Pinter enters unexplained start-up

Printer repeatedly goes into startup cycle when not in use for no apparent reason--day and night. Very annoying. What could cause this?

Thanks for the printer model. The Photosmart 7520 has a removable printhead and individual ink cartridges (IIC) style ink system. Typically, in this type of ink system, if the printer is repeatedly performing checks/cleaning procedures, then the printer doesn't have a secure connection with these parts.
I would advise removing all of the ink supplies, including the printhead, and cleaning the contacts. This process is known as an ink system reset and I have a thread with the steps outlined. To access this information click here.
As well, check the ink levels of the cartridges in the printer. This can be accessed by clicking on the Ink Drop symbol at the top of the touch display. How much does the printer indicate is in each cartridge?
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------
I am not an HP employee.

Similar Messages

I'm having problem with text boxes. Whenever i hit the enter button to start a new line or paragraph, the cursor doesn't drop down to the next line. Instead i get this little red + sign in the box.

I'm having problem with text boxes. Whenever i hit the enter button to start a new line or paragraph, the cursor doesn't drop down to the next line. Instead i get this little red + sign in the box.

You are absolutely right. Thought Enter meant Enter. I was wrong. Thank you for the help.
Rod Rogers, Broker
Accredited Land Consultant (ALC)
Metcalf Land Company, Inc.
Office: 864-585-0444
Mobile: 864-316-0297
Fax: 864-583-6000
<http://www.metcalfland.com> www.metcalfland.com

When ever enter the date start date up to next year same date between the days divided into 8 parts

when ever enter the date start date up to next year same date between the days divided into 8 parts
Q1.1 (YYYY) = 1st half of Quarter 1 for year YYYY
Q1.2 (YYYY) = 2nd half of Quarter1 for year YYYY
Q2.1 (YYYY) = 1st half of Quarter 2 for year YYYY
Q2.2 (YYYY) = 2nd half of Quarter 2 for year YYYY
Q3.1 (YYYY) = 1st half of Quarter 3 for year YYYY
Q3.2 (YYYY) = 2nd half of QuarterQ3 for year YYYY
Q4.1 (YYYY) = 1st half of Quarter 4 for year YYYY
Q4.2 (YYYY) = 2nd half of Quarter 4 for year YYYY
Here YYYY depicts the year.
e.g. Q1.2 (2014) depicts the 2nd half of Quarter 1 for year 2014.
The description of these values are explained below.
The table below provides the description about each value:
Quarter     Quarter Range      Start Date
Q1.1      1 Jan - 15 Feb         1st Jan
Q1.2      16 Feb-31 Mar         16th Feb
Q2.1      1 Apr- 15 May          1st Apr
Q2.2      16 May-30 June       16th May
Q3.1      1 Jul-15 Aug             1th Jul
Q3.2      16 Aug -30 Sep       16th Aug
Q4.1      1 Oct -15 Nov           1st Oct
Q4.2      16 Nov – 31 Dec      16th Nov
The dropdown values in time window needs to be updated as per date entered by the user in the Audit Plan start date and
should display the next four Quarter (each divided in 2 half i.e. Eight values ) along with the year from the selected Audit plan start date.
for eg. If the Plan start date is given as August 10 2013 then the Time window will display the following options:
Q3.2 (2013)
Q 4.1 (2013)
Q 4.2 (2013)
Q 1.1 (2014)
Q1.2 (2014)
Q2.1 (2014)
Q 2.2 (2014)
Q 3.1 (2014)
You can refer to the Table above and look that 10 Aug 2013 falls under the Q3.1 so Time window will display the next next 8 half Quarters ( Total 4 Quarter) till Q 3.1 for the year 2014.

Hello,
WITH half_quarters AS(
    SELECT ADD_MONTHS(TRUNC(DATE '2013-08-15','Q'), 3*(LEVEL - 1)) hq_start
           ,1 part
    FROM    dual
    CONNECT BY ROWNUM <= 5
    UNION ALL
    SELECT ADD_MONTHS(TRUNC(DATE '2013-08-15','Q'), 3*(LEVEL - 1) + 1) + 15 hq_start
           ,2 part
    FROM    dual
    CONNECT BY ROWNUM <= 5
,ordered_half_quarters AS(
    SELECT hq_start
           ,part
           ,ROW_NUMBER() OVER (ORDER BY hq_start) r
    FROM    half_quarters
    WHERE   hq_start > DATE '2013-08-15'
SELECT 'Q '||TO_CHAR(hq_start,'Q')||'.'||part||' ('||TO_CHAR(hq_start,'YYYY')||')' q
FROM    ordered_half_quarters
WHERE   r <= 8
ORDER BY r;
Q
Q 3.2 (2013)
Q 4.1 (2013)
Q 4.2 (2013)
Q 1.1 (2014)
Q 1.2 (2014)
Q 2.1 (2014)
Q 2.2 (2014)
Q 3.1 (2014)
half_quarters generates the start dates of every half of a quarter, starting with the begin of the first quarter that contains the sample date.
The next step is to order the dates and to select only those after the sample date.
The last part formats the output and orders the data.
Regards
Marcus

I try to sinc. first i get "computers not authorized, would you like to authorize. I do that then it tells me its already authorized. enter and it starts over.

I try to sinc. first i get "computers not authorized, would you like to authorize". I do that then it tells me its already authorized. enter and it starts over.

Google is amazing...
http://support.apple.com/kb/HT1420
also you can:
To deauthorize all computers associated with your account
Click iTunes Store in the Source pane.
If you’re not signed in to the store, click the Account button, then enter your account name and password.
Click the Account button again (your ID appears on the button), enter your password, and then click View Account.
In the Account Information window, click Deauthorize All.
After that start from scratch

Windows 7 How to unlock, and delete the necessity to enter password to start up computer?

Upon startup of computer, user name centered on screen, (the word LOCKED beneath it). How do I unlock, so it will start up without entering password?? Also, when I step away from the computer for a few minutes, when I return I must enter the password again. Any help would be greatly appreciated.

To disable logon screen after screensaver:
Open Screen Saver Settings by clicking the Start button , clicking Control Panel, clicking Appearance and Personalization, clicking Personalization, and then clicking Screen Saver.
De-Select the On resume, require logon check box, set a time after which to start the screen saver, and then click Apply.
To remove windows password for user accounts:
Click on Start and then Control Panel.
Click on the User Accounts and Family Safety link.
Click on the User Accounts link.
In the Make changes to your user account area of the User Accounts window, click the Remove your password link.
In the text box on the next screen, enter your current Windows 7 password.
Click the Remove Password button to confirm that you'd like to remove your Windows 7 password.
You can now close the User Accounts window.
Now that your Windows 7 account password has been deleted, you will no longer need to log on when your computer starts.
Your computer should now boot all the way to the Windows 7 desktop.
Signature:
I currently work on behalf of HP for numerous support departments. The opinions expressed above are the personal opinions of myself, not of HP. There is no guarantee that the opinions expressed are 100% correct.

The "Enter" key keeps starting and stopping itunes songs...

Hey, everytime I hit the enter key for example in Safari to enter a webpage, my itunes songs keep starting and stopping like I have the itunes window active... Does anyone know a solution for this? I tryed reinstalling and no luck...
Thanks

What are the system specs for your pc? It seems it's to slow to play iphone's 720p HD videos. QT 7.7.3 is the latest for windows but VLC Player will play these videos too.

Activity to enter task and start Workflow

Dear all,
I have copied template function "QM10_COPY_REFERENCE_FORM_TASK" to my customer namespace. Like in the FM documentation specified I changed the coding to this:
*- If you want to start a workflow task, you have to fill the container.
*- The following sample coding shows you what to do.
*- The lines beginning with *& represent the real coding, while
*- the other lines are commentary lines only.
*- For further information, refer to the function module documentation.
*---- include <cntn01>
    include <cntn01>.
*---- Data declaration
    swc_container my_container.
*---- Data initialisation
    swc_create_container my_container.
*---- Write the element to the container (The element names are used in
*---- the workflow E.g. 'QNOTIFICATION')
*---- 'element' represents the element name; 'value' represents
*---- the value of this element.
*---- If the element represents a table value, then the 'value'
*---- must also be a table.
*&    swc_set_element my_container 'element' 'value'.
    swc_set_element my_container 'NOTIFICATION' i_manum.
*---- Write the element to the container
*&    swc_set_table my_container '_Wi_Group_ID' i_manum.
*---- move my_container to te_container
    loop at my_container.
      append my_container to te_container.
    endloop.
In customizing I have entered the FM and as Workflow Task I entered "Workflow Template WS00200063 (QM ComplTask)". After pressing the activity in notification a task is entered. But after saving the notification a dump occurs (CALL_FUNCTION_REMOTE_ERROR, "Unable to create work item container (CL_SWF_RUN_WIM_FLOW->_IMPORT_CONTAINER)").
Has anybody an Idea what is wrong.
The only thing I want to archive is to start a workflow for a user when entering a task from activity.
If I enter the task manually (without activity FM) the workflow is starting right.
Thanks for any help.
Best regards
Roman
Edited by: Roman Becker on Jul 19, 2010 2:04 PM

Are there no ideas? Is there nobody with a similar configuration that works?
Best regards
Roman

Entering passwords on start-up

On my MBPro Lion, each time I start-up, there is a message for me that SafariIDVDclient wants to use the login keychain and requires me to enter my pasword.
Is there a way I can enter the pasword once without entering each time I start-up and if so, where can I do so?
Also, I receive a second message saying that iPhotoStreamAgent wants to use login keychain and requires me to enter my password for that as well as for the SafariiDVDclient.
Is there a place where I can enter the oasswird for the iPhotoStreamAgent without doing so each time?
Thanks for your help.
Vernon

Here's another quirk: after previous post, I entered System Preferences and had to enter my password there. I then clicked on iCloud I unchecked everything, including Photo Stream and shut down my MBPro. On start-up, no message came up requiring a password. I re-entered System Preferences and in iCloud I re-checked everything, shut-down and after start-up, I now have the same request for passwords appearing again.
So, there must be some link with iCloud.
Any suggestions?
Thanks for your help.
Vernon

HT201240 Hijust bought my brand new mac computer had all my files transferred from my old pc onto the new one and turn it on and it has a password to enter and get started i have tried my apple id password and another the store had written apple default

Hi
Just bought my brand new mac had all my files transferred from my old pc and now i try to start and it has a password that i cant get past
i have tried my apple password and another the dick smith store had on a piece of paper nothing works and the store isnt open easter sunday
can anyone help
Marj

Resetting User Password in Lion and Mountain Lion
Boot into your Recovery Partition by holding down the Command and R keys whilst booting.
When the Recovery screen appears, go to the Utilities menu and open Terminal.
In Terminal, type:
resetpassword
...a small app will open and allow you to choose the user for whom you want to change the password. If you are the admin, be certain that you choose your admin user. Type in your new password twice and give yourself a good hint. Click OK (or Done or whatever) and reboot, enjoying the use of your new, hopefully memorable, password.
Good luck,
Clinton

Unexplained full start-up disk

I just experienced a situation where an unknown task was writing to my start-up disk continuously until it was filled (0 bytes available). I forced a restart (power switch) and rebooted from a cloned back-up of the start-up (fortunately I had one that was only a few days old).
I inspected the original start-up drive and determined that the /Volumes folder (the mount point for other drives, and normally quite small)contained 50GB of material that appeared to be a (partial) copy of one of my other drives!
Has anyone else experienced this bizarre behaviour or have an explanation?
I have since used the clone to restore my start-up drive and everything is working normally now; I was just wondering if I had been a victim of some virus and I am afraid of a reoccurrence.
Thanks for any suggestions.

The most usual cause of a "false clone" being created in /Volumes is an interruption of the connection to the target volume during the cloning.
I presume you know that you can remove anything from /Volumes that is NOT an alias/link. If you need instructions, see http://forums.bombich.com/viewtopic.php?t=3852
It is NOT a virus.
Andreas (a moderator at the bombich forums)

I enter password after start, but password screen reappears

Screen is frozen after repeated off/on attempts.

roam wrote:
Mavericks is a bit like free beer. Everyone is grabbing it because it is free, guzzling it, and then complain they got a hangover.
Spelling corrected by: roam

Unexplained server re-starts

One of my clients has OSX Server (10.4.3) running on a Dual G5 with 2.5Gb RAM. He experiences unexplained re-starts. Sometimes these occur during the night when no-one is logged in and sometimes during the day with users logged-in. When the problem occurs during the day it is often preceeded by partial loss of connectivity for clients. The server ran well for several weeks after installation before beginning to suffer these problems.
Any help or suggestions would be most welcome.
Here is one of the logs:
panic(cpu 0 caller 0x000E6D70): vnode_put(3f5e6b4): iocount < 1
Latest stack backtrace for cpu 0:
Backtrace:
0x00095544 0x00095A5C 0x0002683C 0x000E6D70 0x000E6D1C 0x000D3798 0x002A7A94 0x000ABCB0
0x7C0803A6
Proceeding back via exception chain:
Exception state (sv=0x5C0C7A00)
PC=0x9001BF00; MSR=0x0000D030; DAR=0x40FC0040; DSISR=0x40000000; LR=0x90B0BA6C; R1=0xF0201710; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.2.0: Fri Jun 24 17:46:54 PDT 2005; root:xnu-792.2.4.obj~3/RELEASE_PPCModel: PowerMac7,3, BootROM 5.2.4f1, 2 processors, PowerPC G5 (3.0), 2.3 GHz, 2.5 GB
Graphics: ATI Radeon 9600, ATY,RV351, AGP, 128 MB
Memory Module: DIMM0/J11, 256 MB, DDR SDRAM, PC3200U-30330
Memory Module: DIMM1/J12, 256 MB, DDR SDRAM, PC3200U-30330
Memory Module: DIMM2/J13, 1 GB, DDR SDRAM, PC3200U-30330
Memory Module: DIMM3/J14, 1 GB, DDR SDRAM, PC3200U-30330
Network Service: Built-in Ethernet, Ethernet, en0
PCI Card: ATTO ExpressPCI UL4S, scsi-2, SLOT-2
PCI Card: ATTO ExpressPCI UL4S, scsi-2, SLOT-2
Serial ATA Device: ST3400832AS, 372.61 GB
Serial ATA Device: ST3400832AS, 372.61 GB
Parallel ATA Device: SONY DVD RW DW-Q28A,
SCSI Device: SCSI Target Device @ 5,
SCSI Device: SCSI Target Device @ 6,
USB Device: Hub in Apple Pro Keyboard, Mitsumi Electric, Up to 12 Mb/sec, 500 mA
USB Device: Apple Optical USB Mouse, Logitech, Up to 1.5 Mb/sec, 100 mA
USB Device: Apple Pro Keyboard, Mitsumi Electric, Up to 12 Mb/sec, 250 mA
G4 QuickSilver 800DP Mac OS X (10.4.5)

There isn't enough information in your post to be able to formulate an answer. Clearly the CPU panicked but there's no clue as to why.
Random panics can be caused my many things, including faulty RAM, overheating, flaky power supply, and more.
What would be more useful are the logs before the crash and the entire reboot log since it might provide more clues.
I'd also upgrade to 10.4.5. There's no reason to be two revisions behind the curve in system updates.

ThinkPad Twist - I can not start the bios or the start-up menu pressing Enter

Think Pad Twist i7-3537U
No matter how fast or how many times I press the enter key when starting, I can not access the start-up menu.
Immediately after the white "ThinkPad - To interrupt normal start press Enter" letters appear for just a fraction of a second on the bottom left corner, there comes the windows blue logo, and windows starts.
- The enter key is working fine (I can use it with any application)
- I am completely shutting down the laptop, not sleeping or hibernating.
- I have tried a "safe mode" start from msconfig -> same results.

Ok, I've been able to access the BIOS with the following procedure:
http://www.makeuseof.com/tag/how-to-access-the-bios-on-a-windows-8-computer/
Winkey+C > PC Settings > General > Advanced Startrup > Restart Now > > > UEFI Settings
But this is only a temporary solution. What will happen if I can not start Windows and I need to access the Startup for recovery purposes?, or to boot from a USB device?
I would like to have a solution to normally access the Startup Options pressing the Enter key.
Thank You

I am trying to do a full Time Machine Backup to a new external disk. The backup starts, and it says "Time remaining about 4 days." That seems like a very long time, but the real problem is that the computer "logs off" after a few hours, and the b.u. stops

I am trying to do a full Time Machine Backup to a new external disk. The backup starts, and it says "Time remaining about 4 days." That seems like a very long time, but the real problem is that the computer "logs off" after a few hours, and the backup stops. The system preferences are set to "Never" for Computer sleep and Display sleep. The computer does not ordinarily log off automatically, but it has done this twice since I started the Time Machine backup.

If you have more than one user account, these instructions must be carried out as an administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Enter the word "Starting" (without the quotes) in the String Matching text field. You should now see log messages with the words "Starting * backup," where * represents any of the words "automatic," "manual," or "standard." Note the timestamp of the last such message. Clear the text field and scroll back in the log to that time. Select the messages timestamped from then until the end of the backup, or the end of the log if that's not clear. Copy them (command-C) to the Clipboard. Paste (command-V) into a reply to this message.
If all you see are messages that contain the word "Starting," you didn't clear the search box.
If there are runs of repeated messages, post only one example of each. Don't post many repetitions of the same message.
When posting a log extract, be selective. Don't post more than is requested.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Some personal information, such as the names of your files, may be included — anonymize before posting.

Contract Start and End Dates in Sales Order

Hi
I have a situation where a service item is bundled with a deliverable item. The order is as follows
Line Item    Mat                                                                 Qty            Higher Level Item
10              Item No.1 (Physical Item)                                  1
20              Item No.2 (Service Item)                                    1               10
For the deliverable item 10 , Revenue is recognized immediately. For the Service item no.20 , revenue needs to be recognized over a period of 1 Year (It is a 1 year service contract).
The whole order is created via BAPI from an external 3rd party order capture system.
In order to do revenue recognition properly for service items , SAP I believe has 2 options
1. Based on Billing plan dates
2. Based on contract start dates
Since order with both the line items need to produce 1 invoice, I cannot use billing plan . The only other option is to use contract start and end dates. I have enabled contract data at the sales order level. So when I enter the contract start and end dates manually at the line item level and set the item category to recognize revenue based on contract start and end dates based on time-based revenue recognition it is working fine.
But I need a way to automate the population of contract start and end dates at the line item level. My ABAP guy is not able to find a user exit that can change the XVEDA or any VEDA structure in any of the user exits.
I guess the SAP SD gurus out there would have definitely dealt with a situation of product bundling (Service and non-service items in the same sales order with one billing document , but seperate revenue recognition for service and non-service items)
Please help.
Thnx
Siva

Hi Siva,
Kindly let me know what criteria you want to give for automatic population of start date of contract...
Standard SAP comes with a few baseline dates for contract start date and we can control this from customization itself.
01     Today's date
02     Contract start date
04     Acceptance date
05     Installation date
06     Date contract signed
07     Billing date/Invoice date
08     CntrctStDate+contract duration
09     Contract end date
If you have some criteria which is not covered here, then let me know and i will try to provide some help then.
Thanks
Kapil Sharma

Pinter enters unexplaine​d start-up

Similar Messages

Maybe you are looking for

Pinter enters unexplained start-up