MSI KT4 Ultra-FISR

Recent upgrade problem
Old: MSI kt266 pro-2, allied 300w atx psu, ati radeon ve 32m
New: MSI kt4 ultra-fisr, allied 400w atx psu, MSI geforce4 mx440-vtp, western digital 80g hdd
Unchanged: 256m pc2700 ddr, top-g 24-10-40x cdrw, maxtor 45g hdd, sblive platinum
Problem: After upgrading I have difficulty installing software by cd. Errors are spomething like (bad cab file)
occasional but random reboots
moving files on hdd causes reboots
can someone help? I've contacted MSI about it and really hope  I won't have to send the board in as defective if it really isn't.. thanks

Hi,
I have the same issues with my KT4 Ultra (pure version).
Running GF4 Ti4400, Athlon XP2400+ etc, 450W power etc. There are quite many posts of similar issues all over the Via Arena forums and some here as well. KT4 Ultra's and KT4V's seem to be the boards affected.
Installing the Via USB Filter Patch helped with narrowing down the number of crashes and some of the errors.
(note: disable automatic restart from 'Startup and Recovery settings' to see the driver that crashes)
Link to Via Arena FTP site
I had a K7T266pro2-RU board before this which worked 100% stable. I've tested all my components which are fine. Tested different power supplies, memory. Still, continuous random errors after many times of reinstalling Win2K by the book and with default bios settings.
Sometimes the setup works fine for a week and then starts to mess around again.
Looks like setting the cpu fsb down to 128 MHz from 133 MHz solves the issues, so try that and report back.
Also check the filter patch.
I'm personally waiting for the next bios release to fix these issues - if not, I'm showing this board RMA and go to nForce2 chipset.
I also tested the 1.25 beta bios, which gave me lots of crashes during Win2K boot -> flashed back to v1.10 and booting works again.
- Tom

Similar Messages

  • Upgrading to a MSI kt4-ultra FISR board.....

    Currently I've got a gigabyte motherboard and I want to upgrade to an: MSI kt4-ultra FISR board. Can I just pull my old board out and install the MSI board with all my old hardware, O/S already on harddrive -  and do a start up, or will I run into errors and problems when I try this? Currently my system looks like this:
    1)  Case: "Xaser SC5000BWII"  400watt mid-tower case        
    2)  Motherboard: Gigabyte GA-7DXR DDR+Raid
    3)  CPU Chip:   AMD Athon XP 1800 1.6Ghz
    4)  Memory:  512 of  PC2100 DDR266 Memory                  
    5)  AudioCard:  Creative SoundBlaster Audigy MP3 card
    6)  VideoCard:  ATI RADEON 9000pro, 128 DDR
    7)  Hard Drive:  Maxtor 80GB 7200RPM ATA-133 "D740X" Mdl:6L080J4
    8) Operating System:  Ms Windows XP Pro
              Thanks for the help........ seboyd ?(  :D  8)

    A clean install will give you 30 days to reactivate and it only takes a 5 minute call to get the new #s. Pretty simple and much easier than trying to straighten out all the error codes from old O S. I did however move an XP harddrive from a Turbo2 to a KT4 without a new install but they were both MSI boards. A clean install also gets rid of all the junk that accumulates. Just enter bios and make the CD rom 1 st boot . BIGDADDY51 CT. USA  :D  8)  :D

  • Serial ATA on MSI KT4 Ultra FISR??

    Hello
    Just a general query here about Serial ATA on the 6590 board (KT4 Ultra FISR).
    I am hoping to build a system with this board and was hoping to start with only one HD, preferably an 80Gb Serial ATA drive.  Does the promise raid controller on this board allow you to boot on a single serial ATA drive?
    P.S.  I was also hoping to add a Radeon 9700 card (not pro) but have read about many problems within this forum.  Does anyone know if the problems have been cleared?
    Thanks
     ?(

    Well, my idea was to buy a Serial ATA drive from the outset and use it as the only HD in the system.  Therefore, it would have to start on the serial ATA raid port.
    The only other boot option I can see which may be relevant is "Legacy SCSI".  Doesn't sound right though.  There are also a lot of BBS (BIOS boot specification) choices from 0 to 9 but I dont know what they are.
    There are about 25 boot options including from USB CDROM drives but nothing specific to RAID!

  • MSI KT4 Ultra-FISR MS-6590 Won\'t Boot-Up

    Ok I just install my new system today. I took my time and did everything right. So when I started my system up, it came on for about 5 seconds then shut off. I spent endless hours trying figure out the problem but to no avail. Then I came here and read other people's problem to help me out. I already read the trouble shooting guide but none of that helped. Here are my system specs.
    duron 1.3
    256MB ddr 2100
    inddo gf4 440se
    16x dvd
    40/16/48 cd burner
    2 20 gig harddrives
    350 psu
    my dc is 3.3v
    my max combine is 175
    I know it's not a power issue beacuse I unplugged everything but the cpu and on harddrive, and I still get the same problem. Even if I just have the cpu, it will not boot up. Please help!!!! ;(

    at least 200 with a gf4,you might get away with a tiny bit as only a duron,but 185 is the least we say for a normal system
    if 14a 3.3 like last guy no hope at all

  • KT4 Ultra FISR and Radeon 9700pro

    OK, I upgraded my MB from the k7t266pro to an Kt4 Ultra.  I also upgraded to an AMD xp 2500+ and new DDR 333 ram.  My video card is the ati 9700pro.  This card functioned just fine with my old board as I never crashed.
    Since I have upgraded I have not been able to play any 3d games!!  all the games start and are playable for 2-5 mins then it just completely freezes my system.  i cannot even do an end task and have to hit the reset button to restart the PC.
    I am running Winxp home edition and am fully patched.  I have also upgraded the bios and installed every new driver from the live update utility.  i have the latest drivers available from ATI as well.  
    what gives here?  I have searched Google and various other sites and i have run across many many threads with people having identical problems with this board and video card.  my thought is that it is not the video card, as it ran flawlessly on my old MSI board.  i do PC support and system admin for a living and 99% of the time I can resolve PC problems on my own, however, I am at a loss with this one.  I have been a loyal MSI customer as this is the 4th MB i have bought from you guys over the years, but i can't help feeling disappointed right now.  any ideas?  This stinks as I was so looking forward to the upgrade in performance and now i got jack.
    Tabascodog
    System info:
    MSI KT4 Ultra FISR
    ATI 9700pro
    512 DDR 2700 Ram
    300w PS (AMD approved)
    Maxtor 30bg ata 133

    I took the advice of some of you and got a Antec 430w TruePower PS to replace my old one.  Still no good.  I was a little skeptical about the new PS thing since I run a pretty minimal configuration.
    MSI KT4 Ultra - fisr
    AMD XP2500+
    Radeon 9700pro
    512mb 333DDR Ram
    30BG Maxtor HD 133ata
    Creative PC-DVD Drive
    1 Generic Floppy
    As you can see, pretty sparse.  I soley use this box as a gaming type PC, so I try and keep the load light.  At this point I think I would like the board replaced.  Like I said, the 9700pro worked like a champ on my k7t266 pro, I doubt it is the new AMD CPU... so that leaves just the memory or the board at this point.  I mean, driver wise I am using the same drivers as those that do not have problems.  I am going to buy some high-end memory to eliminate that issue, but I highly doubt that will make the difference.  I hope I'm wrong though.
    Oh, BTW the option to change the AGP slot back to 4x is locked out for some reason.  That kinda pisses me off too.  I mean, at least give me the option to bring it back down to 4x.
    Tabascodog

  • KT4 ULtra FISR - HD install probs

    okay - I have just built my new system -
    Athlon XP 2400+
    MSI KT4 Ultra FISR
    512MB Samsung DDR400 (MSI Approved)
    ATI Radeon 7500
    Hercules Digifire 7.1
    Seadate Barracuda 80GB
    Pioneer DVD-RW 104
    Liteon CD-RW 20x
    My problem is - that the HD is new, formatted - when I make the Pioneer the 1st boot device, winXP starts to install - however after it puts the initial set of files onto the HD - it has to restart - and when it does I get this msg:
    "Windows could not start because of a computer disk hardware configuration problem. Could not read from the selected boot disk. Check boot path and disk hardware.
    Please check the windows documentation about hardware......."
    I initially tried it with a 120GB Maxtor drive and got the same msg. Nothing is wrong with either drive - because they are both brand new, and properly formatted.
    I am not using the RAID option I just want to have two HD's connected to IDE1 as master/slave.
    When I go into the BIOS - in the boot options my CD drives and HD shows in the correct order. So if it can see my HD in the BIOS - why can't I boot up and complete the installation?
    Do I have to disable something in the BIOS - there is a RIAD controller check just after the BIOS splash screen and then it goes onto say that the no drivers were found - so then it carries on with all the other checks and then stops with the above error message.
    Somebody please tell me how I can get it to locate my HD and complete the installation of the OS?
    Thank you

    sorry i guess i wasn't that clear - my optical drives are on IDE2 - IDE1 only has my Seagate HD - only when this is up and running will i add the maxtor as a slave to IDE1
    so still looking for that solution

  • KT4-ULTRA FISR NO LAN DETECT

    I have this problem:
    in the bios at
    Integrated Perimetrals > OnBoard PCI Controller
    1. Serial Ata Controller
    2. 1394 Controller
    3. Audio Controller
    the lan controller???  
    I dont see...?? ?(
    I have canghed the bios from version 1.2 to version 1.3 and from 1.3. to 1.2 but the Lan controller dont see...!
    why the problem?? the chip Broadcom is on board... but dont work!!
    my configuration are:
    - MSI KT4-Ultra FISR whit bluetooth module bios 1.3
    - AMD Athlon XP 2400+
    - 512 MB DDR333 Geil ULTRa Cs 2
    - SK Video ASUS V8200 Dlx Ti500
    - 1 hdd 40 GB Ata 133 P.M.
    - 1 hdd 80 GB Ata 133 P.S.
    - 1 hdd 60 GB Ata 133 Ata Raid
    - 1 DVD rom S.M.
    - 1 Yamaha F1 S.S.
    Bye...!
    Excuseme for my english I'm Italian and speak so so the language...

    Okay, I assume the new 1.4 bios they are working on will address this problem? Or perhaps not? This problem as I see has been discovered last year, yet how many bios updates were released since? None of them remidying this situation.
    The KT4 Ultra FISR is a really nice mainboard, but the lack of support and/or broken LAN controller really makes it look bad.
    Flashing the bios and clearing the cmos simply wont work. This shouldnt be necessary when the LAN just dissapears on its own without any cause. If it isnt a bios bug, then its clearly a board flaw.
    Is that why this problem has been covered up quite well? If there hasent been a bios fix, then i would guess that it is a flaw that is still not being publicly made by MSI themselves.
    If theres a known fault with a product, i expect to be known about it. This problem has shown up enough to be a known flaw.
    No, checking the winblows "device manager/tackler" wont show it, clearing the cmos wont show it, flashing the bios 10000 times wont make it show either. The device doesnt even exist on the mainboards pci table, its gone, not there, poof, kapoot, vanished.
    PCI devices found:
      Bus  0, device   0, function  0:
        Host bridge: VIA Technologies, Inc. VT8377 [KT400 AGP] Host Bridge (rev 0).
          Master Capable.  Latency=8.  
          Prefetchable 32 bit memory at 0xe0000000 [0xefffffff].
      Bus  0, device   1, function  0:
        PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge (rev 0).
          Master Capable.  No bursts.  Min Gnt=12.
      Bus  0, device   7, function  0:
        Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 16).
          IRQ 10.
          Master Capable.  Latency=32.  Min Gnt=32.Max Lat=64.
          I/O at 0xec00 [0xecff].
          Non-prefetchable 32 bit memory at 0xdfffff00 [0xdfffffff].
      Bus  0, device  12, function  0:
        Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 16).
          IRQ 11.
          Master Capable.  Latency=32.  Min Gnt=2.Max Lat=24.
          I/O at 0xe800 [0xe8ff].
      Bus  0, device  16, function  0:
        USB Controller: VIA Technologies, Inc. USB (rev 128).
          IRQ 11.
          Master Capable.  Latency=32.  
          I/O at 0xdc00 [0xdc1f].
      Bus  0, device  16, function  1:
        USB Controller: VIA Technologies, Inc. USB (#2) (rev 128).
          IRQ 5.
          Master Capable.  Latency=32.  
          I/O at 0xe000 [0xe01f].
      Bus  0, device  16, function  2:
        USB Controller: VIA Technologies, Inc. USB (#3) (rev 128).
          IRQ 12.
          Master Capable.  Latency=32.  
          I/O at 0xe400 [0xe41f].
      Bus  0, device  16, function  3:
        USB Controller: VIA Technologies, Inc. USB 2.0 (rev 130).
          IRQ 10.
          Master Capable.  Latency=32.  
          Non-prefetchable 32 bit memory at 0xdffffe00 [0xdffffeff].
      Bus  0, device  17, function  0:
        ISA bridge: VIA Technologies, Inc. VT8233A ISA Bridge (rev 0).
      Bus  0, device  17, function  1:
        IDE interface: VIA Technologies, Inc. VT82C586B PIPC Bus Master IDE (rev 6).
          IRQ 14.
          Master Capable.  Latency=32.  
          I/O at 0xfc00 [0xfc0f].
      Bus  1, device   0, function  0:
        VGA compatible controller: PCI device 1002:514d (ATI Technologies Inc) (rev 0).
          IRQ 11.
          Master Capable.  Latency=32.  Min Gnt=8.
          Prefetchable 32 bit memory at 0xc0000000 [0xcfffffff].
          I/O at 0xc800 [0xc8ff].
          Non-prefetchable 32 bit memory at 0xdfef0000 [0xdfefffff].
    Hello?? Anybody home? Think Mcfly think!
    edit:
    Yes the IEEE1394 and RAID controller isnt there, thats because it is disabled in the bios, and can be reenabled just as easily, unlike the Broadcom LAN controller, that isnt even there to enable anyways.

  • KT4-Ultra FISR no longer supported?

    Hey all, I was trying to find the Bios/driver updates/manual for this board, the MSI KT4-Ultra FISR.  Can anyone link me?  I can't seem to find it.
    Thanks.

    You will find the KT4 Ultra in the archives section here:- http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=356 The bios, driver and manual links can be found on the left of your screen.

  • KT4 Ultra FISR

    Hey, I am new to these forums. Thought I would drop by and see if I can get some help with a new mobo I had just purchased.
    I just purchased an MSI KT4 Ultra FISR. AMD 3200+ Capatible and allows for 400mhz memory to be placed.
    I am going to purchase an AMD XP3200 Barton chip soon and would like to use the new type of memory. Either XP2700 (2x512mb @ 333mhz) or XP3200 (1x512 @400mhz). Ok... now for my question. I have been to MSI homepage and read the specs on this specific motherboard. It states that I can only use 1 stick of XP3200 (400mhz type) memory at 2 channels. Does anyone have this board and ever tried running it with XP3200 (2x512 @ 400mhz) totalling 1Ghz @ 400mhz?
    Also will the XP3200+ operate with XP2700 memory running at 333mhz? Dumb question. I know.
    Ya... if anyone has any suggestions as what I can do to mod this board feel free to let me know.
    Another note... while looking through the product line MSI does not show it is carrying the KT4 Ultra FISR anymore.. Any reason as to why or is it now calld by another name?

    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_list.php?kind=1&CHIP=4&NAME=Socket%20A
    its in the archive as via now make a 400a chipset so msi sell the new one now
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=442
    yours is here
    http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=356

  • KT4 Ultra FISR and WD Raptor 74GB problems

    MSI KT4 Ultra FISR - MS6590
    Western Digital Raptor 74GB 10,000rpm - WD740
    Is it possible on the MS6590 to have a SATA drive on Ser1 but nothing on EIDE or Ser2? The reason I ask is that, I cannot get the drive to show in BIOS under "Standard CMOS". Thanks any help is appreciated.

    ..." I'll post my power supply specs in about an hour..."
    Hey ! How many minutes have an hour in your country ?  

  • No Sound with KT4 Ultra - FISR -- HELP!

    hey
    I got a KT4 Ultra - FISR along with and XP 2400 and other goodies for christmas. I put the machine together and installed 98se, and all of the included drivers the came on the MSI Utilities disk. Everything was working perfectly with it (got 11752 on 3dmark 2001, is that a decent score?) anyways everything was cool except the on-board c-media sound was not working at all.  ?(  I have 2 speakers w/ sub and i have them plugged into the line out spot in the mobo. I have turned the sound on in my BIOS and messed with all the sound settings in windows and still i get no sound at all. I even unplugged the bracket that came with it for surround because i saw it could possibly cause some problems. I then checked all my connections and still no sound.  X( I was woundering if there are any other settings or jumpers that i need to set for my sound to work. Any additional information on how to get my sound to work would be greately appreciated. My system specs are below. Thankz  
    MSI KT4 Ultra-FISR
    AMD XP 2400+
    MSI GF4 TI 4400
    256 MB GeIL PC2700
    120 GB Maxtor ATA/133
    ASUS 48/16/48 CD-RW
    Pioneer 16x DVD
    Hyperion 4in1
    Win 98se

    bump

  • KT4 Ultra-FISR MSI UTILITIES DON\'T WORK

    Hello all i have buyed a KT4-Ultra-FISR , instaled it withou any problems with a Athlon XP 2400+ and Windows XP PRO, the only problem is that the MSI utilities don't work, i have tried PCalert4 and fuzzylogic, and both put my cpu running at 100% and don´t work, they don´t even close with ctrl+alt+del, and shuting down program, i have to sut down the computer to close them, the new version of pcalert show the following message "no hardware monitor", if i use the program Speedfan, it work well, can anyone help me? my bios is the v 1.1
    ==================
    My System
    ==================
    KT4-Ultra-FISR
    Athlon XP 2400+
    256 DDR 333 Apacer
    80g Maxtor Diamond Max+ 133 7200
    G-force 4 MX 440 64 DDR
    Pioneer DVD 16x
    Plextor CD-RW 40x12X40
    CPU Cooler Thermaltake Volcano 7

    I have used the latest version of the utilities from MSI website and tey don´t work, but as i said before if i use Speedfan 4.07, it work fine, can this be a problem of the bios? i still have the original version (v 1.1), should i update the bios?
    Quote
    Originally posted by SebX
    Did you updated utilities from MSI WWW page ???
    Did other monitoring software like MBM 5 work corectly ???
    Try MBM 5 if it works , download updated utilities from MSI web site ....

  • KT4 Ultra FISR "accessories"

    I purchased a bare bones KT4 Ultra FISR board from Newegg.com ?(  and wanted to know how I can purchase the special backplate and get info on the 1394 bracket.
    Anyone know?  I wrote to MSI but they did  not answer my email.
    Thank you!
    Eric

    These brackets were hard to get..... I guess somebody had mentioned it. Please use the forum search function and hunt for the answer. Good luck.
    My another suggestion is to get a good PC casing with IEEE1394 ports and USB ports in front. You can make full use of these ports

  • KT4 Ultra FISR AGP Speed Problem

    Hi all,
    I've got a bit of a problem and was wondering if someone can help?
    I have bought the KT4 Ultra FISR and am having a problem when trying to use it with my 8x AGP Nvidia ge Force 4 ti 4200 but the bois wont let me change the AGP speed to 8x, it insists that the highest it can go is 4x.  ;(
    I have run the newest 3DMark03 and it's showing that my AGP is only 2.0 and not the 3.0 that is meant to be with the board?
    I was wondering if this is the problem?
    I have double checked with the Graphics Card Manufacturer and they have confirmed that my card is an 8x card and I know that it was running at 8x on my last board.
    I have done all of the Auto updates on the MSI motherbaord update utility but there's still no joy.
    Any help would be greatly appreciated!!
    - Ricky

    Hi there
    Well I have the Inno36 Ti 4200 8x AGP card:
    http://www.ivmm.com/inno3d/geforce4/products_gf4_ti_agp8x_reviews.html
    I know it's not the best card on the market but it should still be able to operate at it's advertised speed :P
    A couple of the guys here at EA bought the card and theres are working fine on thier boards :(
    I am not totally sure of the version number of my bios but does 1.3 ring a bell?
    I wont be able to check the version till monday...
    Like I said before.. I did notice that 3dmark03 noted that I was using agp 2.0, is that right?
    - Ricky
    P.s. Thankyou for taking the time to help me out Its much appreciated.

  • KT4 Ultra - FISR = Bluetooth or not?

    I have a KT4 Ultra FISR motherboard.. Do I need anything else to make bluetooth work or not.. I've seen several threads that say this board does not need any antenna because one of the USB headers has it built in.. I've hooked it up to the motherboard as it says.. Yet, even after installing the Bluetooth software from MSI's site it dosen't show up under device manager at all. And it dosen't find my Sony T68i phone either. Am I supposed to have something else, to make this work? Like I said, I have no antenna or card that I got with the mobo, should I have?

    At our local shop that sells a lot of msi mobos, the bluetooth mobos have the antenna and module in a seperate box taped to the mobo box. I think that is probably the way they are meant to be sold, I asked and they said that is how they come. I think some retailers may be taking the bluetooth module and antenna box off and selling it seperate from the mobo, I would call and asked the place you bought it from. This seems to be a widespread issue.

Maybe you are looking for