Internet sites server architecture

Can anyone guide me with server architecture for SP internet sites.
We are planning for 15000 users. Using FBA authentication with minimum service applications.

Convincing them is relatively straight forward. You just need to point them at a sufficiently definitive source to change the question from 'I don't believe that SharePoint requires AD' to 'That's awkward, why didn't they make it work without AD, that's
a pain'*
The permissions needed for SharePoint installation are listed here and AD is heavily implied, even if they didn't state anything that basic explicitly:
http://technet.microsoft.com/en-us/library/cc678863.aspx
Another thread with the same answer:
http://social.technet.microsoft.com/Forums/sharepoint/en-US/d6924577-e95b-4751-93fb-870741ce2426/active-directory-required-for-sharepoint-2013?forum=sharepointadmin
A thread stating the same from an MVP (Trevor Seward):
http://social.technet.microsoft.com/Forums/sharepoint/en-US/3999d546-946d-47ff-8f8d-8860c84a43b8/sharepoint-2013-and-authentication?forum=sharepointadmin
*It is a pain that AD is required, on the other hand removing that is like taking a card out of the bottom layer of a very large and elaborate house of cards. Or perhaps just taking out the table that the entire stack sits on.

Similar Messages

  • Sharpoint 2010 architecture for internet sites..

    Hi,
    we are trying to build a new fresh sharepoint  2010 farm for internet sites(not intranet). Can some one please help me know what needs to be considered when creating a fresh sharepoint 2010 farm for internet based sites.
    Cheers,
    Kotamarthi Veera

    Refer to this post on design recommendations to create a internet facing SharePoint site
    http://technet.microsoft.com/en-us/magazine/gg457886.aspx
    http://designshare.wordpress.com/2012/11/14/internet-facing-sites-with-sharepoint-2010-tips-tricks-gotchas/
    --Cheers

  • Unable to open this Internet site. The requested site is either unavailable or cannot be found. Please try again later.

    Hi,
    I am in big problem. I had deployed a web application on IIS 7.0 which have windows server 2008 r2 installed. We have some reports in web application. Everything is working fine in web application except when I export content feom SSRS reports to PDF or CSV
    format then I am getting following message
        Unable to open this Internet site.  The requested site is either unavailable or cannot be found.  Please try again later.
    This message comes only on IE8 as I had installed Mozilla but that issue is not coming on Mozilla. I don't why this issue is coming and how to solve this issue. I had gone with every possible results which I found in google but noting seems to be helpful. Please
    help me as it's urgent and I am deploying on production server.
    Thanks...

    Hi Awadhendra,
    This error usually occurs if IE is configured with the "Do not save encrypted pages to disk" advanced options setting or the server is using Secure Sockets Layer (SSL) and has added one or both of the following HTTP headers to the response message:
    e.g: Response.AddHeader "Cache-control: no-cache" or “Cache-control: no-store”.
    To solve this issue, please try to cancel the “Do not save encrypted pages to disk” option in the advanced internet options or setting the “BypassSSLNoCache” registry. For more details, please refer to
    KB323308 .
    Regards,
    Fanny Liu
    Fanny Liu
    TechNet Community Support

  • Is there a way to avoid having a content library on a site server when the Distribution Point role is not installed on that server (disk cost issue)?

    Hello,
    I don't think it is possible, but my goal is to start a discussion about content libraries and maybe suggest something for a future release or version of Configuration Manager.
    Actually, based on Configuration Manager Technet documentation, Configuration Manager creates a content library on each site server and on each distribution point.
    Often, when designing the architecture, people will offload the distribution point role from the site server to an external server (and add the role to other servers too for redundancy). They could also do the same for the Management Point role, but this
    is not related to content library. The idea is to save the site server from having to deal with clients for software distribution (applications, software updates, OS, etc.), this is especially true for organizations having a large number of clients and/or
    primary site servers involved in a hierarchy. Doing so will allow more resources on the site server to deal with the database and also replication in the case of a hierarchy.
    When doing that, you still have to maintain a content library on the site server and the thing is this library will usually become huge, especially for organizations having more than 1000 applications (add also OS images to this). Will the content library
    on the site server become as huge as the one for a distribution point having a copy of all content? I guess the answer is yes.
    I know that Pull distribution points will help offloading the task from the site server to distribute content to distribution points, but, correct me if I'm wrong, you still have to maintain a content library on the site server when using them, and they
    will not make the content library smaller on the site server. Also, I don't like the fact that you lose the rate limits feature with Pull DPs, but this is another story.
    Storage cost is high and in this scenario, it hurts to have to pay this cost for a content library not used by the clients, but only to distribute content to DPs.
    Correct me if I'm wrong, but the key component here is Distribution Manager on the site server; this is the one which has to maintain a content library to do its job.
    It would be nice if we could have a way to elect a specific distribution point (not on the site server) as the Distribution Manager for a site, that main DP would hold a copy of all content by default, but would be used to distribute content to other DPs
    and avoid the content library on the site server. Said differently, the Distribution Manager component would become a site system role that could be transferred outside the site server.
    Tnx for comments, answers or suggestions.
    Patrick

    There is no way to avoid that the contentlib will be placed on the site server.
    I don‘t agree that storage cost is high. It might be true for fast storage, but that‘s not needed for it.
    Torsten Meringer | http://www.mssccmfaq.de

  • Is there a way to change an existing SCCM 2012 site server intranet FQDN name to lowercase?

    Does anyone know if there is a way to change the intranet (not internet) FQDN name of an existing SCCM 2012 site server to all lowercase letters?  You used to be able to do this in SCCM 2007.

    I had a problem with WSUS updates not working via SCCM 2012 R2 during an operating system deployment. When examining the c:\Windows\WindowsUpdate.log I found the following errors:
    WARNING: SendRequest failed with hr = 80072ee2. Proxy List used: <****:8080;****:8080> Bypass List used : <(null)> Auth Schemes used : <>
    + Last proxy send request failed with hr = 0x80072EE2, HTTP status code = 0
    WARNING: GetConfig failure, error = 0x80072EE2, soap client error = 5, soap error code = 0, HTTP status code = 200
    After a LONG time researching this error I found it was related to the fact we were using a WPAD proxy implementation and apparently this doesnt cope well with uppercase characters for the WSUS server URL. I changed our GPO to be using lowercase lettering
    but when examining the WindowsUpdate log again it still showed as being in uppercase. In the end I found that despite what your GPO setting says, this can get over written by the SCCM site server's own published WSUS location. You can check this by entering
    the following command:
    wmic /namespace:"\\root\CCM\SoftwareUpdates\WUAHandler" PATH CCM_UpdateSource
    Unfortunatelty in SCCM 2012 there is no GUI way to amend the intranet FQDN used for the WSUS location so I then turned to directly editing the database (which anyone will tell you is not recommended, but by this point i was DESPERATE!).
    In the end it solved all my troubles so if anyone finds themselves in this situation, you can fix it by going to the SCCM database and within the table 'WSUSServerLocations', change the WSUSServerName to be in lowercase letters.

  • Patches not visible in SCCM 2007 Site server even after approving the patches in WSUS

    Hi,
    The patches are not appearing in SCCM 2007 site server after approving the same patches in WSUS.
    Below are the patches.
    MS14-080: Cumulative Security Update for Internet Explorer - Windows Server 2008 SP2 - IE 7 - KB3008923 [23,186.1]
    MS14-018: Cumulative Security Update for Internet Explorer - IE 11 - KB2929437 - Windows Server 2008 R2 SP1 (x64) [4,32.4]
    MS14-066: Vulnerability in Schannel Could Allow Remote Code Execution - Windows Server 2008 SP2 - KB2992611 (x64) - V2 [1,8.3]
    MS14-038: Vulnerability in Windows Journal Could Allow Remote Code Execution - Windows Server 2008 SP2 - KB2971850 [1,8.1]
    MS09-060: Vulnerabilities in Microsoft Active Template Library (ATL) ActiveX Controls for Microsoft Office Could Allow Remote Code Execution - Visio Viewer 2007 SP1/SP2 [1,8.1]
    MS12-001: Vulnerability in Windows Kernel Could Allow Security Feature Bypass - Windows Server 2008 R2 Gold (x64) [1,8.1]
    MS14-033: Vulnerability in Microsoft XML Core Services Could Allow Information Disclosure - Windows Server 2008 SP2 - KB2939576 [1,8.1]
    MS14-025: Vulnerability in Group Policy Preferences Could Allow Elevation of Privilege - Windows Server 2008 SP2 - KB2928120 (x64) [1,7.8]
    MS13-014: Vulnerability in NFS Server Could Allow Denial of Service - Windows Server 2008 R2 Gold/SP1 (x64) [1,7.7]
    I have approved the above patches in WSUS and ran syncronization. The log wsyncmgr.log show that synchronization is done and even all child sites are syncronized. But I am unable to find the above even in the parent site. Checked all the SUP settings and
    all the 2008 server updates are set and marked to download.
    Please help me out on fixing this.

    So you should NEVER approve anything in WSUS. This will cause problems with your clients. Honestly since you approved things in WSUS, I would uninstall WSUS and reinstall it, reinstall the SUP, this will clear up any issues that now exist.
    Garth Jones | My blogs: Enhansoft and
    Old Blog site | Twitter:
    @GarthMJ

  • How to block an Internet Site.

    There are some Internet site that automaticaly get into my sistem.
    I want to blokout some of these.
    How will I do that.

    localhost is your own computer. It looks like the CRM application is running on your computer and you access it via port 81. So essentially, all the information that you're sending via Firefox is being sent to the application and then presumably, the application is making its own connection to the server.

  • Users unable to access the internet sites

    Hi Everyone,
    We have users who are able to get the IP address but unable to access any internet sites.
    I check the trap logs on the WLC
    RADIUS server 192.168.50.1:1812 failed to respond to request (ID 16) for client 88:53:2e:99:24:b5 / user 'unknown'
    RADIUS server 192.168.50.1:1812 activated on WLAN 1
    RADIUS server 192.168.60.1:1812 deactivated on WLAN 1
    RADIUS server 192.168.60.1:1812 failed to respond to request (ID 200) for client 88:53:2e:99:24:b5 / user 'unknown'
    RADIUS server 192.168.60.1:1812 activated on WLAN 1
    RADIUS server 192.168.50.1:1812 deactivated on WLAN 1
    RADIUS server 192.168.50.1:1812 failed to respond to request (ID 15) for client 88:53:2e:99:24:b5 / user 'unknown'
    RADIUS server 192.168.50.1:1812 activated on WLAN 1
    RADIUS server 192.168.50.1:1812 failed to respond to request (ID 16) for client 88:53:2e:99:24:b5 / user 'unknown'
    RADIUS server 192.168.50.1:1812 activated on WLAN 1
    RADIUS server 192.168.60.1:1812 deactivated on WLAN 1
    RADIUS server 192.168.60.1:1812 failed to respond to request (ID 200) for client 88:53:2e:99:24:b5 / user 'unknown'
    RADIUS server 192.168.60.1:1812 activated on WLAN 1
    RADIUS server 192.168.50.1:1812 deactivated on WLAN 1
    RADIUS server 192.168.50.1:1812 failed to respond to request (ID 15) for client 88:53:2e:99:24:b5 / user 'unknown'
    RADIUS server 192.168.50.1:1812 activated on WLAN 1
    Need to know  how can i troubleshoot this further?
    Regards
    Mahesh

    I would do the troubleshooting in  following sequence.
    1. Put a wired PC on to the vlan allocated for WLAN1
    2. Check whether wired PC gets an IP & can browse internet
    3. If that works, then we know no issue of DHCP & not issue with L3/NAT routing to access internet
    4. If step2, does not work then your issue is not within wireless, you have to change the focus of your troubleshoot.
    5. If step2 works, then test a wireless client with OPEN Authentication (No ACS involvment).If this does not work,then it means wireless client does not get proper IP connectivity. Check dynamic interface configuration for this WLAN & make sure gateway addresses correctly configured. Also VLANs are trunk across to WLC from switch.
    6. If step5 works, then try your client with ACS & see the client get successfully authenticated. If not it may be WLC to ACS issue. Troubleshoot that in that case.
    Do some troubleshooting like this & let us know the outcome. I am sure you will abe to find out the issue easily in this way.
    HTH
    Rasika

  • How long is it to implement JSSE on a client-server architecture?

    Hi all of you,
    Since I'm not a developper but more a system admin, I'm wondering how long approximatly it would take to adapt an existing JAVA client-server architecture to use JSSE or SSL communication over the internet. Is it a simple task or are we talking about weeks of work? Where would be installed the SSL certificate, on the web server or the database server? In brief, what are the main steps that a developper has to go through?
    Architecture:
    JAVA client
    Web server (RMI server), Microsoft IIS5.0
    Database server (MySQL4.0)
    Thanks you all for your precious time,
    AD

    If your webserver has a server certificate from one of the "Big Boys" in the CA business, and if you don't need client-authentication (and almost no-one does) - in your client, write "SSL" in front of everywhere the app currently has the word "Socket", and scratch out "HttpUrl" and replace it with HttpsUrl,." and change your access-urls to start with "https:" and change your socket-connections to talk to your server's SSL port, and you're done. I've taken a Socket-based app and made it SSL/Plain bilingual in two hours once (admittedly, it was a small and well-designed app).
    If your server-cert isn't signed by a known CA, then you have to play some games to get the client side to accept it - but they've all been discussed to death in this forum.
    Grant

  • Access to certain internet sites/services not working

    A couple of days ago, my access to certain internet sites as well as my Mail programme and another email client app stopped making successful connections. I can open many web pages, but some do not work. Specifically, the local library where I can login to check the online catalogue doesn't work. My Mail app won't connect either. I also use another email app called First Class for work and it can't connect to the online server. If I start up Network Diagnostics and change from Airport or Built-in Ethernet it will work, at least until I quit the app and reboot it, then it can't make the connection. I have checked and replaced cables, removed the Airport and gone direct with Built-in Ethernet, etc. This phenomenon happens with all five user accounts on the computer. Other computers in our home which are connect to the LAN have no such behaviours happening, which leads me to conclude something is not right on the iMac we use all the time.
    Any ideas?

    Hi Dennis, and welcome to the Discussions!
    My guess at this point is that you should drag these files to the Desktop for possible later replacement should it not work, then reboot & setup Networking/Internet again...
    /Library/Preferences/SystemConfiguration/preferences.plist
    /Library/Preferences/SystemConfiguration/com.apple.airport.preferences.plist

  • Internet Commerce Server 3.0

    I am trying to install Oracle Internet Commerce Server 3.0 with
    Oracle Web Application Server 3.0, but unable to do so. Please
    the Product Team of Developer 6.0 inform the Internet Commerce
    Server Division to mail me with the Following Info:
    1. Can I install the ICS server with Oracle Application Server
    If no Why Note ?
    If Yes Then where is the documentation and installation files
    and steps
    2.Please give me one of the Product Developers Telephone No,
    Email ID, Fax Numbers
    So that He can solve my problems
    Oracle as a Company has made this excellent product ICS 3.0 but
    the otn site does not have any links for ICS in the Products
    section Nor could I find an E-mail ID to whom I can send my
    questions regarding the same.
    Waiting for some response from the Development Team
    My Tel No is 6212842, 8774899
    null

    Just wanted to offer some further tidbits...
    Came in ealry this monring, turned server on and kapow all clients unable to access internet. Checked server DNS settings as server can access the internet. Double checked clients DNS and all are the same.
    So, turned DNS server off/on and then splatted the dns records. Restarted server with DNS off and still the same thing.
    Staff started to arrive so had to cut it short but it seems very odd that until the upgrade all was well.
    Cheers,
    Stu

  • When I seek to download an Internet site all that arrives is a blank screen with the word'Done' at the bottom please respond to desevans@***

    I am having trouble accessing Internet sites--especially if I want to move from a downloaded site to a link within it. All I get when seeking to dowload is a blank page and the word Done at the sceeen's foot.
    There is also some kind of message in the tool bar referring to 'gif'
    What can I do to improve this?
    I have downloaded the Beta 4 version in the hope that it might have resolved this issue, but the same thing occurs.
    Any help gratefully received. Des Evans
    Desevans

    A possible cause is security software (firewall) that blocks or restricts Firefox without informing you about that, possibly after detecting changes (update) to the Firefox program.
    Remove all rules for Firefox from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox and the plugin-container process.
    See [[Server not found]] and [[Firewalls]] and http://kb.mozillazine.org/Firewalls
    Which security software (firewall) do you have?
    Some firewalls like Kaspersky can block content and send a 1x1 GIF image instead.<br />
    Kaspersky": "Protection > Firewall > Filtration system: disable the "Banner Ad Blocker"<br />
    See [[Configuring Kaspersky Internet Security]] and [[Firewalls]]

  • Unable to open internet sites

    Since yesterday, when trying to open some internet sites, using either Safari or Firefox, I get the same message:
    404 Not Found
    The requested URL /blog/reinaldo/ was not found on this server.
    Apache/2.2.3 (CentOS) Server at veja.abril.com.br Port 80
    Happens with some other sites too.
    Anybody experiencing the same problem?

    I am also having problems open certain sites since yesterday, but they DO open in a PC... just don't in Mac, either my Mac Pro or my Mac Book Pro. I tried all browsers Safari, Firefox, and Chrome. These are some of the sites with issues:
    http://www.yogaglo.com/
    https://www.amazon.com/gp/css/homepage.html?ie=UTF8&ref=topnavya
    and yesterday I was having issues with Hotmail as well and I am seeing a lot of people are having the same problems with other sites.

  • I'm trying to read some XML data from temperature logger over my network. I'm using LabView version 2009 sp1. I'm using the URL Get Document Vi. It works fine when using Internet sites like google or foxnews etc...

    I'm trying to read some XML data from temperature logger over my network.  I'm using LabView version 2009 sp1.  I'm using the URL Get Document Vi.  It works fine when using Internet sites like google or foxnews etc...
    When I use it with my temperature logger most of the time I get an Error 66...but some times it does work and actually retrieves the document. 
    I can use the same address "http://172.22.21.68/XMLfeed.rb" (Internet Explorer or Google Chrome) in my browser and get a response every time.  When accessing from my browser the server in the temperature logger does take around 6 seconds to respond, but it does respond every time. 
    Is the URL Get Document Vi exceeding a timeout?  If so, where can I set it to wait longer?
    Attachments:
    Error 66.jpg ‏183 KB

    It looks like the TCP Buffered Read has a 2.5 sec timeout, I believe that is where I had trouble as well.  Try creating your own URL Get HTTP Doc vi in which you call URL Get Document in normal mode, with an appropriate number of characters to fetch (enough characters so that you capture all the important data in the XML file).
    Attachments:
    ex1.PNG ‏33 KB

  • AirPort can't connect to Internet or Server

    Hello everyone!
    My mac's wireless was working more or less fine until 2 days ago, when suddenly it couldn't connect anymore. I know it's not a problem with the wireless connection itself, because we have 2-3 other computer connecting to it without any problems. When I go through the diagnostics, everything is indicated as green except Internet and Server, which often fluctuate between green, yellow and red.
    I've had a browse for similar problems, and came across this discussion here: https://discussions.apple.com/thread/3044354?start=0&tstart=0
    I followed the advice there and checked whether or not my mac could connect to specific IP addresses of websites, which it can. But other, normal internet addresses, it can't. However, the replier didn't give any concrete solution to the problem (or I just didn't understand it), so I made a new discussion page. If you have any suggestions, please help. I'm out of ideas.
    Thank you!

    Please try each of the steps that follow, in order, until resolved:
    STEP 1
    Create a New User Account
    System Preferences > Accounts
    Click "+" to add a new account
    Log off, and then, log back on with the new user account.
    Try connecting to a Wi-Fi network with your Mac's AirPort.
    STEP 2
    Delete Preferred Network(s)
    System Preferences > Network > Select AirPort > Advanced > AirPort tab
    Under Preferred Network, use the minus button to delete the network(s) you regularly use from the list
    Delete AirPort Keychain Entries (Note: only applies if you connect to AirPort/Time Capsule routers)
    Launch the "Keychain Access" application located in /Applications/Utilities
    Click on the "Kind" filter at the top, and look for any "AirPort network password" entries...and delete them.
    Restart, or log out then back in.
    Add Preferred Network(s)
    System Preferences > Network > Select AirPort > Advanced > AirPort tab
    Under Preferred Network, click on the plus button to add any preferred network(s).
    Restart or log out then back in.
    STEP 3
    Disable the Mac OS X Firewall
    System Preferences > Security > Firewall
    Click the "Stop" button.
    STEP 4
    Move System Configuration Files
    (Note: You will have to reestablish your network connections settings.)
    Go to Macintosh HD/Library/Preferences
    Move (not copy) the SystemConfiguration folder to the desktop.
    Restart your Mac. (Note: OS X will rebuild the folder that are now sitting on your desktop. If this doesn't resolve the issue, you can move the folder back to their original location.)

Maybe you are looking for

  • My built in isight pictures have a red hue!?

    When the isight is in use in any program the image is red. there are no filters on and have tried it in different programs, and all the same result reddish pictures. Can anyone help?

  • OAF page is not able to display the custom error messages

    Hi, I have extended a seeded CO and trying to throw few custom error messages. It was working fine, but suddenly it is not able to display the error messages(but checked that the error messages are still present in application) and saying "Message no

  • ITAB_ILLEGAL_SORT_ORDER dump in CIC searching for Opportunities

    Hi All, We currently have a strange problem when trying to search for opportunities in the CIC.  We go in, enter a partner number and select it as the main partner.  Then, we chose Opportunity as the object to find, enter a date range and click on st

  • Apache with Tomcat and dispatcher class.

    I have a MVC design set up with a controller and dispatcher class. I am trynig to forward the results to a specific JSP. If I run the design completely within Tomcat, then everything works great. I have a tomcat site set up called /jsp. My servlet is

  • Result row at the end of the 2layouts

    Hi All We have 2 layouts in Web Interface builder. we have to calculate the values of 2 layouts and result will come into bottom line. Ex: in layout 1 the value is 3000      in layout 2 the value is -3000 under these 2 layouts i need to get a result