Loading reiser4 with grub hangs with stage 2

I converted my hard drive to reiser4 and installed the patched graphical grub 0.96-4 from the forums with reiser4 support. After that grub installs with install-grub giving me:
[root@myhost Grub]# ./install-grub /dev/hda /dev/hda7
Install Device: (hd0) /dev/hda
Boot Device: (hd0,6) /dev/hda7
Continue? [Y/n]
Probing devices to guess BIOS drives. This may take a long time.
GNU GRUB version 0.96 (640K lower / 3072K upper memory)
[ Minimal BASH-like line editing is supported. For the first word, TAB
lists possible command completions. Anywhere else TAB lists the possible
completions of a device/filename. ]
grub> root (hd0,6)
Filesystem type is reiser4, partition type 0x83
grub> setup (hd0)
Checking if "/boot/grub/stage1" exists... yes
Checking if "/boot/grub/stage2" exists... yes
Checking if "/boot/grub/reiser4_stage1_5" exists... yes
Running "embed /boot/grub/reiser4_stage1_5 (hd0)"... failed (this is not fatal)
Running "embed /boot/grub/reiser4_stage1_5 (hd0,6)"... failed (this is not fatal)
Running "install /boot/grub/stage1 (hd0) /boot/grub/stage2 p /boot/grub/menu.lst "... succeeded
Done.
grub> quit
Grub installation finished
Then after I reboot the computer hangs giving me grub loading stage 2. How can I fix this problem.
Thanks for the help,
Matt

Well I created a separate boot partition which I would suggest for anybody since grub with reiser4 patches doesn't seem to work so well. In addition it is easier to access the partition with almost any boot cd which is a bonus if you are like me and keep screwing up (I would also say it helps to copy install-grub to boot). It seems until grub 2 comes out either use lilo with reiser4 or create a separate boot if you plan on using grub.
I guess I should also mention that the result could have been due to my particular setup. I didn't think it could be a problem any more especially with grub but my linux partition is towards the end of the drive on a logical partition. This could have something to do with the boot since grub with reiser4 skips stage 1.5 and goes to stage 2 which normal grub doesn't. Naturally I could be saying a lot of wrong things.

Similar Messages

Loading images with different horizontal sizes

I would like to load images with different horizontal
resolutions (vertical resolution to be the same) dymanically into
an empty movie clip. I would like them to load with the right hand
side of the image lined up with the right hand side of my site. I
have seen many tutorials about how to accomplish the loading of the
movies, but I cannot figure out how to make them open with the
right hand side always lined up on the right.
To be more specific, let's say I have three images of the
varying pixel resolutions (1200x600, 800x600, and 400x600 for
example). I would like the horizontal size to always extend away
from the right hand side of the site with the right hand edge of
the images always lined up.
Is this possible to do by loading them into an empty movie
clip?
thanks

When you load an image file into an empty movieClip, that
clip takes on the dimensions of the loaded content. The
registration point for the clip is set to the upper left corner.
So, once the new image is loaded, just set that clip's .x to the
stage width - the width of the clip.

I accidently downloaded something that made my webcam flash on spuradically even once i deleted it. when i restarted my computer it got stuck at the white loading screen with the grey apple and wont go past there..what is wrong? will applecare cover this?

i accidently downloaded something that made my webcam flash on spuradically even once i deleted it. when i restarted my computer it got stuck at the white loading screen with the grey apple and wont go past there..what is wrong? will applecare cover this? my computer also slowed down drastically before it stopped working..thanks! HELP PLEASE!

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
a. Boot into the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
If you've booted from an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
Step 3
Boot in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 5.
If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 4
Sometimes a boot failure can be resolved by resetting the NVRAM.
Step 5
Launch Disk Utility in Recovery mode (see Step 1.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then reboot as usual.
Step 6
Reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 7
Repeat Step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a Time Machine or other backup.
Step 8
This step applies only to older Macs (not current models) that have a logic-board ("PRAM") battery. Both desktop and portable Macs used to have such a battery. The logic-board battery is separate from the main battery of a portable. A dead logic-board battery can cause a gray screen at boot. Typically the boot failure will be preceded by loss of the startup disk and system clock settings. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 9
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested. If you can't get to an Apple Store, go to another authorized service provider.

Since updating to I.O.S7 on my ipad2 all i get when i turn it on is a loading screen with a picture of a charger going into an ITUNES sign? HELP nothing will work not interactive at all?

all i get when i turn it on is a loading screen with a picture of a charger going into an ITUNES sign? HELP nothing will work not interactive at all.aince updating to I.O.S7.0.2???
What should i do currently have it on charge for several hours not done a thing and have been locking and unlocking and resetting

Please see: http://support.apple.com/kb/HT1808 for further info. It sounds like you are already in Recovery mode so if the image in Step 4 is the one you see, skip to Step 5.
Regards,
Steve

Load testing with concurrent users on HTTP Web

Hello,
I am trying to do load testing my PHP Web Application.
I record (with Firefox) and developed the testing script with OpenScript,
but I found that I could only test with "Iteration" feature.
Is there any way to do load testing with concurrent users ( multi users login at the same time ) which defined in databank?
Thanks for help.

Hi
You need to load the script into OLT (Oracle Load Testing) you can download it from here you need the first link Oracle Application Testing Suite and run the OATSxxx.exe to install OLT.
Regards
Alex

Incremental load fails with the error LM_44127 Failed to prepare the task

Guys,
I have created a custom mapping and cretaed a execution plan for this mapping in the DAC. The full load completes successfully. But when ever the incremental lod is run , i am getting the below error and the task fails(The SDE load completes sucessfully , but the SIL load fails with the below error).
LM_44127 Failed to prepare the task
Please help!!!

i googled it..
http://datawarehouse.ittoolbox.com/groups/technical-functional/informatica-l/lm_44127-failed-to-prepare-task-when-running-workflow-in-informatica-86-on-aix-3199309
you can try for better links now.. !!

Data load issue with export data source - BW 3.5

Hi,
We are facing issues in loading data with the help of export data source.
We have created export data source of 0PCA_C01 cube. With the help of this export datasource, we are loading data to other custom cube. Scenario is working fine in development server.
But when we transported objects to quality server data is not getting loaded to custom target cube.
It is extracting zero records. All transports are ok and we have generated export datasource in quality before transports .Also regenerated export datasource after transport and activated infosource, update rule via RS* programs. Every object is active but data is not getting extracted.
RSA3 for 80PCA_C01 datasource isn't extracting any record in Quality. Records getting extracted in development. We are in BW 3.5 with patch level 19.
Please guide us to resolve the issue.
Thanks,
Aditya

Hi
Make sure that you have relevant Role & Authorization at Quality/PRS.
You have to Transport the Source Cube first and then Create a Generate Export Data Source in QAS. Then, replicate data sources for BW QAS Soruce System. Make sure this replicated Data Source in QAS. Only then can transport new update rules for second cube.
Hope it helps and clear

How can I convert my music, and CDs to MP3, for use in my vehicle's AM/FM/ Stereo? I have a 16 GB SDHC Card, that I would like to load up with some of my music.

How can I convert my music, and CDs to MP3, for use in my vehicle's AM/FM/ Stereo? I have a 16 GB SDHC Card, that I would like to load up with some of my music.
Thanks for any help you can furnish.
Ed

Well, this question really belongs in the iTunes forum, which is where you will get fast answers.
Just go to iTunes Preferences. Click on the General icon. Set When you insert a CD to Ask to Import CD. Click on Import Settings. Set Import to MP3 decoder. Make sure you're using Good Quality.
This should deal with your CD's.
With your current music, as long as it does not have DRM restrictions (older iTunes Music did), select the song, right click on the song (or group of songs), pull down to Create MP3 version.

Sql@loader-704 and ORA-12154: error messages when trying to load data with SQL Loader

I have a data base with two tables that is used by Apex 4.2. One table has 800,000 records . The other has 7 million records
The client recently upgraded from Apex 3.2 to Apex 4.2 . We exported/imported the data to the new location with no problems
The source of the data is an old mainframe system; I needed to make changes to the source data and then load the tables.
The first time I loaded the data i did it from a command line with SQL loader
Now when I try to load the data I get this message:
sql@loader-704 Internal error: ulconnect OCISERVERATTACH
ORA-12154: tns:could not resolve the connect identifier specified
I've searched for postings on these error message and they all seem to say that SQL Ldr can't find my TNSNAMES file.
I am able to connect and load data with SQL Developer; so SQL developer is able to find the TNSNAMES file
However SQL Developer will not let me load a file this big
I have also tried to load the file within Apex (SQL Workshop/ Utilities) but again, the file is too big.
So it seems like SQL Loader is the only option
I did find one post online that said to set an environment variable with the path to the TNSNAMES file, but that didn't work..
Not sure what else to try or where to look
thanks

Hi,
You must have more than one tnsnames file or multiple installations of oracle. What i suggest you do (as I'm sure will be mentioned in ed's link that you were already pointed at) is the following (* i assume you are on windows?)
open a command prompt
set TNS_ADMIN=PATH_TO_DIRECTOT_THAT_CONTAINS_CORRECT_TNSNAMES_FILE (i.e. something like set TNS_ADMIN=c:\oracle\network\admin)
This will tell oracle use the config files you find here and no others
then try sqlldr user/pass@db (in the same dos window)
see if that connects and let us know.
Cheers,
Harry
http://dbaharrison.blogspot.com

Unable to load pictures with mac osx..

I was wondering if anyone knows the reason why I'm unable to load pictures with my macbook for e-bay when I sell??? It just keep turning and turning with no results...
Is it the new operating platform (osx) or what could it be?? I have tried it with an older mac, had no problem loading them....
Thanks for comments....David..

Is there an uploader program from ebay that you use? If so, then you might try digging out the preference file from your library/preferences and see if it generates a new, non-corrupt one. If it uses a browser interface and that is stalling, then I'd suggest using a different browser. You can also ask ebay support.

CF 10 Load-Balancing with Remote Instances

I was reading an article on Clustering/LB/HA using CF8, but have not found any updates for CF10.
Using VM VirtualBox to setup a few virtual servers, I am looking to setup a load balancing of ColdFusion 10 on 2 remote instances. The goal would be have ColdFusion Cluster Manager be able to point http request to one of the two servers based on load/availability. Not really having a hardware cluster/failover setup, just managing resources on two CF instances instead of a standalone.
The servers are Windows Server 2008 R2 with IIS7.5 and ColdFusion 10 Enterprise on installed on 3 of these machines. Let's call them CF-LBManager, CF-Web1, and CF-Web 2. In the CF Docs, they show the Cluster Manager adding the local CF instance and "if you want" a remote instance. However, this scenario would require the main instance to be running and not fail for it to direct to the other instance.
I am trying to set this up now with CF-LBManager as just a manager of the requests coming in. In the Enterprise Manager >> Instance Manager, the local instance is shown and I add the two remote instances with the correct Remote Port, JVM Route, etc. I also made sure the <Cluster>...</Cluster> block was added to the two remote instances (CF-Web1 and CF-Web2) \runtime\conf\server.xml file too, Jetty Services also is running. Now under the Enterprise Manager >> Cluster Manager I add the two remote instances to the cluster, not the local instance on CF-LBManager with Multicast Port and Sticky Sessions enabled. On Submit, I get a green message "You must restart all the server instances and any configured webservers for these changes to take effect.". I go ahead and reboot the servers and come back.
I now browse to the ColdFusion page as a test on CF-Web1 and CF-Web2 to make sure CF is running properly, they do. I then browse the IP of the CF-LBManager, however it only returns the local IIS web site and not redirect to one of the two cluster members. I am not seeing any message on the coldfusion-out.log on the remote instances. Am I not setting this up correctly or not enabling the Cluster Manager to take over and pass along the requests to those in the cluster?

Unfortunatley I don't have a lot of experience with CF10 on Windows, but if you are running CF behind IIS I think you will need to update the Tomcat connector configuraiton to do load balancing. I'm not sure if re-running the wsconfig tool on all of the servers will do this or not, but that is what I would suggest trying first. If that doesn't work you will need to update the Tomcat connector configuraiton manually. You can find more information on load balancing with the Tomcat connector here: http://tomcat.apache.org/connectors-doc/generic_howto/loadbalancers.html.

My macbook had a weird behavior on the display, now it won't go further than gray loading screen with the apple logo

My macbook had a weird behavior on the display, now it won't go further than gray loading screen with the apple logo. It's a macbook pro early 2011. I've read that those are having issues, if there's someone i can contact for further information, report the issue since it's getting common or any temporal solution available. Thanks

Reinstall Lion, Mountain Lion, or Mavericks without erasing drive
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported then click on the Repair Permissions button. When the process is completed, then quit DU and return to the main menu. Select Restart from the Apple menu.
Reinstall Mountain Lion or Mavericks
OS X Mavericks- Reinstall OS X
OS X Mountain Lion- Reinstall OS X
Note: You will need an active Internet connection. I suggest using Ethernet
if possible because it is three times faster than wireless.

Where to down load assets with Asset Capitalization date and Book value..

Hi All,
What is table/Transaction code to down load Asset with below details:
1) Capitalization
2) Acquisition value
3) Book Value
4) Book Dep Value
5) Cost center
Thx In advance..
Regards,
Shirisha

You can try the Asset History Sheet report S_ALR_87011990 (which has all fields except for cost center) and if you want additional fields you can choose to add new fields through the link [Include own fields in FI-AA standard ALV |https://wiki.sdn.sap.com/wiki/display/ERPFI/IncludeownfieldsinFI-AAstandardALV] the relevant report for Asset History Sheet should be Asset History Sheet -> FIAA_SALVTAB_RAGITT includes CI_REPRAGITT (out of RAGITT_ALV01). Else a quicker option would be to perform a vlookup process from another report that has cost centers like S_ALR_87011979.

IPhone 5 randomly shuts off and it is stuck at the loading screen with codes popping up

My friend's iPhone randomly shuts down today and the loading screen with the apple logo came on with some codes. I tried restarting it manually but the same thing keeps happening. The codes start with [nand] and mention something about blocks. What could be the problem?

Could be a hardware fault. It may need to be replaced.
Have you tried restoring it?
~Lyssa

SQL Loader Problem with Date Format

Dear all,
I am dealing with a problem in loading data with SQL Loader. The problem is in the date format.
More specifically, I created the following Control File:
file.ctl
LOAD DATA
INFILE 'D:\gbal\chatium.log'
APPEND INTO TABLE CHAT_SL
FIELDS TERMINATED BY WHITESPACE
TRAILING NULLCOLS
(SL1 DATE "Mon DD, YYYY HH:MI:SS FF3AM",
SL2 char,
SL3 DATE "Mon DD, YYYY HH:MI:SS FF3AM",
SL4 char,
SL5 char,
SL6 char,
SL7 char,
SL8 char,
SL9 char,
SL10 char,
SL11 char,
SL12 char,
SL13 char,
SL14 char,
SL15 char)
The data we want to load are in the following file:
Apr 29, 2007 12:05:49 AM 1060615 Apr 29, 2007 12:05:35 AM 306978537730 24026384 chatium.user.userinfo WAP 0
Apr 29, 2007 12:12:51 AM 1061251 Apr 29, 2007 12:12:27 AM 306978537730 24026384 chatium.channel.list WAP 0
Apr 29, 2007 12:12:51 AM 1061264 Apr 29, 2007 12:12:32 AM 306978537730 24026384 chatium.channel.listdetail WAP 0
Apr 29, 2007 12:13:51 AM 1061321 Apr 29, 2007 12:13:31 AM 306978537730 24026384 chatium.user.search WAP 0
Apr 29, 2007 12:13:51 AM 1061330 Apr 29, 2007 12:13:37 AM 306978537730 24026384 chatium.user.userinfo WAP 0
The error log file is the following:
SQL*Loader: Release 9.2.0.1.0 - Production on Mon Apr 30 11:29:16 2007
Copyright (c) 1982, 2002, Oracle Corporation. All rights reserved.
Control File: file.ctl
Data File: D:\gbal\chatium.log
Bad File: chatium.bad
Discard File: none specified
(Allow all discards)
Number to load: ALL
Number to skip: 0
Errors allowed: 50
Bind array: 64 rows, maximum of 256000 bytes
Continuation: none specified
Path used: Conventional
Table CHAT_SL, loaded from every logical record.
Insert option in effect for this table: APPEND
TRAILING NULLCOLS option in effect
Column Name Position Len Term Encl Datatype
SL1 FIRST * WHT DATE MonDD,YYYYHH:MI:SS
SL2 NEXT * WHT CHARACTER
SL3 NEXT * WHT CHARACTER
SL4 NEXT * WHT CHARACTER
SL5 NEXT * WHT CHARACTER
SL6 NEXT * WHT CHARACTER
SL7 NEXT * WHT CHARACTER
SL8 NEXT * WHT CHARACTER
SL9 NEXT * WHT CHARACTER
SL10 NEXT * WHT CHARACTER
SL11 NEXT * WHT CHARACTER
SL12 NEXT * WHT CHARACTER
SL13 NEXT * WHT CHARACTER
SL14 NEXT * WHT CHARACTER
SL15 NEXT * WHT CHARACTER
Record 1: Rejected - Error on table CHAT_SL, column SL1.
ORA-01840: input value not long enough for date format
Record 2: Rejected - Error on table CHAT_SL, column SL1.
ORA-01840: input value not long enough for date format
Record 3: Rejected - Error on table CHAT_SL, column SL1.
ORA-01840: input value not long enough for date format
Record 4: Rejected - Error on table CHAT_SL, column SL1.
ORA-01840: input value not long enough for date format
I wonder if you could help me.
Thank you very much in advance.
Giorgos Baliotis

SQL> select to_date('Apr 29, 2007 12:05:49 AM','Mon DD, YYYY HH:MI:SS FF3AM') from dual;
select to_date('Apr 29, 2007 12:05:49 AM','Mon DD, YYYY HH:MI:SS FF3AM') from dual
ERROR at line 1:
ORA-01821: date format not recognized
SQL> ed
Wrote file afiedt.buf
1* select to_date('Apr 29, 2007 12:05:49 AM','Mon DD, YYYY HH:MI:SS AM') from dual
SQL> /
TO_DATE(
29/04/07
SQL> Then, you defined blank space as separator, but there is spaces in your date inside your file. So, you should add double-quotes around the date field like below, and add optionally enclosed by '"' into your ctlfile.
"Apr 29, 2007 12:05:49 AM" 1060615 "Apr 29, 2007 12:05:35 AM" 306978537730 24026384 chatium.user.userinfo WAP 0
"Apr 29, 2007 12:12:51 AM" 1061251 "Apr 29, 2007 12:12:27 AM" 306978537730 24026384 chatium.channel.list WAP 0
"Apr 29, 2007 12:12:51 AM" 1061264 "Apr 29, 2007 12:12:32 AM" 306978537730 24026384 chatium.channel.listdetail WAP 0
"Apr 29, 2007 12:13:51 AM" 1061321 "Apr 29, 2007 12:13:31 AM" 306978537730 24026384 chatium.user.search WAP 0
"Apr 29, 2007 12:13:51 AM" 1061330 "Apr 29, 2007 12:13:37 AM" 306978537730 24026384 chatium.user.userinfo WAP 0Example :
http://download-uk.oracle.com/docs/cd/B19306_01/server.102/b14215/ldr_concepts.htm#sthref477
Nicolas.

Loading reiser4 with grub hangs with stage 2

Similar Messages

Maybe you are looking for