MPLS migration from IPv4 and IPv6

Hello,
i have existing MPLS VPN setup using IPv4 between all devices (P,PE,CPE), i want to start to migrate to IPv6 but i want to start the migration for one link between P and PE and all other devices will be the same (IPv4). Can you please tell me how i can acheive this scenario without impcat the services because is life.
Thanks

Dear All,
when i configured IPv6 between PE and CPE the neighbor between them is idle the following the configuration between PE and CPE:
PE:
router bgp 100
bgp router-id 10.200.200.3
no bgp default ipv4-unicast
bgp log-neighbor-changes
neighbor MPLS-Group peer-group
neighbor MPLS-Group remote-as 100
neighbor MPLS-Group update-source Loopback0
neighbor MPLS-Group-IPV6 peer-group
neighbor MPLS-Group-IPV6 remote-as 100
neighbor MPLS-Group-IPV6 update-source Loopback0
neighbor 10.200.200.5 peer-group MPLS-Group
neighbor 2002:10:200:200::5 peer-group MPLS-Group-IPV6
address-family ipv4
no synchronization
no auto-summary
exit-address-family
address-family vpnv4
neighbor MPLS-Group send-community both
neighbor MPLS-Group next-hop-self
neighbor 10.200.200.5 activate
exit-address-family
address-family vpnv6
neighbor MPLS-Group-IPV6 send-community both
neighbor MPLS-Group-IPV6 next-hop-self
neighbor 2002:10:200:200::5 activate
exit-address-family
address-family ipv4 vrf TEST
no synchronization
redistribute connected
neighbor 10.225.0.2 remote-as 101
neighbor 10.225.0.2 activate
exit-address-family
address-family ipv6 vrf TEST
redistribute connected
no synchronization
neighbor 2002:10:225::2 remote-as 101
neighbor 2002:10:225::2 activate
exit-address-family
ipv6 router ospf 200
router-id 10.200.200.3
log-adjacency-changes
mpls ldp router-id Loopback0
CPE:
interface Loopback0
ip address 10.225.100.1 255.255.255.255
ipv6 address 2002:10:225:100::1/128
interface FastEthernet0/0
no ip address
shutdown
duplex half
interface GigabitEthernet1/0
ip address 10.225.0.2 255.255.255.252
negotiation auto
ipv6 address 2002:10:225::2/126
router bgp 101
no synchronization
bgp router-id 10.225.100.1
bgp log-neighbor-changes
network 10.225.100.1 mask 255.255.255.255
neighbor 10.225.0.1 remote-as 100
neighbor 2002:10:225::1 remote-as 100
no auto-summary
address-family ipv6
no synchronization
network 2002:10:225:100::1/128
neighbor 2002:10:225::1 activate
exit-address-family
CPE-1#show ip bgp summary
BGP router identifier 10.225.100.1, local AS number 101
BGP table version is 4, main routing table version 4
2 network entries using 242 bytes of memory
2 path entries using 104 bytes of memory
3/2 BGP path/bestpath attribute entries using 228 bytes of memory
1 BGP AS-PATH entries using 24 bytes of memory
0 BGP route-map cache entries using 0 bytes of memory
0 BGP filter-list cache entries using 0 bytes of memory
BGP using 598 total bytes of memory
BGP activity 4/0 prefixes, 4/0 paths, scan interval 60 secs
Neighbor        V    AS MsgRcvd MsgSent   TblVer InQ OutQ Up/Down State/PfxRcd
10.225.0.1      4   100       6       5        4    0    0 00:01:50        1
2002:10:225::1 4   100       0       0        0    0    0 never    Idle
and i received this error:
*Nov 24 15:40:17.715: %BGP-5-ADJCHANGE: neighbor 2002:10:225::2 vpn TEST                                                                                        Up
*Nov 24 15:40:19.079: %BGP-5-ADJCHANGE: neighbor 10.225.0.2 vpn vrf TEST Up
*Nov 24 15:40:23.067: %BGP-3-NOTIFICATION: sent to neighbor 2002:10:225::2 passi                                                                                        ve 2/8 (no supported AFI/SAFI) 3 bytes 000101
Thanks

Similar Messages

Migrate UAG internal adapter from IPv4 to IPv6

I have DirectAccess running successfully for a couple of years now.
However, we now need to migrate our servers from IPv4 to IPv6 (will run side by side). The IPv6 range is a /48 range we received from our ISP
The internal interface of our DA UAG server will also get a IPv6 address. After that DA needs to be reconfigured with the new internal IPv6 interface and a client range for IP-HTTPS and NAT64/DNS64 needs to be specified.
The question is, what will happen with the laptops that are outside of the LAN and don't come inside for new domain policies? Will they reconnect with the new settings or will they loose connectivity? Do they get the new IPv6 routes for the tunnel
adapters?

I have DirectAccess running successfully for a couple of years now.
However, we now need to migrate our servers from IPv4 to IPv6 (will run side by side). The IPv6 range is a /48 range we received from our ISP
The internal interface of our DA UAG server will also get a IPv6 address. After that DA needs to be reconfigured with the new internal IPv6 interface and a client range for IP-HTTPS and NAT64/DNS64 needs to be specified.
The question is, what will happen with the laptops that are outside of the LAN and don't come inside for new domain policies? Will they reconnect with the new settings or will they loose connectivity? Do they get the new IPv6 routes for the tunnel
adapters?

Uprading deployed Cluster from Ipv4 to Ipv6

Hi Friends,
i have already running and deployed a windows cluster for my SQL 2008 and Exchange 2010 Dag in different servers with ipv4 however the company management decided that we have to upgrade all servers connection from ipv4 to ipv6.
as you know that when we create a cluster it also create a virtual connection for connecting users in my case its created with ipv4.
now how am i suppose to change that virtual connection from ipv4 to ipv6 in windows 2008 R2 clustering i mean overall how to achieve my target without destroying anything.
please advise.
thanks greenman

Hi GreeMann,
Start with Windows Server 2008 IPv6 using in the Cluster service will support this functionality as well. This includes being able to support IPv6 IP address resources
and IPv4 IP address resources either alone or in combination in a failover cluster.
Failover clustering also supports 6-4 and Intra-site Automatic Tunneling Addressing Protocol (ISATAP). Additionally, failover clustering supports only IPv6 addresses that
allow for dynamic registration in Domain Name System (DNS) (AAAA host records and the IP6.ARPA reverse look-up zone). Currently, there are three types of IPv6 address types: global, site local, and link local. Dynamic DNS registrations will not occur for link
local addresses and therefore cannot be used in a failover cluster.
But there have some
application has the limited IPv6 support or full IPv6 support, the Exchange Server 2010 has the limited IPv6 support and general speaking, IPV6 is supported for SQL server 2005,2008,2008r2 and SQL 2012, the detail supported
service you can refer the following KB:
IPv6 Support in Microsoft Products and Services
http://technet.microsoft.com/en-us/network/hh994905.aspx
More information:
IPv6 Security Considerations and Recommendations
http://technet.microsoft.com/en-us/library/bb726956.aspx
I’m glad to be of help to you!
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

WRT54G v6 not working with new Motorola SB6141 on Comcast (IPv4 and IPv6)

My WRT54G v6 not working with a new Motorola SB6141 Cable Modem on Comcast (IPv4 and IPv6).
Yesterday, I had my old DOCSIS 1.1 cable modem and the WRT54G had been working just fine for the past 8 years.
Last night, I swap in the DOCSIS 3.0 SB6141 cable modem, and now the WRT54G keeps losing the internet connection. When I go into the status page for the WRT54G, I often do not see DNS servers and sometimes do not even see an IP address.
If I connect a PC directly to the SB6141 cable modem, I have no problems whatsoever. But whenever I connect through the WRT54G and power cycle both devices, then I have internet connectivity for about an hour before it drops out. I have noticed my gateway IP address and DNS servers change at that time as well. I can also force the Linksys to lose connectivity by doing a DHCP release/renew on the Linksys status page.
Is this behavior because of the dual stack (IPv4 and IPv6) coming through the cable modem from Comcast now? Is there any way I can keep using my WRT54G v6 now that I have the SB6141 cable modem?

You just have to install it correctly.
http://kb.linksys.com/Linksys/ukp.aspx?pid=80&login=1&app=search&vw=1&articleid=3686

Dynamic DNS for ipv4 AND ipv6?

tl;dr: do you know any dynamic dns service and updater daemon that supports both ipv4 and ipv6?
Hi,
ever since my provider supplied me with a proper dual stack account (real ipv4, real ipv6) for internet access I got some kind of little problem regarding the services I host at home. So this is mainly about email. I have a server sitting behind my router that has an open submission and IMAPS port. For ipv4 I've been using the NAT and dyndns features of my router (fritzbox) without any problem. For ipv6 there is no NAT (at least as far as my router is concerned). What I can do though is to open the firewall for incoming ports dynamically based on the interface identifier. So if someone wants to connect to an ipv6 address that would map to my server the router knows to not block the traffic. For this to work though I need update a dynamic DNS record with the public ipv6 address that my server gets to use (something out of the prefix my provider assignes me). This server is an arch linux box. I tried to use inadyn-mt with some systemd unit file I found through google but this does not seem to work right. When I'm in ipv4-only networks (on a mobile connection for example) I often can't resolve the right ip address of my server through dyndns. The thing is that my server doesn't know about a changed ipv4 address because this is handled by the router. It does only know about when his own ipv6 address changes/expires. Based on when this happens inadyn-mt might fire an update to dyndns and with that also pick up the new ipv4 address, but this is not guaranteed.
Any suggenstions, tool and/or service proposals? Is there a way dns-wise to add a CNAME alias just for A records and not for AAAA?

I currently use cloudflare as the DNS servers for my domain as it's free and allows to update certain records with their API. I only use it for IPv4, but since they support AAAA records, I assume it will work for IPv6 just as well. It should be quite simple for you to update the script to get the ip of a given interface instead of fetching it from the net.
#!/bin/sh
# modified by jfro from http://www.cnysupport.com/index.php/linode-dynamic-dns-ddns-update-script
# Uses curl to be compatible with machines that don't have wget by default
# modified by Ross Hosman for use with cloudflare.
cfkey=<your api key>
cfuser=<your username>
cfhost=<hostname you want to update>
WAN_IP=`curl -s http://icanhazip.com/`
if [ -f $HOME/.wan_ip-cf.txt ]; then
OLD_WAN_IP=`cat $HOME/.wan_ip-cf.txt`
else
OLD_WAN_IP=""
fi
perl -i -pe 'chomp if eof' /var/log/cfclient.log
if [ "$WAN_IP" = "$OLD_WAN_IP" ]; then
echo -ne "." >> /var/log/cfclient.log
else
echo $WAN_IP > $HOME/.wan_ip-cf.txt
echo -ne "\nUpdating IP to $WAN_IP\n" >> /var/log/cfclient.log
curl -s https://www.cloudflare.com/api.html?a=DIUP\&hosts="$cfhost"\&u="$cfuser"\&tkn="$cfkey"\&ip="$WAN_IP" >> /var/log/cfclient.log
fi
echo -ne "\n" >> /var/log/cfclient.log

Problem running apache dual stack IPv4 and IPv6

Hello!
I am running a single Lion-Server with one public IPv4 address. Because my Provider is able to support IPv6 now, I ordered a public IPv6 address for my server. (To learn IPv6)
I setup IPv6 address and setup the firewall with ip6fw - everything works fine, I can connect to ssh and afp via IPv4 or IPv6 but when I try to connect to my wiki over IPv6 I get the certificate question (unknown certificate ... blah) click continue and the certificate is loeded againe - I end up in an infinte loop of certificate questions.
The part of the firewall config looks like this:
20515 allow tcp from any to any 443
20516 allow tcp from any to any 8443
20517 allow tcp from any to any 1640
I looked into apache config:
/etc/apache2/sites/virtual_host_global.conf has this entries:
Listen *:443
NameVirtualHost *:443
Listen *:80
NameVirtualHost *:80
I have only one domain and only one single virtual host as defined in /etc/apache2/sites/0000_any_443_.conf:
## Default Virtual Host Configuration
<VirtualHost *:443>
        ServerAdmin [email protected]
        DocumentRoot "/Library/Server/Web/Data/Sites/Default"
        DirectoryIndex index.html index.php /wiki/ default.html
        CustomLog "/var/log/apache2/access_log" combinedvhost
        ErrorLog "/var/log/apache2/error_log"
        <IfModule mod_ssl.c>
                SSLEngine On
                SSLCipherSuite "ALL:!aNULL:!ADH:!eNULL:!LOW:!EXP:RC4+RSA:+HIGH:+MEDIUM"
                SSLProxyEngine On
                SSLProtocol -ALL +SSLv3 +TLSv1
                SSLCertificateFile "/etc/certificates/www.ABCDE.de.1A00F8DFC2738F25D26E3248A4C8F687D7EA7F32.cert.p em"
                SSLCertificateKeyFile "/etc/certificates/www.ABCDE.de.1A00F8DFC2738F25D26E3248A4C8F687D7EA7F32.key.pe m"
                SSLCertificateChainFile "/etc/certificates/www.ABCDE.de.1A00F8DFC2738F25D26E3248A4C8F687D7EA7F32.chain. pem"
                SSLProxyProtocol -ALL +SSLv3 +TLSv1
        </IfModule>
        <Directory "/Library/Server/Web/Data/Sites/Default">
                Options All +MultiViews -ExecCGI -Indexes
                AllowOverride None
                <IfModule mod_dav.c>
                        DAV Off
                </IfModule>
        </Directory>
</VirtualHost>
I have not modified the apache config by hand until now - but this was an upgrade from Snow Leopard Server. At the moment I am a littel scared to upgrade to Mountain Lion server because this server runs mail and calender services for my company.
I tried to setup "Listen" entry with dedicated IP-addresses, one for IPv4 and one for IPv6 but this only leads to the same problem - IPv4 works, IPv6 ends in an infinte loop.
I found somewhere that I had to duplicate virtual hosts setup for IPv4 and IPv6 but afaik "Server.app" will overwrite it, right?
Every hint is welcome, bye
Christoph
P.S. Sorry just saw that I posted to ML-Server discussions not Lion-Server, but maybe someone can tell me that I can upgrade without scare.
Message was edited by: Christoph Ewering1

Hello!
Did some more testing and found that FireFox works with the loopback-address.
https://[::1]/
So, the address above works with FireFox after accepting the certificate - Safari loops in the dialog accepting the certificate.
Then I tried the link-local-address but it looks like apache does not listen to that address at all
Then I tried the global-address and got to:
Safari looping in the certificate dialog
FireFox brings an alert „sec_err_bad_database"
BTW this tests were made on the server that runs the apache. So no firewall between the browser and the server.
No one using Mac OS X server in a dual stack enviroment?
Bye,
eweri

Best way to pass IPv4 and IPv6 traffic over a GRE Tunnel

Hello,
We have two 3825 routers with Advanced Enterprise IOS 12.4.9(T). Each of them serves many IPv4 (private and public) and IPv6 networks on their respective site.
We have created a wireless link between the two, using 4 wireless devices, with IP Addresses 10.10.2.2, 3, 4, 5 respectively (1 and 6 are the two end Ethernet interfaces on the routers).
Then we created a GRE tunnel over this link using addresses 172.16.1.1 and 2 (for the two ends) to route traffic over this link.
Now we want to route IPv6 traffic over the same link. However, we found that simply routing the IPv6 traffic over the above GRE / IP tunnel did not work.
Questions:
Is there a way we can use the same (GRE / IP) tunnel to transport both IPv4 and IPv6 traffic?
If not, can we setup two GRE tunnels over the same wireless link, that is, one GRE / IP for IPv4 traffic and a second one GRE / IPv6 for IPv6 traffic?
In brief, what is the suggested way to transport IPv4 and IPv6 traffic over the aforementioned (wireless) link?
I have read http://www.cisco.com/c/en/us/td/docs/ios/12_4/interface/configuration/guide/inb_tun.html#wp1061361 and other Internet material, however I am still confused.
Please help.
Thanks in advance,
Nick

We have set up two tunnels over the same link, one GRE / IP for the IPv4 traffic and one IPv6 / IP ("manual") for the IPv6 traffic. This setup seems to be working OK.
If there are other suggestions, please advise.
Thanks,
Nick

ZBF in a mixed ipv4 and ipv6 environment, don't touch ipv4

I have a dual stacked router for both ipv4 and ipv6. Ipv4 traffic should pass the zbf untouched due to the fact that there is another rock solid ipv4 firewall egress of the inside Interface. Is there a way that a class map like this could function on ipv6 traffic only?:
class-map type inspect match-any fullproto
description Permitted Traffic to internet
match protocol http
match protocol https
match protocol dns
match protocol imaps
match protocol icmp
match protocol ftp
match protocol ntp
match protocol rtsp
match protocol realmedia
match protocol netshow
match protocol appleqtc
match protocol streamworks
match protocol vdolive
match protocol ssh
match protocol user-rdp
So far there is only a CBAC solution in place for ipv6.
I'm showing my Interfaces:
interface FastEthernet0/0
description *** Inside IPV6 ***
no ip address
speed auto
full-duplex
ipv6 address FE80::1 link-local
ipv6 address ????:????:????:10::1/64
ipv6 nd other-config-flag
ipv6 dhcp relay destination ?:?:?:10::12
ipv6 traffic-filter inne6-inn in
no cdp enable
no mop enabled
interface FastEthernet0/0.4
description *** Inside IPV4 ***
encapsulation dot1Q 4
ip address 82.?.?.129 255.255.255.248
no cdp enable
interface FastEthernet0/1
description *** Outside ***
ip address 82.?.?.42 255.255.255.252
no ip redirects
no ip unreachables
no ip proxy-arp
speed auto
full-duplex
ipv6 address FE80::2 link-local
ipv6 address ?:599::2/126
ipv6 enable
ipv6 nd prefix default no-advertise
ipv6 nd prefix ?:599::/126 no-advertise
ipv6 nd managed-config-flag
ipv6 nd other-config-flag
ipv6 nd router-preference High
ipv6 inspect ipv6-cbac out
ipv6 traffic-filter ut-inn6 in
no cdp enable
no mop enabled
Please advise.
Regards,
Henning

I didn't test it, but what about the following:
Configure a new class-map where you match on an ipv6 access-list "any to any"
Configure a third class map of type ""match all" where you match on your "fullproto" class-map and also the above ipv6 class-map. For this class map you configure your inspections.
For ipv4-traffic you configure a class with a "pass" action in both directions.

EA4500 loses IPv4 and IPv6 information

No changes made but router will lose all information for IPv connectivity. I have paid twice to support to fix this issue and it still occurs every few months.
I tried rebooting router, and doing an IP Release/ Renew and router does not get IP address. I'd prefer not to have to pay again to fix this router. Any ideas?

Sorry - thought I had info:
I don't see anything on the router indicating a model other than EA4500. There is a serial number. Its plugged directly into a
Toshiba PCX2500 modem. If I connect my PC directly to the modem I have internet.
The router maintains all settings that Cisco helped me set up before except there are not IPv4 or IPv6 settings. I have screen shots from the setup. The Cisco rep had to clone the MAC of the modem to get the router to work. (Admin tab).
I unplugged modem and router and rebooted each. Everything appears to come up normally except for no IPv4/6 settings. I tried a release/renew but those settings stay blank.
I have internal network connectivity with the router, just no internet. I use Road Runner. I have a second network also on Road Runner but on a different modum and domain that is working fine. Unfortunately I have hard wired connections and kids games that rely on the EA4500

New iMac, migrated from macbook and now mail won't work. Tried re-installing operating system, still doesn't work. Can anyone help me to get mail working? thanks

I just bought a new iMac and I thought that it would be simple to migrate from my MacBook.
I have a time machine back-up so I decided to migrate using that. Everything seemed to instal pretty well with the exception of mail. To begin with I had 2 mail icons, then I started to read some forums and checked that i had the one I wanted in the applications folder, deleted the other and then downloaded the new operating system. Mail had to be force quit first and even when the download was complete Mail still wouldn't open or run. The only thing I can do is compose a new message, but I can't see my inbox at all.
It's really frustrating and I would love to know in a simple step by step guide how to get mail up and running with my existing migrated emails in it.
If anyone can give me some advice that would be great.
thanks in advance.
H

Problems such as yours are sometimes caused by files that should belong to you but are locked or have wrong permissions. This procedure will check for such files. It makes no changes and therefore will not, in itself, solve your problem.
First, empty the Trash.
Triple-click the line below to select it, then copy the selected text to the Clipboard (command-C):
find ~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 -o -acl $ 2> /dev/null | wc -l
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window (command-V). The command may take a noticeable amount of time to run. Wait for a new line ending in a dollar sign (“$”) to appear.
The output of this command, on a line directly below what you entered, will be a number such as "41." Please post it in a reply.

How to configure a COM domain, IPv4 and IPv6

Hi,
I am a new user on the Mac Server, but I have experience in Linux, my problem would be to understand how I configure the Mac Mini Server during installation or after installation, to assign a COM domain.
I would like to configure only the service Apache, FTP, MySQL.
My internet provider, today provided me 4 static IPs IPv4 and 4 IPv6, to use, now I want also to configure two local DNS if possible:
IPv4:
www.mydomain.com
ftp.mydomain.com
mysql.mydomain.com
IPv6:
www6.mydomain.com
For if I can configure DNS in Dual Stack or if I have to record them in a different way.
A control panel is currently not able to find it, you can advise me if something is well accepted, the important it is for business use as I would like to configure the server is for private use.
I hope I was clear, I'm sorry but I do not speak perfect English.
Thanks in advance to all.

To be clear, in your example you only have one domain - mydomain.com - all the other entries are just host records within that domain.
For your IPv4 hosts just add standard A records:
ftp A 1.2.3.4
www A 1.2.3.5
mysql A 1.2.3.6
For your IPv6 hosts just add AAAA records:
www6 AAAA 1234::ab:cd:ef
I seriously doubt you want to put your MySQL server on a public IP address, though, so I'd look carefully at your network setup before going much further.

HT204655 How to have a unified Photos Library after migrated from iPhoto and Aperture?

The "HT204655: Get started with Photos for OS X" do not help. If you have previously used iPhoto and Aperture, when you "migrate" the iPhoto, then follow the steps to "migrate" the Aperture library, you end up with 5 files in your Pictures folder: Photos Library (from iPhoto), Photos Library 2(from Aperture), iPhoto Library (Not sure if can be deleted or not - of course no), Aperture Library (for some reason blank), Aperture Library 2 (Created by Photos?).
So, looks like a mess and no easy way to make a clean migration.
I've a hope that exists a solution to have a single Photos Library with the merged iPhoto and Aperture contents, like a real migration.
If I export everything (From iPhoto and Aperture) then import in the Photos in a single Library should work, but will lose all the organization, faces, etc...

You could merge libraries with iPhoto Library Manager, but I never tried this for merging Aperture 3 libraries with iPhoto 8.
Are you planning to keep all your photos in iCloud? Then consider to merge them in iCloud, but it will take a long time.
Are you using iCloud Photo Library (Beta) and have enough iCloud storage for the merged library?
Wait, till your current Photos Library has been completely uploaded to iCloud.
Then quit Photos, and launch it again, while holding down the alt/options key. Select the old iPhoto lIbrary.
When the upgrade of the old library has been finished, make this library the System Photos library (in the Photos Preferences > General).
Enable again iCloud Photo Library (Beta) in the Photos > iCloud preferences.
Now Photos will upload the new library to iCloud as well and create a merged library in iCloud. After this merged library synced with your Mac, you will have a merged Photos library.

Migration from 2007 and Archive Mailbox PST import question

Our enterprise will be migrating from Exchange 2007 SP3 to Exchange 2013 CU3 very shortly. Exchange 2013 is set up and I am in coexistance mode currently. Everything is working fine with the legacy redirection, I have tested some mailbox migrations and they
work fine. We currently use Mimosa Nearpoint as a third party email archive product.
As part of this migration from 2007 to 2013, we plan on moving away from Mimosa Nearpoint and utilizing the Exchange 2013 Archive Mailbox feature. We will give each user an Archive Mailbox. We have the ability to export the users existing archive out of
NearPoint to .PST files and then migrating them directly into the users Archive Mailbox using the "New-MailboxImportRequest -IsArchive" powershell commandlet. This has been tested and works fine with one very important exception.
When I export from Nearpoint, I have to export the entire contents of the archive, I cannot set date ranges. So when I do an export, it also contains the contents of the user's mailbox. I have managed folder policies in place in the Exchange 2007 environment
which delete all contents of the mailbox older than 60 days, but when I import the .PST to the archive, it imports ALL items into the Archive Mailbox. So I have 60 days worth duplication of items.
It is my understanding that if I imported the Archive .PST directly into the users production mailbox in the 2013 side, that it would not import duplicate items. I am trying to find out if there is any process which will do the same thing with me importing
directly into the users Archive Mailbox.
Thanks you,

Hi,
We used a third patry email archive product to export to .pst files, so it is too hard to say that whether it cause this issue.
However, I found a method to delete the duplicate items from our mailbox via MFCMAPI Tool.
Please make sure that the Exchange Server mailbox has been backed up first.
Details in the following KB:
How to remove duplicate folders in Outlook when connected to an Exchange Server mailbox
http://support.microsoft.com/kb/2509983
I also found a script to remove duplicate items.
This script will scan each folder of a given mailbox and removes duplicate items from those folders. You can specify how the items should be deleted and what items to process, e.g. mail items or appointments. Sample usage is after a misbehaving synchronization
tool creates duplicate items or (accidental) import of PST file with duplicate items.
*****Please also make a full back up first*****
Removing Duplicate Items from a Mailbox
http://gallery.technet.microsoft.com/office/Removing-Duplicate-Items-f706e1cc#content
Disclaimer
The sample scripts are not supported under any Microsoft standard support program or service.
The sample scripts are provided AS IS without warranty of any kind. Microsoft further disclaims all implied warranties including, without limitation, any implied warranties of merchantability or of fitness for a particular purpose.
The entire risk arising out of the use or performance of the sample scripts and documentation remains with you.
In no event shall Microsoft, its authors, or anyone else involved in the creation, production, or delivery of the scripts be liable for any damages whatsoever (including, without limitation, damages for loss of business profits, business interruption, loss
of business information, or other pecuniary loss) arising out of the use of or inability to use the sample scripts or documentation, even if Microsoft has been advised of the possibility of such damages.
Hope it is helpful
Thanks
Mavis
Mavis Huang
TechNet Community Support

Migration from Zos and DB2 to Unix and UDB

We will be migrating our CRM application from mainframe and DB2 to a Unix environment with UDB.
Do you have any experience and/or guidelines ?
Thanks
Ronny

Hi Ronny,
I guess the right forum to post this question is SAP CRM: Webclient UI - Framework
Thanks and Regards,
santo.

CRM Migration from Zos and DB2 to Unix and UDB

We will be migrating our CRM application from mainframe and DB2 to a Unix environment with UDB.
Do you have any experience and/or guidelines ?
Thanks
Ronny

Hi Ronny,
I guess the right forum to post this question is SAP CRM: Webclient UI - Framework
Thanks and Regards,
santo.

MPLS migration from IPv4 and IPv6

Similar Messages

Maybe you are looking for