No messages created from split mapping

Hello,
My Scenario is JDBC to Proxy and there is 1:n Mapping
I had done the multi mapping and done the all the necessary configuration in the MM, IM and ID
I tested the payload in the MM and IM and it is working fine.
But while iam doing the end to end testing in the ID --- Test Configuration,It is showing the error at Interface Determinmation and Mapping step.
In SXMB moni, iam getting error as
- 
- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="">
<SAP:Category>XIServer</SAP:Category>
<SAP:Code area="MAPPING">GENERIC</SAP:Code>
<SAP:P1>No messages created from split mapping</SAP:P1>
<SAP:P2 />
<SAP:P3 />
<SAP:P4 />
<SAP:AdditionalText />
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack>No messages created from split mapping</SAP:Stack>
<SAP:Retry>M</SAP:Retry>
</SAP:Error>
The below is my source payload.
<?xml version="1.0" encoding="utf-8" ?>
- <ns:mt_vendor_fusiondb xmlns:ns="http://loreal.com/poc_vendor">
- <row>
<ID>1</ID>
<LIFNR />
<NAME1>SriTest</NAME1>
<PSTLZ>07066</PSTLZ>
<LAND1>USA</LAND1>
<TELF1>1234567890</TELF1>
<Status>READY</Status>
<LastUpdated>2008-11-20 09:20:00.0</LastUpdated>
</row>
- <row>
<ID>2</ID>
<LIFNR />
<NAME1>GilderTest</NAME1>
<PSTLZ>07066</PSTLZ>
<LAND1>USA</LAND1>
<TELF1>1234567890</TELF1>
<Status>READY</Status>
<LastUpdated>2008-11-20 09:20:00.0</LastUpdated>
</row>
- <row>
<ID>3</ID>
<LIFNR />
<NAME1>KarthikTest</NAME1>
<PSTLZ>07066</PSTLZ>
<LAND1>USA</LAND1>
<TELF1>1234567890</TELF1>
<Status>READY</Status>
<LastUpdated>2008-11-20 09:20:00.0</LastUpdated>
</row>
</ns:mt_vendor_fusiondb>
Please help me in resolving this error
Srinivas

Hi Carlos,
Now my message mapping is working, the error is in the messagetype i declared 'row' as capital letters,due to this in the runtime it is erroring out in the request message mapping.
But still I had one more issue,iam getting error in Technical routing, the error is
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- 
- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="">
<SAP:Category>XIServer</SAP:Category>
<SAP:Code area="OUTBINDING">CO_TXT_MMF_ENGINETYPE</SAP:Code>
<SAP:P1 />
<SAP:P2 />
<SAP:P3 />
<SAP:P4 />
<SAP:AdditionalText />
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack>Messages in multi message format can be sent to one adapter engine only</SAP:Stack>
<SAP:Retry>M</SAP:Retry>
</SAP:Error>
In the ID i checked the radio button extended.
But still iam getting the above error.Can you guide me in resolving the error

Similar Messages

No messages created from split mapping - Multimapping

Hi,
Getting the error in MONI saying that : No messages created from split mapping
Sender is :
   <Purchase>
            <Number>007</Number>
            <Desc>RAJ</Desc>
            <Quantity>half</Quantity>
   </Purchase>
Target should be 3 files such as:
<Purchase>
            <Number>007</Number>
            <Desc>RAJ</Desc>
   </Purchase>
<Purchase>
            <Number>007</Number>
            <Quantity>half</Quantity>
/Purchase>
<Purchase>
             <Desc>RAJ</Desc>
            <Quantity>half</Quantity>
</Purchase>
Regards,
Y.Raj.

Hi,
In your mapping select the cardinality of source message as 0..1 while that of target message should be 0..unbounded.
Also since you are not using all the elements of source into all the target messages (seems using only two source elements in each target msg) do the mapping accordingly...i doubt whether you can achieve your requirement in one mapping itself....may be you will have to follow what Tarang mentioned:
3. have 3 mappings between source structure and MT1(map only num,dec), source struc and MT2(map num,Qty) ....
Exception to above statement:)
If you set the target cardinality as 0..unbounded then duplicate the root target node thrice (as per your requirement)....and then map each target section seperately....
Regards,
Abhishek.
Edited by: abhishek salvi on Apr 7, 2009 9:12 AM

No messages created from split mapping error .....

HI XI Friends..
In My XML to RFC scenario,,
i am doing message splitting withput BPM.
in message mapping ..i changed target message occurance to unbounded
and same i did in interface mapping also..
static test is OK..creating multiple target messages in static test.
in interface determination,using enhanced option i given interface mapping.
file is picking but in SXMB_MONI ...i am getting error like this
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- 
- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="">
<SAP:Category>XIServer</SAP:Category>
<SAP:Code area="MAPPING">GENERIC</SAP:Code>
<SAP:P1>No messages created from split mapping</SAP:P1>
<SAP:P2 />
<SAP:P3 />
<SAP:P4 />
<SAP:AdditionalText />
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack>No messages created from split mapping</SAP:Stack>
<SAP:Retry>M</SAP:Retry>
</SAP:Error>
please guide me..
regards
ram

Hi Ram,
Check these..
Split mapping created no messages
Message Split without BPM - Error
cheers,
Prashanth
P.S Please mark helpful answers

Accessing SAP:HopList element in message header from JAVA-mapping

Dear Experts,
Is it possible to access the SAP:HopList element from message header in JAVA-mapping?
I need this to get the list off all receivers of current message (I have a ReceiverDetermination with two receivers, without any conditions, so both receivers are receiving each message and in InterfaceDetermination to one of the receivers I have a JAVA-mapping, in which I need to know the name of another receiver. And the SAP:HopList is containing this information).
Or maybe where is some other solution?
Best Regards,
Artsiom Anichenka

That's tricky, since the proper way of doing it would be through BPM.
Anyway, if you expose your XI interface as a WebService (Soap sender cc) you could access it through Mapping Lookup (lookup works for RFC, DB and Soap lookups). Check https://help.sap.com/javadocs/NW04S/current/pi/index.html
But be aware that Mapping Lookup API is not intended for inserts/updates (since it doesn't contain any transacational handling), just mere lookups (selects in tables), so I'm not sure it is the best approach for your case.
Regards,
Henrique.

Query another message payload from graph mapping program

Hi all,
I have the following scenario
Third Party Business System -> XI -> ECC 5.0
Third Party sends ORDER to ECC and ECC answers with ORDRSP
When mapping ORDRSP.ORDERS05 to Third Pty format, I need to use info that the Third Party provided us on the ORDERS.
So... I have to query the ORDERS message payload from ORDRSP message mapping program.
Any ideas?
My first idea deal with doing an RFC lookup to search the ABAP Database for this info (my ABAP background raises ) but I'd like to know if there is a more elegant and efficent way of doing this.
regards,
David R.

Hi,
Let's try again to explain myself with my poor english!
Time frame
A) TPart system sends order. XI maps to ORDERS.ORDER05 idoc and is forwarded to ECC.
B) In ECC users modify Sales order and then triggers the outbound ORDRSP.ORDERS05.
C) XI has to map ORDRSP.ORDERS05 and include some info (in fact the original message) that was sent in step B).
The xmls from TPart could be (simplified version):
Orders (step A)
<?xml version="1.0" encoding="iso-8859-1">
<document>
<header>
</header>
<Items>
</Items>
<Items>
</Items>
</Header>
</Document>
The received XML on step C) could be something like this:
<?xml version="1.0" encoding="iso-8859-1">
<Document>
<PurchaseOrder_from_vendor>
<i>Here I have to include the whole xml sent in step A</i>
</PurchaseOrder_from_vendor>
<SalesOrder_from_customer>
<i>Here the ORDRSP.ORDERS05 mapping stuff</i>
</SalesOrder_from_customer>
</Document>
All the communication will be always async.
Any ideas?
regards,
David R.

Call another Message Interface from Java Mapping

Hi Gurus!!
I have designed a Java Mapping that does a Socket Connection. Before send the response of the Java Mapping, I have to send information to our SAP System.
I have see in a blog that I can call a RFC from the Java Mapping, but my doubt is, can I call another Message Interface designed on XI?
Thanks and regards,
Manuel Míguez.

That's tricky, since the proper way of doing it would be through BPM.
Anyway, if you expose your XI interface as a WebService (Soap sender cc) you could access it through Mapping Lookup (lookup works for RFC, DB and Soap lookups). Check https://help.sap.com/javadocs/NW04S/current/pi/index.html
But be aware that Mapping Lookup API is not intended for inserts/updates (since it doesn't contain any transacational handling), just mere lookups (selects in tables), so I'm not sure it is the best approach for your case.
Regards,
Henrique.

Terminate Message processing From UDF/mapping

i think u will be checking the condition first if its false then u will be raising alert.
wat u can do is when the condition fails u set the flag to false and send the output of UDF to ifwithoutelse statement and becuase of which ur mapping will not be processed.
u have to do it at root node level and u have to supress the target node when the condition fails.
chirag

wat exactly r u doing?
U have to first check all the condition at root level only before message get processed, based on that result u will stop the processing of message at the target end.
u ahve to set the falg in UDF and accordingly u need to suppress the target root node.
chirag

Multi Mapping issue - *Split mapping created no messages*

Hi,
The scenario I am trying to test is a multi mapping scenario where I am trying to split one source message and create two target messages by using two different inbound service interfaces, one for each message type.
I am on PI 7.1 and when I test message mapping and operation mapping using the payload from SXMB_MONI, it is successful. Whereas when I test the scenario end to end I am getting the following error messages:
Runtime error
*Split mapping created no messages*
Start tag ns0:MessagesStart tag ns0:Message1Close tag ns0:Message1Start tag ns0:Message2Close tag ns0:Message2Close tag ns0:Messages
Could someone please help
Cheers,
S

Hi,
(1)First change the occurrence of target message to 0..unbounded.
(2) Do the mapping and test it under test tab of mapping whether your mapping is working fine creating target records.
(3) Copy the source code from mapping and remove the unwanted tags "as Mark said " those were created due to multimapping.
Then test that file and that will work.
You can follow this link .
Link :Message Splitting
Thanks
Rabi
Edited by: RabiPanda on Nov 17, 2011 8:42 AM

Please help me to solve error: Split mapping created no messages

Hi Experts,
I am facing Split mapping created no messages when i run my scenario.
My Scenario is : Proxy to FILE.
I am triggering Proxy and based on one condition i am generating different Flat Files.
Now when i do this i am getting error :Split mapping created no messages in SXI_MONITOR.
When i check this in Message Mapping by taking data from SXI_MONI its working fine...
but when i trigger the data from RUNTIME WORKBENCH its throughing the error.
When i remove the NameSpaces <ns0:message>
and <ns0:messages1> its working fine.
How can i solve this issue.
Even though i removed Namespace in Message Type, i am getting the error.
I changed occurance of Target message to O..unbounded both in Message Mapping and Interface Mapping.
Its working fine in Message Mapping, problem occurs only when i run end-to-end scenario.
So please help me to solve this issue.

I think there might be mismatch between your name spaces.
may be this link might help you
Split mapping created no messages -Mluti Mapping
are you getting the same structure from your proxies whatever structure you have in your XI structure(sender) and NS should match.
but I dont have exp with proxies.
Sri

PI 7.30 Message Mapping with MsgSplit error Split mapping created no messages, cannot proceed.

Hi @all,
I am working on a scenario to split one soruce message with several items to 0..n message for the same receiver.
Therefore the occurrency of target message (signature in MM) have been adjusted.
Not all items are forwarded to receiver, only if the content meets some rules the item should be forwarded.
It could be that no item of the source message meet these rules and therefore no target message at all should be created.
During test of this case I am facing following error in RWB, scenario is setup as integrated configuration.
MappingException: Split mapping created no messages, cannot proceed. Review your mapping setup: splitting to 0 messages is not allowed.
As the occurrency of the target message is 0..n, 0 should be also valid and there should be no error in this case, just stop processing like if there is no receiver in receiver determination step (mode IGNORE)
Otherwise this will end up in lots of error messages which have to be analyzed and canceled manually which is quite time consuming.
Maybe someone faced the same issue and found a solution to get rid of this error message.
Best regards
Jochen

Hi Somil,
hi Sriram,
thanks for your response.
In my scenario there also multiple receiver applications receiving data from one single sender application. We are using PI 7.30 dual stack and major goal is to setup all scenario as integrated configurations to have java only processing. One reason for this setup is that the main support user do not have extensive PI knowledge so far and we want to keep it as simple as possible and therefore do not want them to care about the abap stack as much as possible.
Unfortunately migration to java only is not possible yet.
In this release extended receiver determination using operation mapping is not supported in integrated configuration.
There is quite complex rules to check if an item should be forward or not including lots of fields and also value mapping, so it would be quite difficult/impossible to write XPATH expression to have the same check during receiver determination step.
One workaround could be creating a dummy message in case of no item to be forward and root this message to different place (local file which is always to be overwritten)
Are there any alternatives/workarounds?
Best regards
Jochen
Message was edited by: Jochen Gugel

1:2 Message Mapping WithOut BPM - Split mapping created no messages Error

Hi,
I am a new-bie to SAP PI and am trying out the following scenario without BPM.
Make multiple files based on Age received from input file.Input File contains Name,DOB and Output File contains Name, Age.
I want to create 2 files, one containing details of people with Age <21 and the other output file containing details of people with Age >= 21.
To acheive this,
In IR, I created 2 DT and 3 MT,1 MM with 2 Target MT,both having occurences 0..unbounded, 1 IM with 2 Target MI,both having occurences 0..unbounded
And in ID, 1 Sender Agreement, 2 Receiver Agreement, 1 Receiver Determination, 1 Interface Determination using Enhanced Interface Determination.
When i run this scenario, I am getting the following error "Split mapping created no messages"
Please let me know how can I resolve it.

Oops, I did not know that.
Thanks for that information. uhuuuuuuuuuuu, atlast the message is processed and I am seeing output files created.
But, there is still one problem. My output files are created with just the following content
<?xml version="1.0" encoding="utf-8" ?>
<ns1:MT_2OP_File_Out xmlns:ns1="http://POC_Sec1_1IP2OP2" />
In MM, I see the output message as follows:
Message
     Message1
         MT_2OP_File_Out
              Employee
                  Name
                  Age
     Message2
         MT_2OP_File_Out1
              Employee1
                  Name
                  Age
The mapping done:
MT_2OP_File_Out and MT_2OP_File_Out with the Message Type element on source end.
Employee and Employee1 are mapped as
     Age -> removeContext -> SplitByValue[Each Value] < 21, Map Employee
     Age -> removeContext -> SplitByValue[Each Value] >= 21, Map Employee1 resp
The fields are straight maps.
Is there any basic mapping error that I am making. Please help.

Multi-Mapping "Split mapping created no messages"

Hi there
I have some issie when trying to create multiple messages from a single message. I am using file to file adapter and in the interface determination, enhanced config. Also my file structures are setup correctly. The inbound and outbound structure looks the same so theres no funny mapping used. I cheked my comm channels in the RWB and its fine and when I do a test config in the integration builder it complains about my interface determination but does not say whats wrong. Just the icon. I looked at some of the other blogs but they do not really help. Any ideas what this might be? The inbound message looks like this:
<?xml version="1.0" encoding="utf-8" ?>
- <ns:MT_Allocations_Reply_OUTB xmlns:ns="urn:metcash.co.za:test">
- <IDOC_Recordset>
- <IDOC_Structure>
<PLANT>134</PLANT>
<ORDER_NUM>50885006</ORDER_NUM>
<FILLER>1</FILLER>
<PLU_NUM>00000000074893650</PLU_NUM>
<QTY>000024.00</QTY>
<FILLER_2>j</FILLER_2>
</IDOC_Structure>
- <IDOC_Structure>
<PLANT>134</PLANT>
<ORDER_NUM>50885006</ORDER_NUM>
<FILLER>1</FILLER>
<PLU_NUM>00000000074893650</PLU_NUM>
<QTY>000024.00</QTY>
<FILLER_2>j</FILLER_2>
</IDOC_Structure>
- <IDOC_Structure>
<PLANT>134</PLANT>
<ORDER_NUM>50885006</ORDER_NUM>
<FILLER>1</FILLER>
<PLU_NUM>00000000074893650</PLU_NUM>
<QTY>000024.00</QTY>
<FILLER_2>j</FILLER_2>
</IDOC_Structure>
</IDOC_Recordset>
</ns:MT_Allocations_Reply_OUTB>
*And the Error:*
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- 
- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="">
<SAP:Category>XIServer</SAP:Category>
<SAP:Code area="MAPPING">GENERIC</SAP:Code>
<SAP:P1>Split mapping created no messages</SAP:P1>
<SAP:P2 />
<SAP:P3 />
<SAP:P4 />
<SAP:AdditionalText />
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack>Split mapping created no messages</SAP:Stack>
<SAP:Retry>M</SAP:Retry>
</SAP:Error>
Thanx,
Jan
Edited by: Jan de Lange on Nov 24, 2008 10:25 AM

I checked my config in the IR with the following payload, but is still only shows a stop icon on interface determination & mapping with no error trace:
<?xml version="1.0" encoding="utf-8" ?>
<ns:MT_Allocations_Reply_OUTB xmlns:ns="urn:metcash.co.za:test">
<IDOC_Recordset>
<IDOC_Structure>
<PLANT>134</PLANT>
<ORDER_NUM>50885006</ORDER_NUM>
<FILLER>1</FILLER>
<PLU_NUM>00000000074893650</PLU_NUM>
<QTY>000024.00</QTY>
<FILLER_2>j</FILLER_2>
</IDOC_Structure>
<IDOC_Structure>
<PLANT>134</PLANT>
<ORDER_NUM>50885006</ORDER_NUM>
<FILLER>1</FILLER>
<PLU_NUM>00000000074893650</PLU_NUM>
<QTY>000024.00</QTY>
<FILLER_2>j</FILLER_2>
</IDOC_Structure>
<IDOC_Structure>
<PLANT>134</PLANT>
<ORDER_NUM>50885006</ORDER_NUM>
<FILLER>1</FILLER>
<PLU_NUM>00000000074893650</PLU_NUM>
<QTY>000024.00</QTY>
<FILLER_2>j</FILLER_2>
</IDOC_Structure>
</IDOC_Recordset>
</ns:MT_Allocations_Reply_OUTB>

MAPPING GENERIC (Split mapping created no messages) error is sxmb_moni

Hello,
We are having thousands of messages failing in sxmb_moni due to MAPPING GENERIC error. It also states that <i>Split mapping created no messages</i>. Where will I start my investiagtion? I already checked both ID and IR but I could hardly determine what causes this error.
Here is a part of the error message from the trace:
<Trace level="2" type="T">......attachment XI_Context not found</Trace>
<Trace level="3" type="T">Mapping already defined in interface determination</Trace>
<Trace level="3" type="T">Object ID of Interface Mapping 6FB317EF58B136D6BEAB6E567934CC40</Trace>
<Trace level="3" type="T">Version ID of Interface Mapping A872F380930B11DAAB6EF47891374079</Trace>
<Trace level="1" type="T">Mapping-Object-Id:6FB317EF58B136D6BEAB6E567934CC40</Trace>
<Trace level="1" type="T">Mapping-SWCV:A872F380930B11DAAB6EF47891374079</Trace>
<Trace level="1" type="T">Mapping-Step:1</Trace>
<Trace level="1" type="T">Mapping-Type:JAVA</Trace>
<Trace level="1" type="T">Mapping-Program:com/sap/xi/tf/_GBO_MaterialMaster_StandardBusinessDocument_TO_LOCAL_Governor_</Trace>
<Trace level="3" type="T">Dynamic Configuration Is Empty</Trace>
<Trace level="3" type="T">Multi mapping required.</Trace>
<Trace level="3" type="T">Creating Java mapping com/sap/xi/tf/_GBO_MaterialMaster_StandardBusinessDocument_TO_LOCAL_Governor_.</Trace>
<Trace level="2" type="T">Call method execute of the application Java mapping com.sap.xi.tf._GBO_MaterialMaster_StandardBusinessDocument_TO_LOCAL_Governor_</Trace>
<Trace level="1" type="T">*** START APPLICATION TRACE ***</Trace>
<Trace level="3" type="T">Using existing</Trace>
<Trace level="3" type="T">Executing Query: SELECT TO_VALUE FROM ICC_MAPPING_VIEW WHERE FROM_CODING = SIRIUS AND TO_CODING = GS1 AND OBJECT = TRADE-ITEM-TYPE AND FROM_VALUE = 30</Trace>
<Trace level="1" type="T">SELECT TO_VALUE FROM ICC_MAPPING_VIEW WHERE FROM_CODING = SIRIUS AND TO_CODING = GS1 AND OBJECT = TRADE-ITEM-TYPE AND FROM_VALUE = 30 successfully returned: E-HPC_PRODUCTS</Trace>
<Trace level="1" type="T">ret: :E-HPC_PRODUCTS</Trace>
<Trace level="2" type="T">noReceiverFound</Trace>
<Trace level="1" type="T">*** END APPLICATION TRACE ***</Trace>
<Trace level="2" type="T">Java mapping com/sap/xi/tf/_GBO_MaterialMaster_StandardBusinessDocument_TO_LOCAL_Governor_ completed. (executeStep() of com.sap.xi.tf._GBO_MaterialMaster_StandardBusinessDocument_TO_LOCAL_Governor_</Trace>
<Trace level="3" type="T">Message Type 1 Number of Messages 0</Trace>
<Trace level="3" type="T">Message Type 2 Number of Messages 0</Trace>
<Trace level="1" type="E">CL_XMS_PLSRV_MAPPING~ENTER_PLSRV</Trace>
</Trace>
- <Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_LOG_TO_PERSIST">
<Trace level="3" type="T">No persisting of message after plsrv call, because of config</Trace>
</Trace>
<Trace level="3" type="System_Error">Error exception return from pipeline processing!</Trace>
<Trace level="1" type="B" name="CL_XMS_MAIN-WRITE_MESSAGE_TO_PERSIST" />
- 
Thanks in advance!

<Trace level="3" type="T">Using existing</Trace>
<Trace level="3" type="T">Executing Query: SELECT TO_VALUE FROM ICC_MAPPING_VIEW WHERE FROM_CODING = SIRIUS AND TO_CODING = GS1 AND OBJECT = TRADE-ITEM-TYPE AND FROM_VALUE = 30</Trace>
<Trace level="1" type="T">SELECT TO_VALUE FROM ICC_MAPPING_VIEW WHERE FROM_CODING = SIRIUS AND TO_CODING = GS1 AND OBJECT = TRADE-ITEM-TYPE AND FROM_VALUE = 30 successfully returned: E-HPC_PRODUCTS</Trace>
<Trace level="1" type="T">ret: :E-HPC_PRODUCTS</Trace>
<Trace level="2" type="T">noReceiverFound</Trace>
<Trace level="1" type="T">*** END APPLICATION TRACE ***</Trace>
You have used the Trace object to write some Trace in your User Defined Functions. Does this trace make sense in terms of your mapping logic to you?
Did you remove the <messages> tag from your source message?
Also, If you are using multimapping make sure that the mapping creates all the messages in the Target Side and that the Inbound adapter is neither Idoc nor HTTP.
Regards
Bhavesh

Split Mapping created no messages in SXMB_MONI

Hi All,
I have an IDOC to File scenario in which the target forms an XML file based on some RFC lookups. The problem i have is that whenever the RFC do not return any values, i am getting an "Split Mapping Created no messages" error in the SXMB_MONI. Is there any possible way that i could suppress the target and i should not form the target when the RFC do not return any output.
Regards,
Sherin Jose P

The problem i have is that whenever the RFC do not return any values
If you are trying to generate the Parent element using the RFC response then you are bound to get the error as no target structure will be poduced when the RFC does not return any value....may be doing a check on RFC response and then using MapWithDefault or any other term so that at least one valid element is produced will prevent the error from occuring.
Regards,
Abhishek.

Split mapping created.. No message exists

I see the above error message in Moni with a red flag
Actually, I dont think it really is an error message
becuase I have mapped in such a way that It shouldnt create any messages, if the condition fails.
Mapping:
If del_indicator exists ---> generate delete mapping
if del_indicator not exists ---> generate import mapping
this is the logic I did in Multi mapping.
so obviously delete will not generate if there s no deletion indicator.
the exact error message I see is "Split mapping created no messages"
there are no issues with output. its perfect.
but I still am able to see that error message in MONI
1. how do I control this? and remove the error message from moni?
2. why is it generating a error message?
Regards,
Nikhil.

If yes...so I have a solution for you !
But you will declare TWO Business Services for one receiver system:
.. Receiver_1
.. Receiver_2
you have to do some concessions as you do not want to use a BPM
In your Receiver Determination of ID, just write a condition based on your field "del_indicator".
in order to have something like that:
1. Sender --> Condition "del_indicator = Yes" --> Receiver_1
2. Sender --> Condition "del_indicator = No" --> Receiver_2
and then in the Interface Determination, you have:
1. Sender --> Mapping_for_delete_flow         --> Receiver_1
2. Sender --> Mapping_for_NON_delete_flow     --> Receiver_2
That means also that in your IR, you have TWO Interface Mappings:
1. Mapping_for_delete_flow     : Source --> Target_for_delete     (occurance 1 -> 1)
2. Mapping_for_NON_delete_flow : Source --> Target_for_NON_delete (occurance 1 -> 1)
Hope this help you.
Mickael

No messages created from split mapping

Similar Messages

Maybe you are looking for