How do I change just the width or the height of a brush in CS4

I have a brush that is square.  Is it possible to change just the width or just the height and if so, how?

  Thanks so much.  Before I asked this question I searched and searched for what I knew was going to be an easy answer, but just couldn't find it.  Thank you for your quick and perfect answer.

Similar Messages

  • How to change the width of the whole portlet layout?

    Dear all,
    As we know, now the width of portlet layout has set to 100%. But there is a new requirment from my customer that the width of the whole portlet layout view must be set to 750px.
    So I tried to edit the css file and I found a block:
    #pt-portal-content-view
         margin-top: 0px;
         width: 100%;
    I tried to change the width to 750px, but nothing happened.
    I want to know the way to change the width, thank you all!
    Regards,
    finall
    OK,I have found the place to do it:
    .portalContent          {
         display: block;
         width: 750px;
    I set to 750px,then it works.:-)
    But another question, how to make the content align to the center? I tried a stupid method, add margin-left:
    .portalContent          {
         display: block;
         width: 750px;
         margin-left: 120px;
    In 1024 X 768, it's ok, but it don't work well in 800 X 600.
    When I set the all content width to 750px, I tried the three columns view, the portlet still run over the border.If there is any way to control this? thank u in advance!
    Regards,
    finall
    Edited by finall1980 at 02/01/2007 10:09 PM

    Try this:
    .portalContent {
    display: block;
    width: 750px;
    margin: auto; /* for properly-implemented browsers */
    text-align: center; /* for IE 6 */
    As for running over the 750px, there's nothing you can do about that other than actually narrowing the columns AND making sure that your portlet authors don't produce content that's too wide.
    Chris Bucchere | bdg | [email protected] | http://www.thebdgway.com

  • How do I change the width of the x-scrollbar for a waveform graph?

    I have a LV7.1 application that contains a waveform graph and must be usable on several PC with widely varying screen resolutions.  I have decided to position and scale the front panel objects programatically, including the graph itself.  The appearance of the graph is satisfactory on all screens, except for the x-scrollbar.  The width of the x-scrollbar does not change when I change the size of the graph.  I cannot figure out how to change the width of the scrollbar programatically to match the adjusted size of the graph.  Any suggestions?
    Regards,
    Chris

    Chris,
    I don't think that you can change the width of the x axis scroll bar programatically.  One thing you could do though is create your own scrollbar and change it's properties as your program runs.  I wrote a quick example of how you could do this and I've attached it to this thread.
    I hope this helps,
    Justin D.
    Applications Engineer
    National Instruments
    Attachments:
    ChangeXScrollbar.vi ‏116 KB

  • How do you change/adjust border width for all the cells in a table created in Pages?

    How do you change/adjust border width for all the cells in a table created in Pages?
    Note- I am trying to figure out how to create and format tables in the latest version of the Pages app on an iPad air (iOS 8.1.1.1) . Creating tables, adding or removing borders for individual/all cells in a table seems straight forward. However the default border style seems to be a heavy black line. How do I change this?
    I found the option add or remove borders for all/ individual cells in a table, however I can't find any option within style/format dialogue screens for changing colour or line thickness for table cells. Likewise I can't find any clear instructions on how to do this in apple help pages or support website
    Btw- I'm assuming  it is possible to customize/adjust the colour & thickness of selected lines in a table created in this app (it's fairly easy to do this word processing apps like MS Word) please let me  know if this is not actually possible in Pages

    They know perfectly well what they took out of Pages '09.
    Well over 90 features.
    Do you think you posting feedback is going to remind them of what they did?
    http://www.freeforum101.com/iworktipsntrick/viewforum.php?f=22&sid=3527487677f0c 6fa05b6297cd00f8eb9&mforum=iworktipsntrick
    Pages '09 should still be in your Applications/iWork folder.
    Archive/trash Pages 5 and rate/review it in the App Store, then get back to work.
    Peter

  • How to change the width of the field?

    Hi all,
    I would like to decrease the width of a field on my report.
    But I can't do it in the Property palette. I am not able to change the width property. The width of the database column is varchar2(255). I do not want to decrease the length of the database column, but only the width property of the field.
    Any ideas?
    Regards
    Leonid Pavlov

    You can't change that from where you are trying because that info is coming from the database. To resize the field just open the layout editor and size the field to the size you want.
    Thanks,
    Tom

  • How to change the width of the variable screen?

    Hi
    like in the subject mentioned i need to know how i can change the width of the variable screen....
    right now i have to scroll if i want to see the right part auf the variable screen...
    maybe i can change the width with css?

    Hi,
    Using CSS specify the table width for the variable screen and include the Css in the header section of the table.

  • How to change the width of the EditForm.aspx and NewForm.aspx for both new and edited list entries?

    How to change the form widths for the EditForm.aspx and NewForm.aspx files that display both new and edited list entries?

    Hi  ,
    According to your description, my understanding is that you want to modify the width of the New Form and Edit Form of a list in SharePoint 2010 .
    1.Go to your SharePoint site -> your list.
    2.In top ribbon click  List tab(List Tools).
    3.Towards right you will see option as Form Web Parts, click on it, the three forms will be listed there [New Form, Display Form, Edit Form].
    4.Select the one on which you want to increase the width/height.
    5.It will open in edit mode, click on Add a Web Part.
    6. Click on Forms [Categories] => HTML Form Web Part.
    7.After adding the HTML Form Web Part, click on Edit WebPart.
    8.Click on Source Editor, Remove all code from it and put an empty HTML table with width and height as per your requirement ex. to increase width
    <TABLE WIDTH="800px">
    <TR><TD></TD></TR>
    </TABLE>
    9.Save the form and check out your respective modal by clicking on the same in your list view.
    Reference:
    http://sharepoint.stackexchange.com/questions/40580/how-to-modify-width-of-standard-dialog-form-sharepoint-2010
    Best Regards,
    Eric
    Eric Tao
    TechNet Community Support

  • How to change the width of the bar of bar charts?

    Hi,
    I am using Crystal Reports 11.
    I created some stacked bar charts. Now, I want to change the width of the bar. Some one told me that I can't do that because it's totally controlled internally by Crystal Reports.
    Really?
    If could, how could I do?
    Thank you in advance.

    Hi,
    The only way you can set the width of the bar is by going to Chart Options (Right-click Chart in Preview Mode > Chart Options > Appearance tab > Decrease the Gap Width).
    Hope this helps!
    -Abhilash

  • How to change the width of the scrollbar

    how to change the width of the scrollbar,
    I wanted to have a large scrollbar in all controls (for a touch screen app lets say) then is that possible?
    Either through CSS, code,
    skins anything really... Any ideas?
    Thanks in advance.

    Hi,
    horizonatal(vertical)ScrollBar.width - in AS/MXML code
    horizontal(vertical)ScrollBarStyleName - for style. But I'm not sure that width getted from css.

  • How to change the width of the auto complete drop down list?

    Hi,
    I implemented an autocomplete mechanism, using ICompletionSession and ICompletionSourceProvider. I have an issue with the size of the drop-down list opened when I use this autocomplete mechanism. The width of the autocomplete list remains the same, even
    if the strings displayed change. This is apparent especially when I hit "backspace" on the already typed string, while the drop down list is opened: the deletion of the last character allows for more completion strings to be used, but since the drop
    down width does not change, the longer strings appear cut.
    Is there a way to force the drop down list to recalculate its width?
    Yoel

    I don't think there's any way, even VS itself can't do that you know, and the interfaces don't have such kind of events or properties.

  • How can i fix the tab overlapping when i change the width of the url bar with #urlbar-container [focused]?

    I want to create for myself the most minimalistic browser experience as possible and i've put the most used features in the title bar. For purposes of space i had to fix the width of the url bar to a minimum and my intention is to increase it to a fixed width only when #urlbar-container [focused]. The problem is that #urlbar-container will overlap the existing tabs instead of shrinking their space, making it look really bad. It looks wonderful with #urlbar-container:hover, but i can't use that since whenever i want to refresh the wesbite using the button the width of the container will increase moving the button from the place i had the mouse in the first place to click it.
    Fixed width of the url bar when #urlbar-container is not focused:
    http://imagizer.imageshack.us/v2/800x600q90/829/xo4o.png
    Fixed width of the url bar when #urlbar-container [focused]:
    http://imagizer.imageshack.us/v2/800x600q90/34/8o36.png
    This is the css i have for the url bar at the moment:
    <pre><nowiki>#urlbar-container {max-width:225px!important;}
    #urlbar-container {min-width:225px!important;}
    #urlbar-container {transition:0.7s!important;}
    #urlbar-container [focused] {max-width:500px!important;}
    #urlbar-container [focused] {min-width:500px!important;}
    #urlbar-container {transition:0.7s!important;}
    #urlbar {border-top-right-radius:10px!important}
    #urlbar {border-bottom-right-radius:10px!important}</nowiki></pre>

    What method (code) did you use to get the Tab bar displaying in the space used for the Navigation Toolbar (location bar)?
    The Tab bar should be displayed above the Navigation Toolbar.
    Start Firefox in <u>[[Safe Mode|Safe Mode]]</u> to check if one of the extensions (Firefox/Tools > Add-ons > Extensions) or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox/Tools > Add-ons > Appearance).
    *Do NOT click the Reset button on the Safe Mode start window.
    *https://support.mozilla.org/kb/Safe+Mode
    *https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes

  • How to increas the width of the Table in OBIEE Report

    Hi ,
    I am creating a OBIEE report, the report has table and 30 column in it. When I am viewing the report in an excel file , its appearing good but the width of the table is so small if I am viewing the same in internet explorer/PDF .I dont know how to increase the width of the table. Could you please sort this issue out.
    Thanks
    Govindan P

    - you can increase the width of a column -> column format values -> Additional Formatting Options
    increase the width:
    - Report level:
    result tab -> Click on Format container of Table -> Additional Formatting Options
    u can assign value width : 500 height:.....
    - dashboard level:
    Edit options -> section -> Format section -> Additional Formatting Options
    here also u can change the width
    u can assign value width : 500 height:.....
    pls mark it helps....
    Edited by: 979481 on Feb 6, 2013 1:25 AM

  • HT204150 How do I change my default email on the "Me" contact from a Facebook email to my normal email address in the same contact?  Or at least change it for the autofill information?

    How do I change my default email on the "Me" contact from a Facebook email to my normal email address in the same contact?  Or at least change it for the autofill information?
    Perfernece for contact to change.  Do I just have to dis-associate my contact fromt the facebook account?  Is only the autofill changable?

    If you allow Facebook to access your contacts and you have the @facebook.com email alias turned on, it will add the @facebook.com email to your contact info, and because it has the fixed label of "email" it overrides every other email address.
    They didn't fix this in iOS 8.
    There are two ways to remove the @facebook.com email from your contact info:
    If you don't need your Facebook friends and their info updating your contacts, go into iOS Settings -> Facebook and turn off access to Contacts.
    If you don't use your @facebook.com email address (all it does it forward to the primary email address) you can go into the Facebook app, More -> Settings -> General -> Email -> and uncheck "Use your Facebook email". Removing it from Account Emails does not work, you have to turn it off. Once you do this, go to iOS Settings -> Facebook and turn Contacts off and on again to make it update your info. The @facebook.com address should be removed.

  • How do I change just my iCloud email address not my apple ID?

    How do I change just my iCloud email address not my apple ID?

    You CANNOT change your iCloud email address once it is created and associated to you Apple Id (usually it is another email address).  First time you activate iCloud on your device and turn on email setting, you are prompted to create an iCloud email account and after choosing one that is available you are CLEARLY warned that ONCE CREATED YOU iCLOUD EMAIL IT CANNOT BE CHANGED!!!
    Fig.1 Warning if desired iCloud email      Fig. 2. Warning about creating new iCloud
    address is not available                         email which will be associated to you Apple Id
    You have two choices: a) create an alias for that account after you sign in icloud.com using either your apple id or your new created icloud email account (that's what I did) or b) create a new Apple Id (with all the pain it involves)
    I typed an incorrect iCloud email address and was linked to my Apple Id and now I have to live with this forever!?
    The workaround was to create an alias, but I have the feeling that something is wrong with my Apple Id
    All of us might make a petition to apple to allow us to change the 'main' icloud email address.  What if I misspelled it!? How difficult can it be? 
    I hope this be helpful and answer your question.
    P.S. In the same way... once you create your Apple Support Communities USERNAME it cannot be changed too!

  • Problem while changing the width of the Indesign document through inx.

    Hi Guys,
    I am facing a problem related to the width of InDesign documents. Description of the problem is as follows:-
    I have created an InDesign document with height = 700 and width = 500 and export this as an inx file (lets say Doc1.inx).
    As "Doc1.inx" is just an xml file I have made certain changes to the height and width fields of the dcoument in it. (Height =900 and Width = 600)
    For Height changes are made under following tags :- <docu>
                                                                                   <docp>
                                                                                     phgt = "U_900" ;
    For Width changes are made under tags :- <docu>
                                                                    <docp>
                                                                      pwdt = "U_600";
    Now when I opened the modified "Doc1.inx" file with InDesign the modifications for height are correctly reflected, but the width of the column doesn't gets changed. Please open the attachments to see the difference.
    Attachment contains the snap shots of documents created at step 1(Initial_Doc1.indd) and step 3(Modified_Doc1.indd).
    What should be the modifications we have to do in inx file to reflect the correct modified width of the document. Also is there any document or article which gives the correct understanding of the tags used in inx files.
    Any help will be appreciable.

    I'm having troubles getting any sensible values at all using CS -- on the other hand, you forgot to mention your version, so I figgered I could try.
    (Just as an example, setting width & height to 600 pt and 900 pt -- you don't mention your units of measure either, is it meters? inches? -- I get "phgt="u_408c2000~0" pwdt="u_4082c000~0"", which doesn't make sense. Cicero's!? [*])
    But further below, I can see some definitions for columns: count (colc="l_1") and some measurements in that same system, which I suspect to be the width and height you are looking for. You switch between describing you succesfully changed the width and height of the document, and complaining the column does not change. Apparently, the column width is defined in itself, rather than using the "document marges" you are used to in the interface itself.
    [*] On second look, I can see more hexadecimal digits in other 'numbers'. It must be hexadecimally encoded IEEE floating point numbers -- "408c2000" decodes to 4.378906, and 4082c000 to 4.085938 -- both valid floating point numbers, but still I wouldn't know in what system.
    I hope your version uses regular decimal notation!

  • Please Help!! How to get the width of the String for print out?

    Hi there,
    I need to do some printing in my application. I just want to know how can I get the width of the string when it is printed on the paper.
    I have tried to use the following code to get the width
    Rectangle2D rec = font.getStringBounds(str, new FontRenderContext(null, true, true));
    double width = rec.getWidth();
    however, the width I got from that function is not correct (the returned width is longer than the printed one)
    Does anyone know how to solve this problem?
    Thank you and Happy New Year !

    hi,
    The getFontMetrics(Font) is also defined in the Component class and therefore you can retrieve it even if you dont override the paint method.
    try the following (provided ur code extends some class that extends Component indirectly)
    FontMetrics f = this.getFontMetrics(this.getFont());
    int width = f.stringWidth(str); //str is the String for which u need to check the width.
    hope this was useful
    happy holidayz

Maybe you are looking for

  • How do I copy and paste?

    I was wondering how you copy and paste from the internet to word documents? Help would be greatly appreciated! Thanks!

  • Hi I am slightly confused with using CSS to control links.

    I have set the Hover,active and visited colour properties. the issue is that once a link has been visited the hover colour no longer shows up. So I tried removing the visited colour and now even when i hover it is staying the default purpleish. pleas

  • Reverse the confirmation

    Hi All, How can i change the specific Order Type for the purchase order as the default one. instead of the standard one given by sap , system should pick custum one as default. While tying to convert the PR to PO in the ME59 , system pick the sap sta

  • XML Gateway Seeded Function/Map for PO Creation

    Hi. I am trying to determine if existing EBS XML Gateway functions/maps exist for inserting, changing and cancelling POs into EBS. If not, I would assume then that I could build these XML Gateway components myself. Thanks.

  • Need help in WAD

    Hi Everybody,         I know what a WAD is, we create Dashboard Reporting in WAD and host it in web (please correct if i am wrong) right?, if yes, how do we host in web. i had this question in one of my interviews, which i was unable to answer. Could