

I have a new generation Airport Time Capsule and I have set up a Guest Network for my kids but I would like to set up time limits on the Guest Network also, is there a way to do it?

It is not possible to set up specific time limits for the Guest Network as a whole, but it is possible to set up individual time limits for each device that will be connecting to the Guest Network.....and, also the main network for that matter.
If you can provide us with some more specifics on what you are trying to accomplish, how many devices will be involved, etc.......that will help us craft our answer to provide accurate information.
Meanwhile, if you want to take a look at the general settings in Timed Access....
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the Time Capsule icon, then click Edit
Click the Network tab at the top of the screen
Enter a check mark in the box next to Enable Timed Access
Click on the Timed Access button
Click Cancel to avoid making any changes to your current setup

Hi. Does anyone know how to delete my guest network from the list of network choices that everyone in the neighborhood sees when picking a network? Followed helpful suggestions on this site to delete the netwk but it still appears. Appreciate any help!

Hi. I'm trying to make my guest network disappear from the list of network choices that appears to everyone in the neighborhood. Even though I followed the great suggestions on how to delete the network, it's still appearing in the list that everyone sees. It has my name and would prefer to get rid of it.
Please help! Many thanks!

Thank you for not only the tip but also especially the research showing that for anybody other that those using Wi-Fi for the first time the network wouldn't disappear. I wanted it to disappear for everyone so.....I finally solved it by resetting the Airport Extreme to the factory settings and starting over from scratch! It worked! Yay!!!!!
So, for everyone that has had this problem (and I've read many of the same complaints in different places on the Internet), you must go into Airport Utility and check the box stating that you want to reset it to the factory settings. Do not do it with a paper clip and the reset button on the box; I tried that first and it did not work. You must reset it via the Airport Utility. Then just start over and you will have the choice to NOT check the box to Enable Guests. If you want to enable guests, just be sure not to use your name or you're back to the same problem. Apple is so great with everything...wouldn't it have been so easy for them to just put this in the manual somewhere????? Thanks for all your help. Hope this helps others!

How can I delete the guest network from my airport. It was fine until the last update. It says my whole name's guest network which I do not want everyone seeing. There is no guest network setting in my airport utility.

How can I delete the guest network from my airport. It was not showing up until I recently upgraded the airport. It now says my name's guest network and I don't like my name showing on the available network list! I am using a Verizon wireless modem with the wireless feature off.

Open AirPort Utility, go to the Wireless tab and remove the check from the guest network check box.

How can I create a guest network on an airport extreme that connects wirelessly with a Timecapsule

I have a Timecapsule in one place of our house, that is connected to Internet. I need to extend the range of my network: 1. my private network needs to get to a remote location to make connection with speakers (Itunes). for this I need to first extend the range of my private network, because the speakers are too far away from the TC. 2. I need to set up a guest network, but at quite some distance from my TC, in an other part of the house, too far away from the TC (so a guest network on the TC won't do).
For this, upon advice from an apple store, I bought an airport extreme, which I have placed on a location where it can connect to the TC, to extend the private network. On the location of the speakers, I have an aiport express (connecting to the extreme), to play music from Itunes. The setup at this moment is: TC makes connection to internet, and broadcasts a private network. Extreme connects to this private network, and broadcasts it further to the Airport express, that captures it and plays the music. I would now like to create a guest network on the Airport Extreme, while this Extreme keeps on connecting to the private network of the TC and keeps on broadcasting it to the Express. Is this possible? How can I do this? Thanks for the help !

I would now like to create a guest network on the Airport Extreme, while this Extreme keeps on connecting to the private network of the TC and keeps on broadcasting it to the Express. Is this possible?
Unfortunately, the "main" router...your TC in this case....is the only device that can create a Guest Network, assuming that the TC is connected to a simple modem.
Unfortunately again, the Guest Network cannot be extended. Your only real option here is to create a Guest Network on the TC and hope that it will have sufficient coverage for your needs.

"Guest Network" VPN

Similar Messages

Maybe you are looking for