ISDN and CUBE on 2800 Router

Hi All,
Has anyone had any experience with running ISDN and SIP on the same router. I know you can do it on a 2911, just wondering if anyone has it working.

I assume ISDN as in a PRI or BRI and a SIP CUBE aspect as well.
Answer is yes it is working fine.

Similar Messages

How Do I Configure A WRT54G to Work With A Cisco 2800 Router

I'm helping my dad set up a new network. He has a Cisco 2800 series router that connects to the internet via two T1 lines. From this connection, he supplies internet service to his customers. The router was installed and configured with help from AT&T who monitors the router and advises my dad if there are problems.
The Cisco 2800 is not my reason for posting.
He wants to connect his home computers to the 2800. He has one desktop and two wireless laptops and wants to use a WRT54G to connect those computers to the 2800 router. How should he configure the WRT54G to connect to the 2800?
Thanks!

That's what I thought. So it is really no different than connecting the WRT to a DSL modem or cable modem as far as the setup goes. Good then.
Now, next question;
Would this network setup be correct?
Connect a 5-port switch to the 2800
Connect the WRT54G to the 5-port switch.
Configure the laptops to connect throught the WRT54G.
Connect the desktop (Ubuntu 9.10) to the 5-port switch via Ethernet cable (bypass the WRT54G).
Would there be IP conflicts or domain problems? I ask this because this is how his LAN is presently setup and he seems to be getting random connectivity problems on his Ubuntu desktop machine. One day it works fine. The next day it won't connect. Sometimes, even after he is connected, it stop works midstream. It also takes 10 minutes or so to boot up. The laptops always work without issue.
The two laptops would be issued IP addresses of 192.168.1.xxx but the desktop would be getting 12.83.xxxx.xx(something similar). The desktop's internet IP would receive its internet IP from the 2800 via DHCP just like the WRT54G is receiving its IP from the 2800. The two would essentially be on different LANs connected to the same router. Do you forsee any issues here?
Thanks!

ISDN and FRAME-RELAY

Hi All,
I currently have two 2500 routers, to get my hands dirty on ISDN and FRAME-RELAY experiments do i need seperate routers for them?. Because i cannot see where to connect to in regards to the required connections i.e.
2 x Asynchronous/Synchronous Serial Interfaces (DB60)
4 x Serial Interfaces (DB60)
1 x ISDN Interface (RJ45)
1 x Token Ring interface (DB9 and RJ45)
THat i normally hear about when refering to ISDN or FRAME RELAY.
Somebody please put me through.
Secondly i would like to connect my 2500 to the internet ...please put me through how.
Many thanks in Advance

Olu
There are some challenges in what you want to do with this equipment. If each router has 1 x ISDN interface then you can use that for ISDN - but you will need some other piece of equipment to furnish the ISDN switch functionality. You can not just connect 2 ISDN interfaces back to back.
You would be able to do some testing of Frame Relay if you connected the routers back to back - if one of the cables is a DCE cable and one cable is a DTE cable. The testing that you can do with 2 routers back to back is somewhat limited. You could do much better testing if you had a third router which could be configured as a frame relay switch.
Connecting your routers to the Internet will be possible if you connect one of the serial interfaces to an Internet Service provider.
The routers have token ring LAN interfaces. Unless you have some token ring MAUs to establish the connections you will not be able to do effective testing using the token ring LAN interfaces.
HTH
Rick

ROLLUP AND CUBE OPERATORS IN ORACLE 8I

제품 : PL/SQL
작성날짜 : 2000-06-29
========================================
ROLLUP AND CUBE OPERATORS IN ORACLE 8I
========================================
PURPOSE
ROLLUP 과 CUBE Operator에 대해 설명하고자 한다.
Explanation
ROLLUP operator는 SELECT문의 GROUP BY절에 사용된다.
SELECT절에 ROLLUP 을 사용함으로써 'regular rows'(보통의 select된 data)와
'super-aggregate rows'(총계)을 구할 수 있다. 기존에는 select ... union select
를 이용해 구사해야 했었던 것이다. 'super-aggregate rows'는 'sub-total'
(중간 Total, 즉 소계)을 포함한다.
CUBE operator는 Cross-tab에 대한 Summary를 추출하는데 사용된다. 모든 가능한
dimension에 대한 total을 나타낸다. 즉 ROLLUP에 의해 나타내어지는 item total값과
column total값을 나타낸다.
NULL값은 모든 값에 대한 super-aggregate 을 나타낸다. GROUPING() function은
모든 값에 대한 set을 나타내는 null값과 column의 null값과 구별하는데 쓰여진다.
GROUPING() function은 GROUP BY절에서 반드시 표현되어야 한다. GROUPING()은 모든
값의 set을 표현합에 있어서 null이면 1을 아니면 0을 return한다.
ROLLUP과 CUBE는 CREATE MATERIALIZED VIEW에서 사용되어 질수 있다.
Example
아래와 같이 테스트에 쓰여질 table과 data을 만든다.
create table test_roll
(YEAR NUMBER(4),
REGION CHAR(7),
DEPT CHAR(2),
PROFIT NUMBER );
insert into test_roll values (1995 ,'West' , 'A1' , 100);
insert into test_roll values (1995 ,'West' , 'A2' , 100);
insert into test_roll values (1996 ,'West' , 'A1' , 100);
insert into test_roll values (1996 ,'West' , 'A2' , 100);
insert into test_roll values (1995 ,'Central' ,'A1' , 100);
insert into test_roll values (1995 ,'East' , 'A1' , 100);
insert into test_roll values (1995 ,'East' , 'A2' , 100);
SQL> select * from test_roll;
YEAR REGION DE PROFIT
1995 West A1 100
1995 West A2 100
1996 West A1 100
1996 West A2 100
1995 Central A1 100
1995 East A1 100
1995 East A2 100
7 rows selected.
예제 1: ROLLUP
SQL> select year, region, sum(profit), count(*)
from test_roll
group by rollup(year, region);
YEAR REGION SUM(PROFIT) COUNT(*)
1995 Central 100 1
1995 East 200 2
1995 West 200 2
1995 500 5
1996 West 200 2
1996 200 2
700 7
7 rows selected.
위의 내용을 tabular로 나타내어 보면 쉽게 알 수 있다.
Year Central(A1+A2) East(A1+A2) West(A1+A2)
1995 (100+NULL) (100+100) (100+100) 500
1996 (NULL+NULL) (NULL+NULL) (100+100) 200
700
예제 2: ROLLUP and GROUPING()
SQL> select year, region, sum(profit),
grouping(year) "Y", grouping(region) "R"
from test_roll
group by rollup (year, region);
YEAR REGION SUM(PROFIT) Y R
1995 Central 100 0 0
1995 East 200 0 0
1995 West 200 0 0
1995 500 0 1
1996 West 200 0 0
1996 200 0 1
700 1 1
7 rows selected.
참고) null값이 모든 값의 set에 대한 표현으로 나타내어지면 GROUPING function은
super-aggregate row에 대해 1을 return한다.
예제 3: CUBE
SQL> select year, region, sum(profit), count(*)
from test_roll
group by cube(year, region);
YEAR REGION SUM(PROFIT) COUNT(*)
1995 Central 100 1
1995 East 200 2
1995 West 200 2
1995 500 5
1996 West 200 2
1996 200 2
Central 100 1
East 200 2
West 400 4
700 7
위의 내용을 tabular로 나타내어 보면 쉽게 알 수 있다.
Year Central(A1+A2) East(A1+A2) West(A1+A2)
1995 (100+NULL) (100+100) (100+100) 500
1996 (NULL+NULL) (NULL+NULL) (100+100) 200
100 200 400 700
예제 4: CUBE and GROUPING()
SQL> select year, region, sum(profit),
grouping(year) "Y", grouping(region) "R"
from test_roll
group by cube (year, region);
YEAR REGION SUM(PROFIT) Y R
1995 Central 100 0 0
1995 East 200 0 0
1995 West 200 0 0
1995 500 0 1
1996 West 200 0 0
1996 200 0 1
Central 100 1 0
East 200 1 0
West 400 1 0
700 1 1
10 rows selected.
===============================================
HOW TO USE ROLLUP AND CUBE OPERATORS IN PL/SQL
===============================================
Release 8.1.5 PL/SQL에서는 CUBE, ROLLUP 이 지원되지 않는다. 8i에서는 DBMS_SQL
package을 이용하여 dynamic SQL로 구현하는 방법이 workaround로 제시된다.
Ordacle8i에서는 PL/SQL block에 SQL절을 직접적으로 위치시키는 Native Dynamic SQL
(참고 bul#11721)을 지원한다.
Native Dynamic SQL을 사용하기 위해서는 COMPATIBLE 이 8.1.0 또는 그 보다 높아야
한다.
SVRMGR> show parameter compatible
NAME TYPE VALUE
compatible string 8.1.0
예제 1-1: ROLLUP -> 위의 예제 1과 비교한다.
SQL> create or replace procedure test_rollup as
my_year test_roll.year%type;
my_region test_roll.region%type;
my_sum int;
my_count int;
begin
select year, region, sum(profit), count(*)
into my_year, my_region, my_sum, my_count
from test_roll
group by rollup(year, region);
end;
Warning: Procedure created with compilation errors.
SQL> show errors
Errors for PROCEDURE TEST_ROLLUP:
LINE/COL ERROR
10/8 PL/SQL: SQL Statement ignored
13/18 PLS-00201: identifier 'ROLLUP' must be declared
SQL> create or replace procedure test_rollup as
type curTyp is ref cursor;
sql_stmt varchar2(200);
tab_cv curTyp;
my_year test_roll.year%type;
my_region test_roll.region%type;
my_sum int;
my_count int;
begin
sql_stmt := 'select year, region, sum(profit), count(*) ' ||
'from test_roll ' ||
'group by rollup(year, region)';
open tab_cv for sql_stmt;
loop
fetch tab_cv into my_year, my_region, my_sum, my_count;
exit when tab_cv%NOTFOUND;
dbms_output.put_line (my_year || ' '||
nvl(my_region,' ') ||
' ' || my_sum || ' ' || my_count);
end loop;
close tab_cv;
end;
SQL> set serveroutput on
SQL> exec test_rollup
1995 Central 100 1
1995 East 200 2
1995 West 200 2
1995 500 5
1996 West 200 2
1996 200 2
700 7
PL/SQL procedure successfully completed.
예제 2-1: ROLLUP and GROUPING() -> 위의 예제 2와 비교한다.
SQL> create or replace procedure test_rollupg as
my_year test_roll.year%type;
my_region test_roll.region%type;
my_sum int;
my_count int;
my_g_region int;
my_g_year int;
begin
select year, region, sum(profit),
grouping(year), grouping(region)
into my_year, my_region, my_sum, my_count,
my_g_year, my_g_region
from test_roll
group by rollup(year, region);
end;
Warning: Procedure created with compilation errors.
SQL> show error
Errors for PROCEDURE TEST_ROLLUPG:
LINE/COL ERROR
12/4 PL/SQL: SQL Statement ignored
17/13 PLS-00201: identifier 'ROLLUP' must be declared
SQL> create or replace procedure test_rollupg as
type curTyp is ref cursor;
sql_stmt varchar2(200);
tab_cv curTyp;
my_year test_roll.year%type;
my_region test_roll.region%type;
my_sum int;
my_count int;
my_g_region int;
my_g_year int;
begin
sql_stmt := 'select year, region, sum(profit), count(*), ' ||
'grouping(year), grouping(region) ' ||
'from test_roll ' ||
'group by rollup(year, region)';
open tab_cv for sql_stmt;
loop
fetch tab_cv into my_year, my_region, my_sum, my_count,
my_g_year, my_g_region;
exit when tab_cv%NOTFOUND;
dbms_output.put_line (my_year || ' '||my_region ||
' ' || my_sum || ' ' || my_count ||
' ' || my_g_year || ' ' || my_g_region);
end loop;
close tab_cv;
end;
Procedure created.
SQL> set serveroutput on
SQL> exec test_rollupg
1995 Central 100 1 0 0
1995 East 200 2 0 0
1995 West 200 2 0 0
1995 500 5 0 1
1996 West 200 2 0 0
1996 200 2 0 1
700 7 1 1
PL/SQL procedure successfully completed.
예제 3-1: CUBE -> 위의 예제 3과 비교한다.
SQL> create or replace procedure test_cube as
my_year test_roll.year%type;
my_region test_roll.region%type;
my_sum int;
my_count int;
begin
select year, region, sum(profit), count(*)
into my_year, my_region, my_sum, my_count
from test_roll
group by cube(year, region);
end;
Warning: Procedure created with compilation errors.
SQL> show error
Errors for PROCEDURE TEST_CUBE:
LINE/COL ERROR
10/4 PL/SQL: SQL Statement ignored
13/13 PLS-00201: identifier 'CUBE' must be declared
SQL> create or replace procedure test_cube as
type curTyp is ref cursor;
sql_stmt varchar2(200);
tab_cv curTyp;
my_year test_roll.year%type;
my_region test_roll.region%type;
my_sum int;
my_count int;
begin
sql_stmt := 'select year, region, sum(profit), count(*) ' ||
'from test_roll ' ||
'group by cube(year, region)';
open tab_cv for sql_stmt;
loop
fetch tab_cv into my_year, my_region, my_sum, my_count;
exit when tab_cv%NOTFOUND;
dbms_output.put_line (my_year || ' '||
nvl(my_region,' ') ||
' ' || my_sum || ' ' || my_count);
end loop;
close tab_cv;
end;
Procedure created.
SQL> set serveroutput on
SQL> exec test_cube
1995 Central 100 1
1995 East 200 2
1995 West 200 2
1995 500 5
1996 West 200 2
1996 200 2
Central 100 1
East 200 2
West 400 4
700 7
PL/SQL procedure successfully completed.
예제 4-1: CUBE and GROUPING() -> 위의 예제 4와 비교한다.
SQL> create or replace procedure test_cubeg as
my_year test_roll.year%type;
my_region test_roll.region%type;
my_sum int;
my_count int;
my_g_region int;
my_g_year int;
begin
select year, region, sum(profit),
grouping(year), grouping(region)
into my_year, my_region, my_sum, my_count,
my_g_year, my_g_region
from test_roll
group by cube(year, region);
end;
Warning: Procedure created with compilation errors.
SQL> show error
Errors for PROCEDURE TEST_CUBEG:
LINE/COL ERROR
12/4 PL/SQL: SQL Statement ignored
17/13 PLS-00201: identifier 'CUBE' must be declared
SQL> create or replace procedure test_cubeg as
type curTyp is ref cursor;
sql_stmt varchar2(200);
tab_cv curTyp;
my_year test_roll.year%type;
my_region test_roll.region%type;
my_sum int;
my_count int;
my_g_region int;
my_g_year int;
begin
sql_stmt := 'select year, region, sum(profit), count(*), ' ||
'grouping(year), grouping(region) ' ||
'from test_roll ' ||
'group by cube(year, region)';
open tab_cv for sql_stmt;
loop
fetch tab_cv into my_year, my_region, my_sum, my_count,
my_g_year, my_g_region;
exit when tab_cv%NOTFOUND;
dbms_output.put_line (my_year || ' '||my_region ||
' ' || my_sum || ' ' || my_count ||
' ' || my_g_year || ' ' || my_g_region);
end loop;
close tab_cv;
end;
Procedure created.
SQL> set serveroutput on
SQL> exec test_cubeg
1995 Central 100 1 0 0
1995 East 200 2 0 0
1995 West 200 2 0 0
1995 500 5 0 1
1996 West 200 2 0 0
1996 200 2 0 1
Central 100 1 1 0
East 200 2 1 0
West 400 4 1 0
700 7 1 1
PL/SQL procedure successfully completed.
Reference Ducumment
Note:67988.1

Hello,
As previously posted you should use export and import utilities.
To execute exp or imp statements you have just to open a command line interface, for instance,
a DOS box on Windows.
So you don't have to use SQL*Plus or TOAD.
About export/import you may care on the mode, to export a single or a list of Tables the Table mode
is enough.
Please, find here an example to begin:
http://wiki.oracle.com/page/Oracle+export+and+import+
Hope this help.
Best regards,
Jean-Valentin

New fields addition to BW 3.5 version ODS and Cube and transport to PRD.

Hi,
We have a scenarion on 3.5 wherein there is a enhancement to ODS and Cube(few new fileds are added), this New ODS also feeds data to Cube. Since we do not had data on Quality system, we had no problem in adding fields to ODS and cube, but now we need transport these changes to Production, In production ODS and Cube has large data. we have few doubts.
1. Shall we need to delete data from ODS and Cube then Transport request to Production server.
2. Is it ok to move transport request without deleting data in ODS and Subsequent Cube in production system
Guys and Gals,
what is your suggestion on this one. WE are in BW 3.5 only. No BI7.
Please revert back.

Hi
you can directly transport that to production.
the image will over write with the existing one and for the new object add , a new table space will be created.
it will not affect the Old data
But in the Cube even if the data is there there is a concept called remodeling
http://help.sap.com/saphelp_nw70/helpdata/en/58/85e5414f070640e10000000a1550b0/content.htm
hope this helps
santosh

Data in DSO and CUBE

Hi Experts
Please..Please update me on in detail if possible with example ......Key Fields and Dimensions
How Data Records will be processed in DSO and Cube
I tried to search but i can't able to find what i am looking for
My Requirment:
I am extracting Employee Benefits records from Non SAP Source System (Oracle Tables)
In the Oracle there is no Date field avaliable and there won't be any history avaliable in oracle once the Benefits of an employee is changed the old record will be overwritten to new one so they can't track the employee benefits history...but in BW i need to store/show history of employee benefits by Cal day
Oracle Table Fields
Location (Primary Key)
Emp No (Primary Key)
Insurance Type
Call Allowance Type
Annual Leave (No of day Days)
Pension Schem
Company Laptop (Yes/No)

hi,
key fields are the primary keys of ur ods tables. based on the key field values the data fields will get overwritten.
suppose if the key fields values were same then the data fields will get overwritten. but the changes were captured in the change log table, hence the history of changes is available.
Dimensions- are the prmary keys of cube. but in cube only addition of records will happen as default not overwrite as in ods.
dimension ids were generated based on the sid values of characteristics.
maximum of 16 key fields and dimensions can be there in ods and cube respectively.
for ur case, include 0calday field in the key fields and use the routine to update the field with system date(SY-Date). this keeps track/ else without date also , change log maintains history for each load.
have to add 0recordmode to the communication structure of the ods(infosource).
Ramesh

Can i use my time capsule as wireless storage and not as a router too?

hi there i just bought my self a time capsule its a 500gb one as i do not need the 1tb+ storage.
i play a lot of online games and have a fast router so i do not want the time capsule for its router capabilitys i only want to use it as a wireless storage unit is this possible to do?
if not i can connect a usb storage to my current router and use that as my wireless storage if so where is the best place to sell this time capsule?

You simply bridge the TC and plug it into the existing router.. it will then provide network storage..
Can connect either via the existing router or the TC.. if you set up wireless correctly.. if it is a gen1 you can set to 5ghz only.. that will keep it from interferring with the existing router.

Can I use my time capsule for back up only and not as a router?

I have been trying to set up my time capsule as a router but have not been successful, the dsl I am using is not responding. Can I just use my time capsule as a back up device and not as a router? if so how can I do this?

Yes, you can. Simply plug the TC via Ethernet into the current router and set it up in bridge mode.

How can i update data of DSO and Cube using ABAP??

Hello Experts
I have a requrement in which i need to update/ delete data from DSO and cube based on certain keys using ABAP.
Please let me know how can i modify contets of cube or active table of DSO.
Thanks
Sudeep

Hi
I have requirement such that i need to update certain key figures in DSO after certain time.
for eg. say record with key a is loaded to DSO and currospoding key figure was loaded with value 10
after few days because of certain parameters changing in system i need to modify key figure value.
currently i am doing same using 1 self transformation i.e. by loading same data again in same DSO.
Amount of data is very huge and causing performance issues in system.
now A is not key but i need to modify record for few combinations which apperar multiple times in DSO.
Same DSO data is loaded into Cube regularly.
I may need to update data after gap of few weeks as well.
This design will be used as template and needto keep whole logic generic.
So wring Function module can make it generic.
Thanks
Sudeep

Wi-fi bridge between two routers TP-LINK WR841ND (WDS). HP 1536 dnf MFP connect to one of this routers (copper). My Ipad or Iphone can't find HP 1536 dnf MFP (using Eprint). Ipad and iphone connect to router across WiFi.

Hello.
I have wi-fi bridge between two routers TP-LINK WR841ND.
The name of this technology - WDS.
HP Laser JET 1536 dnf MFP connect to one of this routers (copper).
Second device (my NETBOOK) connect to second router (WiFi).
I have good communication between NETBOOK and HP Laser JET 1536 dnf MFP via WiFI-bridge.
In usual case NETBOOK can find (and can Ping) network printer and make a print some files.
But my Ipad or Iphone can't find HP Laser JET 1536 dnf MFP (using Eprint). Ipad and iphone connect
to router across WiFi.
Please, help!

Are you using the ePrint Mobile App, the ePrint Printer Control App, or just trying to send an email to the printer's ePrint email address?
Does AirPrint work?
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

How to do reconcilization of ODS data and CUBE data

Hi All,
How to do reconciliation of ODS data and CUBE data,I know how to do reconciliation of R/3 data and BW data.
Regards.
hari

Hi,
create a multicube based on your ODS and cube, identify commen characteristics and perform the key figure selections; create then a query showing both information from the cube and ODS with perhaps some formula showing differences between key figures.
hope this helps...
Olivier.

Is the concept of Transactional DSO and Cube in BI 7?

Hi,
Is the concept of Transactional DSO and Cube in BI 7?
I see 3 type of Cubes[Standard or VirtualProvider (Based on DTP, BAPI or Function Module)]
but canu2019t see transaction Cube.
also
I see 3 type of DSO(Standard, Write-optimized, Direct update )
but canu2019t see transaction DSO
See this link on DSO, with examples etc:
http://help.sap.com/saphelp_nw04s/helpdata/en/F9/45503C242B4A67E10000000A114084/content.htm
I am looking for such summary also for Cubes have you see a similar one?
Thanks

New terminology in BI 7.x
Transactional ODS = DSO for direct update
Transactional Cube = Realtime Cube
Jen

Why do we create indexes for DSOs and Cubes.What is the use of it?

Hi All,
Can you please tell me why are indexes created for DSOs and Cubes.
What is the use with the creation of indexes.
Thanks,
Sravani

HI ,
An index is a copy of a database table that is reduced to certain fields. This copy is always in sorted form. Sorting provides faster access to the data records of the table, for example, when using a binary search. A table has a primary index and a secondary index. The primary index consists of the key fields of the table and is automatically created in the database along with the table. You can also create further indexes on a table in the Java Dictionary. These are called secondary indexes. This is necessary if the table is frequently accessed in a way that does not take advantage of the primary index. Different indexes for the same table are distinguished from one another by a separate index name. The index name must be unique. Whether or not an index is used to access a particular table, is decided by the database system optimizer. This means that an index might improve performance only with certain database systems. You specify if the index should be used on certain database systems in the index definition. Indexes for a table are created when the table is created (provided that the table is not excluded for the database system in the index definition). If the index fields represent the primary keys of the table, that is, if they already uniquely identify each record of the table, the index is referred to as an unique index.
they are created on DSO and cube for the performance purpose ..and reports created on them wil be also more efficent ..
Regards,
shikha

Rollup and Cube

can anyone xplain rollup and cube function in Groupby clause

Google "rollup and cube in oracle" or
http://www.psoug.org/reference/rollup.html
HTH
Girish Sharma

Group and Group counter in Routing

Hi all,
what is group and group counter in routing , how these are used in routing , please explain.
Regards,
Joseph.

Dear Joseph,
1.Each routing is stored against a group and group counter no.
2.When we create routing without respect to any material and only by giving the plant,the set of operations gets saved under one
group counter and group no.
4.Many materials can be assigned to this same group and group counter no,so that the routing is valid for all the materials included.
5.When you create a routing for material specific,the set of operation gets saved in a group no and group counter no as 01,when
you create another routing with another set of operations for the same material,plant and task list combination now the group no
remains same and the group counter gets saved under 02.
6.This data can be further helpful in assigning the routing data in the production version,.
Check and revert
Regards
S Mangalraj

ISDN and CUBE on 2800 Router

Similar Messages

Maybe you are looking for