How do I make a Tascam FW-1082 "work" with Logic Pro?

I just purchased logic pro and a tascam FW-1082. im trying to get them to work together, but i dont really know where to start. I ran the tascam driver, and did some configuring in logic, but it doesnt seem like they are working together seamlessly. my previous workflow involved a digi 002 with pro tools, and id like to configure logic and the tascam and logic to work like that. so, what do i do?
1.5 G4 12" powerbook/ single 1.8 g5 powermac   Mac OS X (10.4.4)   logic Pro, tascam FW-1082

It emulates a Mackie Control which Logic supports. Open the Control Surfaces setup/install window, make sure MIDI ins and outs are both connected, turn on the unit and it should appear a in couple of seconds. If it doesn't, manually install it. It's reasonably clear and the 1082 is even listed in the install window. You shouldn't have much trouble.

Similar Messages

  • Will the Tascam FW-1884 work with Logic Pro X?

    Hello,
    I notice that the new Logic is 64 bit only and yet the Tascam FW-1884 is specifically listed as a supported control surface.
    Tascam has not released 64 bit drivers for this device!  Can anyone shed any light on this?  Will it work only as a control surface and not an audio interface?  Is the documentation in error?  Anyone have this working with Logic Pro X?
    Thanks,
    Lyford Rome

    Lyford,
    Again, in regards to hardware... it is not about LPX compatibility.. It is about compatibility with the OS X version and it's CoreAudio... Once you 'get' that point then everything else makes sense...
    Tascam are notorious about leaving owners of "End of Line" products 'high and dry' when OS X is updated... and as you have found... the 1884 is not compatible with Mountain Lion 10.8.4 and likely will never be so... because Tascam will not be releasing Mountain Lion drivers for it.. so, it is not something you can use with LPX, which requires Mountain Lion 10.8.4 as a minimum requirement.
    As an aside, Apple have acknowledged they make an error in simply using the LP9 Hardware compatibility chart for LPX (as LP9 could be used with earlier OS X versions for which there were drivers for the 1884 for example) and have said they will be issuing an updated version "in the near future"......

  • Has anyone figured out how to make the Yamaha 01V96i mixer work with Logic 9.1.8

    Has anyone figured out how to make the Yamaha 01V96i mixer work with Logic 9.1.8 as a control surface ?

    In YAMAHA01v96i:
    Go to DIO/SETUP select Generic DAW. Go to MIDI settings page and set the desired port (personally I use Number 1), Select the same audio frequency you use in your DAW (I use 44.1KhZ)...at this point You should save a scene in you 01V96i to avoid to repeat all the procedure again.
    Open studio manager, go to patch and set the input port from 17 to 32 respectively to USB1-USB16 (this will give you the return from you DAW to the 01v96i
    Save again the scene overwriting the old one.
    in LOGIC
    Click on preferences, select Audio then select 01v96i, then click on control surface and select Mackie design Baby HUI and in the midi session set the same port that you've been setting on the Yamaha 01V96i (Port 1 if you follow this example).
    That's more or less it.
    It worked for me...so far

  • How would Kirk Hunter EXS24 instruments work with Logic Pro 9

    I understand that Kirk Hunter strings are quite good.  Does anyone know how the EXS24 version would work in logic pro 9? Is it just a question of putting  files in the correct directory so they show up in the media library, or is something else involved?
    Thanks
    (Note : The orchestral strings that come bundled with logic are  disappointing. For a quantitative example, playing C1 (2 Cs below middle C) of the cello, there is no contribution at the fundamental frequency of ~65 Hz, as can be seen from an EQ analyzer.)

    Kirk Hunter's EXS24 instruments work very well in Logic 9.
    Drag the instruments folder here: User>>Library>Application Support>Logic>Sampler Instruments.  (Or place an Alias of the KH instruments folder at the above location if you have your instruments stored on another drive.)
    I placed the instruments in the above location but have the samples on an external drive when using my MPB, and on a separate internal HD in my MP.
    Click on Options in the upper right of the EXS24 GUI to access Preferences.  Make sure that Search samples on... is set to All Volumes.
    The Diamond library is big bang for the buck when buying the EXS24 version.  I also have the EXS 24 version of Concert Strings ll.  But, it looks like KH is only going to release Kontakt versions of new products.  I ended up also buying the Kontakt version of Diamond.

  • How to make Kontakt player 5 work with Logic Pro X ?

    I tried adding a library but it keeps showing desired file couldnt be loaded ! Is it something to do with 64 bit or 32 bit may be ? Someone knows how to get me out of it and successfully use kontakt libraries here in PRO X ?

    No problems with Kontakt 5.3.0 here.. All works as normal with LPX.  Both the Player and the Full versions of K5 are available as a 64bit AU plugin so no issues with that and LPX
    So...
    Make sure you are using the latest version of the K5 Player...  thiough the fact you can access it within LPX tells me that's not the problem
    Therefore note:
    Not all libraries will work with the Player version however but that is by design... 
    Also not all libraries can be loaded in as a Library to the Library list but instead must be loaded via the K5 file manager...
    So, what libraries are you trying to use with the Player version of K5?
    What is the exact error msg you are getting when to attempt to add a library to K5

  • How do I make Photoshop CS6 keyframe panning work with many clips?

    Hello Photoshop experts:
    I am having big troubles with applying keyframe controlled panning in Photoshop CS6.  After reading chapter 10 of Photoshop CS6 CIAB, I added a simple cloud animation to my video.  The original video/audio track is in Video Group 1.  I pasted a simple JPEG graphic of a white cloud in to Video Group 2, without anything else in that group.    Following the CIAB directions, I was easily able to make the cloud pan across the top of my video.  Ah, this is easy I thought! 
    Then, I added a second cloud, this time it was black.  I added this to Video Group 2, right after the white cloud.  Here is where the troubles began.....  I would highlight the image frame of the black cloud, move the playback head/cursor to the right end of the black cloud clip, then click on the "Position" clock to install a yellow diamond keyframe marker.  At that instant, the selected clip of the black cloud would de-select, and the white cloud clip would select instead.  As soon as the white clould was selected, then I couldn't click and drag the black cloud, as that frame was no longer selected.  So, I would click the mouse back on the black cloud frame, and try and set the second key frame marker at the beginning of the black cloud frame for where I wanted the black cloud to sit at the start of the pan............  But then no motion would take place as I advanced the cursor across the frame. 
    So, I started a Video Group 3, and moved the black cloud into that.  Then, without problems, I was able to use the key frame markers to control the panning of the black cloud across the frame,,,,,,,,,,,  ah, this is easy!  But then, I put in a red  cloud onto Video Group 3, and guess what?  It would not work, the same as before, it only wanted to jump to the black cloud clip as soon as I had set the first key frame marker on the pink cloud.
    Note, underneath the first still image clip that I successfully automated the zoom function, there appears a violet shaded area under that clip, going from the starting key frame marker to the ending key frame marker.  It seems as though this should be telling me something, as only the working automated panning sections have the light violet highlighting.  But I can't move or eliminate that highlighting, or get it to associate with the clip I am trying to work with, after the first instance. 
    I have about 75 little clips I need to pan and zoom in on, and I am NOT going to make an individual Video Group for each clip!  Something is wrong.  I have spent about 5 hours banging my head on this today, and about 2 last night......  
    A) Maybe this is too confusing, but if someone can say what is wrong, I would appreciate any help.
    B) Can you recommend an appropriate video (YouTube or other free source) that would shine light on this?  The only videos show just one simple segment getting automated panning applied,,,,,,,,,,,  my problem does not exist in that simple case. 
    Thanks, Chuck

    Classical case of context handler overflow. Delete your file associations in Explorer, thne reinstate them using the Open With... method. also make virus scanners, compression tools and others that may add additional associations and context handlers behave by disabling their all too helpful Explorer integration options where appropriate...
    Mylenium

  • How do I get the Korg NanoKontrol to work with Logic Studio?

    I just bought a Korg NanoKontrol control surface to use with Logic Studio but it isn't working right. I can get the faders and pan to work in one scene but the transport controls don't work in any scene. If anyone knows anything about how to get it to work please let me know.

    Hey Scrooge, why the attitude? Did anyone here mistreat you? And why hijack the thread?
    Anyway, if you loose settings minutes after they worked, I would say the hardware may be shaky. Or the cabling. Or the operators' skills.
    Ambient8 has gracefully and concisely pointed the way, and if something is not working just describe what and how it is, instead of complaining (on somebody else's thread) to people who voluntarily try to offer help & solutions.
    Ambient8:
    +"Pay special attention to "Assigning Key Commands to Control Surfaces" on page >164+
    +The rest need to be set up as a control surface by using the Learn (Command+L) function to assign faders to tracks and knobs to pans, etc.+
    +See the Logic Pro 8 Control Surfaces Support guide in the Help menu for info on controller assignments. Chapter 2 "Customizing Controller Assignments" has the info assigning controllers to Logic Pro parameters."+
    If you say I did exactly as described on these pages, and all your settings seemed to disappear, I can only assume that either something is wrong with your Logic prefs, the logic.cs file or the CS itself.
    Regards, Erik.

  • How can I make my AVCHD mov. files work in premier pro?

    I used Panasonic HDC-SD60 for a short film for work.  This has over about 40 clips with around 3 hours of footage However when I import the .mov files from the media browser the audio seems fine but the footage is in a sort of slow mo, and out of sync. I want to edit and do post-production using adobe premier pro, and after effects. However the footage seems to be working in final cut X. There is no lag with playback on quicktime either. What's making this happen? I've read about variable frame rates, it's seems most common in iPhones and tablets? Is that something that the panasonic do as well? Is there a fix? Or should I jump ship and make do with a slightly more limited features of Final Cut?

    That does not specifically say Variable FRAME Rate, so I don't know a cure... but, see below
    Metadata contained in folder http://forums.adobe.com/thread/1015001?tstart=0
    -and http://helpx.adobe.com/premiere-pro/using/transferring-importing-files.html
    -http://helpx.adobe.com/premiere-pro/using/importing-assets-tapeless-formats.html

  • How can I make dragon dictate 2.5 work with Lion?

    DD 2.5 crashes and won't start even after re-installation.  Fixes?

    If you read the link from Nuance posted earlier to this thread, they don't appear to have a current software that is Lion compatible.  In the meantime, if you need voice activated commands, you can use the built-in Plaintalk support in Apple menu -> System Preferences -> Speech, or wait until Nuance upgrades their products.  Sadly Nuance took over all the third party speech recognition software available for the Mac.  A third possibility, is to get Windows installed on your Mac to do any dictation, and copy that information over to the Mac operating system in the form of an e-mail, Word document or Acrobat document if downgrading is too much of a pain.    There are these options to install Windows on your Mac*:
    http://www.macmaps.com/macosxnative.html#WINTEL
    As always, check with software developers before upgrading to ensure compatibility, and always backup your data before upgrading*:
    http://www.macmaps.com/backup.html

  • How can I make my mac book keyboard works with the Portuguese graphics accentuation, like ~`^...

    I am a new user and just bought my Mac Book. I have tried to type the texts in Portuguese using the graphics accentuation, but it is not working. I have already choiced the Portuguese language in the keyboard set up, but when I type the graphics before the letters in the text, they don`t go to the top of the letters, as it sould go. They appear before the letter, as another letter. Is there anything else that I should to set up to have the accentuation working correctly?

    If you have ever had any personal files on the iMac which you would rather not share with anyone, you should use Disk Utility to erase the hard drive using the option to write zeroes. Overwriting the files is the only way to ensure that they can't be recovered at a later date.
    After that is complete, use the restore discs that came with your iMac to reinstall all of the original software (including AppleWorks). Then use the Tiger install disc to upgrade it to Tiger.

  • Zoom H4 no longer works with logic pro and 10.5.6 update. HOw to Fix.#@##ED

    Hi all,
    i have a zoom H4 that i am using as an interface at the moment. all was fine untill i updated my computer to 10.5.6 around christmass.
    in my last post a few days ago someone said to update the H4 but it has the current drivers already (2.20)
    The zoom is now only working as an out.
    Any ideas would be appreciated.
    Thanx
    Marc

    From another thread:
    "Today I received the following reply fro Zoom regarding your issue.
    Please let me know if this does not help you.
    1. Open the "Utilities" folder from "Applications" folder.
    2. Click on "Audio MIDI Setup" icon to start "Audio MIDI Setup".
    3. Click on "Open Aggregate Device Editor" from "Audio" in menu bar.
    4. Click on "+" button to add "Aggregate Device".
    5. You can change the name to new one by double-click on "Aggregate Device". Put the new name (ex."H4 Audio IN/OUT") here.
    6. Check both "H4 Audio In" and "H4 Audio Out" boxes and click "Done" button.
    7. Set the default input and output to a newly created Aggregate Device (ex."H4 Audio IN/OUT") from the "Audio MIDI Setup" window.
    8. To use the create Aggregate Device in your DAW software, select the created "H4 Audio IN/OUT" through audio setup menu of the DAW software."

  • How can i get a downloaded plugin to work in logic pro x?

    i tried to put massive into logic pro x but i cant get it to work! ive insertet it to the folder plug-ins, components which everybody told me to do but i cant find it
    in logic once i did that! Please help me!

    If the OP did purchase Massive.. then just running the installer would have automatically installed it into the correct location...
    So... what's the bet eh Pancenter?

  • How can I make a disc cleanup on a Mac Book Pro ?

    how can I make a disc cleanup on a Mac Book Pro ?

    I'm not sure exactly what you're asking, but note that Macs don't need regular "cleaning." See The myth of the dirty Mac.

  • How do I make a 20 X 30 print with layers of 16 X 20, 12 X 18, 11 X 14, 8 X 12, 8 X 10, 5 X 7 and 4 X 6 of the same image to display the different sizes available to someone?  Using Elements 13 with Windows 8.1

    How do I make a 20 X 30 print with layers of 16 X 20, 12 X 18, 11 X 14, 8 X 12, 8 X 10, 5 X 7 and 4 X 6 of the same image to display the different sizes available to someone?  Using Elements 13 with Windows 8.1
    A senior citizen needs some help.
    Thanks

    Saving each image as different size - is it an option for you?  I would save images with their name as: 20x30.png, 16x20.png etc etc.
    Or explain whether you want these in a webpage  in which case only one image is necessary and different sizes are displayed with good CSS code.  this is question for Dreamweaver forum if this is what you want.

  • How can I make photos on web page enlarge with mouse-over?

    How can I make photos on web page enlarge with mouse-over?

    There's a couple of recent topics which mention MagicZoom and JQZoom...
    https://discussions.apple.com/message/17438064#17438064
    https://discussions.apple.com/message/17440847#17440847
    A very simple method is shown here...
    https://discussions.apple.com/message/17440847#17440847

Maybe you are looking for