How switch off time capsule?

Sorry for this idiot question, but i didnt found a clear answer for this...
Unplug power cord could damage the system no?

It is designed for 24/7 operation as vast majority of routers are.. the hard disk spin down and the power consumption drops to about 10W.. so it is no big power drain or major issue having it on.. plus electronic devices are often better continually warm than heating up and cooling down every day.. that debate is endless though.

Similar Messages

When I switch my time capsule to 5.0ghz mode the range of my wireless network drops significantly. Near the Time Capsule my Macbook Pro works fine, in my bedroom I have almost no signal. In mixed mode it works fine. Any ideas on how to get 5.0 working?

When I switch my time capsule to 5.0ghz mode the range of my wireless network drops significantly. Near the Time Capsule my Macbook Pro works fine, in my bedroom I have almost no signal. In mixed mode it works fine both placed. Any ideas on how to get 5.0 working? I thought 5.0Ghz was supposed to have a wider range. Do I need to change a setting on the Macbook Pro?
Thanks, W

I'm not sure if you understand that 5 GHz has some upsides, but also some very significant downsides.
The upside is that the 5 GHz signal will allow faster speeds.
The downside is that you must always give up something in order to gain something else.Unfortunately, the marketing hype about 5 GHz does not go into very many details about this.
In the case of 5 GHz, the 5 GHz signals are much weaker than 2.4 GHz signals, so they do not travel as far or penetrate any obstructions like walls or ceilings nearly as well as 2.4 GHz signals. In many cases, in order to get good 5 Ghz performance, you literally have to have almost a line-of-sight relationship between your computer and the wireless router.
If you have a new dual band router, which broadcasts both a 2.4 GHz and 5 GHz signal simutaneously, your Mac will connect to the best signal quality automatically depending on its location in relation to the router. In the same room, without any obstructions, it will connec to 5 GHz. But, take the laptop down the hall a few rooms and around the corner and the Mac will connect to the 2.4 GHz signal because at that location, the 2.4 GHz signal is not only stronger, it is also faster.

How to delete data off time capsule and restart

how to delete data off time capsule and restart

Open Finder > Applications > Utilities > AirPort Utility
Click on the Time Capsule, then click Edit in the smaller window that appears
Click the Disks tab at the top of the screen
Click Erase Disk
Choose the Quick Erase option
Click Erase
The procedure will take a minute or two. The Time Capsule is now ready for a new backup

How do I switch off Time Machine in Lion Server remotely?

So here's what I want to do:
I have a mac mini with OSX Lion Server running providing wireless backups for the laptops in the house. I want to rsync these backups, as sparsebundle images, to a machine at my work.
I have the rsync working over ssh correctly, and have verified that if I rsync a sparsebundle there and back again then everything works fine. However, this only works if the sparsebundle wasn't mounted at the time of the sync.
I can use 'ssh xxx@xxx "hdiutil info"' to determine if the image is mounted, but I would like ideally to be able to switch off time machine remotely for the duration of the rsync copy.
Does anyone know of a command-line way of switching off Time Machine in OSX Lion Server from the command line.
As an extra question, for bonus marks, is there any way of verifying that a sparsebundle is mountable from a windows machine?

I'm going to answer my own question:
I was more or less completely on the wrong track. When performing a networked time-machine backup the sparse bundle is mounted on the remote machine for one thing. So hdiutil won't tell me if the backup is going on.
Also, backing up the sparsebundle is probably a bad idea in general, since if it's corrupt then none of the files will be easily recoverable.
So instead I've written a bash script that
a) mounts the sparse bundle on the server machine. If this fails, then a backup is in progress. The script exits in this case, but I guess it could always try again
b) Performs an rsync on the contents of the sparsebundle
c) ejects the sparsebundle.
For those interested, here's the script. Note that I had to build rsync 3.0.9 to get this to work, the bundled rsync barfs on the hardlinks in time machine backups.
(go here http://www.behindtherack.com/?p=308 for the rsync build instructions).
And here's the script
#!/bin/bash
user=dave
remotehost=your.home.machine
remoteport=5050
sshkeyfile=~/ssh.key.file
imagepath="/Volumes/tmachine/Shared Items/Backups/machine-name.sparsebundle"
remotepath="/Volumes/Time\ Machine\ Backups/Backups.backupdb/machine-name/Latest/"
localpath=~/Local-backup-path
# mount path
mountresult=`ssh $user@$remotehost -p$remoteport -i $sshkeyfile "hdiutil mount \"$imagepath\" -readonly"`
devpath=${mountresult%% *}
# did the mount work out?
if [[ "$devpath" == /dev/disk* ]]
then
          echo "Mount succeeded, remote disk mounted to $devpath"
else
          echo $mountresult
          echo $devpath
          echo "Remote mount failed, exiting"
          exit
fi
# now run the rsync
/usr/local/bin/rsync -rv --rsync-path="/usr/local/bin/rsync" --rsh="ssh -p$remoteport -i $sshkeyfile -l $user" "$user@$remotehost:$remotepath" $localpath
# unmount sparsebundle
ssh $user@$remotehost -p$remoteport -i $sshkeyfile "hdiutil eject $devpath"

How big a Time Capsule do i need, I'm totally new to Mac!

Hi, how big a Time Capsule do I need in order for it to work as my backup? Let say if I bought an Imac with 2 TB HDD + 256 GB SSD and with that, bought a 2 TB Time Capsule for backup, would that be enough or would I need to buy a 3 TB Time Capsule? Thanx!

But if I buy the Imac I wrote about in my previous question (2 TB HDD + 256 GB SSD), would I then need to buy two, 2TB Time capsuls,
If you plan to fill up most of the space on the iMac right from the start, then you might need more space. Few users ever use more than about 75-80% of the space on their computers. I was figuring you would fill up about 75% of the drive....around 1.5 TB or so. 3 TB backup would be about right.
If I buy 1 TB HDD + 256 GB SSD, then 2 TB Time Capsule will be enough, right?
Correct.

How to use time capsule for wireless back-up but not internet?

Hello,
I have a tower and recently a laptop at work. The tower is connected to our local network with an ethernet cable and the laptop with wireless. So, the internet connection is fine for both.
I was hoping to use my time capsule to do time machine backups on my laptop. Do you have any advice on how to configure this? I do not want to use the time capsule to extend my Internet, as I believe my work I.T. would prefer to handle all access to their network.
Perhaps there is some documentation about doing this that you could point me to? I have not been able to find it.
Thank you for your help.

Your original question was How to use Time Capsule for wireless back-up but not Internet?
There is no reason for you to connect the tower....or anything else...using Ethernet if your goal remains that same as you stated.
If you are asking if you can backup the Tower using Ethernet, and not wireless, then you can connect the tower to one of the LAN <-> ports on the Time Capsule....not the WAN port.
Yes, it appears to work without plugging into my tower.
Correct, it will work.
I just have to select the network that it created. Of course, I have no access to the Internet while this is happening and it can not auto backup, unless I am on that wireless signal.
As I stated, that is the downside to trying to back up without an Internet connection. You have to establish another network...and backup over that network.
If you are asking if you can stay connected to the work network while also backing up to your non-Internet "private" network, that is not possible.

How to add Time Capsule to a Telewell ASDL Router

I tried to connect Time Capsule (2 TB a bit older model) to a Telewell ASDL Router and then run Time Machine through WiFi to Time Capsule. However, the only way I was able to make it work was to plug Time Capsule to the MacBook with an ethernet cable. When I tried to plug Time Capsule to the Telewell Router (with an ethernet cable) the internet connection of the router got disconnected. So I believe I am asking how to connect Time Capsule to the router, and if I need to do something in addition (i.e. is is possible to run two WLANs - the one from Telewell and the other from Time Capsule simultaneously?).
Thanks for your help!
Matti

Put the TC in bridge mode and plug it into the Modem.. it will work fine if you set it up before you plug it in.. I have given extremely detailed instructions here..
https://discussions.apple.com/thread/5703308?tstart=0
Are you really using Snow Leopard?? If so the manual setup from 5.6 utility is a bit different but the overall information is still correct..
You can run two different WLANs without issues.. you must setup the TC to create a wireless network anyway.. do not try to extend or join the modems' wireless .. that is wrong.
It has to be plugged into the modem by ethernet.

How fast would Time Capsule restore 500GB over wi-fi, Thanks

How fast would Time Capsule restore 500GB over wi-fi, Thanks

Using Ethernet, you normally get around 30 GB per hour transferred, so about 16-17 hours that way.
Wireless would be about 3-5 times slower, on average, so a very rough estimate would be 50-80 hours over wireless. Much depends on your actual wireless connection. Do you know what that is?

How will the Time Capsule support IPv6 and coop with the new emerging security threats that will emerge due to the new technical possibilities that IPv6 provide?

How will the Time Capsule support IPv6 and coop with the new emerging security threats that will emerge due to the new technical possibilities that IPv6 provide?

Cross your fingers and hope.
Obviously if there is any big or known threat Apple will send out a firmware fix.
But the TC is designed to be end user simple device. It has no firewall that is visible at any rate. I don't know that it truly doesn't have a firewall but it is not part of the end user controls.
IMO if you have major security concerns that go beyond end device firewall, which is where Apple do put most of the security, since firewall in the router is plainly not a stop to anybody deliberately downloading an infected file or website, and most end users.. do not want a firewall that prevents them using the web like a business does, where only certain ports are allowed. Everything else tough luck.. you are not allowed to use it. Then TC is unsuitable for you anyway.. buy a proper firewall appliance.

How to setup TIme capsule with a DSL router step by step?

Hi All,
Does anyone know how to conncet Time Capsule set by step through a DSL router?
I already have a DSL router, but want to connect my time capsule to that router.
Do i connect it through ethernet?, and is it possible to have my time capsule as a different router at home with a different password than the DSL router?, if so how is that possible?, is going to have the same download/upload speed as the DSL router?
Please help, thanks

You simply bridge the TC.
Plug it by ethernet into the adsl modem router and it will work fine.
nd is it possible to have my time capsule as a different router at home with a different password than the DSL router?,
No, the TC will cause trouble if you set it up as a router.. it has to be bridged. You only have a single adsl connection but there are some ISP that allow a secondary pppoe login and some modems that allow it. It is pretty difficult setup. Ask your ISP as there is often a charge that is very high for the second connection. It will still share the same link so there is no improvement in speed, merely two different authentications sharing the same line. The TC can do pppoe client but has nothing very fancy about it.

How to use Time Capsule via INTERNET WITH WINDOWS 7 SMB Cloud

how to use Time Capsule via INTERNET WITH WINDOWS 7 SMB Cloud

Get a vpn router.. I have no idea where you are in the world but you can find reasonable stuff for not too much money or even a general router that takes third party firmware like dd-wrt can run openvpn.
Set up the vpn router in place of the TC, as the main router in the network. Simply bridge the TC and place it behind the router. It will be accessible as part of the network via the vpn.
This is the only safe way to do it via windows.
http://www.dyncommunity.com/questions/18132/accessing-time-capsule-from-windows- 7-over-the-int.html
If you google around I have seen posts about how to access TC by port forwarding SMB on the TC.. using a different port.. To me this is going to slow down the hackers by a day or two.. then they will discover the open port and access your network.. not just the TC.. they now have SMB access to everything. Don't do it. There is very little security on SMB.

How get data off Time Capsule that otherwise doesn't work

I think a power surge caused our Time Capsule to stop working. I took it to the Apple Store today and they couldn't get it to come up and be recognized. While Apple will replace it, they said they don't help get the data off (and referred me to a couple of Apple consultants). But, they were pretty sure the data was in good shape.. just most everything else apparently wasn't working.
Do I need to use one of these 3rd party consultants to get the data off, or can I do myself? Just wondering if anyone has tried and is it easy enough for the average person to do self-serve.
Thanks.

I am having the exact same problem. I have a bunch of video on my time capsule and im in the middle of editing it and now I cant access the video and in final cut it just says media off line and there is no way to reconnect to it. Could somebody please tell us if there is a way to fix this without too much work.

How to put time capsule on new wifi network

Hi. I moved and now my wifi network name and password are different. How do I reconfigure my time capsule so that it's on the new network without losing any of my exsting information on it?

The Time Capsule is designed to function optimally when it connects to a modem/router using a wired Ethernet connection.
Are you planning to try to configure the Time Capsule to connect to your new network wirelessly?
In either case, you must reset the Time Capsule back to factory default settings and then set it up again to connect to the new network.
To do this....
Power off the Time Capsule for a few minutes
Hold in the reset button first, and then keep holding the reset button in for an additional 10 seconds while you simultaneously plug the power back into the Time Capsule
Release the reset button after the hold period, and allow a full minute for the Time Capsule to restart to a slow, blinking amber light
Now you can reconfigure the Time Capsule again to connect to the new network....and you can use the same Time Capsule device name and device password that you used before if you wish.
Resetting the Time Capsule only affects the network settings, it will not affect any of the data that you have stored on the Time Capsule hard drive.

How to 'find' Time Capsule on my computer

I used my Time Capsule to store movies. And put it into storage. Now I want to use it for Time Machine. I cannot find it on my computer. All plugged in and green light on. Airport is turned off on the TC. I cannot use TC's Airport feature for reasons irrelevant to this question. It appeared once in setting up Time Machine, but then I lost it when I unplugged the ethernet cable to rearrange cables. How do I locate TC on my computer so that I can change its configurations and use it for Time Machine?

O.K. I got it. Plugged into LAN in TC>USB converter>USB port on the Air. Restarted TC. It appeared in a Finder Window>starshipmindmachine (my Air's name) along with the other hard disks attached. Opening System Preferences>Time Machine>Choose disk, it appeared there also. Airport Utilities showed it there also, including all the preferences such as manual setup and Airport>off. It didn't do this before, but apparently the correct linking and using the paperclip to restart TC worked. Thanks for the help. Time Machine software must be one of the more schizoid creations of Silly Gulch.

How does the time capsule work?

I am unfamiliar with this device. Can anyone explain how this works? I have a Gateway NV79, an IPad 2 and an IPhone. Will the time capsule work with these devices and a printer(Officejet Pro 8600)? If so, how does it do this? I am also wondering how it works as a router? Does it provide the internet access itself or do you have to have a separate source of internet to link to the device?

A Time Capsule is a wireless router and a hard drive in one package. It does not have a modem built in, so a modem and broadband service is required if you want to be able to connect to the Internet.
As a wireless router, the Time Capsule can provide connections for up to 50 users and 3 wired Ethernet devices. If you need more Ethernet connections, a switch can be easily added to the Time Capsule for that purpose.
Your printer could connect to the Time Capsule using either a wired Ethernet connection or wireless connection
Apple's literature does a good job of describing the product. Be sure to click the links in the upper right hand corner of the main page to learn more about the Backup capabilities, Wireless performance, and detailed Specifications.
Time Capsule

How switch off time capsule?

Similar Messages

Maybe you are looking for