How can i delay the present of direct connected route?

Hi, I got 2 3550SMI switch interconnecting by Etherchannel. Each 3550 has an uplink to its upstream router (R1-SW1=SW2-R2). R1 and R2 connects to the remote site routers (say R3 and R4).
With EIGRP redistribute connected, R1 update the direct connected network via WAN link A to R3 where R2 does the same thing updating R4 via WAN link B.
The failover is fine after SW2 powered off. However, problem occured when I powered up SW2. During the bootup of SW2, there was carrier signal which brought up the ethernet port of R2 and the direct connected route presented in R2 then updating R4. Some of the traffic had started to come over from R4 via WAN link B to R2 while SW2 is still booting. (or Etherchannel was not yet ready). As a result, workstation connecting to SW1 cannot be reached for those traffic came from R4->R3->SW2.
I have tried to use "carrier-delay 60"on the ethernet port of R2. It seems solve the problem since the direct connected route delay 60sec. Within that 60 sec, no update via EIGRP from R2 to R4 so that all traffic still went through R3->R1. After that 60 sec, SW2 had already bootup and the etherchannel was also ready.
However, i can only do it with C3725 router. I've tried 1750, 25xx, 26xx and 3640-12.3T but the behavior was not expected (route still present immediately after carrier signal detected).
My questions are:
Is that command valid on Eth or FE interface?
Is there any different using that command with diff. router series, eg. ISR (18xx,28xx,38xx)?
Is there any condition that I could make it work? (at least 3725 worked)
Is there any other way to delay the present of that direct connected route?
Thanks.

Hello,
instead of the 'carrier-delay' command, you could try to change the EIGRP hello and hold-time intervals (which default to 5 and 15 seconds respectively on broadcast media such as Ethernet), in order to delay EIGRP convergence. So, on your Ethernet interfaces when you use the interface commands:
ip hello-time eigrp x 60
ip hold-time eigrp x 180
the redistributed routes will show up only after 60 seconds, which effectively does the same as the 'carrier-delay'...
Can you try that and see if that works for you ?
Regards,
GP

Similar Messages

How can I control PPT or another?? (How can I be the presenter)

Hi, this is Daniel.
we always have meeting with Lync.
we got link from buyer and when we click, we connected with "Lync web App"
but we only go into as a "guest"
And we cannot be the presenter.
so we bought license for "lync online(plan 2) 1 license"
now we have "domain" ; WontaeDiecastingCoLtd.onmicrosoft.com
we can log-in but we still can go into as a only "guest"
How can we be the presenter??
Please let me know about that.
Thank you.
OS : Windows XP
Explorer : 8
Office : 2007

Hi Daniel,
If you’re the Lync meeting organizer, you’re already as a presenter.
If you’re not the Lync meeting organizer, you can ask the organizer to promote you as a presenter at
any time during the meeting by right-clicking on your name and selecting “Make a Presenter” as shown here:
For more details,
http://blog.insidelync.com/2014/03/allowing-anonymous-presenters-in-a-lync-meeting/
Note: Microsoft is providing this information as a convenience to you. The sites are not controlled by Microsoft. Microsoft cannot make any representations
regarding the quality, safety, or suitability of any software or information found there. Please make sure that you completely understand the risk before retrieving any suggestions from the above link.
Best regards,
Eric

I am using a 5s under IOS 7.1.1. How can I change the year field directly when editing an existing calendar entry?

I am using a 5s under IOS 7.1.1. How can I change the year field directly when editing an existing calendar entry?

Glad that helped.
Enjoy your iPhone!

How can I delete the history of wireless connections? Need to delete it entirely, as I have a new airport extreme and I named the network the same as it had previously been,

How can I delete the history of wireless connections? I got a new apple extreme, and I kept that same network name as I previously had with the LinkSys. Now the Mac won't automatically connect to the network. Genious Bar fixed my Pro, they said that you have to delete all the history, not just the network name. I wasn't at the Genious Bar to see how they did it, now I need to fix the Mac. Appreciate any help!

Yes, so...
I have also closed iTunes, reset network settings on the iPad, then shut down and restarted the iPad. Still, I end up with greyed out rectangular icons for all the movies I've ever streamed from my Mac Mini to my ipad via my home wireless router.
Again, I have watched all the way to the end of the movie, selcted the movie in iTunes and chosen "mark as watched", and then deleted it in ITunes.
Any ideas?

How can i delay the using period of certificate when i start ssl in ims

i enabled https and imaps in ims52,but i found the period of validity of the certificate is 1 year by default. how can i delay it to 5 years or more?
does it specify during generation of CERTIFICATE REQUEST ?
thx!
Message was edited by:
giant.sala

There is nothing you can do in Messaging Server for this. The expiration of a certificate is defined by the certificate itself.

How can I modify the presentation file ( *.ser ) using external tools ?

Hi All,
When build, the presentation will be saved as "*.ser" files. How can i edit them using some external (not within the ALBPM5.7 studio) tools for decoration?
thanks a lot
Jack

As long back as I can recall Adobe has always used the UNC-path for it's links.
At least back to CS2. Before that and my memory is a bit blurred.
We ourselves are using CS3/CS4, with UNC-paths, on 300+ clients without any problems at all.
Their drives are mapped to a drive-letter, but InDesign still resolves the UNC-path. This has works flawlessly so far.
When we experience issues that related to our network then it's usually something else that is to blame.
So far embedded images and IP-phones and been the major culprits.
But I'm not a network-savvy at all so don't take my words for it.

How can i display the presentation variable in my reports

Was facing a problem to display the Presentation variable on my report, however i managed to display it on answers, but when i try to display it on my Publisher report it doesnt shows any data.
I use to Select the Values From my prompt, and it shows the Reflection of Presentation Variable on my Answers Report. but i cannot see the Reflection of data on my Publisher Report Please any One Can help me with this.

Removing '' does not work it given the following error
"State: HY000. Code: 10058. [NQODBC] [SQL_STATE: HY000] [nQSError: 10058] A general error has occurred. [nQSError: 27002] Near <@>: Syntax error [nQSError: 26012] . (HY000)"
and by adding space you mean that I use it as '@{ BbranchCode}'?
What I am doing at the moment is
1. Write the given query in oracle BI Answers.
2. Made a dashboard prompt in Answers.
3. Made a report in dashboard using the Answers report and the dashboard prompt.
Up till this step it works perfectly fine and the data displayed in manipulated on the basis of the values selected in the prompt.
4. Now what I want is to display this report in Dashboards using oracle BI publisher. For that I use the template builder provided for microsoft word.
5. I login to that add-on, open the answers report where I can see the field in the rowset. I select that field and save the template.
6. I open the oracle BI publisher and make a new reprt with data model of the answer's report and Layout of the one I just created.
7. I open the dashboard and put in the BI publisher report in the same page in which the asnwers report and the prompt was.
8. Upon changing the values of the prompt the report in the answers is still getting manipulated but I am not able to see its reflection of the BI publisher report.
The thing is that I am currently using this presentation variable to manipulate my reports in dashbords using dashboard prompts. The report is built in oracle BI Answers and it is working perfectly fine with it. Now when I use the template builder for Microsoft Word and open the template with the answers's report of this query I see the field in the row set but when I display the template in the dason the bases of this presentation variable the report in the oracle BI Answers is getting updated when I change values but when I use the template builder for microsoft word the the field is being shown in the row set.

How can i check the devices which are connected with my AirPort Express?

I saw an unknown device in the app 'Who Uses My Wifi?', how can i check it through AirPort Utility and can i remove this device by the app?

Open AirPort Utility
Hold down the option key on your Mac while you double click the picture of the AirPort router
Currently connected wireless ciients will be displayed
Don't forget about the wireless printer you might have, baby monitor, wireless thermostat and other items that connect using wireless. They will appear on your check.....not just computers or iPhones, etc.
If you have 3 wireless devices, and you see 4 devices connected, you may have an unwanted guest.
If you are using good wireless security, like WPA2 Personal, and a good password, it is extremely unlikely that another device will be on your network

How can i delay the line and charactor rate of my serial port transmision?

In hyperterminal I can pick the line and charactor rate , but I can't seem to slow down the rate when using the serial port by itself.
Attachments:
remod_chan_4.txt ‏1 KB
serial_INT_chan3.vi ‏31 KB
read_text_file.vi ‏20 KB

There's nothing built into the VISA or old serial functions but it's pretty simple to program yourself. Here's a VI for specifying a delay between characters. It uses VISA but you can easily swap that out with the old serial write if you want. It just breaks out the text string character by character and adds a delay before each character is written. To add a line delay, just add another delay after the entire string is written.
Attachments:
Serial_Write_With_InterCharacter_Delay.vi ‏45 KB

Hi! How can I change the header text direction to vertical?

I have many columns with big names, but I need small space for body cells, and I want to check all the table at a view ... So I want to change the direction of the header texts to "left vertical" or "right vertical".

There are a couple discussion threads on this already. Fundamentally it is not a feature that Numbers supports. There are several work arounds but non of theeem are great:
Please see this thread:
https://discussions.apple.com/message/15240103#15240103

How can I change the sorting direction of Events in Photos?

How can I change the date Sort "direction" in Photos for the iPhoto Events folder? Unlike iPhoto, which sorted the older photos at the top, Photos does the reverse. Can this be modified?

>System Preferences>Hardware>Mouse>Point & Click>Scroll Direction.

How can I change the order in which photos are presented on an Apple TV?

I am showing photos on my Apple TV via my Apple MacBook, iTunes and Home Sharing.
That all works nicely for me, except that I wish to change the order in which a few photos
are being presented. How can I change the presentation order on the Apple TV?

Welcome to the Apple community.
You'll need to change the order in iPhoto. Open the album you wish to re-order, manually sort them to the order you want, then use the time and date and batch change options as applicable from the photos menu to retag your photos.

I accidentally erased my ipod touch how can i restore the home page, i accidentally erased my ipod touch how can i restore the home page

i accidentally erased my i pod touch how can i restore the home page ?

Connect the IPod to yur computer and restore via iTunes on the computer. For how to restore see:
iTunes: Backing up, updating, and restoring your iPhone, iPad, or iPod touch software
How did you erase the iPod?
What do you mean by restore the home page?

I down loaded sygic on my iPhone 3s but the icon is missing even in the search but when I want to download it again ,it say this application is present, how can I make the icon to show up

I down loaded sygic on my iPhone 3s but the icon is missing even in the search but when I want to download it again ,it say this application is present, how can I make the icon to show up

- Have you tried a reset. Nothing is lost
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Try syncing the iPod to your computer. Then delete from iTunes and sync. that should delete it from the iPod. Then redownload it.

I have a keynote presentation that includes a significant amount of video. When I edit the keynote slides (not the video slides) how can I save the changes without re-saving the videos (because that takes a VERY long time)?

I have a keynote presentation that includes a significant amount of video. When I edit the keynote slides (not the video slides) how can I save the changes without re-saving the videos (because that takes a VERY long time)? I edit the presentation depending on the audience to which I am presenting.

If you add a new slide with just a text box (therefore a very small amount of data), to an existing presentation then save, Keynote will only save the new content to the file, it wont save pre-existing content as its already included in the file.
The time taken to "save" will be very much shorter than a "save as" when all of the existing content is saved again.

How can i delay the present of direct connected route?

Similar Messages

Maybe you are looking for