HT201210 When I try to do a software upgrade from 4 to 6 on my ipad I get a Network error message.  i have full internet access. Any ideas?

I am trying to upgrade my ipad ios 4 to IOS 6 or above. I  get a network error code saying the ipad upgrade server cannot be contacted. I do have full internet access on a high speed connection. Any suggestions?

If you have an iPad 1, the max iOS is 5.1.1. For newer iPads, the current iOS is 7.1. The Settings>General>Software Update only appears if you have iOS 5.0 or higher currently installed.
You can no longer update to iOS 6.x, or down grade the iOS.
iOS 5: Updating your device to iOS 5 or Later
http://support.apple.com/kb/HT4972
How to install iOS 6
http://www.macworld.com/article/2010061/hands-on-with-ios-6-installation.html
iOS: How to update your iPhone, iPad, or iPod touch
http://support.apple.com/kb/HT4623
If you are currently running an iOS lower than 5.0, connect the iPad to the computer, open iTunes. Then select the iPad under the Devices heading on the left, click on the Summary tab and then click on Check for Update.
Tip - If connected to your computer, you may need to disable your firewall and antivirus software temporarily.  Then download and install the iOS update. Be sure and backup your iPad before the iOS update. After you update an iPad (except iPad 1) to iOS 7.x, the next update can be installed via wifi (i.e., not connected to your computer).
Tip 2 - If you're updating via wifi, place your iPad close to your router to preclude getting a corrupted download.
How to Upgrade to iOS 7
The iOS 7.0 update requires around 2.5 GB of storage space, so if your iPad is almost full, you may need to clear up some space. You can check your available space in Settings -> General -> Usage.
There are two ways to upgrade to iOS 7: You can use your Wi-Fi connection, or you can connect your iPad to your PC and update through iTunes. We'll go over each method.
To upgrade using Wi-Fi:
Note: If your iPad's battery is under 50%, you will want to plug it into your charger while performing the update.
Go into the iPad's Settings.
Locate and tap "General" from the menu on the left.
The second option from the top is "Software Update". Tap this to move into the update settings.
Tap "Download and Install". This will start the upgrade, which will take several minutes and will reboot your iPad during the process. If the Download and Install button is grayed out, trying clearing up some space. The space required by the update is mostly temporary, so you should gain most of it back after iOS 7 is installed.
Once the update is installed, you may have to run through the initial steps of setting up your iPad again. This is to account for new features and settings.
To upgrade using iTunes:
First, connect your iPad to your PC or Mac using the cable provided when you purchased your device. This will allow iTunes to communicate with your iPad.
You will also need the latest version of iTunes. Don't worry, you will be prompted to download the latest version when you launch iTunes. Once it installs, you may be asked to setup iCloud by logging into your iTunes account. If you have a Mac, you may be prompted on whether or not you want to enable the Find my Mac feature.
Now you are ready to begin the process:
If you upgraded iTunes earlier, go ahead and launch it. (For many, it will launch automatically when you plug in your iPad.)
Once iTunes is launched, it should automatically detect that a new version of the operating system exists and prompt you to upgrade to it. Choose Cancel. Before updating, you will want to manually sync your iPad to make sure everything is up to date.
After canceling the dialog box, iTunes should automatically sync with your iPad.
If iTunes doesn't automatically sync, you can manually do it by selecting your iPad within iTunes, clicking on the File menu and choosing Sync iPad from the list.
After your iPad has been synced to iTunes, select your iPad within iTunes. You can find it on the left side menu under Devices.
From the iPad screen, click on the Update button.
After verifying that you want to update your iPad, the process will begin. It takes a few minutes to update the operating system during which time your iPad may reboot a few times.
After updating, you may be asked a few questions when your device finally boots back up. This is to account for new settings and features.
 Cheers, Tom

Similar Messages

  • When I try to open a Pages document from iCloud, created on my iPad, I get message stating I need a newer version of Pages.  When I go to app store all I get is "installed" when looking at pages app. my Macbook pro is up to date with all updates.

    When I try to open a Pages document from iCloud, created on my iPad, I get message stating I need a newer version of Pages.  When I go to app store all I get is "installed" when looking at pages app. my Macbook pro is up to date with all updates. Any ideas?

    You have 2 versions of Pages on your Mac.
    Pages 5 is in your Applications folder.
    Pages '09/'08 is in your Applications/iWork folder.
    You are alternately opening the wrong versions.
    Pages '09/'08 can not open Pages 5 files and you will get the warning that you need a newer version.
    Pages 5/5.01 can not open Pages 5.1 files and you will get the warning that you need a newer version.
    Pages 5.1 sometimes can not open its own files and you will get the warning that you need a newer version.
    Pages 5 can open Pages '09 files but may damage/alter them. It can not open Pages '08 files at all.
    Once opened and saved in Pages 5 the Pages '09 files can not be opened in Pages '09.
    Anything that is saved to iCloud is also converted to Pages 5 files.
    All Pages files no matter what version and incompatibility have the same extension .pages.
    Pages 5 files are now only compatible with themselves on a very restricted set of hardware, software and Operating Systems and will not transfer correctly on any other server software than iCloud.
    Apple has not only managed to confuse all its users, but also itself.
    Note: Apple has removed over 100 features from Pages 5 and added many bugs:
    http://www.freeforum101.com/iworktipsntrick/viewforum.php?f=22&sid=3527487677f0c 6fa05b6297cd00f8eb9&mforum=iworktipsntrick
    Archive/trash Pages 5, after exporting all Pages 5 files to Pages '09 or Word .docx, and rate/review it in the App Store, then get back to work.
    Peter

  • When I try to upload a web gallery from Lightroom5.4  to business cataylst I get an unknown error

    Im using the latest lightroom and BC software but when I follow the videos to create and post a lightroom web gallery into a BC hosted site I just get an unknown error message. IVe watched every video and  still get the same outcome!

    I have this error also when I try to upload to the PearsonMyLabandMastering site. I have uploaded files using Firefox extensively up until this week. I cannot say for sure, but I don't believe it happened until after I upgraded to 7.0.
    BTW, the files upload just fine with Chrome. I did not check IE.

  • When I try to connect LDAP server with Directory certificate installed in Onboard Administrator , I get the below error message. Initiating Directory Settings diagnostic for LDAP server 10.0.0.2 port 636

    10.0.0.2Accepting Directory Server certificate for /CN=qtp-ldap.oaqtp.com signed by /DC=com/DC=oaqtp/CN=qtp-ldap
    Skipping certificate 1 (/CN=qtp-ldap.oaqtp.com): subject issuer mismatch 
    Certificate of Directory Server cannot be verified with the installed LDAP certificate. 
    Unable to establish SSL connection with directory server. 
    You may need to install a certificate for your server to allow SSL connections. 
    It says "Subject Issuer mismatch" .. What could be the reason ?
    -Shibi Keyan

    Well, it sounds like the certificate name is different than what you are trying to connect to. Can you try connecting to the DNS name instead? This sounds like a DNS and Certificate Name issue.
    http://social.technet.microsoft.com/wiki/contents/articles/2980.ldap-over-ssl-ldaps-certificate.aspx
    Kurt Hudson, Sr. Technical Writer AD DS, AD CS, PKI, Azure AD

  • When I try to convert an existing Word intake form into a fillable PDF, I get an unexpected error.

    When I try to convert an existing Word intake form into a fillable PDF, I get an unexpected error message and it will not convert.  I am using Adobe XI Pro.  Any thoughts on why this is occuring.  I would like to avoid creating an entire new form from scratch.  If this doesn't work, I will not be purchasing the full version of the software as none of my Word files seem to be converting.

    I used the document which I downloaded from Adobe called "Convert and existing form into a fillable PDF form with Adobe Acrobat XI". 
    At tope right , Tools pane
    Open the Forms panel, Click Create
    Select Existing Document and click Next
    Choose Word file
    Error: "An unexpected error occurred. PDF Maker was unable to produce the Adobe PDF."
    I have tried several of my forms and none of them work.  There is no word attachment option to show you an example.
    Thanks

  • Sometimes (but not always), when I try to open a pdf document from the US bankruptcy court website, I get a window asking if I want to use Adobe Acrobat. After I click "yes", I get a bland screen.

    == Issue
    ==
    Firefox is having problems with certain web sites
    == Description
    ==
    Sometimes (but not always), when I try to open a pdf document from the US bankruptcy court website, I get a window asking if I want to use Adobe Acrobat. After I click "yes", I get a bland screen.
    == URL of affected sites
    ==
    http://
    == Troubleshooting information
    ==
    Firefox Version
    3.6.3
    Extensions
    Name
    Version
    Enabled
    ID
    Skype extension for Firefox 2.2.0.70 false
    Java Console 6.0.01 false
    Java Console 6.0.02 true
    == Firefox version
    ==
    3.6.3
    == Operating system
    ==
    Windows 7
    == User Agent
    ==
    Mozilla/5.0 (Windows; U; Windows NT 6.1; en-US; rv:1.9.2.3) Gecko/20100401 Firefox/3.6.3
    == Plugins installed
    ==
    *-Office Plugin for Netscape Navigator
    *Download and Print Plug-in DLL
    *Default Plug-in
    *Shockwave Flash 10.0 r45
    *Adobe PDF Plug-In For Firefox and Netscape

    Hi.
    Does this only open on that specific site?
    In any case, you may want to:
    - instruct Firefox to handle PDF files in a specific way by going into Tools > Options > Applications and selecting the option you want for the PDF files
    - reinstall Adobe Reader and its Firefox plugin
    - install another reader instead of Adobe Reader. I recommend Foxit Reader ( http://www.foxitsoftware.com/pdf/reader/ ), since it's free, VERY light, VERY fast, safe and also has a Firefox plugin (make sure you don't have both Adobe Reader plugin and Foxit Reader plugin enabled/installed at the same time in Firefox)

  • I loaded Digital Editions onto a second computer at home.  When I try to download a book from the library I get the following error message: E_Act_Not_Ready, License Server Communication.  Any suggestions?

    I loaded Digital Editions onto a second computer at home.  When I try to download a book from the library I get the following error message: E_Act_Not_Ready, License Server Communication.  Any suggestions?

    Having exact same problem, only it's with a book I've paid for, so it hurts more . Any ideas?

  • When I try to print a photo downloaded from Facebook in iPhoto, I can't get the size I specify to print correctly. Example: 5x7 prints smaller than 5x7. What do I do to solve this problem?

    When I try to print a photo downloaded from Facebook in iPhoto, I can't get the size I specify to print correctly. Example: 5x7 prints smaller than 5x7. What do I do to solve this problem?

    Those pixel dimemsions have aspect ratios that are not the same as a 5 x7 print:
    1360 x 1360 = 1.0
    790 x 640 = 1.23
    2048 x 1366 = 1.5
    An 7 x 5 image = 1.4.
    So you'll need to crop the images to 5 x 7 before printing.  The first two images are a little light in the pixels to produce a high resolution 5 x 7 print. 
    Happy Holidays

  • When i try to use facetime on my imac it comes up with facetime not responding and starts to use nearly 2gb of memory. Any ideas please?

    when i try to use facetime on my imac it comes up with facetime not responding and starts to use nearly 2gb of memory. Any ideas please?
    Also messages does the same thing

    Hello BassoonPlayer,
    Since you are using one of the the school's Macbooks, it is quite possible that the time and date are not properly set on the computer that you are using.  FaceTime will not work if you do not have the proper time zone set up for the location that you are in.  This past week, there were a two other Macbook users I've helped by simply telling them to set the Date/Time properly.  By the way, you described your problem very well, which makes it easier for us to help you.  Hope this solves your problem -- if not, post back and I can suggest other remedies.
    Wuz

  • HT203176 i have a slow macbook, i ran live disk utilities and said I need to repair disk from a cd. did that, I got volume repaired from the external disk. when I reboot from hdd, then run disk utility, I get the same error message i did b4 repair

    i have a slow macbook, i ran live disk utilities (from hard drive), turned out I needed to repair disk from a installation disk. Did that, I got the volume (Hard drive) repaired from the installation disk disk. To this point, great!
    When I reboot from hdd, then run disk utility, I get the same error message i did b4 repair. I went thru two rounds of this.....
    Can anyone help? thanks

    Sorry guys, I don't see how to reply to you so I use reply to "me" basically.
    So the error I get is "volume header needs minor repair" and then you need to perform repair from the installation disk message.
    I did repair not verify from the disk twice. Every time ending in the "the volume had ha been successfully repaired". Then I reboot from the internal disk. Run disk utilities from it, do verify and get the same error message I got before repair. I hope this can shed some light fr you guys. Sorry I didn't include details in the original
    MEssage.

  • I work with a Mac & I had to restore my computer for my time machine back-up.  When I attempt to open/edit a photo with either camera raw or photoshop I get the following error message: Error 150:30 , it also sys that licensing for the product has stopped

    I work with a Mac & I had to restore my computer for my time machine back-up.  When I attempt to open/edit a photo with either camera raw or photoshop I get the following error message: Error 150:30 , it also sys that licensing for the product has stopped working?

    Unfortunately when Adobe products are restored from backup, especial CS4 and especially Mac, it breaks licensing.
    There is a python script included in the license recovery kit that should work if you are familiar with Terminal.
    If not, you must reinstall your CS4 suite.  You don't need to delete your preferences, so it should be the same as before.
    Error "Licensing has stopped working" | Mac OS
    Gene

  • When I wants to syncronize my foto's from my computer to my Ipad, Ik get the message  "itunes photprocessor was not installed correctly, please reinstall itunes, error 7"  When i did so, the same message appears again and again??????

    When I want to syncronize my photo's from my computer to my Ipad, I get the message  "itunes photoprocessor was not installed correctly, please reinstall itunes, error 7"
    When I did so, the same message appears again and again.
    Anyone knows the solution?
    Thanks on forhand.

    Repair Apple Application Support.
    START/CONTROL PANEL/PROGRAMS N FEATURES/highlight APPLE APPLICATION SUPPORT, then click the REPAIR button

  • How do I activate iMessage when it tells me that I need to check my network connection but I have full internet connection?

    How do I activate iMessage when it tells me that I need to check my network connection but I have full internet connection?

    iOS: Troubleshooting FaceTime and iMessage activation                           
    FaceTime, Game Center, Messages: Troubleshooting sign in issues

  • When I use the shortcut to open a new window in safari (command N), I get a 404 error message from Google. How do I change where 'Command N' routes to?

    When I use the shortcut to open a new window in safari (command N) on my Macbook Pro, I get a 404 error message from Google. How do I change where 'Command N' routes to? 

    It's not necessary to change the Command N keystroke..
    From your Safari menu bar click Safari > Preferences then select the Privacy tab.
    Click:   Remove All Website Data
    Then delete the cache.
    Open a Finder window. From the Finder menu bar click Go > Go to Folder
    Type or copy paste the following
    ~/Library/Caches/com.apple.Safari/Cache.db
    Click Go then move the Cache.db file to the Trash.
    Quit and relaunch Safari to test.
    If that didn't help, troubleshoot Safari extensions.
    From the Safari menu bar click Safari > Preferences then select the Extensions tab. Turn that OFF, quit and relaunch Safari to test.
    If that helped, turn one extension on then quit and relaunch Safari to test until you find the incompatible extension then click uninstall.

  • I purchased my iMac used.  When I try to update my apps the computer automatically fills in the previous owner's Apple ID and I can't change it.  Any ideas?

    I purchased my iMac used.  When I try to update apps in AppStore, the computer automatically fills in the previous owner's email address and it won't let me delete it to enter mine.  I have been using my own apple ID and password on this computer for other things without a problem.  Any ideas?

    Before buying a second-hand computer, you should have run Apple Diagnostics or the Apple Hardware Test, whichever is applicable.
    The first thing to do after buying the computer is to erase the internal drive and install a clean copy of OS X. You—not the original owner—must do that. Changes made by Apple over the years have made this seemingly straightforward task very complex.
    How you go about it depends on the model, and on whether you already own another Mac. If you're not sure of the model, enter the serial number on this page. Then find the model on this page to see what OS version was originally installed.
    It's unsafe, and may be unlawful, to use a computer with software installed by a previous owner.
    1. If you don't own another Mac
    a. If the machine shipped with OS X 10.4 or 10.5, you need a boxed and shrink-wrapped retail Snow Leopard (OS X 10.6) installation disc from the Apple Store or a reputable reseller—not from eBay or anything of the kind. If the machine is very old and has less than 1 GB of memory, you'll need to add more in order to install 10.6. Preferably, install as much memory as it can take, according to the technical specifications.
    b. If the machine shipped with OS X 10.6, you need the installation media that came with it: gray installation discs, or a USB flash drive for a MacBook Air. You should have received the media from the original owner, but if you didn't, order replacements from Apple. A retail disc, or the gray discs from another model, will not work.
    To start up from an optical disc or a flash drive, insert it, then restart the computer and hold down the C key at the startup chime. Release the key when you see the gray Apple logo on the screen.
    c. If the machine shipped with OS X 10.7 or later, you don't need media. It should start up in Internet Recovery mode when you hold down the key combination option-command-R at the startup chime. Release the keys when you see a spinning globe.
    d. Some 2010-2011 models shipped with OS X 10.6 and received a firmware update after 10.7 was released, enabling them to use Internet Recovery. If you have one of those models, you can't reinstall 10.6 even from the original media, and Internet Recovery will not work either without the original owner's Apple ID. In that case, contact Apple Support, or take the machine to an Apple Store or another authorized service provider to have the OS installed.
    2. If you do own another Mac
    If you already own another Mac that was upgraded in the App Store to the version of OS X that you want to install, and if the new Mac is compatible with it, then you can install it. Use Recovery Disk Assistant to prepare a USB device, then start up the new Mac from it by holding down the C key at the startup chime. Alternatively, if you have a Time Machine backup of OS X 10.7.3 or later on an external hard drive (not a Time Capsule or other network device), you can start from that by holding down the option key and selecting it from the row of icons that appears. Note that if your other Mac was never upgraded in the App Store, you can't use this method.
    3. Partition and install OS X
    a. If you see a lock screen when trying to start up from installation media or in Recovery mode, then a firmware password was set by the previous owner, or the machine was remotely locked via iCloud. You'll either have to contact the owner or take the machine to an Apple Store or another service provider to be unlocked. You may be asked for proof of ownership.
    b. Launch Disk Utility and select the icon of the internal drive—not any of the volume icons nested beneath it. In the  Partition tab, select the default options: a GUID partition table with one data volume in Mac OS Extended (Journaled) format. This operation will permanently remove all existing data on the drive.
    c. An unusual problem may arise if all the following conditions apply:
              OS X 10.7 or later was installed by the previous owner
              The startup volume was encrypted with FileVault
              You're booted in Recovery mode (that is, not from a 10.6 installation disc)
    In that case, you won't be able to unlock the volume or partition the drive without the FileVault password. Ask for guidance or see this discussion.
    d. After partitioning, quit Disk Utility and run the OS X Installer. If you're installing a version of OS X acquired from the App Store, you will need the Apple ID and password that you used. When the installation is done, the system will automatically restart into the Setup Assistant, which will prompt you to transfer the data from another Mac, its backups, or from a Windows computer. If you have any data to transfer, this is usually the best time to do it.
    e. Run Software Update and install all available system updates from Apple. To upgrade to a major version of OS X newer than 10.6, get it from the Mac App Store. Note that you can't keep an upgraded version that was installed by the original owner. He or she can't legally transfer it to you, and without the Apple ID you won't be able to update it in Software Update or reinstall, if that becomes necessary. The same goes for any App Store products that the previous owner installed—you have to repurchase them.
    4. Other issues
    a. If the original owner "accepted" the bundled iLife applications (iPhoto, iMovie, and Garage Band) in the App Store so that he or she could update them, then they're irrevocably linked to that Apple ID and you won't be able to download them without buying them. Reportedly, Mac App Store Customer Service has sometimes issued redemption codes for these apps to second owners who asked.
    b. If the previous owner didn't deauthorize the computer in the iTunes Store under his Apple ID, you wont be able to  authorize it immediately under your ID. In that case, you'll either have to wait up to 90 days or contact iTunes Support.
    c. When trying to create a new iCloud account, you might get a failure message: "Account limit reached." Apple imposes a lifetime limit of three iCloud account setups per device. Erasing the device does not reset the limit. You can still use an iCloud account that was created on another device, but you won't be able to create a new one. Contact iCloud Support for more information. The setup limit doesn't apply to Apple ID accounts used for other services, such as the iTunes and Mac App Stores, or iMessage. You can create as many of those accounts as you like.

Maybe you are looking for

  • Error occurs during Asset Master Record Creation.

    Hello SAP Gurus, The error occurs during asset master record creation. Our fiscal year variant is Z6 (July to June). The asset was acquired in June 15 (previous fiscal year) but was only set up on July 30 (this fiscal year) . When we put the deprecia

  • Cost of replacing hard drive on my powerbook G4

    I bought my powerbook about 2 years ago and to be honest, have loved it a lot. Today after a coffee break, I sat to work on my PB and it was very slow...then began a host of problems which have ended with it not starting up. I have done disk utility

  • Against PR when created the PO,price is not picking from PR to PO?

    Hello Gurus, Against the PR,created the PO system is not picking the price from PR to PO ?

  • Business Graphics UI SimpleSeries Changing Label Dynamically

    Hi guys, I am using the business graphic UI element in one of my WD4A component. My BG has 2 simple series and one category. As I can see, using simple series, the label property cannot be bound against a context node attribute. I have to find a way

  • VC 7.1 View in wizard

    Hi all, I have the following problem. When I try to integrate a view that contains a data service in a wizard, the data service doesnt get called. When I integrate the view via the navigate option (or as nested view in different application) the data