How can i prioritize PBX over Router? (PBX and Router plug directly into Modem)

Hello everyone,
I work for a small ISP and i just got hired here a couple months ago. I've been tasked to figure out a solution to this problem. We have customers that have a network, and they also have a phone system. Both devices (router and PBX box) have a static IP address and plug directly into the modem. The issue we see is that the internal network is hogging the bandwidth and this kills the phone systems quality. What i tried was putting a 2960 in between the modem and router/PBX system. Then rate limiting the port to the internal network but it doesn't work out so well. I have it set to use 8mb/800bk. Which should dedicate 2mb/200kb for their phone system at all times. But when i do speed tests i get 2mb down and 200kb up. My download speeds are not right, yet when i do a "no mls qos" the download goes to the 8mb i have set, but then my upload doesnt work correctly. Does anyone have an idea to fix this? Or any better ideas? 
no aaa new-model
system mtu routing 1500
ip domain-name XXXXX.com
mls qos
spanning-tree mode pvst
spanning-tree extend system-id
vlan internal allocation policy ascending
ip tftp source-interface Vlan1
class-map match-all RATE_LIMIT_CLASS
  match access-group name RATE_LIMIT_ACL
policy-map RATE_LIMIT_POLICY
 class RATE_LIMIT_CLASS
  police 800000 8000 exceed-action drop
interface FastEthernet0/1
 description Internal Network
 speed 10
 duplex full
 srr-queue bandwidth limit 80
 service-policy input RATE_LIMIT_POLICY
interface FastEthernet0/2
description PBX Box
ip http server
ip http secure-server
ip access-list extended RATE_LIMIT_ACL
 permit ip any any
access-list 50 permit X.X.X.X 0.0.2.255
line con 0
 logging synchronous
line vty 0 4
 access-class 50 in
 logging synchronous
 login local
line vty 5 15
 access-class 50 in
 logging synchronous
 login local
end

Heres an update, even with the Router plugged into fa0/1 with the following config, it still only gets 2.5mb down. Ideas? Could it be because the ports on 10mb?
interface FastEthernet0/1
 description Internal Network
 speed 10
 duplex full

Similar Messages

  • My iphone5s is dead...plugged it into computer to charge, and it says "internal device error" how can i fix....i already tried plugging it into all other ports

    my iphone5s is dead...plugged it into computer to charge, and it says "internal device error" how can i fix....i already tried plugging it into all other ports

    tried another computer?
    if it works there then your itunes install have gotten defect

  • How do I limit access of a computer that is plugged directly into the router?

    I have an AirPort Extreme, Version 7.6.1  I need to limit access of a computer that's plugged by usb directly into the router.  I have the MAC address for this computer and have had restrictions on it the in the past, but it was connected by WiFi then.  How do I do this?  Do I limit access to the Ethernet ID?  I don't want to lock myself out trying to figure it out; I did that last night.  Can someone advise please.

    You could use OpenDNS's parental controls:
    http://www.opendns.com/home-solutions/parental-controls
    It can restrict access according to your specifications for everyone on your network.
    It's free.

  • How can I restore the web address page and not be directed to a search engine?

    My address bar has disappeared. Whenever I want a new address and type it in I am diverted to a search engine which locates the address I have typed in. I cannot get to the preferences bar to make corrections.
    I use Windows 8. All was fine until a few weeks ago when something changed my Firefox system.

    Make sure that toolbars like the "Navigation Toolbar" and the "Bookmarks Toolbar" are visible.
    *Firefox menu button > Options
    *View > Toolbars (press F10 to display the menu bar)
    *Right-click empty toolbar area
    Use Toolbar Layout (Customize) to open the Customize window and set which toolbar items to display.
    *check that "Bookmarks Toolbar items" is on the Bookmarks Toolbar
    *if "Bookmarks Toolbar items" is not on the Bookmarks Toolbar then drag it back from the toolbar palette into the Customize window to the Bookmarks Toolbar
    *if missing items are in the toolbar palette then drag them back from the Customize window on the toolbar
    *if you do not see an item on a toolbar and in the toolbar palette then click the "Restore Default Set" button to restore the default toolbar setup
    *https://support.mozilla.org/kb/How+to+customize+the+toolbar
    *https://support.mozilla.org/kb/Back+and+forward+or+other+toolbar+items+are+missing
    You can check for problems caused by a corrupted localstore.rdf file if the above didn't help.
    *http://kb.mozillazine.org/Corrupt_localstore.rdf

  • How can I import all the music files on my computer directly into my iTunes library?

    I recently cleaned my computer of all junk files and this resulted in a loss of all my music from my iTunes library. All of the files are still on my computer but I can only find them one at a time is there a way to speed up this process?

    Ok, go to your downloads in itunes and right click on what you wish to remove and click delete, then confirm the dialoague box and it should remove it.  I did this with a free tv episode to test it out.  Just now worked.  If you have problems try updating itunes and then try again.

  • Can I play a podcast (in Safari) and record it directly into GB or iTunes?

    Have several podcasts which I'd like to burn cd's of and I don't know if this is possible. Need to know the settings in Garage Band to do this if possible. Then can I burn a cd from GB, or would I have to Share it to iTunes first, then burn the cd? My GB is 08. Thanks for any help. pdm

    Thanks HangTime. I didn't move the file from the web page into iTunes. I right clicked and downloaded it to the desktop. Then I dragged it from the desktop into Garage Band, made splits between the songs and the talking, deleted the talking and joined the songs. It worked fine. Thanks again. pdm

  • How can i use a second router to replace verizon fios router?

    Okay so just as the title says how do i use a second router? I got a cisco valet router... I don't know how to use it because the verizon router/modem is wierd i know how to use a router if i only had a modem but fios gives router/modem so how can i use my 2nd router? The current verizon fios router/modem is b/g mode and i wanna change to b/g/n so i can get a better speed from my internet... SO how can i use my 2nd router? I tried this http://www.dslreports.com/faq/verizonfios/3.0_Networking#12506 but i don't get it can someone guide me better or make a video explaination on how to use a 2nd router? I have it connected with see as in pic i connect from my router Internet port to wan port and the ethernet lan port to the ethernet lan port on verizon fios and no work please help...

    OK, so with this, we have a few options. You appear to have a MoCa connection to the ONT, hence the coaxial cable being present.
    1: The ActionTec can be bridged to the Valet router. This will not require any additional cabling, however it will require a small amount of work to have working. You will also require the ActionTec still in the mix, even though it will not be acting as a router anymore with this configuration.
    Visit http://www.dslreports.com/faq/16077 and look at Option 4. There is a thread linked that will allow you to set up the ActionTec as just a MoCa bridge, and will pass the Public IP to your router. You will, in order for this to work once the ActionTec is bridged, need to connect the cable from your Valet router's Internet port, to the ActionTec's LAN port and nothing else goes to the ActionTec. From this point, your Valet should run as your primary and everything should connect through your Valet. If you are adding another router, a Netgear N300, you should perform the LAN to LAN setup, which we will talk about once you've got the Valet working correctly. LAN to LAN configs require a custom setup, so do not set up the Netgear for now.
    2: This is my preferred method, which would be to run an Ethernet cable to the ONT. Option 6 in the FAQ. This will require spaking to Verizon to have them move your ONT to Ethernet, but once they do this, you can disconnect the Coaxial Cable from your ActionTec router, and plug in your CAT5/CAT6 cable from the ONT to the ActionTec's Internet/WAN port. Use the ActionTec to ensure everything is working after the switchover, and once off the phone, log into the ActionTec, perform a DHCP Release, and then prompty power off the ActionTec. Once this is done, plug the CAT6 cable into your Valet router's Internet port. You should from this point, be able to connect to the Cisco, and if the DHCP Lease was broken successfully, the Cisco should begin serving up your Internet connection. If it does not, leave the Cisco powered off for a few hours to break the DHCP lease, and then power it up. If the Valet does not work, still, give the Valet a factory reset and set up this router again, with the Ethernet cable from the ONT connected to it.
    I would just take a good luck at the FAQ linked above again, and see what would work the best. Easiest thing to do is to get the ONT moved to Ethernet, which allows you to eliminate the ActionTec unless you need it in the future for TV service, and also allows you to use any router with ease.
    Once the Valet is up and running and holds your Public IP address from Verizon (use http://whatismyip.com/ to determine this) , and also serves up IPs to devices on your network, post back and we can help you set up the Netgear. If you have any issues while setting this up, fall back to the ActionTec. It's factory reset will work without configuration needed, regardless of you being on Coax or Ethernet.
    ========
    The first to bring me 1Gbps Fiber for $30/m wins!

  • My ipad has gone in lost mode by mistake and now i have it and i enter the password and i cant enter my ipad how can i enter or restart the ipad and start back over new

    my ipad has gone in lost mode by mistake and now i have it and i enter the password and i cant enter my ipad how can i enter or restart the ipad and start back over new

    FORCE IPAD INTO RECOVERY MODE
    1. Turn off iPad
    2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
    3. Plug USB cable into computer's USB port
    4. Hold Home button down and plug the other end of cable into docking port.
    DO NOT RELEASE BUTTON until you see picture of iTunes and plug
    5. Release Home button.
    ON COMPUTER
    6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
    7. Select "Restore iPad"...
    Note:
    1. Data will be lost if you do not have backup
    2. You must follow step 1 to step 4 VERY CLOSELY.
    3. Repeat the process if necessary.

  • I had iMessage with a UK number and I have moved to Australia and want to use an Australian number, how can I change it over?

    I had iMessage with a UK number and I have moved to Australia and want to use an Australian number, how can I change it over?

    something here may help
    http://support.apple.com/kb/TS4268

  • Airport extreme software will not install on vista, how can i still configure the router?

    airport extreme software will not install on vista, how can i still configure the router?  Trying to help someone with vista get an airpot extreme configured.  10.0.1.1 does not work, the software will not install correctly on their vista machine.  How can I get into the base tation and lock it down?

    Hi - Vista can be tricky - I need more info to see if I can be of some help - first, is the Vista machine a desktop or a laptop and is it fully up to date with Windows Update (sp2 or higher)? - next, are you trying to install Airport Utility version 5.5.3 which is the correct one for Vista? - and finally, what do you mean "it will not install" - what kind of error messages or evidence are you getting?

  • I have several albums in my library that I cannot get onto my device. I have tried manually adding the albums, but it doesn't work. I can view the albums in "Music," but when I click on "iPhone" they are gone. How can I transfer them over?

    Can't add albums in library to iPhone.

    Full question: I have several albums in my library that I cannot get onto my device. I have tried manually adding the albums, but it doesn't work. I can view the albums in "Music," but when I click on "iPhone" they are gone. How can I transfer them over?

  • I installed an airport card in my powermac g4, how do I connect to my router (not an airport base.) How can I connect to my router?

    I have a powermac g4 quicksilver in which I have installed a normal airport wireless card in the dedicated slot. How can I connect to my router? It is not an apple airbase station but does it need to be? How can I connect to my router?

    What encryption is the Rouer using? If WPA2 you likely can't.
    Go to System Preferences
    Click Network
    Highlight AirPort and click Configure...
    What shows for Routers there? Or is Join Other Network availabe in 10.3.x?

  • How can i completley wipe my iTunes library and start over?

    I messed up my library and by mistake re-named many songs with one title.. also have many 2x or 3x songs.. my itunes is a mess!
    How can i completely erase all the songs and start with a new itunes (and then i'll download my past purchases and my files and so on...). I have the latest version of itunes.
    Thank you in advance!

    Delete the entire /Music/iTunes/ folder.
    Make sure you have a backup of all your media files (the /Music/iTunes/iTunes media/ folder).

  • How can I use LCCS with ActionScript 3 and Flash CS4?

    Hi,
    Using Stratus I was able to create an an application using Action Script 3 and Flash CS4.  The sample code on the Adobe site was quite straight forward and easy to understand.  I now want to switch over to  LCCS but can't find anything any where on how to use Action Script 3 and Flash CS4 with LCCS.  Do I need to know Flex to be able to use LCCS?  Everything was quite simple and easy to understand with Stratus and makes complete sense.  But LCCS is really confusing.  Is there any sample code on how to establish a connection in Action Script 3 and then stream from a webcam to a client.  There is nothing in the  LCCS SDK that covers Flash and Action Script 3.  Please help!  I found the link below on some forum but it takes me nowhere.
    http://www.adobe.com/cfusion/webforums/forum/messageview.cfm?forumid=72&catid=75 9&threadid=1407833&enterthread=y

    Thanks Arun!
    Date: Thu, 29 Apr 2010 11:44:10 -0600
    From: [email protected]
    To: [email protected]
    Subject: How can I use LCCS with ActionScript 3 and Flash CS4?
    Hi,
    Welcome to the LCCS world.
    Please refer to the SDK's sampleApps folder. There would be an app called FlashUserList. The app demonstrates how LCCS can be used with Flash CS4. Its a  pretty basic app, but should help you moving.
    We are trying to improve our efforts to help developers in understanding our samples. Please do let us know if we can add something that would help others.
    Thanks
    Arun
    >

  • How can I disable iCloud on my iMac and my iPod touch 5th gen?

    My ipod touch 5th gen now syncs through icloud. How can I disable icloud from my ipod and my imac and go back to syncing through iTunes.  Is it possible to do this without losing the data in contacts and ical?  Any ideas would be much appreciated!

    With the iPod connected to your computer go to the Summary pane for the iPod in iTunes and uncheck the box that says: Sync with this iPod over Wi-Fi.
    Also in the Summary pane check the box that says backup to the computer.

Maybe you are looking for