My iPad fell one night from one side (left) and now its border from the inside or the main screen border (left side- portrait) is thicker on the other side (right side) like it moved left when it fell :(( so sad this is a gift from my mother. please help
my iPad fell one night from one side (left) and now its border from the inside or the main screen border (left side- portrait) is thicker on the other side (right side) like it moved left when it fell :(( so sad this is a gift from my mother. please help
thank you. it just annoys me and im scared that my mom would notice it coz she bought it for me..
Similar Messages
-
i have not used ipad from last 1 year and now its not starting any suggestion how to start,
Using the Supplied iPad charger, Connect it to the mains for at least 60 minutes...
Then try to turn it on. -
My ipad wont work. it ran out of batteries and now its stuck on the apple logo
i just got my ipad less than two weeks ago, and i went to sleep with it on 27% charged. when i woke up it was out of batterie so i plugged it in, but it got stuck on the apple logo with the swirly thing and when i plug it in again, it just keeps making the 'bing' sound over and over again. what do i do?
Using the Charger that came with your iPad... Connect it to the Mains for at least 30 - 40 minutes...
Then try a reset...
Reset ( No Data will be Lost )
Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
http://support.apple.com/kb/ht1430 -
hi my name is Aditya. i am using ipad 2. 2 days ago my ipad fall down from my hand and now its screen is not working it is totally blank but shocking thing is that when i take a screen shot the display came back for 2-3 second. dose ne 1 have same problem....?
Anyone have any suggestions? or is everyone else just as clueless as me !
-
I lost my ipod touch when i moved flats and i just found it in one of the boxes after 4months and now its asking me to "connect to itunes" but itunes doesnt recognize it because i have a passcode and its asking me to enter it. HEEEEELP please
Place the iPod in Recovery Mode and restore via iTunes.
iOS: Wrong passcode results in red disabled screen
If not successful, try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings -
I bought my iphone 5s a week before and now its volume "up" button is not working when pressed.Does anybody know what to do to make it work?I have a one year warranty.Should i give it to apple retail shop or is there any way to solve this problem?
IF it is a manufacturing defect and you bought the device from Apple or an authorized Apple retailer, then take it into Apple.
-
I run Tiger OSX on one MacBook and SnowLeopard on another. Photos were downloaded from Tiger to SnowLeopard, and now iPhoto won't open on the Tiger Mac. Will upgrading iPhoto fix this problem?
What matters is the version of iPhoto you have on the different machines. Can you tell us what they are, and what exact error message you get.
Regards
TD -
my phone suddly switched off and now its not switching on can any one help me when it swithch off my phone battery was full.
Which apps do you open acouse iphone switched off? You can try to reset iPhone.
-
Last night I did an update and now when I turn on my macbook it just goes to the white screen with the apple and stays like that. How do I fix this issue?
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
i just downloaded two rental movies from the iTunes store, proceeded to sync them to my iPad, and now I can't find where they landed. Anybody know where to access rental movies on the iPad? thanks
And just in case .... You don't actually sync rental movies to the iPad....
To transfer a rented movie from iTunes, use the movies pane in iTunes. Rented movies transfer is at the top. You must have an Internet connection to transfer a rented movie. Select the "move" arrow in the direction you wish to transfer, and click the apply button at the bottom right. Rented movies can only exist on one device at a time, they do not sync like other video, but move from iTunes to the iPad. -
I tried changing my password, and it changed to one that wasnt it, and i dont know it. So i tried it too many times and now its saying it is disabled, connect to itunes. but a problem is that my power button on top is broken. how to i fix it?
Disabled
Place the iOS device in Recovery Mode and then connect to your computer and restore via iTunes. The iPod will be erased.
iOS: Wrong passcode results in red disabled screen
If recovery mode does not work try DFU mode.
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
For how to restore:
iTunes: Restoring iOS software
To restore from backup see:
iOS: How to back up
If you restore from iCloud backup the apps will be automatically downloaded. If you restore from iTunes backup the apps and music have to be in the iTunes library since synced media like apps and music are not included in the backup of the iOS device that iTunes makes.
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store -
Help! I recently upgraded to OS 10.9.4 from 10.6.8, and now when I want to send an email to a group in my contacts I am no longer able to select the group as a whole. I have to select each address individually. This can't be right. With 10.6.8 I used to be able to double click on the name of the group and they would all be selected. I've also noticed that my address book is now called "contacts." Thanks in advance for your help.
Try these in order testing your system after each to see if it's back to normal:
1. a. Resetting your Mac's PRAM and NVRAM
b. Intel-based Macs: Resetting the System Management Controller (SMC)
2. Restart the computer in Safe Mode, then restart again, normally. If this doesn't help, then:
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the
COMMAND and R keys until the Utilities menu screen appears. Alternatively, restart the
computer and after the chime press and hold down the OPTION key until the boot manager
screen appears. Select the Recovery HD and click on the downward pointing arrow button.
3. Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the Utilities menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu. Select Restart from the Apple menu.
Reinstall the 10.9.4 update: OS X Mavericks 10.9.4 Update (Combo).
4. Reinstall Lion/Mountain Lion, Mavericks: Reboot from the Recovery HD. Select Reinstall Lion/Mountain Lion, Mavericks from the Utilities menu, and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
Reinstall the 10.9.4 update: OS X Mavericks 10.9.4 Update (Combo). -
mayday....I inadvertly erased my contacts when I deleted them from my old phone and now my contacts in my new phone is empty.
Welcome to the Apple Community.
Do you have a back up taken prior to deleting them.
To restore from a back up made through iTunes, follow these instructions.
To restore from a back up made through iCloud, try the following:
The difficulty in restoring iCloud data from a back up is that the back up is older than the current version on iCloud and anything that is restored gets removed again when an iCloud sync occurs.
Ensure the device is connected to your local network.
Start the restore from iCloud back up.
Allow the devices settings to restore (watch for the confirmation of completion).
As the apps begin to restore pull the connection to your router WAN port (the one that goes to the telephone point).
Wait for the time out confirmation.
Navigate to settings > iCloud and turn off contact syncing (keep contacts when prompted).
Reconnect the router to the internet and let the restore process complete.
Delete any iCloud contacts from iCloud.com on a computer.
Navigate to settings > iCloud and turn on contact syncing (merge contacts when prompted).
May I suggest that you carry out a back up to iTunes before you try anything, that way should things become even worse, you can at least restore back to where you are now. -
I just connect one monse to my MacBook Air and now my keybord is not working
I just connect one monse to my MacBook Air and now my keybord is not working
What to do?lrfrustrated wrote:
I just downloaded Adobe XI onto my macbook air and now I cannot save or print any PDF files. Will not let me do Print-Save as PDF, and if i do Save as i get a message saying that the file is corrupted. I had NO PROBLEMS at all doing this many times until i downloaded the new version. I have uninstalled and reinstalled, to no avail. I am super frustrated.
Print>Save as PDF - uses Preview (part of OS X), so Adobe Reader should have no effect on that at all.
As to the "damaged file" error, simply uninstalling the Reader app won't affect it. Do the following:
Mac HD/Library/Internet Plug-ins
Trash the AdobePDFViewer.plugin and AdobePDFViewerNPAPI.plugin files
Mac HD/Applications
Trash the Adobe Reader app
[user]/Library/Preferences
Trash the com.adobe.Reader.plist file
To access the [user]/Library, hold the "Option" key and click "Go" from the FInder menu.
Mac HD/Library/Application Support/Adobe
Trash the Reader folder (the whole folder)
Empty the Trash.
Download the FULL installer here: http://get.adobe.com/reader/enterprise/
Quit your browser and reinstall Reader.
Launch it from the Applications folder and accept the license agreement.
You should have no problems downloading PDFs with Safari.
Unfortunately, ANY PDF that says it's damaged.... is. You'll have to trash them. -
hi there , I have Ipad 2. just upgraded to OS 5.1 and now cant transfer any videos to it. videos already stored can be played but when i try to copy any new video, it says that the video cannot be played by Ipad.I have tried mp4, mov, m4v but nothing plays.
Log in to the Developer forum. You will find instructions on how to install the lastest beta. Your problem is the beta you have installed has expired. All of them did on October 5; you will find hundreds of threads discussing this. If you have a beta it is assumed that you will continue as a beta tester, so a simple update using iTunes will not work.
If you no longer want to be a beta tester install the GM 7.0.2 by restoring from iTunes using DFU mode.
Maybe you are looking for
-
Enable wireless doesn't work like expected
Hej, When I press my wireless-button on my laptop, a popup shows up saying "Wireless hardware enabled". However, I have to click the "Enable wireless" checkbox in the networkmanager applet to really enable wireless networking. I don't think this is h
-
Problem updating ovi store and downloading whatsap...
When i try to open ovi store on my x2-01 it tells me to update it before i would be able to download it and when i try it always tells me page not found.my other problem is when i try to download any software e.g whatsapp application using my phone i
-
How do I delete an itunes account w/o being able to log into the account?
Is there anyway short of paying apple to remove an itunes/apple id account? I can't access this account for various reasons.
-
Firewall constantly asks to authenticate for incoming connections
Hi, Apologies if this is nothing new, but I can't find a solution. EyeTV 3.1.2 on my MBP insists on asking on each and every launch whether I want "to accept incoming network connections." I do, I tell it so and have to authenticate. But the next tim
-
Hi Gurus, I am going to do a functional upgrade from 4.7C to ECC 6.0 (classic GL, not new GL). Can someone please list me the steps that I need to do to achieve the upgrade. I would be very grateful and would assign points as a gesture