How to setup a 1262 aironet for Wireless N over 54mb

I've been trying to figure this out as the documentation leads me to think this can only be set to 54mb on wireless N. How can I configure a "AIR-LAP1262N-A-K9" to have wireless speeds over 54mb?
The config guide only shows settings for up to 54, but the specifications indicate it could go up to 300.
Is there something simple that I am missing?

U can get N speeds only if u have plugged all  the antennas and then if the AP is configured for either one of the below..
1>> Open Authentication with no encryption
OR
2>> WPA2 with AES as the encryption.
AND
WMM enabled and also with all MCS rates enabled..
Please do the same and this will help u in getting the N speeds..
Please dont forget to rate the usefull posts!!
Regards
Surendra

Similar Messages

  • How to setup a 1140 aironet for Wireless N

    Hi
    I need your help configuring this access points, I really dont know why I can not see speeds over 54 mpbs, I read a few documents on cisco but didnt help me with the configuration on this AP, usally made reference to model 1250 series.
    What should I enable or configure to enable high speeds on 2.4 or 5 mhz?
    This is the model that we have: AIR-AP1142N-A-K9
    Best Regards,

    The reason that WPA2 or Open are required is that the 802.11n standard requires it.  WEP is simply not allowed when operating using those data rates.  Also, WMM must be at least allowed by the SSID.
    Also, make sure that the desired MCS data rates are also enabled, whether that is from the WLC under Wireless>802.11a/n or 802.11/b/g/n, or on each radio for autonomous (can't tell from your description which you are using.)  For the WLC, there is a doc at http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a0080a3443f.shtml which describes that setup better, including requirements and troubleshooting.

  • How to setup a company code for material management

    Hi,
    While creating material in MM01, in sales org tab, when I gave plant XXXX, it is giving an error "Company code YYYY is not setup for material management".
    So can you help me , how to setup a company code for material management
    Help is appreciated
    thanks
    DIL

    Hello Sendil,
    You can maintain it with trns code OMSY or MMPI/MMPV.
    Hope this helps
    Regards
    Arif Mansuri

  • How to setup a global artwork for a TV Show

    Hi, I've a TV Show composed by 45 episodes where each one have his artwork but I don't know how to setup a global artwork for the TITLE of the TV Show while retaining the 45s artworks.
    ie. when watching the Tv Shows (library on iTunes) I would like to see the global artwork of the Tv Show that is different of the other 45s episodes contained.
    Bye, Roberto.

    Sorry, I don't believe that you have had a good look at the Foundation framework. I'll now hold your hand while we go through the basics.
    Here is the specific page http://foundation.zurb.com/docs/components/grid.html
    The default values are
    Em-base : 16px
    Row width: 62.5em (62.5em x 16px = 1000px)
    Columns per row: 12
    These and other default values can be changed. The fact of the matter is that if you stipulate a section width of 2 or 3 or 12 columns, the widths will automatically be calculated for you.
    In your case, if you want 7 columns, all you need to do is change the number of columns per row and the rest is done for you.

  • How to setup a release strategy for store generated purchase order

    Hi there,
    Does anybody know how to setup a release strategy for store/plant generated purchase order? I have a request from our client, but I never cross this before. Please help and let me know the step with every single detail.
    Greatly thank for your help.
    Kind Regards,
    2tea

    Please go thru the below Release Procedure and check whether you have maintained all the settings properly.
    PO RELEASE STRATEGY
    The release code is a two-character ID allowing a person to release (clear, or approve) a requisition or an external purchasing document. The release codes is basically controlled via a system of authorizations (authorization object M_EINK_FRG).
    Use SE12, structure CEKKO to check all the fields available for controlling the Purchase Order.
    e.g. If the total value for the Purchase Order exceeds 10,000, release strategy 01 is assigned to the Purchase Order. There is only one characteristic created in this example. For controlling the Purchase Order type, create characteristic for CEKKO-BSTYP and the value NB.
    CT04 - Create Characteristic e.g. NETVALUE
    Click Additional data Table name CEKKO Field name GNETW and press enter
    (for currency dependent field, you are prompt to enter the currency which the system then converts the currency of the Purchasing document into this currency)
    In the Basic data (X refers to tick),
    X Mutliple values
    X Interval values
    In the Value data, in the Char. value column, type >10000 and press enter
    Save your data
    CL02 - Class
    Class - Create REL_PUR
    Class type - 032
    Click Create
    Description - Release Procedure for Purchase Order
    In the Same Classification section, click Check with error
    In the Char. (characteristic) tab, type NETVALUE to assign your characteristics to the class
    OMGS - Define Release Procedure for Purchase Order Type
    Release Group - New entries
    Rel.group Rel. Object Class Description
    02 REL_PUR Rel. Strategy for PO
    Release codes - New entries
    Grp Code
    02 01
    Release indicators
    Release indicators Release Description
    0 Blocked
    1 X Release
    Release Strategy
    Release group 02
    Rel.strategy 01
    Release codes 01
    Release status 01
    Classification Choose your check values
    OMGSCK - Check Release Strategies
    (make sure there are no error messages)
    Once the Purchase Order is not release, buyers will not be able to print the Purchase Order.
    Goods Receipts will be shown with Message no. ME 390 - Purchasing document XXXXXXX not yet released.
    In 4.6c, Purchase Order with Release Strategy have a tabs at the end of the Header. This allowed the buyers to check the release status of the Purchase Order.
    The person with the release authorization have to use ME28 to release the Purchase Order.
    Regards,
    Ashok

  • How to setup a default direction for new divs in fluid grid layout in dreamweaver?

    Hi,
    how to setup a default direction for new divs in fluid grid layout in dreamweaver? I am an RTL interface user, I need my new divs to be inserted from right to left not Left to Right! could it be in dreamweaver?
    Thanks.

    This may get me into strife, but my experience is that you are better off finding another platform for your RWD.
    The framework that I tend to use is by Zub-Foundation http://foundation.zurb.com/.
    A commercial product that I have come to appreciate can be found here http://www.projectseven.com/products/tools/composer/index.htm. Please do not mention me if you happen to choose this product.

  • How to setup a default size for new divs in fluid grid layout in dreamweaver?

    Hi,
    how to setup a default size for a new divs in fluid grid layout in dreamweaver? I don't need the default size for new divs as a 100% width, I need them 13.69% as a one coulmn width only (7 coulmns fluid grids layout for desktop size 1000w).
    This problem I've faced when I intended to insert dozens of fluid grid divs in the layout.

    Sorry, I don't believe that you have had a good look at the Foundation framework. I'll now hold your hand while we go through the basics.
    Here is the specific page http://foundation.zurb.com/docs/components/grid.html
    The default values are
    Em-base : 16px
    Row width: 62.5em (62.5em x 16px = 1000px)
    Columns per row: 12
    These and other default values can be changed. The fact of the matter is that if you stipulate a section width of 2 or 3 or 12 columns, the widths will automatically be calculated for you.
    In your case, if you want 7 columns, all you need to do is change the number of columns per row and the rest is done for you.

  • How to setup the Airport Extreme for PSP?

    Can anyone tell me how to setup the Airport Extreme for PSP? I have been searching the Discussions but none of the posting seems to explain detail enough. A step by step guide would be very appreciated. Thanks.
    PowerBook G4   Mac OS X (10.4.3)  

    Sorry, I forgot to mention a few points:
    1) I don't have the Airport Extreme base station;
    2) My PowerBook is connect to the internet thru wired connection with the Built-in Ethernet;
    3) The Airport is turned on, but my PSP's scan cannot locate the PowerBook at all (while it find someone else's network)
    So, I wonder if I can just connect my PSP to the built-in Airport in the PowerBook directly. So that I can have internet access on my PSP.

  • How to setup the airport extreme for window xp

    How to setup the airport extreme for window xp

    Sorry, I forgot to mention a few points:
    1) I don't have the Airport Extreme base station;
    2) My PowerBook is connect to the internet thru wired connection with the Built-in Ethernet;
    3) The Airport is turned on, but my PSP's scan cannot locate the PowerBook at all (while it find someone else's network)
    So, I wonder if I can just connect my PSP to the built-in Airport in the PowerBook directly. So that I can have internet access on my PSP.

  • How to setup gmail push notification for my iphone 5?

    I'm using gmail. Prompt respond for mails is very urgent for me.
    How to setup gmail push notification for my iphone 5?

    I switched from a BB to an iPhone a few days ago and I knew I was going to miss the QWERTY keyboard but then I also discovered that my GMail doesn't 'push' to my iPhone. I was used to 'push' for all mail accounts on the BB. I also missed being able to personalize text, email, and phone tones for individuals.
    I tried the Gmail app for iOS and it does deliver Gmail to the iPhone app quickly but the text is tiny and when it is a web page it's almost impossible to read.
    So, I have worked out a kludge to get around these problems.
    I added my exisiting Gmail account to the iPhone.
    Hotmail does push to iOS 7 so I created a Outlook account (could be hotmail or Live) using the web browser.
    I added the hotmail account to the iPhone. I basically use this to give fast notification of important emails on my iPhone.
    On my macbook email client I created a rule that 'redirects' incoming mail to the hotmail account. The 'Redirect' is important since the email will show up in the hotmail account on the iPhone as coming from the original sender and you can then respond to the original sender from the iPhone, though the sender will see it as coming from the hotmail account.
    The other downside is that you will get a second copy of the email in the gmail inbox on the iPhone, probably 15 minutes later.
    If you don't want all of the mail being redirected you can create a 'redirect' group in the Address book and then adjust the rule in Apple mail to only redirect the mail to the hotmail account if the sender is in the redirect group. You can add and delete contacts from this group depending upon which ones you consider to be important. You will still get two copies of the email on the iPhone, one in the hotmail inbox and one in the gmail inbox.
    You can prevent this from happening temporarily by turning off, but not deleting, the gmail account on the iPhone. You could then edit the emails on the Apple email client before turning the gmail back on in the iPhone.
    And finally if you use the VIP feature in email on the iPhone you can create a list of VIP contacts and then assign a different notification sound for the VIP's. So in effect important contacts mail will be redirect to the iPhone for quick notification and very, very important contacts will have a different notification sound.
    I'm basically using the Hotmail account as a notification  tool and basically delete all the emails in it since the original copy will be in the gmail account.
    And best of all it's all free, except for the bandwidth.

  • How can setup the outgoing email for ipad2?

    How can setup the outgoing email for ipad2?

    iOS: Unable to send or receive email
    http://support.apple.com/kb/TS3899
    Can’t Send Emails on iPad – Troubleshooting Steps
    http://ipadhelp.com/ipad-help/ipad-cant-send-emails-troubleshooting-steps/
    iPad Mail
    http://www.apple.com/support/ipad/mail/
     Cheers, Tom

  • How to setup a static IP for a wireless printer

    This problem has been ongoing for several versions of OS X and the last five printers I've had and I'm finally over messing with it.  For some reson, when using a wireless printer with OS X this is a repetetive problem, and I think if I configured the printer to a static IP address instead of using DHCP, it might work better.  At least once a week, if not more often, I'll print something and get the ubiquitous Dock error of "Printer is not connected".  The printer is still in Preferences, but if I delete it, then it doesn't show up as it should for selection.
    The only way to fix this is reboot, and then the printer shows up again in Preferences.  I select it and all is well again...until a few days pass and the same thing happens again.  Using an HP LaserJet P1102w, still a current model, but it doesn't matter which printer I use.  I also have an Epson Artisan 725 and the same thing happens with it about once a week.  Also, this happens from both my Mac and my wife's Mac, so it's not an issue with just my machine.
    I've searched for documentation on how to setup a static IP address for a wireless printer with the Airport Extreme, but all I find are tutorials on how to do it with an ethernet hard-wired printer.  Any help would be greatly appreciated.

    You could set up your router to do manual assignment of IP address instead of using DHCP, but that is a PITA, because then you'd have to manually set up IP for all your devices.
    If you have AirPOrt Extreme, you could do this:
    In your Apple TV, go to the Settings >> About and write down the MAC address of your ATV
    Start up the AiPort Admin Utility
    Go to Network tab
    click + in the DHCP reservations
    Choose an IP you want for your ATV & Enter the MAC address
    From now on, this IP address will be reserved to the MAC address and only your ATV will be able to get it, no other device will.
    It is not a static IP in a true sense, but behaves just like one.
    Works great for me...
    If you don't have a AP Extreme, I'm sure other routers will allow you do reservations too.

  • New to Mac...how do I get set up for wireless internet?

    I've just been given a new Mac Book as a gift, and previously had a desktop windows computer that i used Comcast cable internet to connect to internet.
    Can someone give me some pointers as to how I need to set up my internet now so I can be wireless? Can i still go through my comcast provider?
    Thanks.

    a brody wrote:
    Welcome to Apple Discussions!
    Comcast typically does not provide a wireless solution in its own modem, but you can hook up a wireless router to their modem so your MacBook can be on wirelessly at your home. Comcast also usually gives you an ethernet modem, which most wireless routers support. If your Comcast modem is only ethernet and not WiFi, you'll need a WiFi router. Apple offers the Airport Express, Extreme, and Time Capsule wireless access points for easiest setup with the MacBook. The Express is the cheapest solution for someone with all WiFi capable machines in the house. If only the MacBook is present, you can also get a Time Capsule to be used with Mac OS X 10.5 if it is installed, to backup your Mac to a wireless hard drive, in addition to having wireless access. If you have a MacBook together with a machine with no WiFi card built-in, the Airport Extreme has LAN ports for any machine with a 10-base-T, 100-base-T, or Gigabit ethernet NIC card. Built-in to the MacBook is the ability to access the internet wirelessly at any WiFi hotspot on the road.
    I've got an Comcast/RCA branded modem with both ethernet and USB connections.
    Here's how to setup a wireless network at home with all of Apple's Airport base stations:
    http://www.apple.com/support/airport/
    Some third party 802.11n access points exist, but due to their being in draft specification, many won't give you full 802.11n access, and only give you 802.11g speeds unless their firmware is the same as Apple's.
    Most are apparently operating off of the same draft spec. I'll just note that my D-Link D-615 notes an 802.11n connection with my late 2007 MacBook.
    And "same firmware" seems to be a stretch in description. Firmware is specific to the hardware, so of course two different manufacturers are going to have different firmware - even if they are functionally compatible. Compatibility with various 802.11n draft or the eventual final standard should mean that the firmware is written to support the standard, with implied compatibility with other equipment designed to the same standard.

  • How to setup the dad file for SSO.

    Hi
    We need to setup the dad file for SSO. Can any one help us to setup the dad file.
    Thanks,
    Arvind Goel

    Hi
    It seems that SSO is for AppEx Application Authentication only. You can't specify which Database User your application will connect to the database with if you are authenticating using SSO.
    I came up against this in the following thread.
    Re: How can an AppEX Application work with DB users referenced in DB Trigge
    G.

  • How to setup the cluster environment for BPM using weblogic

    want to setup the cluster environment for BPM using weblogic....
    i have installed the oracle weblogic server 10gr3 and oracle BPM enterprise for weblogic 10gR3
    i have used the Admin tools from the "oracle BPM enterprise for weblogic" to setup the configuration and create the weblogic domain servers.
    i can launch the process administrator and import the project exp file to domain server.
    but what should i do to setup cluster environment using weblogic?
    what i want to do is :
    setup one admin machine..
    setup two product machine..
    enable the cluster so the admin machine can monitor the status of the product machine..
    thanks a lot ...

    The install guide at http://download-llnw.oracle.com/docs/cd/E13154_01/bpm/docs65/config_guide/index.html gives a reasonable amount of info on how to do this.
    Personally I have not used the OBPM option to configure WebLogic instead I've used the information in the above install guide to create the weblogic domain in advance of configuring OBPM.
    Once you've setup WebLogic configure OBPM using the values I mention in the following thread: How to set the JMX Engine parameter in Process Administation?
    Let me know any specific config questions and I'll do my best to answer them for you.
    Thanks,
    Mike

Maybe you are looking for