Managed Server will not start with 2-way SSL enabled
When attempting to start a managed server, using the nodemanager (all of the servers have two-way ssl configured...using the same keystores) the start-up fails, giving the following error:
<Warning> <Security> <BEA-090497> <HANDSHAKE_FAILURE alert received from hostname - ip address. Check both sides of the SSL configuration for mismatches in supported ciphers, supported protocol versions, trusted CAs, and hostname verification settings.>
Hostname verification is off for all of the servers and the trust store should trust the certificate in the identity store.
Is this an issue with the managed server not being able to pass the identity certificate during the handshake?
Thanks in advance for any help!
hi
the following link may hekpful to you
http://webservices.bea.com:8080/Clarify/getCaseDetails.do?caseID=537204
open a support case with bea
Regards
Prasanna Yalam
Similar Messages
-
I have a new WebLogic 10 server and none of the new app servers will start. Gets the message "the Node Manager associated with machine sitportal1 is not reachable.
All of the servers selected are currently in a state which is incompatible with this operation or are not associated with a running Node Manager or you are not authorized to perform the action requested. No action will be performed. " When I check the node manager logs (node manager service IS running) it has the error lsited below. I found this solution but not sure how to check or verify it. *Solution:
It could be that the CA certificates sent to the server are being shown in the wrong order for the chain. Review the CAs and see if the order such as Public, Intermediate, Root CA is respected. *
Any guidance would be appreciated and points awarded. Thanks
Dec 23, 2008 2:46:59 PM> <Warning> <Uncaught exception in server handler: javax.net.ssl.SSLKeyException: [Security:090482]BAD_CERTIFICATE alert was received from 127.0.0.1 - 127.0.0.1. Check the peer to determine why it rejected the certificate chain (trusted CA configuration, hostname verification). SSL debug tracing may be required to determine the exact reason the certificate was rejected.>
javax.net.ssl.SSLKeyException: [Security:090482]BAD_CERTIFICATE alert was received from 127.0.0.1 - 127.0.0.1. Check the peer to determine why it rejected the certificate chain (trusted CA configuration, hostname verification). SSL debug tracing may be required to determine the exact reason the certificate was rejected.
at com.certicom.tls.interfaceimpl.TLSConnectionImpl.fireException(Unknown Source)
at com.certicom.tls.interfaceimpl.TLSConnectionImpl.fireAlertReceived(Unknown Source)
at com.certicom.tls.record.alert.AlertHandler.handle(Unknown Source)
at com.certicom.tls.record.alert.AlertHandler.handleAlertMessages(Unknown Source)
at com.certicom.tls.record.MessageInterpreter.interpretContent(Unknown Source)
at com.certicom.tls.record.MessageInterpreter.decryptMessage(Unknown Source)
at com.certicom.tls.record.ReadHandler.processRecord(Unknown Source)
at com.certicom.tls.record.ReadHandler.readRecord(Unknown Source)
at com.certicom.tls.record.ReadHandler.readUntilHandshakeComplete(Unknown Source)
at com.certicom.tls.interfaceimpl.TLSConnectionImpl.completeHandshake(Unknown Source)
at com.certicom.tls.record.ReadHandler.read(Unknown Source)
at com.certicom.io.InputSSLIOStreamWrapper.read(Unknown Source)
at sun.nio.cs.StreamDecoder$CharsetSD.readBytes(StreamDecoder.java:411)
at sun.nio.cs.StreamDecoder$CharsetSD.implRead(StreamDecoder.java:453)
at sun.nio.cs.StreamDecoder.read(StreamDecoder.java:183)
at java.io.InputStreamReader.read(InputStreamReader.java:167)
at java.io.BufferedReader.fill(BufferedReader.java:136)
at java.io.BufferedReader.readLine(BufferedReader.java:299)
at java.io.BufferedReader.readLine(BufferedReader.java:362)
at weblogic.nodemanager.server.Handler.run(Handler.java:66)
at java.lang.Thread.run(Thread.java:595)Hii
This is a Common Error.
1.Make sure your Admin Server is in Running mode.
2.Make sure that your Managed Server is in shutdown mode.
3.Make sure that your domain mapping is correct.
4.Any domain created before creation of Node Manager Service will not be accessible via node Manager(even after restarting node manager), solution is to run the WLST command “nmEnroll” to enroll that domain with the Node Manager.
Here are the steps to do "nmEnroll".
Example:
cd $BEA_HOME\user_projects\domains\<domain_name>\bin
setDomainEnv.cmd
java weblogic.WLST
wls> connect(‘weblogic’,'weblogic’,
‘t3://mymachine.mydomain:7001′)
wls> nmEnroll(‘C:\bea\user_projects\domains/<domainName>’, ‘C:\bea\wlserver_<version>/common/nodemanager’)
5.Start your Node Manager and look for the logs where it specifies the Domain Mapping Path.
6.Verify the domain path.
7.Now Start your Managed Server. -
Management server will not start
I also can't get management server to start. If I try to start it, I get the 997 overlapped I/O operation error.
I have tried as the answers to other posts on this subject suggest, but nothing has worked. I have created a new repository and saved the user name and password. The service will not start and trying to login with Enterprise Manager gives me an Invalid login error.
Any new suggestions? BTW I am working on a test machine so if I have to wipe and reinstall everything againthat is no problem at all.
Please answer ASAP.I turned up logging and found this. If the server was working before I tried to restart it is this really the problem?
2010-12-29 15:42:15.667 INFO CAD Starting Server Intelligence Agent...
2010-12-29 15:42:15.667 INFO InfoStore Agent m_cmsNames.size() = 1.
2010-12-29 15:42:15.668 INFO InfoStore Agent Pinging db9.interactivesys.com:6400.
2010-12-29 15:42:15.668 DEBUG InfoStore Agent Trying to ping using db9.interactivesys.com/10.24.34.9 at port 6400
2010-12-29 15:42:15.672 DEBUG InfoStore Agent java.net.ConnectException: Connection refused java.net.PlainSocketImpl.socketConnect(Native Method) -
Managed server is not starting with MSI mode
Managed server not starting with MSI mode even though we enabled the managed server independence mode
Started the admin server and managed server first time enabled the MSI mode.
Restarted all admin and Managed server.
We have tested the following scenarios
scenarios1: Stopped the Admin server and restarted the Managed server with MSI mode it comes up.
scenarios2:Admin server is running but not able to connect to the managed server
In this scenario
we have removed the Network cable and restarted the managed server its throwing ldap error.
<Aug 14, 2010 1:58:32 PM SGT> <Error> <Security> <BEA-090870> <The realm "myrealm" failed to be loaded: weblogic.security.service.SecurityServiceException: com.bea.common.engine.ServiceInitializationException: weblogic.security.spi.ProviderInitializationException: [Security:090730]Failed to verify credential mapper LDAP hierarchy
netscape.ldap.LDAPException: failed to connect to server ldap://sgppsr00383:16827 (91)
at netscape.ldap.LDAPConnSetupMgr.connectServer(LDAPConnSetupMgr.java:515)
at netscape.ldap.LDAPConnSetupMgr.openSerial(LDAPConnSetupMgr.java:435) at netscape.ldap.LDAPConnSetupMgr.connect(LDAPConnSetupMgr.java:274)
at netscape.ldap.LDAPConnSetupMgr.openConnection(LDAPConnSetupMgr.java:199)
at netscape.ldap.LDAPConnThread.connect(LDAPConnThread.java:109)
at netscape.ldap.LDAPConnection.connect(LDAPConnection.java:1083) at netscape.ldap.LDAPConnection.connect(LDAPConnection.java:954)
at netscape.ldap.LDAPConnection.connect(LDAPConnection.java:781)
at weblogic.ldap.EmbeddedLDAPConnection.getAndInitDelegate(EmbeddedLDAPConnection.java:2031)
at weblogic.ldap.EmbeddedLDAPConnection.add(EmbeddedLDAPConnection.java:1065) at weblogic.security.providers.credentials.DefaultCredentialMapperLDAPHelper.addEntry(DefaultCredentialMapperLDAPHelper.java:537)
at weblogic.security.providers.credentials.DefaultCredentialMapperLDAPHelper.createOrgUnit(DefaultCredentialMapperLDAPHelper.java:432)
at weblogic.security.providers.credentials.DefaultCredentialMapperLDAPHelper.verifyHierarchy(DefaultCredentialMapperLDAPHelper.java:407)
at weblogic.security.providers.credentials.DefaultCredentialMapperLDAPHelper.<init>(DefaultCredentialMapperLDAPHelper.java:146) at weblogic.security.providers.credentials.DefaultCredentialMapperLDAPHelper.getInstance(DefaultCredentialMapperLDAPHelper.java:112)
at weblogic.security.providers.credentials.DefaultCredentialMapperProviderImpl.initialize(DefaultCredentialMapperProviderImpl.java:93)
at com.bea.common.security.internal.legacy.service.SecurityProviderImpl.init(SecurityProviderImpl.java:53)
at com.bea.common.engine.internal.ServiceEngineImpl.findOrStartService(ServiceEngineImpl.java:340) at com.bea.common.engine.internal.ServiceEngineImpl.findOrStartService(ServiceEngineImpl.java:292)
at com.bea.common.engine.internal.ServiceEngineImpl.lookupService(ServiceEngineImpl.java:263)
at com.bea.common.engine.internal.ServicesImpl.getService(ServicesImpl.java:71)
at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.initializeRealm(CommonSecurityServiceManagerDelegateImpl.java:461) at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.loadRealm(CommonSecurityServiceManagerDelegateImpl.java:822)
at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.initializeRealms(CommonSecurityServiceManagerDelegateImpl.java:851)
at weblogic.security.service.CommonSecurityServiceManagerDelegateImpl.initialize(CommonSecurityServiceManagerDelegateImpl.java:1007)
at weblogic.security.service.SecurityServiceManager.initialize(SecurityServiceManager.java:854) at weblogic.security.SecurityService.start(SecurityService.java:141)
at weblogic.t3.srvr.SubsystemRequest.run(SubsystemRequest.java:64) at weblogic.work.ExecuteThread.execute(ExecuteThread.java:209) at weblogic.work.ExecuteThread.run(ExecuteThread.java:181)
- with nested exception:
Managed server looking for ldap configuration from admin server.
I have checked the all configuration file same on both managed server and admin server.
Please let me know How to recover the managed server in this scenario.
Edited by: user10773210 on Aug 16, 2010 11:55 PM
Edited by: user10773210 on Aug 17, 2010 2:38 AMthanks for the reply....
the managed server is pointing to jrokit_160_22_D1.1.1-3 jdk....the server has enough ram also...while running the managed server showing status 'STARTING' for long period of time...and the admin server health goes 'Warning' because of threadpool....when we stop the managed server then adminserver health becomes ok... -
Sun Java System Web Proxy Server (4.0.2) - manage server will not start
In short here's the scenario and main problem.
a. Proxy admin server start - no problem
b. Create a new manage server (no proxying - just testing it) using different port. It just won't start. No logs produced either.
Here's the server.xml for the new manage server.
<?xml version="1.0" encoding="UTF-8"?>
<!--
Copyright (c) 2003 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
-->
<!DOCTYPE SERVER PUBLIC "-//Sun Microsystems Inc.//DTD Sun Java System Web Proxy Server 4.0//EN" "file:///E:/Sun/ProxyServer40/bin/proxy/dtds/sun-web-proxy-server_4_0.dtd">
<SERVER>
<PROPERTY name="accesslog" value="E:/Sun/ProxyServer40/proxy-server3/logs/access"/>
<LS id="ls1" port="8083" servername="cbaob-b3-csddb1.adp1.cibc.pte"/>
<MIME id="mime1" file="mime.types"/>
<ACLFILE id="acl1" file="E:/Sun/ProxyServer40/httpacl/generated.proxy-server3.acl"/>
<USERDB id="default"/>
<FILECACHE enabled="true" maxage="30" mediumfilesizelimit="537600" mediumfilespace="10485760" smallfilesizelimit="2048" smallfilespace="1048576" transmitfile="false" maxfiles="1024" hashinitsize="0"/>
<CACHE enabled="true" cachecapacity="2000" cachedir="E:/Sun/ProxyServer40/proxy-server3/cache">
<PARTITION partitionname="part1" partitiondir="E:/Sun/ProxyServer40/proxy-server3/cache" maxsize="100" minspace="5" enabled="true"/>
<GC enabled="true" gchimargin="80" gclomargin="70" gcleavefsfull="60" gcextramargin="30"/>
</CACHE>
<LOG file="E:/Sun/ProxyServer40/proxy-server3/logs/errors" loglevel="finest"/>
</SERVER>
Nothing seems to be wrong with this. The XML format follows the specified DTD.
Would appreciate any help.
Thanks.Thanks for your reply. Yes. This is really odd.
Anyway to make the whole story short, i uninstall this proxy server 4.0.2 on this server (say server1) and try to reinstall a new proxy 4.0.13 but having odd problem (i have administration rights)
Here it goes.
a. CMD java -version is 1.4.2_XX
b. Double click the proxy 4.0.13 setup.exe - nothing happen.
c. CMD setup --javahome c:\jdk1.6_XX - nothing happen
Here retrying.
a. Login to server2 and map conection to server1
b. Double click the proxy 4.0.13 setup.exe on server1 (while on server2) - setup.exe runs. This proves the proxy setup.exe on server1 is good.
c. Make a copy of proxy 4.0.13 on server2
d. Login to server1 and map connection to server2
e. Double click the proxy 4.0.13 setup.exe on server2 (while on server1) - setup.exe did not run.
Both servers are on the same domain and i'm using same ID to access both servers
Again, no logs on the windows events (security, application, system)
This is becoming mind a boggling mystery.
Any idea what's going on?
Thanks. -
Managed server does not start with BEA-090870 security error
I am getting this autorization error
<Sep 22, 2014 11:07:23 PM EDT> <Error> <Security> <BEA-090870> <The realm "myrealm" failed to be loaded: weblogic.security.service.SecurityServiceException: com.bea.common.engine.ServiceInitializationException: weblogic.security.spi.ProviderInitializationException: A failure occurred attempting to load LDIF for provider Authorizer from file /opt/app/oracle/middleware/v12c/oracle_home/wlserver/server/lib/XACMLAuthorizerInit.ldift..
weblogic.security.service.SecurityServiceException: com.bea.common.engine.ServiceInitializationException: weblogic.security.spi.ProviderInitializationException: A failure occurred attempting to load LDIF for provider Authorizer from file /opt/app/oracle/middleware/v12c/oracle_home/wlserver/server/lib/XACMLAuthorizerInit.ldift.
It use to be working. I am looking for a way to correct this.
Thankshi
the following link may hekpful to you
http://webservices.bea.com:8080/Clarify/getCaseDetails.do?caseID=537204
open a support case with bea
Regards
Prasanna Yalam -
SBS Manager Service will not start
I seem to have a bit of a problem the SBS manager service will not start at all. I have tried rebuilding the SBS Monitoring database and this did not help. This started happening a few months after a SBS 2008 to SBS 2011 migration, does anyone have any ideas
as I no longer get reporting or alerts.
At first I thought it might have had something to do with permissions but not too sure how to check and what to check apart from the common things, DB permissions, permissions on folders etc but I may have missed something?Hi,
Regarding the current issue, since you have tried to rebuild the SBS monitoring database without any help, I suggest we could try to refer to the following article this time to see if it works.
FAQ: SBS 2011. The Windows SBS Manager service terminated unexpectedly
http://msmvps.com/blogs/bradley/archive/2013/09/19/the-windows-sbs-manager-service-terminated-unexpectedly.aspx
Best Regards,
Andy Qi
TechNet Subscriber Support
If you are
TechNet Subscription user and have any feedback on our support quality, please send your feedback
here.
Andy Qi
TechNet Community Support -
Message server will not start on AIX 6
I have a standard ECC6 system running the 185 kernel and ORACLE 10.2.0.2 on AIX 6. which is giving me a problem. I also have 2 other systems apparently with the same configuration which operate perfectly.
The problem I have is that if I stop the system the message server will not start. If I wait until the following day the message server starts pefectly. I have not been able to test stopping the system and waiting an hour or so and then restarting in the same day, so I do not know if the overnight wait is relevant.
dev_ms contains the following:
[Thr 01] Fri Jun 19 23:58:54 2009
[Thr 01] WLM Tag 'HQS/MSG' successfully set for this process
[Thr 01] MsSSetTrcLog: trc logging active, max size = 20971520 bytes
systemid 324 (IBM RS/6000 with AIX)
relno 7000
patchlevel 0
patchno 163
intno 20050900
make: multithreaded, ASCII, 64 bit, optimized
pid 254088
[Thr 01] ***LOG Q01=> MsSInit, MSStart (Msg Server 1 254088) [msxxserv_mt. 1835]
[Thr 01] SigISetDefaultAction : default handling for signal 20
[Thr 01] ***LOG Q0I=> NiIBindSocket: bind (67: Address already in use) [nixxi.cp
p 3227]
[Thr 01] *** ERROR => NiIBindSocket: SiBind failed for hdl 1 / sock 8
(SI_EPORT_INUSE/67; I4; ST; 0.0.0.0:3950) [nixxi.cpp 3227]
[Thr 01] *** ERROR => MsSCommInit: NiBufListen(3950) (rc=NIESERV_USED) [msxxserv
_mt. 10186]
[Thr 01] *** ERROR => MsSInit: MsSCommInit (internal) [msxxserv_mt. 1886]
[Thr 01] *** ERROR => main: MsSInit [msxxserv_mt. 5951]
[Thr 01] ***LOG Q02=> MsSHalt, MSStop (Msg Server 254088) [msxxserv_mt. 5999]
Regards,
Paul Richardson
Certified Netweaver, Portal and Migration Consultant
Sandpiper I.T. LtdHi,
Thr 01 ***LOG Q0I=> NiIBindSocket: bind (67: Address already in use) [nixxi.cp p 3227]
Looks like port 3227 is already used. You can check the ports by netstat -a -n from your command prompts. Also check your settings in /etc/services and /etc/hosts files.
Check your filewall rules/disable antivirus if any and give a go.
Hope this helps.
Manoj -
Managed server is not starting....
hi friends,
we have four node weblogic 10.3.5 clustered deployment of oim 11.1.1.5 ....previously everything was working fine....two of the oim managed server is not starting and throwing following error.... two are working fine and all other 4 soa servers also running fine...
####<May 20, 2012 3:43:18 PM AST> <Warning> <RMI> <server2> <WLS_OIM2> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1337517798416> <BEA-080004> <An error was thrown by rmi server: weblogic.server.RemoteLifeCycleOperationsImpl.forceShutdown()
java.lang.ExceptionInInitializerError.
java.lang.ExceptionInInitializerError
at weblogic.wsee.runtime.JMSStoreRoutableIDMapper.shutdown(JMSStoreRoutableIDMapper.java:478)
at weblogic.wsee.runtime.WebServicesRuntime.shutdown(WebServicesRuntime.java:146)
at weblogic.wsee.runtime.WseeService.haltService(WseeService.java:60)
at weblogic.server.ServiceActivator.halt(ServiceActivator.java:113)
at weblogic.t3.srvr.ServerServicesManager.haltInternal(ServerServicesManager.java:504)
at weblogic.t3.srvr.ServerServicesManager.halt(ServerServicesManager.java:336)
at weblogic.t3.srvr.T3Srvr.shutdown(T3Srvr.java:1120)
at weblogic.t3.srvr.T3Srvr.forceShutdown(T3Srvr.java:1024)
at weblogic.t3.srvr.ServerRuntime.forceShutdown(ServerRuntime.java:351)
at weblogic.server.RemoteLifeCycleOperationsImpl.forceShutdown(RemoteLifeCycleOperationsImpl.java:57)
at weblogic.server.RemoteLifeCycleOperationsImpl_WLSkel.invoke(Unknown Source)
at weblogic.rmi.internal.BasicServerRef.invoke(BasicServerRef.java:667)
at weblogic.rmi.internal.BasicServerRef$1.run(BasicServerRef.java:522)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:363)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:146)
at weblogic.rmi.internal.BasicServerRef.handleRequest(BasicServerRef.java:518)
at weblogic.rmi.internal.wls.WLSExecuteRequest.run(WLSExecuteRequest.java:118)
at weblogic.work.ExecuteThread.execute(ExecuteThread.java:209)
at weblogic.work.ExecuteThread.run(ExecuteThread.java:178)
Caused By: java.lang.IllegalStateException: Shutdown in progress
at java.lang.ApplicationShutdownHooks.add(ApplicationShutdownHooks.java:39)
at java.lang.Runtime.addShutdownHook(Runtime.java:193)
at weblogic.wsee.persistence.LogicalStore.<clinit>(LogicalStore.java:192)
at weblogic.wsee.runtime.JMSStoreRoutableIDMapper.shutdown(JMSStoreRoutableIDMapper.java:478)
at weblogic.wsee.runtime.WebServicesRuntime.shutdown(WebServicesRuntime.java:146)
at weblogic.wsee.runtime.WseeService.haltService(WseeService.java:61)
at weblogic.server.ServiceActivator.halt(ServiceActivator.java:114)
at weblogic.t3.srvr.ServerServicesManager.haltInternal(ServerServicesManager.java:504)
at weblogic.t3.srvr.ServerServicesManager.halt(ServerServicesManager.java:336)
at weblogic.t3.srvr.T3Srvr.shutdown(T3Srvr.java:1120)
at weblogic.t3.srvr.T3Srvr.forceShutdown(T3Srvr.java:1025)
at weblogic.t3.srvr.ServerRuntime.forceShutdown(ServerRuntime.java:351)
at weblogic.server.RemoteLifeCycleOperationsImpl.forceShutdown(RemoteLifeCycleOperationsImpl.java:59)
at weblogic.server.RemoteLifeCycleOperationsImpl_WLSkel.invoke(Unknown Source)
at weblogic.rmi.internal.BasicServerRef.invoke(BasicServerRef.java:668)
at weblogic.rmi.internal.BasicServerRef$1.run(BasicServerRef.java:523)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:363)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:146)
at weblogic.rmi.internal.BasicServerRef.handleRequest(BasicServerRef.java:518)
at weblogic.rmi.internal.wls.WLSExecuteRequest.run(WLSExecuteRequest.java:119)
at weblogic.work.ExecuteThread.execute(ExecuteThread.java:209)
at weblogic.work.ExecuteThread.run(ExecuteThread.java:178)
Regards
jdevthanks for the reply....
the managed server is pointing to jrokit_160_22_D1.1.1-3 jdk....the server has enough ram also...while running the managed server showing status 'STARTING' for long period of time...and the admin server health goes 'Warning' because of threadpool....when we stop the managed server then adminserver health becomes ok... -
I am trying to run a hardware test. The Computer will not start with the "D" key held?
If you are using a Blutooth keyboard, don't hold the "D" key until the keyboard is recognised (green light)
Running AHT in Lion
http://support.apple.com/kb/PH4510 -
PC will not start with the battery and charger. There's no light, no noise on fan, hard drive and CD writer. The hard drive, fan and charger are new. But I was havingproblems and sudden blackouts System 32. Try several times to install theoperating system but the pc turned off suddenly and restarted until I stop working completely. Now it does nothing and no light. I hope it can help me I need torespect and love very much this notebook.
Thanks in advance
Jose Echevarria
[email protected]Turn off your laptop, unplug all wires, remove the battery, and hold the power button for thirty seconds. Afterwards, reattach the battery and connections. If it still won't start, remove the battery and start with just the AC power. Next try without the AC power and just the battery.
- Peter -
We are in the final stage of the installation.
We are following the steps mentioned in http://www.rittmanmead.com/2013/04/upgrading-obiee-to-11-1-1-7/ .
while running the 'Configuration Assistant' to update the BI domain the Managed server is not getting started.
We are getting issue with SSL hand shake...Can any one help us to resolve this.
===========================
Configuration Assistant Log
===========================
BI Configuration
Log
Config Action BI Configuration started
Executing: opmnctl stopall
Log
Step Executing: opmnctl stopall started
Step Executing: opmnctl stopall ended successfully
Stopping Managed Server: bi_server1
Log
Step Stopping Managed Server: bi_server1 started
Step Stopping Managed Server: bi_server1 ended successfully
Upgrading JRF Shared Libraries
Log
Step Upgrading JRF Shared Libraries started
Step Upgrading JRF Shared Libraries ended successfully
Upgrading OPSS Code Grants
Log
Step Upgrading OPSS Code Grants started
Step Upgrading OPSS Code Grants ended successfully
Upgrading Oracle Business Intelligence Code Grants
Log
Step Upgrading Oracle Business Intelligence Code Grants started
Step Upgrading Oracle Business Intelligence Code Grants ended successfully
Upgrading Non-J2EE Management EAR
Log
Step Upgrading Non-J2EE Management EAR started
Step Upgrading Non-J2EE Management EAR ended successfully
Deploying BI Content Server JEE application
Log
Step Deploying BI Content Server JEE application started
Step Deploying BI Content Server JEE application ended successfully
Deploying BI Composer JEE application
Log
Step Deploying BI Composer JEE application started
Step Deploying BI Composer JEE application ended successfully
Deploying JBIPS JEE application
Log
Step Deploying JBIPS JEE application started
Step Deploying JBIPS JEE application ended successfully
Restarting AdminServer
Log
Step Restarting AdminServer started
Step Restarting AdminServer ended successfully
Starting Managed Server: bi_server1
Error
Failed to achieve state RUNNING in 3600seconds. The server is currently in state SHUTDOWN
Step Starting Managed Server: bi_server1 failed
Configuration Action 'Starting Managed Server: bi_server1' has failed. Please check logs for details.
Step Starting Managed Server: bi_server1 failed
Log
Step Starting Managed Server: bi_server1 started
Step Starting Managed Server: bi_server1 failed
Configuration Action 'Starting Managed Server: bi_server1' has failed. Please check logs for details.
Step Starting Managed Server: bi_server1 failed
Executing: opmnctl startall
Log
Upgrading Oracle Business Intelligence Catalogs
Log
===========================
Dec 13, 2013 9:36:59 AM weblogic.nodemanager.server.Handler run
WARNING: Uncaught exception in server handlerjavax.net.ssl.SSLKeyException: [Sec
urity:090482]BAD_CERTIFICATE alert was received from botd-rptobapp2.devop.vertaf
ore.com - 192.12.12.13. Check the peer to determine why it rejected the certif
icate chain (trusted CA configuration, hostname verification). SSL debug tracing
may be required to determine the exact reason the certificate was rejected.
javax.net.ssl.SSLKeyException: [Security:090482]BAD_CERTIFICATE alert was receiv
ed from botd.devop.com - 192.12.12.13. Check the peer to d
etermine why it rejected the certificate chain (trusted CA configuration, hostna
me verification). SSL debug tracing may be required to determine the exact reaso
n the certificate was rejected.
Nodemanger.log
<Oct 7, 2013 10:28:35 AM> <INFO> <Loading domains file: c:\oracle\wlserver_10.3\common\nodemanager\nodemanager.domains>
<Oct 7, 2013 10:28:38 AM> <INFO> <Loading identity key store: FileName=c:/oracle/WLSERV~1.3/server\lib\DemoIdentity.jks, Type=jks, PassPhraseUsed=true>
<Oct 7, 2013 10:28:38 AM> <INFO> <Loaded node manager configuration properties from 'c:\oracle\WLSERV~1.3\common\nodemanager\nodemanager.properties'>
<Oct 7, 2013 10:28:38 AM> <INFO> <bifoundation_domain> <bi_server1> <Startup configuration properties loaded from "C:\oracle\user_projects\domains\bifoundation_domain\servers\bi_server1\data\nodemanager\startup.properties">
<Oct 7, 2013 10:28:42 AM> <INFO> <Secure socket listener started on port 9556>
<Oct 7, 2013 10:35:51 AM> <WARNING> <Uncaught exception in server handlerjavax.net.ssl.SSLKeyException: [Security:090482]BAD_CERTIFICATE alert was received from botd.devop.com - 192.12.12.13. Check the peer to determine why it rejected the certificate chain (trusted CA configuration, hostname verification). SSL debug tracing may be required to determine the exact reason the certificate was rejected.>
javax.net.ssl.SSLKeyException: [Security:090482]BAD_CERTIFICATE alert was received from botd.devop.com - 192.12.12.13. Check the peer to determine why it rejected the certificate chain (trusted CA configuration, hostname verification). SSL debug tracing may be required to determine the exact reason the certificate was rejected.
at com.certicom.tls.interfaceimpl.TLSConnectionImpl.fireException(Unknown Source)
at com.certicom.tls.interfaceimpl.TLSConnectionImpl.fireAlertReceived(Unknown Source)
at com.certicom.tls.record.alert.AlertHandler.handle(Unknown Source)
at com.certicom.tls.record.alert.AlertHandler.handleAlertMessages(Unknown Source)
at com.certicom.tls.record.MessageInterpreter.interpretContent(Unknown Source)
at com.certicom.tls.record.MessageInterpreter.decryptMessage(Unknown Source)
at com.certicom.tls.record.ReadHandler.processRecord(Unknown Source)
at com.certicom.tls.record.ReadHandler.readRecord(Unknown Source)
at com.certicom.tls.record.ReadHandler.readUntilHandshakeComplete(Unknown Source)
at com.certicom.tls.interfaceimpl.TLSConnectionImpl.completeHandshake(Unknown Source)
at com.certicom.tls.record.ReadHandler.read(Unknown Source)
at com.certicom.io.InputSSLIOStreamWrapper.read(Unknown Source)
at sun.nio.cs.StreamDecoder.readBytes(StreamDecoder.java:264)
at sun.nio.cs.StreamDecoder.implRead(StreamDecoder.java:306)
at sun.nio.cs.StreamDecoder.read(StreamDecoder.java:158)
at java.io.InputStreamReader.read(InputStreamReader.java:167)
at java.io.BufferedReader.fill(BufferedReader.java:136)
at java.io.BufferedReader.readLine(BufferedReader.java:299)
at java.io.BufferedReader.readLine(BufferedReader.java:362)
at weblogic.nodemanager.server.Handler.run(Handler.java:71)
at java.lang.Thread.run(Thread.java:662)
Admin server Log
for protocols iiop, t3, ldap, snmp, http.>
<Dec 15, 2013 4:59:29 AM PST> <Notice> <Server> <BEA-002613> <Channel "DefaultSecure" is now listening on 192.12.12.13
:7002 for protocols iiops, t3s, ldaps, https.>
<Dec 15, 2013 4:59:29 AM PST> <Notice> <WebLogicServer> <BEA-000329> <Started WebLogic Admin Server "AdminServer" for do
main "bifoundation_domain" running in Production Mode>
<Dec 15, 2013 4:59:29 AM PST> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to RUNNING>
<Dec 15, 2013 4:59:29 AM PST> <Notice> <WebLogicServer> <BEA-000360> <Server started in RUNNING mode>
<Dec 15, 2013 5:00:12 AM PST> <Notice> <LoggingService> <BEA-320400> <The log file C:\oracle\user_projects\domains\bifou
ndation_domain\servers\AdminServer\logs\AdminServer.log will be rotated. Reopen the log file if tailing has stopped. Thi
s can happen on some platforms like Windows.>
<Dec 15, 2013 5:00:12 AM PST> <Notice> <LoggingService> <BEA-320401> <The log file has been rotated to C:\oracle\user_pr
ojects\domains\bifoundation_domain\servers\AdminServer\logs\AdminServer.log00002. Log messages will continue to be logge
d in C:\oracle\user_projects\domains\bifoundation_domain\servers\AdminServer\logs\AdminServer.log.>
CertPathTrustManagerUtils.certificateCallback: certPathValStype = 0
CertPathTrustManagerUtils.certificateCallback: validateErr = 16
CertPathTrustManagerUtils.certificateCallback: chain[0] = Serial number: -157025747728280783581574168894965558517
Issuer:C=US, ST=MyState, L=MyTown, O=MyOrganization, OU=FOR TESTING ONLY, CN=CertGenCAB
Subject:C=US, ST=MyState, L=MyTown, O=MyOrganization, OU=FOR TESTING ONLY, CN=BOTD-RPTOBAPP2
Not Valid Before:Sun Aug 12 11:27:29 PDT 2012
Not Valid After:Fri Aug 13 11:27:29 PDT 2027
Signature Algorithm:MD5withRSA
==============
Narendar ReddyHi Folks,
Any inputs in the above issue is highly appreciated.
"Error
Failed to achieve state RUNNING in 3600seconds. The server is currently in state SHUTDOWN
Step Starting Managed Server: bi_server1 failed
Configuration Action 'Starting Managed Server: bi_server1' has failed."
Regards,
Aj -
Mac OS 10.4.4 Application Server Will Not Start
Installed Mac 10.4.4 last night. The Applicaton Server worked for all my projects. Now I cannot start the Application Server in Creator or Creator 2 ea2.
Another possible problem is that I was running both Creator and Creator 2 ea2 at the same time, but neither will launch the App Server now with the other not running.
Has anyone successfully launched the App Server in Mac OS 10.4.4?
Any other ideas?
Thanks,
BillHello Sakthi,
Thanks for the help. I got the server running again by finding yet another instance of Creator and started up the Server successfully. Strangely enough, all the other instances of Creator then were able to start up (now one at a time). Another thing, when the server was not starting up it was using different port numbers than normal.
Error:
[#|2006-01-11T17:12:10.079-0500|INFO|sun-appserver-pe8.1_02|javax.enterprise.system.tools.admin|_ThreadID=17;|ADM1042:Status of dynamic reconfiguration event processing:[success]|#]
[#|2006-01-11T17:12:36.979-0500|WARNING|sun-appserver-pe8.1_02|javax.enterprise.resource.resourceadapter|_ThreadID=18;|RAR5038:Unexpected exception while creating resource|#]
[#|2006-01-11T17:12:36.980-0500|WARNING|sun-appserver-pe8.1_02|javax.enterprise.resource.resourceadapter|_ThreadID=18;|RAR5117 : Failed to obtain/create connection. Reason : Connection could not be allocated because: SQL-server rejected establishment of SQL-connection. Pointbase Server may not be running on localhost at port 29093.|#] -
Hi, I am having an issue with my SLD server. The java will not start completely. This is the log i get:
If you have any clue that would be great.
thanks
<!LOGHEADER[START]/>
<!HELP[Manual modification of the header may cause parsing problem!]/>
<!LOGGINGVERSION[1.5.3.7185 - 630]/>
<!NAME[./log/defaultTrace.trc]/>
<!PATTERN[defaultTrace.trc]/>
<!FORMATTER[com.sap.tc.logging.ListFormatter]/>
<!ENCODING[Cp1252]/>
<!FILESET[0, 20, 10485760]/>
<!PREVIOUSFILE[defaultTrace.19.trc]/>
<!NEXTFILE[defaultTrace.1.trc]/>
<!LOGHEADER[END]/>
#1.5#000BCDEF4B75001E0000000100000B4400046A834059524E#1243011859688#com.sap.di.sdic.srv.java.SDICServiceFrame##com.sap.di.sdic.srv.java.SDICServiceFrame#######SAPEngine_System_Thread[impl:5]_70##0#0#Error#1#/Applications/SDIC/Service#Java###Failed to initialize the SDIC service. An unanticipated error has occured; Error description - #1#com.sap.di.sdic.exception.DiException: StateStore Initialization requires the values to be specified for the properties"sdic.state.store.storeManager" and "sdic.nwdiservers.admin.user"#
#1.5#000BCDEF4B75001E0000000300000B4400046A8340596B1D#1243011859688#com.sap.engine.core.service630.container.ServiceRunner##com.sap.engine.core.service630.container.ServiceRunner#######SAPEngine_System_Thread[impl:5]_70##0#0#Error#1#/System/Server#Plain###Service tcdisdic~srv error. Nested exception is: com.sap.engine.frame.ServiceException: StateStore Initialization requires the values to be specified for the properties"sdic.state.store.storeManager" and "sdic.nwdiservers.admin.user"
at com.sap.di.sdic.srv.java.SDICServiceFrame.start(SDICServiceFrame.java:162)
at com.sap.engine.core.service630.container.ServiceRunner.startApplicationServiceFrame(ServiceRunner.java:214)
at com.sap.engine.core.service630.container.ServiceRunner.run(ServiceRunner.java:144)
at com.sap.engine.frame.core.thread.Task.run(Task.java:64)
at com.sap.engine.core.thread.impl5.SingleThread.execute(SingleThread.java:79)
at com.sap.engine.core.thread.impl5.SingleThread.run(SingleThread.java:150)
Caused by: com.sap.di.sdic.exception.DiException: StateStore Initialization requires the values to be specified for the properties"sdic.state.store.storeManager" and "sdic.nwdiservers.admin.user"
at com.sap.di.sdic.srv.java.SDICServiceFrame.start(SDICServiceFrame.java:149)
... 5 more
Caused by: java.lang.Exception: StateStore Initialization requires the values to be specified for the properties"sdic.state.store.storeManager" and "sdic.nwdiservers.admin.user"
... 6 more
#1.5#000BCDEF4B7500260000000000000B4400046A8340A5D8ED#1243011864701#com.sap.caf.um.metadata.imp.MetaDataTools##com.sap.caf.um.metadata.imp.MetaDataTools.MetaDataTools()#######SAPEngine_System_Thread[impl:5]_54##0#0#Info#1#/System/Server#Plain###sap.com caf/um/metadata/imp MAIN_APL70VAL_C 963656#
#1.5#000BCDEF4B75002F0000000100000B4400046A8340D0C614#1243011867513#com.sap.engine.services.rfcengine##com.sap.engine.services.rfcengine.RFCRuntimeInterfaceImpl.newProperties(int prcs, int conn)#######SAPEngine_System_Thread[impl:5]_35##0#0#Error#1#/System/Server#Java###enter newProperties()##
#1.5#000BCDEF4B75002F0000000300000B4400046A8340D702A6#1243011867919#com.sap.engine.services.rfcengine##com.sap.engine.services.rfcengine.RFCRuntimeInterfaceImpl.init()#######SAPEngine_System_Thread[impl:5]_35##0#0#Error#1#/System/Server#Java###SNC properties not found ##
#1.5#000BCDEF4B7500300000000000000B4400046A8340F313F1#1243011869762#com.sap.caf.um.relgroups.imp.persistence.DataSource##com.sap.caf.um.relgroups.imp.persistence.DataSource.DataSource()#######SAPEngine_System_Thread[impl:5]_4##0#0#Info#1#/System/Server#Plain###sap.com caf/um/relgroups/imp MAIN_APL70VAL_C 963842#
#1.5#000BCDEF4B7500380000000100000B4400046A83412AA249#1243011873402#com.adobe.service.sap.configuration##com.adobe.service.sap.configuration#######OrderedChannel for service##0#0#Error#1#/System/Security#Plain###Error while reading trusted anchor configuration information:
com.sap.security.core.server.securestorage.exception.ObjectRetrievalException: Could not find clientID servicescomadobeDocumentServicesConfigurationAdobeConfigurationService~jar
at com.sap.security.core.server.securestorage.remote.RemoteSecureStorageClientContextImpl.getClientsStorageLocation(RemoteSecureStorageClientContextImpl.java:231)
at com.sap.security.core.server.securestorage.remote.RemoteSecureStorageClientContextImpl.retrieveObject(RemoteSecureStorageClientContextImpl.java:724)
at com.adobe.service.sap.configuration.ConfigurationService.readXML(Unknown Source)
at com.adobe.service.sap.configuration.ConfigurationService.<init>(Unknown Source)
at com.adobe.service.sap.configuration.ServiceFrame.start(Unknown Source)
at com.sap.engine.core.service630.container.ServiceRunner.startApplicationServiceFrame(ServiceRunner.java:214)
at com.sap.engine.core.service630.container.ServiceRunner.run(ServiceRunner.java:144)
at com.sap.engine.frame.core.thread.Task.run(Task.java:64)
at com.sap.engine.core.thread.impl5.SingleThread.execute(SingleThread.java:79)
at com.sap.engine.core.thread.impl5.SingleThread.run(SingleThread.java:150)
#1.5#000BCDEF4B7500380000000300000B4400046A83412AAC7B#1243011873402#com.adobe.service.sap.configuration##com.adobe.service.sap.configuration#######OrderedChannel for service##0#0#Error#1#/System/Security#Plain###Error while reading credential configuration information:
com.sap.security.core.server.securestorage.exception.ObjectRetrievalException: Could not find clientID servicescomadobeDocumentServicesConfigurationAdobeConfigurationService~jar
at com.sap.security.core.server.securestorage.remote.RemoteSecureStorageClientContextImpl.getClientsStorageLocation(RemoteSecureStorageClientContextImpl.java:231)
at com.sap.security.core.server.securestorage.remote.RemoteSecureStorageClientContextImpl.retrieveObject(RemoteSecureStorageClientContextImpl.java:724)
at com.adobe.service.sap.configuration.ConfigurationService.readXML(Unknown Source)
at com.adobe.service.sap.configuration.ConfigurationService.<init>(Unknown Source)
at com.adobe.service.sap.configuration.ServiceFrame.start(Unknown Source)
at com.sap.engine.core.service630.container.ServiceRunner.startApplicationServiceFrame(ServiceRunner.java:214)
at com.sap.engine.core.service630.container.ServiceRunner.run(ServiceRunner.java:144)
at com.sap.engine.frame.core.thread.Task.run(Task.java:64)
at com.sap.engine.core.thread.impl5.SingleThread.execute(SingleThread.java:79)
at com.sap.engine.core.thread.impl5.SingleThread.run(SingleThread.java:150)
#1.5#000BCDEF4B7500380000000500000B4400046A83412AB51D#1243011873402#com.adobe.service.sap.configuration##com.adobe.service.sap.configuration#######OrderedChannel for service##0#0#Error#1#/System/Security#Plain###Error while reading CRL configuration information:
com.sap.security.core.server.securestorage.exception.ObjectRetrievalException: Could not find clientID servicescomadobeDocumentServicesConfigurationAdobeConfigurationService~jar
at com.sap.security.core.server.securestorage.remote.RemoteSecureStorageClientContextImpl.getClientsStorageLocation(RemoteSecureStorageClientContextImpl.java:231)
at com.sap.security.core.server.securestorage.remote.RemoteSecureStorageClientContextImpl.retrieveObject(RemoteSecureStorageClientContextImpl.java:724)
at com.adobe.service.sap.configuration.ConfigurationService.readXML(Unknown Source)
at com.adobe.service.sap.configuration.ConfigurationService.<init>(Unknown Source)
at com.adobe.service.sap.configuration.ServiceFrame.start(Unknown Source)
at com.sap.engine.core.service630.container.ServiceRunner.startApplicationServiceFrame(ServiceRunner.java:214)
at com.sap.engine.core.service630.container.ServiceRunner.run(ServiceRunner.java:144)
at com.sap.engine.frame.core.thread.Task.run(Task.java:64)
at com.sap.engine.core.thread.impl5.SingleThread.execute(SingleThread.java:79)
at com.sap.engine.core.thread.impl5.SingleThread.run(SingleThread.java:150)
#1.5#000BCDEF4B7500380000000700000B4400046A83412ABDBE#1243011873402#com.adobe.service.sap.configuration##com.adobe.service.sap.configuration#######OrderedChannel for service##0#0#Error#1#/System/Security#Plain###Error while reading password configuration information:
com.sap.security.core.server.securestorage.exception.ObjectRetrievalException: Could not find clientID servicescomadobeDocumentServicesConfigurationAdobeConfigurationService~jar
at com.sap.security.core.server.securestorage.remote.RemoteSecureStorageClientContextImpl.getClientsStorageLocation(RemoteSecureStorageClientContextImpl.java:231)
at com.sap.security.core.server.securestorage.remote.RemoteSecureStorageClientContextImpl.retrieveObject(RemoteSecureStorageClientContextImpl.java:724)
at com.adobe.service.sap.configuration.ConfigurationService.readXML(Unknown Source)
at com.adobe.service.sap.configuration.ConfigurationService.<init>(Unknown Source)
at com.adobe.service.sap.configuration.ServiceFrame.start(Unknown Source)
at com.sap.engine.core.service630.container.ServiceRunner.startApplicationServiceFrame(ServiceRunner.java:214)
at com.sap.engine.core.service630.container.ServiceRunner.run(ServiceRunner.java:144)
at com.sap.engine.frame.core.thread.Task.run(Task.java:64)
at com.sap.engine.core.thread.impl5.SingleThread.execute(SingleThread.java:79)
at com.sap.engine.core.thread.impl5.SingleThread.run(SingleThread.java:150)
Jean SeguinHi,
The user SAPJSF is not lock and here is the output of the Stdserver.out
stdout/stderr redirect
node name : server0
pid : 5800
system name : IS1
system nr. : 01
started at : Fri May 22 14:50:38 2009
Reserved 1610612736 (0x60000000) bytes before loading DLLs.
[Thr 5756] Fri May 22 14:50:39 2009
[Thr 5756] MtxInit: -2 0 0
CompilerOracle: exclude com/sapportals/portal/pb/layout/taglib/ContainerTag addIviewResources
CompilerOracle: exclude com/sap/engine/services/keystore/impl/security/CodeBasedSecurityConnector getApplicationDomain
CompilerOracle: exclude com/sap/engine/services/rmi_p4/P4StubSkeletonGenerator generateStub
CompilerOracle: exclude com/sapportals/portal/prt/util/StringUtils escapeToJS
CompilerOracle: exclude com/sapportals/portal/prt/core/broker/PortalServiceItem startServices
CompilerOracle: exclude com/sap/engine/services/webservices/server/deploy/WSConfigurationHandler downloadFile
CompilerOracle: exclude com/sapportals/portal/prt/jndisupport/util/AbstractHierarchicalContext lookup
CompilerOracle: exclude com/sapportals/portal/navigation/cache/CacheNavigationNode getAttributeValue
CompilerOracle: exclude com/sapportals/portal/navigation/TopLevelNavigationiView PrintNode
CompilerOracle: exclude com/sapportals/wcm/service/ice/wcm/ICEPropertiesCoder encode
CompilerOracle: exclude com/sap/lcr/pers/delta/importing/ObjectLoader loadObjects
CompilerOracle: exclude com/sap/engine/services/webservices/jaxrpc/encoding/InstanceBuilder readElement
CompilerOracle: exclude com/sap/engine/services/webservices/jaxrpc/encoding/InstanceBuilder readSequence
CompilerOracle: exclude com/sap/engine/services/webservices/jaxrpc/encoding/TypeMappingImpl initializeRelations
CompilerOracle: exclude com/sap/engine/services/webservices/jaxrpc/encoding/GeneratedComplexType _loadInto
SAP J2EE Engine Version 7.00 PatchLevel is starting...
Loading: LogManager ... 6420 ms.
Loading: PoolManager ... 0 ms.
Loading: ApplicationThreadManager ... 440 ms.
Loading: ThreadManager ... 76 ms.
Loading: IpVerificationManager ... 46 ms.
Loading: ClassLoaderManager ... 30 ms.
Loading: ClusterManager ... 638 ms.
Loading: LockingManager ... 227 ms.
Loading: ConfigurationManager ... 8136 ms.
Loading: LicensingManager ... 76 ms.
Loading: CacheManager ... 410 ms.
Loading: ServiceManager ...
Loading services.:
Service memory started. (45 ms).
Service cross started. (243 ms).
Service file started. (289 ms).
Service runtimeinfo started. (30 ms).
Service timeout started. (106 ms).
Service trex.service started. (106 ms).
Service p4 started. (744 ms).
Service classpath_resolver started. (30 ms).
Service userstore started. (243 ms).
Service jmx_notification started. (532 ms).
Service log_configurator started. (24331 ms).
Service locking started. (15 ms).
Service http started. (759 ms).
Service naming started. (1775 ms).
Service appclient started. (228 ms).
Service failover started. (213 ms).
Service jmsconnector started. (304 ms).
Service javamail started. (410 ms).
Service ts started. (349 ms).
Service licensing started. (30 ms).
Service connector started. (380 ms).
Service iiop started. (652 ms).
Service webservices started. (1700 ms).
Service deploy started. (31390 ms).
Service configuration started. (61 ms).
Service MigrationService started. (106 ms).
Service bimmrdeployer started. (30 ms).
Service dbpool started. (6041 ms).
Service com.sap.security.core.ume.service started. (7680 ms).
Service tcdisdic~srv started. (1776 ms).
Service security started. (4068 ms).
Service classload started. (228 ms).
Service applocking started. (228 ms).
Service shell started. (379 ms).
Service ejb started. (547 ms).
Service tceCATTPingservice started. (425 ms).
Service telnet started. (501 ms).
Service dsr started. (1062 ms).
Service servlet_jsp started. (1791 ms).
Service webdynpro started. (1426 ms).
Service cafummetadata~imp started. (2095 ms).
Service keystore started. (2474 ms).
Service ssl started. (15 ms).
Service cafruntimeconnectivity~impl started. (50818 ms).
Service jmx started. (3111 ms).
Service tcsecsecurestorage~service started. (1199 ms).
Service tcsecwssec~service started. (835 ms).
Service cafumrelgroups~imp started. (4099 ms).
Service CUL started. (2550 ms).
Service tcsecdestinations~service started. (2824 ms).
Service apptracing started. (1351 ms).
Service com.adobe~DataManagerService started. (3187 ms).
Service pmi started. (1138 ms).
Service tcsecvsi~service started. (1988 ms).
Service sld started. (5525 ms).
Service basicadmin started. (4568 ms).
Service com.adobe~DocumentServicesDestProtoService started. (1548 ms).
Service com.adobe~DocumentServicesBinaries2 started. (1624 ms).
Service com.adobe~DocumentServicesLicenseSupportService started. (1336 ms).
Service adminadapter started. (364 ms).
Service com.adobe~LicenseService started. (470 ms).
Service monitor started. (1564 ms).
Service com.adobe~DocumentServicesConfiguration started. (2762 ms).
Service com.adobe~TrustManagerService started. (182 ms).
Service com.adobe~PDFManipulation started. (4888 ms).
Service tc.CBS.Service started. (10564 ms).
Service com.adobe~FontManagerService started. (10049 ms).
Service com.sap.aii.af.cpa.svc started. (9821 ms).
Service com.sap.aii.af.security.service started. (31 ms).
Service tc.monitoring.logviewer started. (19216 ms).
Service com.sap.aii.af.svc started. (2808 ms).
Service com.sap.aii.af.ms.svc started. (1366 ms).
Service com.adobe~XMLFormService started. (6315 ms).
Service com.sap.aii.adapter.bc.svc started. (106 ms).
Service com.sap.aii.adapter.marketplace.svc started. (243 ms).
Service com.sap.aii.adapter.xi.svc started. (182 ms).
Service com.sap.aii.adapter.file.svc started. (304 ms).
Service com.sap.aii.adapter.jdbc.svc started. (288 ms).
Service com.sap.aii.adapter.rfc.svc started. (122 ms).
Service jms_provider started. (22373 ms).
Service com.sap.aii.adapter.mail.svc started. (1442 ms).
Service com.sap.aii.adapter.jms.svc started. (895 ms).
Service com.sap.aii.af.ispeak.svc started. (728 ms).
Service rfcengine started. (73524 ms).
ServiceManager started for 148445 ms.
Framework started for 166083 ms.
SAP J2EE Engine Version 7.00 PatchLevel is running!
PatchLevel October 23, 2006 07:41 GMT -
WebLogic 9.2 Managed Server Is not starting
I have WebLogic 9.2 Application Server installed on Solaris Box and have deployed some ear and war files.
If I try to start the managed server its getting the following exception leading to FORCE_SHUTDOWN of the server.
Please help me if any one know the solution for this.
The Exception is
<Jan 5, 2009 4:46:12 AM CST> <Info> <WebLogicServer> <BEA-000377> <Starting WebLogic Server with Java HotSpot(TM) Server VM Ve
rsion 1.5.0_10-b03 from Sun Microsystems Inc.>
java.io.IOException: Error while downloading files from admin server. Undelying error is : null
at weblogic.deploy.service.datatransferhandlers.HttpDataTransferHandler.getDataAsStream(HttpDataTransferHandler.java:7
1)
at weblogic.deploy.service.datatransferhandlers.DataHandlerManager$RemoteDataTransferHandler.getDataAsStream(DataHandl
erManager.java:153)
at weblogic.deploy.internal.targetserver.datamanagement.ConfigDataUpdate.doDownload(ConfigDataUpdate.java:75)
at weblogic.deploy.internal.targetserver.datamanagement.DataUpdate.download(DataUpdate.java:56)
at weblogic.deploy.internal.targetserver.datamanagement.Data.prepareDataUpdate(Data.java:98)
at weblogic.management.provider.internal.RuntimeAccessDeploymentReceiverService.downloadFiles(RuntimeAccessDeploymentR
eceiverService.java:892)
at weblogic.management.provider.internal.RuntimeAccessDeploymentReceiverService.updateFiles(RuntimeAccessDeploymentRec
eiverService.java:851)
at weblogic.management.provider.internal.RuntimeAccessDeploymentReceiverService.handleRegistrationResponse(RuntimeAcce
ssDeploymentReceiverService.java:706)
at weblogic.management.provider.internal.RuntimeAccessDeploymentReceiverService.registerHandler(RuntimeAccessDeploymen
tReceiverService.java:677)
at weblogic.management.provider.internal.RuntimeAccessDeploymentReceiverService.start(RuntimeAccessDeploymentReceiverS
ervice.java:169)
at weblogic.t3.srvr.ServerServicesManager.startService(ServerServicesManager.java:374)
at weblogic.t3.srvr.ServerServicesManager.startInStandbyState(ServerServicesManager.java:125)
at weblogic.t3.srvr.T3Srvr.initializeStandby(T3Srvr.java:630)
at weblogic.t3.srvr.T3Srvr.startup(T3Srvr.java:402)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:361)
at weblogic.Server.main(Server.java:67)
<Jan 5, 2009 4:46:19 AM CST> <Error> <Management> <BEA-141196> <The managed server could not update the configuration files du
ring the registration with the deployment service. The update failed due to an exception:
weblogic.management.DeploymentException: Exception occured while downloading files
at weblogic.deploy.internal.targetserver.datamanagement.ConfigDataUpdate.doDownload(ConfigDataUpdate.java:83)
at weblogic.deploy.internal.targetserver.datamanagement.DataUpdate.download(DataUpdate.java:56)
at weblogic.deploy.internal.targetserver.datamanagement.Data.prepareDataUpdate(Data.java:98)
at weblogic.management.provider.internal.RuntimeAccessDeploymentReceiverService.downloadFiles(RuntimeAccessDeploymentR
eceiverService.java:892)
at weblogic.management.provider.internal.RuntimeAccessDeploymentReceiverService.updateFiles(RuntimeAccessDeploymentRec
eiverService.java:851)
at weblogic.management.provider.internal.RuntimeAccessDeploymentReceiverService.handleRegistrationResponse(RuntimeAcce
ssDeploymentReceiverService.java:706)
at weblogic.management.provider.internal.RuntimeAccessDeploymentReceiverService.registerHandler(RuntimeAccessDeploymen
tReceiverService.java:677)
at weblogic.management.provider.internal.RuntimeAccessDeploymentReceiverService.start(RuntimeAccessDeploymentReceiverS
ervice.java:169)
at weblogic.t3.srvr.ServerServicesManager.startService(ServerServicesManager.java:374)
at weblogic.t3.srvr.ServerServicesManager.startInStandbyState(ServerServicesManager.java:125)
at weblogic.t3.srvr.T3Srvr.initializeStandby(T3Srvr.java:630)
at weblogic.t3.srvr.T3Srvr.startup(T3Srvr.java:402)
at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:361)
at weblogic.Server.main(Server.java:67)
java.io.IOException: Error while downloading files from admin server. Undelying error is : null
at weblogic.deploy.service.datatransferhandlers.HttpDataTransferHandler.getDataAsStream(HttpDataTransferHandler.java:7
1)
at weblogic.deploy.service.datatransferhandlers.DataHandlerManager$RemoteDataTransferHandler.getDataAsStream(DataHandl
erManager.java:153)
at weblogic.deploy.internal.targetserver.datamanagement.ConfigDataUpdate.doDownload(ConfigDataUpdate.java:75)
at weblogic.deploy.internal.targetserver.datamanagement.DataUpdate.download(DataUpdate.java:56)
at weblogic.deploy.internal.targetserver.datamanagement.Data.prepareDataUpdate(Data.java:98)
at weblogic.management.provider.internal.RuntimeAccessDeploymentReceiverService.downloadFiles(RuntimeAccessDeploymentR
eceiverService.java:892)
at weblogic.management.provider.internal.RuntimeAccessDeploymentReceiverService.updateFiles(RuntimeAccessDeploymentRec
eiverService.java:851)
at weblogic.management.provider.internal.RuntimeAccessDeploymentReceiverService.handleRegistrationResponse(RuntimeAcce
ssDeploymentReceiverService.java:706)
at weblogic.management.provider.internal.RuntimeAccessDeploymentReceiverService.registerHandler(RuntimeAccessDeploymen
tReceiverService.java:677)
at weblogic.management.provider.internal.RuntimeAccessDeploymentReceiverService.start(RuntimeAccessDeploymentReceiverS
ervice.java:169)
Thanks
Shailesh
Edited by: user6488619 on Jan 5, 2009 6:48 PMI'd say it's time to file a support case. Go to [https://support.bea.com] for this. You'll have to register if you haven't before. Note that this portal is going away at the end of this month.
Maybe you are looking for
-
Unable to get Material No and Description from VBAP
Hi Gurus Can anyone please help me to get material number and description from vbap table, The report is fine but I am unable to get material no and description. regards report ZCHGDOC_BY_SALES no standard page heading line-
-
Cannot send email SMTP to yahoo business email
i have yahoo business email, with 3 email accounts. iphone 3g will happily read the emails of the one account i want it to, but i cannot successfully reply or create new emails, send fails. i tried to create a gmail account and use its smtp server. t
-
I'm not that great at Flash, but I am designing a website for a buddy of mine who is a photographer. I downloaded a couple of templates from i-stock for the home page and the galleries. I'm pretty good with Dreamweaver and I assumed once I had edited
-
How do I make an action only apply to PDFs (in a folder)?
I am trying to attemp to create an action which I would apply on a folder. I want to resave all PDFs in the folder to open with the Navigation Panel open. Is there a way in the action step set up to specifiy that this action only happen to PDFs? O
-
Help! Premiere CS3 won't play any mp3s!!
This has always worked; I don't know what has changed. Now, if I import mp3s, all looks well until I try to play them either on the timeline or source window. There's no visual soundwave present whatsoever and it just plays silence (though for the ri