HT4279 Upgrades for Mac Pro 2008

Besides memory and Storage are there any other hardware upgrades available, video card, CPU, etc.?

http://store.apple.com/us/product/MC742ZM/A

Similar Messages

  • Where can I find internal DVD replacement for Mac Pro 2008?

    My optical DVD drive on my Mac Pro (3,1) has been dead for a good long while. 
    Looking for a cheap replacment.  Just saw OWC stopped carrying them.  Any leads?

    For Mac Pro 3,1 and earlier (2008 and previous) you need an IDE/ATA drive like this one:
    http://eshop.macsales.com/shop/superdrive/Mac_Pro_Xeon

  • Memory Upgrade for Mac Pro 1,1

    Hello,
    I have what I believe is a first generation Mac Pro. The system profiler says it's version 1,1.
    When I bought it, I had an additional 2 GB of ram installed by the dealer for a total of 3GB.
    Today I am trying to install a pair of 2GB DIMMS for a total of 7GB.
    I bought the memory at my local mac dealer (Mac Enthusiasts in West LA). He asked what version of Mac I had and I said I thought it was first generation. He asked for the serial number, but I didn't know I needed one. I did however bring the manual and told him the date was 2006.
    He assured me he had the right memory for my machine, despite my offering to get the serial number from home.
    The point of all this is when I opened up my mac to install the memory, I was surprised to see that the original factory memory had HUGE BLACK HEAT SINKS on it. The second, dealer-installed memory had SLIM SILVER HEAT SINKS, and now finally the memory I bought today has NO HEAT SINKS WHATSOEVER.
    Is it possible that memory technology has improved and newer DIMMS run cooler and don't need heat sinks? Or do I have the wrong memory? Is there any online guide or utility I can use to determine if I can use these modules?
    Finally, here is the text on the sticker of the modules:
    2GB PC2-5300 (667Mhz) DDR2 DIMM
    The chips themselves appear to say "Lynnix" KOR
    Please help.
    Thanks,
    P-FO

    You indeed have the first generation Mac Pro. It can use up to 8 - 240-pin PC2-5300 (667MHz) DDR2 ECC fully-buffered DIMM (FB-DIMM) in (matched pairs.) The modules should have an Apple certified or similar heat sink. Do not use DIMMs without heat sinks as they will not last and may be subject to frequent errors. The DIMMs must be fully buffered (FB) and must be error correcting (ECC) and installed in matching pairs.
    Whatever your local dealer sold you if there's no heat sink, they aren't FB and ECC modules, then don't use them.
    For proper installation see the following:
    About RAM installation in the Mac Pro
    Mac Pro memory arrangement photos
    Mac Pro Memory Configuration
    Memory Tests- "2008" Mac Pro
    Ram should be installed minimally in matched pairs and optimally in matched quads. This means the memory modules are the same size and specifications. They should also be equipped with the Apple-certified style of heat sink.

  • Pci-e usb 3.0 compatible cards for Mac Pro 2008

    Anyone know a list of compatible USB 3.0 pci-x cards. Unofficial working list is what I am looking for. I have a Mac Pro early 2008 OSX Macverick
    Thanks in advance for the help.

    It  depends. And they are PCIe.
    Sonnet Allegro works fine for me, but apparently not for Drobe.
    CalDigit is popular.
    Do a favor, some cards require 10.8.2 or later so always include your OS.
    www.macsales.com is always a good place to start your looking - if they sell it and they tend to sell what is supported and works.

  • Video card upgrades for Mac Pro 3.0Ghz quadcore, Video card upgrades for Mac Pro 3.0Ghz quadcore

    Looking for advice on Mac Pro with a dying video card. This the early Xeon dual core 3.0Ghz with an ATI Radeon X1900. Maybe the Nvidia Quadro 4500. I know there is s Quadro 4800 which I don't know if will will work with this older Mac Pro. Links and advice is appreciated.

    Both cards will work with your computer although that's not stated on Apple's website. I'm using a 5770 in a first generation Mac Pro and it works quite well. I can't get the best performance from it because my MP only has PCI Express 1.0 slots.

  • Logic pro 7.1.1 upgrade for mac pro

    My logic version is power pc based and its using my cpu power to decode it to intel based.Do you know if i can upgrade it to 7.2 and how?
    Thanks!

    Yes - simply buy the 7.2 crossgrade from Apple for about 50 bucks.
    It requires Logic 7.

  • Mac Pro 2008 - upgrade to 2010 model or not?

    I have a Mac Pro 2008 2.8 gHz with 12GB RAM. I'm not running Premiere Pro CS5 which is great and seems to love RAM and processor speed. I also recently got a CUDA card to take advantage of it's GPU acceleration.
    My question is: Should I get a new Mac Pro 2010, 6, 8, 12 core or just upgrade my RAM to say, 24GB and perhaps get some SSDs (maybe even in a RAID 0) as my boot drive.
    The RAM upgrade will be in the $650 range, SSDs could be at least that. I'll need RAM anyway for a new model as my old RAM isn't compatible.
    Getting a new model could set me back $5000 (or more) when it's all loaded.
    I'm also a little disappointed in the 2010 Mac Pros, for example my 2008 Mac pro was a no-brainer, but now I'm ambivalent about this upgrade to 2010, thinking there may be new models out this year that fill in all the holes. I kind of feel like the 2010 Mac Pro upgrade was a little like the Final Cut Pro 7 upgrade, it was a stop gap because Apple needed to do something. I could be wrong about this though.
    I know this is kind of a difficult question to answer, but if you have any opinions, please feel free to lend any advice.

    PCIe 3.0
    USB3
    Intel SATA3 6G
    Socket LGA1356
    Socket LGA2011
    3G SSD (by the time 4th Gen SSDs are out, one unit would make out our current SATA channel bandwidth)
    Mid-range Xeon roadmap:
    Socket LGA1356, a direct replacement for the current Socket LGA1366. The parts here are 6-core and 8-core Sandy Bridge single-socket and dual-socket capable but mid-range positioned Sandy Bridge Xeon - and, ultimately, Core i7 - parts with up to 20MB of L3 cache, three DDR3-1600 memory channels just like the existing LGA1366 Westmeres with one memory speed grade higher, and 24 PCIe v3 lanes on-chip.
    The single external QPI v2 link runs at up to 8 gigatransfers/sec, or 32GB/sec bidirectional bandwidth, a 25 per cent speed up over the current generation, but also feeding a third more cores on each socket.
    http://www.theinquirer.net/inquirer/feature/1811091/2011-intel-xeon-update-holy- socket-trinity
    Intel is set to replace its current high-end socket, LGA1366, when it releases its new 8-cores processors in the Late 2011. This socket is expected to be released alongside Sandy Bridge-EX in Q3 2011, and will support 4 memory channels as well as 40× PCIe 3.0 lanes.
    http://en.wikipedia.org/wiki/LGA_2011

  • Reviews for ATI Radeon HD 4870 Graphics Upgrade Kit for Mac Pro?

    There's no review at the Apple Store on this [ATI Radeon HD 4870 Graphics Upgrade Kit for Mac Pro (Early 2009 or Early 2008)|http://store.apple.com/us/product/MB999ZM/A?fnode=MTY1NDA5OQ&mco=NDE4NDMx OA]. Googled and found nothing related to the Mac kit. Mostly PC based.
    Should I consider this card? I need a spare/replacement graphics card for my Mac Pro (early 2008). The NVIDIA GeForce 8800 GT card has failed me twice.

    Just came out on barefeats:
    http://www.barefeats.com/nehal14.html
    Shows new drivers with 285, also compares 4870.
    If you play a lot of games on the windows side, you might also want to consider the 4890. I has recently became flashable (if you're into that kinda thing). It has a lot more leeway to be overclocked. Close to (or if your lucky) hitting the 1 Ghz core clock speed, gives very close comp to the 285, and at fraction of the price. You can get an XFX 4890 on newegg for $195.

  • Compatible HD for Early Mac Pro 2008

    Hello All,
    I have two failing drives in my early Mac Pro 2008 and its time to find some replacements. The drives I need to replace are 1TB in size but I was looking to get something larger being 1.5TB. I read on a site that this version of Mac Pro supports a maximum of 4TB accross all the four bays which would essentially mean a maximum of 1TB for each Bay. Here is the link to the site: http://www.everymac.com/systems/apple/mac_pro/faq/mac-pro-how-to-upgrade-hard-dr ives-what-type-supported.html
    Question I have, is whether its safe to add two 1.5TB drives (I also have a 640GB for the boot and 500GB additional data drive) or should I stick with 1TB drives? Also, is there any advantage in going beyond the 3Gb/s Serial ATA spec as I would suspect the faster drives would not be utilized to their capacity given the older data path in this machine.
    Any help/advice would be appreciated and thanks in advance!
    Cheers,
    Vin.

    You can put any make and any size 3.5" drive in all the bays in any combination.  Also SATA 3's will work but of course at not their full maximum speed as you mentioned so SATA 2's are OK.
    As an example, if you got 4 3TB's you could stuff them in there for a max of 12TB.  Bit of overkill unless you really need all that space!
    Personally I like Western Digital 1TB and 2TB blacks.
    You might also want to consider using an SSD as your boot drive.
    Update: I took a look at that site you linked.  That 4TB limit is the max any one drive bay can support, not the total capacity across all 4 bays.

  • GeForce 7300 GT Upgrade Kit for Mac Pro?? G5?

    Hi,
    Just found this on the apple store:
    http://store.apple.com/Apple/WebObjects/ukstore.woa/wa/RSLID?mco=1643C421&nplm=M A567
    "NVIDIA GeForce 7300 GT Graphics Upgrade Kit for Mac Pro"
    Why is it only for mac pro? its PCI express & my g5 is one of the late 2005 models and it has PCI Express so am i wrong in thinking that this should work fine or is it something to do with the new intel architecture?
    If i remember correctly i could have chosen this card or a very similar one when i configured my G5.
    Thanks

    That card is only for the Mac Pro, as it says.
    When you ordered your G5, you had the choice of the nVidia 6600 (or 6600LE), nVidia 7800GT, or the Quadro FX 4500.
    The 7800GT that you could have ordered with your G5 is close in performance to the ATi X1900XT that is an option on the Mac Pro. The 7300GT that you're looking at is an entry level card, which the 7800GT definitely is not.
    The 7300GT and the X1900XT are both Mac Pro only due to the ROM on the card, which is designed to work with the EFI booting hardware that the Mac Pro uses. The G5s used Open Firmware, which requires a different ROM on the video card. So, even though both your G5 and the Mac Pro are PCI-Express based, these video cards are not compatible.
    Now, most PCI-Express cards that you look at for, say, external SATA, will probably work in both the G5 and the Mac Pro. You'd still want to check the specs to be sure, however.
    If you're looking for a new video card to replace your (presumably) nVidia 6600, your only real option is the ATi X1900 G5 edition. This is a different card than the X1900XT that's offered for the Mac Pro.

  • Hardware for Mac Pro early 2008

    Hi there
    We have very old Macs at our university. We will renew them next year, however we need to hook up our magnificent video monitors to Premiere Pro CC. There is only DVI and FireWire signal out, no thunderbolt. Inputs on the monitor are HD SDI and HDMI.
    I´m sure there must be Hardware for this Mac Pro (2008) in order to connect to monitor digitally. I´m sure there were options when Adobe Premiere Pro CS3 was the current version back in 2008. Any ideas?
    Jon

    I have already connected two monitors via a DVI “hub”. So they are up and running fine.
    The hub don´t have any more outputs of any kind. Also I´m not sure if the quality would be good enough for the monitor output.
    Now I also realised that there is no HDMI input on the monitor, only HD SDI.
    Please look at photo here for info on my current graphics card.
    Best,
    Jon
    Fra: RoninEdits <[email protected]<mailto:[email protected]>>
    Svar til: "[email protected]<mailto:[email protected]>" <[email protected]<mailto:[email protected]>>
    Dato: Thursday 19 February 2015 11:40
    Til: Jon Berntsen Huseby <[email protected]<mailto:[email protected]>>
    Emne:  Hardware for Mac Pro early 2008
    Hardware for Mac Pro early 2008
    created by RoninEdits<https://forums.adobe.com/people/RoninEdits> in Hardware Forum - View the full discussion<https://forums.adobe.com/message/7209429#7209429>

  • Using Windows Acrobat X as an Upgrade for Acrobat Pro XI for Mac

    Would Acrobat Standard X key for PC work as an upgrade for Acrobat Pro XI for Mac?

    Hi ,
    Adobe Acrobat 11 STD is not available for MAC i.e you can not do upgrade of adobe acrobat 10 std windows to adobe acrobat 11 std for mac

  • Thoughts on Inateck 4 Ports PCI-E to USB 3.0 Expansion Card for Mac Pro (Early 2008 to 2012 Late Version)

    Anyone adding USB 3 ports to the older Mac Pro desktop towers?
    I looked at HighPoint, Orinico and StarTek but I'm leaning towards Inateck given their recent PCI-E board update specifically for Mac Pro.
    Anyone have any USB 3 recommendations or horror stories?  I've got all 4 internal drive bays taken so I don't think I can easily get power to the board, so I'm hoping the internal PCI-E power will be enough for most USB 3 devices.
    thanks,
    Stephen

    There is one that seems to be popular that works with 10.8.2 and above.
    http://forums.macrumors.com/showthread.php?t=1501482&highlight=usb3+pcie

  • Mac Pro 2008 won't boot from install disc - black screen

    Hello,
    I recently purchased a new hard drive to replace the original that came with my Mac Pro 2008.  I was able to format the new drive using Disk Utility. I am now at the point where I need to install OS X onto the new drive, but the computer refuses to boot from the disc. The disc is recognized by the computer (I can access the disc and am able to use the BootCamp applications, etc.) but I just get a black screen when trying to boot directly from the disc. The computer boots fine otherwise.
    I have tried the following:
    I have tried using both the gray install disc that came with the computer and the Snow Leopard Install DVD disc.
    I have tried booting using the "C" key and the "option" key but still receive a black screen following the chime (I've held these down for several minutes).
    I have tried restarting from either install disc using the Bootcamp Assistant.
    I have tried running the installation software to get it to restart from the disc.
    I have tried a combination of the drives, i.e. trying to boot from the discs with just the new drive installed, just the original drive installed, and with both in bay1 and 2.
    Everything results in the computer starting up, hearing the chime, and then nothing..just black screen. I have the original drive partitioned with BootCamp with OSX Snow Leopard and Windows 7 installed (I don't know that that matters).
    I am at a loss as to what to try next. It doesn't seem like the superdrive because it is recognizing the disc, it just won't boot from it.
    Any help is appreciated, thank you.

    Clone should be a must  and easy to do and learn (learn by doing! 2)
    6800 would 'qualify' as 5x70 series flashed etc and same rule: 10.6.5
    In the past there was 10.4.6, 10.5.6, but not 10.6.6 - even though strong need for such a DVD.
    10.6.8 DVD would  be excellent
    Lion or ML - buy, download, make an installer flash card would be what I would do at this point.
    Then keep both - dual boot as you learn and test and see what ML does and waht you had that required Rosetta to support PowerPC. See www.roaringapps.com about that.
    With Carbon Coyp Cloner - was share, now commercial, great utility been around since 10.2.2 at least - this time 2003. 10 yrs.
    You can clone the system folders, you can even selectively choose. You can skip copy of most of your home account and do that separately to another drive if  you want.
    Clone Windows with Paragon or WinClone and use Windows 7 or 8 DVD to do a system repair (automatic) or to edit the BCD file. It can and should - and all you do is boot Windows 7 DVD w/ only the one drive present and go at it. Piece of cake. But yes, Windows gets fussy if you change or remove or move. BCD to the rescue. A proper program for cloning like Paragon's "Clone OS" meant for going from disk drives to SSDs, knows that and how to do it.
    Back to how to clone etc:
    Clone
    Disk utility has RESTORE which will also clone your system but not the Lion Recovery partition. Oddly  Apple did not 'endorse' making bootable clone of the system which works too but most choose Carbon Copy Cloner - it works more consistently; it allows for smart update of the backup volume. Both can backup to a sparse disk image if desired.
    Using Cloning as a Backup Strategy
    http://www.macupdate.com/app/mac/7032/carbon-copy-cloner 
    http://www.bombich.com/software/updates/ccc-3.5.html
    OS X Lion Install to Different Drive
    How to create an OS X Lion installation disc MacFixIt
    Migration Assistant Update for Mac OS X Snow Leopard
    http://www.apple.com/support/lion/installrecovery/
    Create an OS X Lion Install disc
    http://reviews.cnet.com/8301-13727_7-20080989-263/how-to-create-an-os-x-lion-ins tallation-disc
    How to clone your system:
    http://macperformanceguide.com/Mac-HowToClone-backup.html
    http://macperformanceguide.com/Mac-HowToClone.html
    http://www.macupdate.com/app/mac/7032/carbon-copy-cloner
    http://www.macperformanceguide.com/blog/2012/20120711_2-MacPro-internal-clone-ba ckup.html
    The DVD is dependent on your hardware. And your hardware changed. The drivers for the 5780 and 6xxx are bundled in the OS and lacking. Minimum build thing.
    Put the new drive anywhere you want. Does not matter. Can move it later. Can be drive bay 0-3 or a Firewire external or under the DVD drive.
    When you clone pull the old drive and boot from the newly cloned.
    After that keep a backup clone around all the time. Takes less than 10 minutes to do a smart update to copy just the changes to keep it current. So you have working copy of the system. I keep Clone "A" that I keep "as was" the system as of last month or whatever (like 10.7.4 before upgrade to 7.5).
    Comes easier after doing it once and have all your ducks in a row.

  • Mac Pro 2008 Can't start Windows 7 / 8 Installer

    I'm trying to load Windows 8 (And have previously tried everything with Windows 7) on my Mac Pro early 2008 with Mountain Lion, and cannot get the installers to initiate.
    When I start the bootcamp assistant and reboot, my mac freezes before ever getting to the installer. When I reboot and hold option to manually select the installer, it freezes as soon as I select it. I've tried this from a DVD, USB, and even an install partition i setup on my HD, all with the same freezing results. This is a legitimate copy of Windows 8 system builder I'm working with and have installed it perfectly in Parallels.
    I should note I upgraded my video card a long time ago to a gt 120, so I'm wondering if the video card might be the problem. I've installed Windows 7 with this video card in the past so I'm guessing this is a Mountain Lion/Bootcamp 5 issue.
    Has anyone else with a Mac Pro 2008 succesfully installed Windows 7/8 from Mountain Lion/Bootcamp 5?
    Any input would be immensely appreciated!

    There are no Windows 8 Bootcamp drivers. Windows 8 is not supported.
    Use Parallels or Fusion to install Windows 8. By doing so you eliminate the need for drivers since the virtual machine creates virtual hardware and drivers.
    Once the Windows 8 Bootcamp drivers are developed and released you can then install using Bootcamp Assistant.
    Read this forum. Some people are posting that they had some success with the Bootcamp install. but if you have to rely on your computer then don't take the chance.

Maybe you are looking for